Filtry
wszystkich: 2555
wybranych: 2093
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: force-deformation spectroscopy
-
Simple colorimetric copper(II) sensor – spectral characterization and possible applications
PublikacjaNew o-hydroxyazocompound L bearing pyrrole residue was obtained in the simple synthetic protocol. The structure of L was confirmed and analyzed by X-ray diffraction. It was found that new chemosensor can be successfully used as copper(II) selective spectrophotometric regent in solution and can be also applied for the preparation of sensing materials generating selective color signal upon interaction with copper(II). Selective colorimetric...
-
The Application of Vibration Recording and Analysis in Tribological Research on Sliding Friction
PublikacjaThe paper reports on a tribological research on the macroscopic manifestation and characteristics of sliding friction. The aim of the task was to measure friction in lubricated sliding contacts and test the interactions between the environment (the test rig) and the experimental friction contact. Friction-induced vibrations were observed and studied as a manifestation of the process. The typical set of velocity and force/torque...
-
Experimental Study of Dapped-End Beams Subjected to Inclined Load
PublikacjaThis paper presents the results of an experimental investigation of the reinforced concrete (RC) dapped-end beams loaded with inclined forces, compared to identical ones loaded with vertical forces only. Such a load may occur in, for example, Gerber's joints or in dapped-end beams supported on corbels, where the vertical gravitation force is additionally completed with horizontal forces caused by temperature differences, shrinking,...
-
The shadowing chain lemma for singular Hamiltonian systems involving strong forces
PublikacjaW niniejszym artykule rozważamy autonomiczny układ Hamiltonowski na płaszczyźnie z potencjałem, który ma punkt osobliwy (studnię nieskończonej głębokości) i maksimum globalne właściwe równe zero przyjmowane w dwóch różnych punktach płaszczyzny. Przy założeniu, że w otoczeniu punktu osobliwego potencjał spełnia warunek Gordona(gradient tego potencjału w otoczeniu punktu osobliwego jest tzw. silną siłą, ang. a strong force) dowodzimy...
-
Trim Optimisation - Theory and Practice
PublikacjaForce Technology has been working intensively with trim optimisation tests for almost last 10 years. Focus has primarily been put on the possible power savings and exhaust gases reduction. This paper describes the trim optimisation process for a large cargo vessel. The physics behind changed propulsive power is described and the analyses in order to elaborate the optimum trimmed conditions are presented. Different methods for prediction...
-
On the Nonlinear Effects of Magnetoacoustic Perturbations in a Perfectly Conducting Viscous and Thermoconducting Gas
PublikacjaNonlinear effects of planar and quasi-planar magnetosound perturbations are discussed. The plasma is as- sumed to be a Newtonian thermoconducting gas with infinite electrical conductivity permeated by a magnetic field orthogonal to the trajectories of gas particles. Generation of the non-wave modes (magnetoacoustic heating and streaming) in the field of periodic and aperiodic magnetoacoustic perturbations is discussed. The results...
-
Knowledge work and knowledge workers in knowledge-based economy - theoretical considerations
PublikacjaIt is often claimed that an organization is as good as people working in it and that talented workers are the driving force of an organization. To cope with the growing requirements of knowledge-based economy, organizations need a special type of workers - knowledge workers. This is especially important in organizations building their competitive advantage on innovations and the application of information and communication technologies...
-
ANALYSIS OF BRACE STIFFNESS INFLUENCE ON STABILITY OF THE TRUSS
PublikacjaThe paper is devoted to the numerical and experimental research of stability of a truss with side elastic supports at the top chord. The structure is a model of a real roof truss scaled by factor ¼. The linear buckling analysis and non-linear static analysis were carried out. The buckling length factor for the compressed top chord was calculated and the limit load for the imperfect truss shell model with respect to brace stiffness...
-
The impact of end-user participation in IT projects on product usability
PublikacjaMany companies implementing new IT projects encounter numerous problems with ensuring good final product usability. The strong market competition they experience often results in necessity of undertaking difficult decisions with regard to cost minimization. This may force cuts in usability expertise and consulting, most often by limiting end-user participation in the project. However, it may also result in serious consequences...
