Filtry
wszystkich: 886
wybranych: 728
Wyniki wyszukiwania dla: measurement methods
-
Measurement of Latency in the Android Audio Path
PublikacjaThis paper provides a description of experimental investigations concerning comparison between the audio path characteristics of various Android versions. First, information about the changes in each system version in the context of latency caused by them is presented. Then, a measurement procedure employing available applications to measure latency is described comparing to results contained in the Internet. Finally, a comparison...
-
Low-coherence method of hematocrit measurement
PublikacjaW artykule opisano niskokoherencyjna metodę pomiaru hematokrytu krwi.
-
On-line measurement of wood surface smoothness
PublikacjaThe latest progress in the field of optics and microelectronics resulted in development of new generation vision systems capable of scanning surface topography with very high sampling frequencies. The blue color of illuminating light as well as novel systems for controlling ultra-thin laser line thickness allows measurement of the porous surface of wood with a triangulation method. Three alternative sensors were tested here in...
-
Measurement cell - current density analysis.
PublikacjaW pracy przedstawiono model celki do pomiarów elektrycznych parametrów szkliwa i innych tkanek zęba. Wyniki otrzymano za pomocą metody elementu skończonego. Wykazano, że możliwa do osiągnięcia dokładność pomiaru jest zdeterminowana przez prąd upływu celki.
-
Comparison of noise reduction methods in radiometric correlation measurements of two-phase liquid-gas flows
PublikacjaTwo-phase liquid-gas flows occur frequently in the mining, energy, chemical, and petrochemical industries. One of non-contact methods used to analyse these flows is the gamma ray absorption method. However, the signals received from radiation detectors contain a significant stochastic noise, which makes them difficult to analyse. The article describes four methods of noise reduction in cross-correlation measurements of water-air...
-
Reducing the Uncertainty of the Moving Object Location Measurement with the Method of Quasi-Multiple Measurement in GNSS Technology in Symmetrical Arrangement
Publikacja -
Estimating the uncertainty of the liquid mass flow using the orifice plate
PublikacjaThe article presents estimation of measurement uncertainty of a liquid mass flow using the orifice plate. This subject is essential because of the widespread use of this type of flow meters, which renders not only the quantitative estimation but also qualitative results of this type so those measurements are important. To achieve this goal, the authors of the paper propose to use the theory of uncertainty. The article shows the...
-
Investigation of Liquid–Gas Flow in a Horizontal Pipeline Using Gamma-Ray Technique and Modified Cross-Correlation
PublikacjaThis article presents the application of the radioisotope absorption method in the study of two-phase water–air flow in a horizontal pipe. The measurement principle and the test stand are briefly described. The main part of the article presents the signal analysis methods applied to data obtained from scintillation detectors. Because these signals are mostly stochastic waveforms, they were analyzed statistically using the cross-correlation...
-
Accurate Lightweight Calibration Methods for Mobile Low-Cost Particulate Matter Sensors
PublikacjaMonitoring air pollution is a critical step towards improving public health, particularly when it comes to identifying the primary air pollutants that can have an impact on human health. Among these pollutants, particulate matter (PM) with a diameter of up to 2.5 μ m (or PM2.5) is of particular concern, making it important to continuously and accurately monitor pollution related to PM. The emergence of mobile low-cost PM sensors...
-
USE OF LANGMUIR PROBE IN DIESEL ENGINE DIAGNOSTIC RESEARCH Part I MEASUREMENT TECHNOLOGY. - Part 1 : MEASUREMENT TECHNOLOGY
PublikacjaIn the paper, the basic assumptions of diesel engine cylinder system's diagnosing method, based on observation of emerging and moving electric charges of ionized gas in the combustion workspaces, using Langmuir's probe. In the first part of the paper, only the technology of the measurement and results of the preliminary diagnostic tests of laboratory engine Farymann Diesel D10 were presented. The primary purpose of the research...
-
Behavioral antecedents of coopetition: A synthesis and measurement scale
Publikacja -
Current measurement and analysis for induction motor diagnostics
PublikacjaPrzedstawiono sposób diagnozowania łożysk tocznych w silnikach indukcyjnych z wykorzystaniem pomiarów i analizy prądu zasilającego silnik. Zaprezentowano metodę pomiarową i opracowania danych diagnostycznych. Uzyskano zgodność częstotliwości składowych widma prądu otrzymanych z badań teoretycznych i eksperymentalnych.Podano wyniki badań łożysk o róznych uszkodzeniach i prawdopodobieństwa poprawnych diagnoz.
-
Circular saw blade dynamics - the measurement method
PublikacjaW pracy przedstawiono przyczyny i efekty zmiany położenia ostrzy piły tarczowej w układzie przecinania. Przedstawiony sposób pomiaru dynamiki piły tarczowej umożliwia określenie przyczyn drgań, co stanowi podstawę skutecznej ich minimalizacji.
-
Measurement of the muon stopping power in lead tungstate
Publikacja -
Optical Fibre, Local Measurement Systems For Ships
Publikacja -