-
A two dimensional approach for modelling of pennate muscle behaviour
PublikacjaThe purpose of this study was to elaborate a two-dimensional approach for unipennate and bipennate striated skeletal muscle modelling. Behavior of chosen flat pennate muscle is modelled as a rheological system composed of serially linked passive and active fragments having different mechanical properties. Each fragment is composed of three elements: mass element, elastic element and viscous element. Each active fragment furthermore...
-
Effect of the let-through energy of overcurrent protective devices on the temperature of conductors during short-circuits
PublikacjaThe scope of the verification of low-voltage systems covers the earth fault loop impedance measurement. This measurement is usually performed with the use of low-value current meters, which force a current many times lower than the one occurring during a real short-circuit. Therefore, the international standard recommends consideration of the increase of resistance of conductors with the increase of temperature, which may occur...
-
Effect of cobalt addition on the corrosion behaviorof near equiatomic NiTi shape memory alloy in normal saline solution: electrochemical and XPS studies
PublikacjaThe electrochemical and corrosion (uniform and localized) behavior of a binary Ni52Ti48 shape memory alloy (SMA) and two ternary Ni52Ti48-xCox (x = 1.5 and 4.0 wt.%) SMAs were studied. Measurements were conducted in 0.9% NaCl solution at 37 oC employing various electrochemical methods. These include: linear polarization resistance (LPR), linear sweep voltammetry (LSV), chronoamperometry and dynamic electrochemical impedance spectroscopy...
-
Role of MnO in manganese–borate binary glass systems: a study on structure and thermal properties
PublikacjaStructural and thermal properties of x MnO−(100−x)B2O3 (where x=40, 50 and 60 mol%) glass samples have been investigated with the employment of various techniques. Fourier transform infrared spectroscopy results revealed the influence of MnO on glass matrix. Decrease of B–O bond-related band intensities has been observed. MnO addition was found to introduce broken [BO2O−]n chains. Differential scanning calorimetry (DSC) measurements...
-
The effect of nitrogen on the structure and thermal properties of beryllium-containing Na-(Li)-Si-O-N glasses
PublikacjaTwo oxynitride glass series with the composition of 35Na2O-5BeO-(60-x)SiO2-xSi3N4 and 9Li2O- 27Na2O-5BeO-(59-x)SiO2-xSi3N4, were prepared. The glasses' topography and structure were studied by Scanning Electron Microscopy and Raman spectroscopy. The composition was analyzed by Inductively Coupled Plasma Optical Emission Spectrometer, SEM-EDS and nitrogen and oxygen elemental analyzer. Na-(Li)-Be-silicate glasses were found to contain...
-
Synthesis, thermal, structural and electrical properties of vanadium-doped lithium-manganese-borate glass and nanocomposites
PublikacjaA glassy sample with a nominal formula LiMn1−3x/2VxBO3 (where x = 0.05) was synthesised using the melt-quenching method. Material was characterised by differential thermal analysis (DTA), X-ray diffactometry (XRD) at room temperature and as a function of temperature (HT-XRD), X-ray photoelectron spectroscopy (XPS), impedance spectroscopy (IS) and scanning electron microscopy (SEM). Dependences of glass transition and crystallisation...
-
Investigation of the structural and thermal properties of aluminum-rich Ca–Al–Si–O–N glasses
PublikacjaIn this paper, we investigate the structure and thermal properties of aluminum-rich transparent Ca–Al–Si–O–N glasses. The obtained glasses were prepared by a traditional melt-quenching technique at 1650 °C using AlN as the nitrogen source. The obtained glasses have a nAl/nSi>1 and contain up to 17 eq.% of N. The structure of the glasses was characterized by X-ray diffraction, X-ray photoelectron spectroscopy, infrared, and Raman...
-
Aggregation of imidazoacridinones - spectroscopic and microcalorimetric approach
PublikacjaImidazoacridinones (IA) belong to a group of polycyclic heteroaromatic antitumor compounds. IA create the aggregated form in water solution. Self-association of substances is a very important phenomenon in many fields of applied chemistry. It is also fundamental model reaction of many kinds of molecular interactions such as the micelle formation of amphiphilic substances and the binding of small organic molecules to macromolecules....
-
Multivariate analysis of impedance data obtained for coating systems of varying thickness applied on steel
PublikacjaElectrochemical impedance spectroscopy (EIS) has proven to be a valuable test method for the electrochemical characterization of protective coatings on metals. The common way of analysis in impedance spectroscopy is to model the impedance spectrum by means of an equivalent circuit and to extract the quantity of interest using optimization techniques. A model, corresponding to the behavior of the sample under testing, is important...
-
Proton transfer and hydrogen bonds in supramolecular, self-assembled structures of imidazolium silanethiolates. X-ray, spectroscopic and theoretical studies
PublikacjaThe reaction of 1-methylimidazole, 2-ethyl-4-methylimidazole and 2-ethylimidazole with tris(2,6- diisopropylphenoxy)silanethiol (TDST) leads to the formation of three new salts, which have been characterized by elemental analyses, thermogravimetric analyses, FTIR spectroscopy, and their structures were determined by single-crystal X-ray diffraction. Structural analyses indicate that in all three compounds a proton transfer has...
-
Quantitative fluorescent determination of DNA – Ochratoxin a interactions supported by nitrogen-vacancy rich nanodiamonds
PublikacjaOchratoxin A (OTA) is a hazardous contaminant of a large variety of plant and animal originated food. Herein, we report an interaction of OTA with calf thymus DNA (ct DNA) on the nanodiamond surface. We employed multispectroscopic techniques to elucidate the binding mechanism of OTA with ct DNA. The fluorescence and UV–Vis spectroscopy results show that OTA binds to ds ct DNA and forms complexes. We obtained the binding constants...
-
Effect of double thermal and electrochemical oxidation on titanium alloys for medical applications
PublikacjaThe research focuses on the development and characterization of innovative thin hybrid oxide coatings obtained in subsequent processes of thermal (TO) and electrochemical (EO) oxidation. Four different surface modifications were investigated and the microstructure was determined, the mechanical, chemical and biological properties of the Ti-13Nb-13Zr alloy were assessed using scanning electron microscopy, X-ray dispersion analysis,...
-
Tuning the photocatalytic performance through magnetization in Co-Zn ferrite nanoparticles
PublikacjaIn this work, the link between the photocatalytic performance of Co-Zn ferrite nanoparticles and the net magnetic moment is analyzed. CoxZn1-xFe2O4 nanoparticles (0 ≤ x ≤ 1) were synthesized by co-precipitation method and different physicochemical techniques were employed to characterize the samples (X-ray diffraction, Transmission Electron Microscopy (TEM), BET surface area, Diffuse Reflectance Spectroscopy (DRS), Photoluminescence spectroscopy,...
-
Novel Class of Proton Conducting Materials—High Entropy Oxides
PublikacjaHere, for the first time, we present data on proton conductivity of high-entropy, single-phase perovskites. The BaZr0.2Sn0.2Ti0.2Hf0.2Ce0.2O3−δ, BaZr0.2Sn0.2Ti0.2Hf0.2Y0.2O3−δ, BaZr1/7Sn1/7Ti1/7Hf1/7Ce1/7Nb1/7Y1/7O3−δ, and BaZr0.15Sn0.15Ti0.15Hf0.15Ce0.15Nb0.15Y0.10O3−δ single-phase perovskites were synthesized. Before electrical measurements, materials were characterized using X-ray diffraction (XRD), scanning electron microscopy...
-
Intramolecular interactions in crystals of tris(2,6-diisopropylphenoxy)silanethiol and its sodium salts
PublikacjaHydrolytically stable tris(2,6-diisopropylphenoxy)silanethiol has been obtained and reacted with sodium. Solid state interactions within and between the molecules of tris(2,6-diisopropylphenoxy)silanethiol including S-H---π-interactions between the S-H unit and the π-system of the arene have been analyzed. The interactions are documented by X-ray diffraction and FT-IR spectroscopy.
-
The mechanism of grouting action under the base of bored pile
PublikacjaThe grouting under the base of bored pile is carried out in order to reduce pile settlement and improve its bearing capacity. The principal aim of grouting is to introduce an initial force between the soil and the pile base. In non-cohesive soil, the grouting can also enlarge the pile base area and therefore improve the base resistance. The example of static load tests on instrumented bored piles installed with and without grouting...
-
Sensorless induction motor drive with voltage inverter and sine-wave filter
PublikacjaThis paper presents a speed sensorless control system of an induction motor with an output LC filter. It is known that the parameters design of the filter gives sine wave motor supply voltage but complicates control and estimation process. The reason is that the voltage drop and phase shift between filter input and output signals are imposed, and hence the motor voltages and currents differ from the inverter output waveforms. To...
-
Optimizing the computation of a parallel 3D finite difference algorithm for graphics processing units
PublikacjaThis paper explores the possibilities of using a graphics processing unit for complex 3D finite difference computation via MUSTA‐FORCE and WENO algorithms. We propose a novel algorithm based on the new properties of CUDA surface memory optimized for 2D spatial locality and compare it with 3D stencil computations carried out via shared memory, which is currently considered to be the best approach. A case study was performed for...
-
Connecting orbits for a periodically forced singular planar Newtonian system
PublikacjaW niniejszym artykule badamy problem istnienia i krotności rozwiązań homoklinicznych i heteroklinicznych dla nieautonomicznych układów Newtonowskich na płaszczyźnie z potencjałem okresowym ze względu na zmienną czasową, mającym maksimum globalne właściwe przyjmowane w dwóch punktach płaszczyzny i punkt osobliwy (studnię nieskończonej głębokości), w otoczeniu którego potencjał spełnia warunek Gordona (gradient potencjału ze względu...
-
The networking of the justice system as part of public court networks
PublikacjaThe goal of this paper is to look at the organizational structure of the justice system and provide the answer to the basic question of the possible network relations, their force, and imapct. As part od the paper, I have defined public inetrorganisational court network, dividing them into regulatory inter-organisational networks nad voluntary inetrorganisational networks. Emphasis has also been placed on the benefits and threats...
-
Identification of diagnostic parameter sensitivity during dynamic processes of a marine engine
PublikacjaChanging some parameters of the engine structure alters the emission of harmful components in the exhaust gas. This applies in particular to the damage of charge exchange system as well as fuel system and engine supercharger. These changes are much greater during the dynamic states and their accompanying transitional processes. The different sensitivity of diagnostic parameters to the same force, coming from the engine structure, but...
-
Properties of Nasicon-based CO2 sensors with Bi8Nb2O17 reference electrode
PublikacjaPotentiometric CO2 sensors based on Nasicon (Na+ conductor, Na3Zr2Si2PO12) electrolyte, Bi8Nb2O17/Pt reference electrode and different sensing electrodes have been prepared. Besides the sensing electrode material, sensors differ from each other in the reference electrode preparation technique. The main aim of this study is to investigate sensor construction and electrode fabrication process influence on sensor properties. The optimal...
-
Two tests for adhesive bonding long term characterization: principles and applications
PublikacjaThis article describes recent refinement of the traditional wedge test technique used to characterize durability of the adhesive joints. We propose two types of measuring protocols to monitor precisely and continuously the propagation of an "effective" crack during long term mode I fracture mechanic test. First method is directly derived from the traditional wedge test technique and consist in monitoring the surface strain of adherent...
-
INVESTIGATION OF JOURNAL SLIDE BEARINGS UNDER THE ANGLE OF THEIR FUNCTIONING
PublikacjaPaper presents the structure and principle of operation of a stand for measurements of influence of the lubrication method and process on functioning of journal slide bearings in their various technical states. Measurements performed on the stand make it possible to take advantage of the new method of evaluating the influence of physical and chemical properties of lubricating oil on the coefficient of friction in the mixed friction...
-
Selected aspects of the evolution of the industry analysis
PublikacjaPorter's five forces is a significant tool of analysis of industries. It helps evaluating variables of industry profitability and assessing firm performance. Using the framework, managers can take a decision as to which industries they can effectively compete in and position their companies to reduce the adverse effects of the mentioned forces. According to the critics, the five forces model is limited to its static nature. The...
-
Comparative tests of the wall thickness effect of a glass-reinforced thermosetting plastic coating with a non-circular cross section in a soil-coating object for economic aspect
PublikacjaCulvert structures made of plastics are employed extensively in the construction of new facilities as well as the renovation of existing ones. Due to the high costs of materials required for the manufacturing of these goods, the objective of this research is focused to lessen the thickness of the walls, which may, on the other hand, result in a reduction in the stiffness of the system. In the course of the testing, the structure...
-
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublikacjaProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
On the plastic buckling of curved carbon nanotubes
PublikacjaThis research, for the first time, predicts theoretically static stability response of a curved carbon nanotube (CCNT) under an elastoplastic behavior with several boundary conditions. The CCNT is exposed to axial compressive loads. The equilibrium equations are extracted regarding the Euler–Bernoulli displacement field by means of the principle of minimizing total potential energy. The elastoplastic stress-strain is concerned...
-
Thermal Buckling Analysis of Circular Bilayer Graphene sheets Resting on an Elastic Matrix Based on Nonlocal Continuum Mechanics
PublikacjaIn this article, the thermal buckling behavior of orthotropic circular bilayer graphene sheets embedded in the Winkler–Pasternak elastic medium is scrutinized. Using the nonlocal elasticity theory, the bilayer graphene sheets are modeled as a nonlocal double–layered plate that contains small scale effects and van der Waals (vdW) interaction forces. The vdW interaction forces between the layers are simulated as a set of linear springs...
-
Enhanced visible light photocatalytic activity of Pt/I-TiO2 in a slurry system and supported on glass packing
PublikacjaHighly photoactive I/TiO2, Pt/I-TiO2 nanocomposites were obtained using a hydrothermal and wet impregnation method. The incorporation of iodine and modification with 0.05 mol% of platinum leads to enhanced photocatalytic activity as compared to singly doped TiO2 due to the presence of impurity energy level in the structure of TiO2. X-ray diffraction, TEM microscopy, UV–Vis spectroscopy, X-ray photoelectron spectroscopy and BET...
-
The Analysis of Vodka: A Review Paper
PublikacjaVodka is the most popular alcoholic beverage in Poland, Russia and other Eastern European countries, made from ethyl alcohol of agricultural origin that has been produced via fermentation of potatoes, grains or other agricultural products. Despite distillation and multiple filtering, it is not possible to produce 100 % ethanol. The solution with a minimum ethanol content of 96 %, which is used to produce vodkas, also contains trace amounts...
-
Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ on structural, electrical, and electrochemical properties for potential oxygen electrode of intermediate temperature solid oxide cells
PublikacjaThis work presents the results of a comprehensive study on the impact of the A-site non-stoichiometry of SrxTi0.3Fe0.7O3-δ (x = 0.90, 0.95, 1.00, 1.05) ceramics on their physicochemical properties. The materials were fabricated by the conventional solid-state reaction method and their structure was determined by X-ray diffractometry, X-ray photoelectron spectroscopy and electron microscopy. Their sintering and thermal expansion...
-
The Effect of Titanium Oxyfluoride Morphology on Photocatalytic Activity of Fluorine-Doped Titanium(IV) Oxide
PublikacjaTitanium oxyfluoride (TiOF2) is a metastable product that can be obtained in a fluorine-rich environment. This material can also be a valuable precursor in the synthesis of titanium(IV) oxide (TiO2). However, the effect of TiOF2 morphology on the physicochemical properties of TiO2 has not been studied so far. In this work, single-phase TiOF2 was prepared by a solvothermal method. The as-synthesized samples exhibited a variety of...
-
Enhanced photoelectrochemical performance of inorganic-organic hybrid consisting of BiVO4 and PEDOT:PSS
PublikacjaThe PEDOT:PSS (poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)) was electrodeposited on a thin layer of bismuth vanadate (BiVO 4 ) prepared using the pulsed laser deposition technique onto FTO. The inorganic-organic junction was characterized by Raman spectroscopy, UV-Vis spectroscopy and sc anning electron microscopy. Chronoamperometry curves, recorded under simulated solar light illumination,...
-
Changes on the Surface of the SiO2/C Composite, Leading to the Formation of Conductive Carbon Structures with Complex Nature of DC Conductivity
PublikacjaSol–gel layers have been the subject of many studies in recent decades. However, very little information exists about layers in which carbon structures are developed in situ. Using the spin-coating method, we obtained thin iron-doped SiO2/C composite films. The results of Raman spectroscopy showed that our samples consisted of graphitic forms and polymers. The latter’s contribution decreases with rising temperature. FTIR and EDS...
-
Photochemical Rearrangement of a 19-Membered Azoxybenzocrown: Products and their Properties
PublikacjaThe preparation and characterization of products of the chemical and photochemical rearrangements of a 19-membered o,o'-azoxybenzocrown were presented. In photochemical rearrangement, besides expected product i.e. 19-membered o-hydroxy-o,o'-azobenzocrown (19-o-OH), obtained under defined conditions with 75% yield, also other macrocyclic products were isolated and identified, namely: 19-membered p-hydroxy-o,o'-azobenzocrown (19-p-OH),...
-
Frequency Diagnostics of Transformer Insulating Parameters
PublikacjaIn the article is presented experimental analysis and diagnostics of insulating system oil-paper for power transformers, mainly by progressive frequency method – dielectric spectroscopy. In the 1-st part of the article is described base theory about measurement and diagnostics insulating part (oil and paper) of power transformers. In the 2-nd part of article is described measuring method of insulating frequency diagnostics - frequency...
-
The Effect of Sodium Tetrafluoroborate on the Properties of Conversion Coatings Formed on the AZ91D Magnesium Alloy by Plasma Electrolytic Oxidation
PublikacjaMagnesium and its alloys are widely used in many areas because of their light weight, excellent dimensional stability, and high strength-to-weight ratio. However, the material exhibits poor wear and corrosion resistance, which limits its use. Plasma electrolytic oxidation (PEO) is an effective surface modification method for producing ceramic oxide layers on Mg and their alloys. The influence of the additions of sodium tetrafluoroborate...
-
Longitudinal Motion Due to Action of Tunnel Thrusters
PublikacjaTunnel thrusters are propulsion and active control devises that provide a side force, or transverse thrust, to support mooring operations or position keeping. They shorten the time of manoeuvring, reduce the cost of towage and since inception, manoeuvrability specifically in ports has become a lot easier. Tunnel thrusters can either be operated manually or with the help of Dynamic Positioning systems which makes it even more efficient. Theoretically,...
-
A Simple Neural Network for Collision Detection of Collaborative Robots
PublikacjaDue to the epidemic threat, more and more companies decide to automate their production lines. Given the lack of adequate security or space, in most cases, such companies cannot use classic production robots. The solution to this problem is the use of collaborative robots (cobots). However, the required equipment (force sensors) or alternative methods of detecting a threat to humans are usually quite expensive. The article presents...
-
Novel decahedral TiO2 photocatalysts modified with Ru or Rh NPs: Insight into the mechanism
PublikacjaNovel decahedral TiO2 modified with Ru or Rh NPs were successfully synthesized by hydrothermal method. The effect of metal type as well as amount of noble metal precursor (0.05, 0.1, 0.2, 0.3 and 0.5 wt.%) on the photocatalytic activity were investigated. Decahedral TiO2 decorated by Ru and Rh nanoparticles was prepared by photodeposition method, whereas Rh doped TiO2 was obtained by onestep hydrothermal method with introduction...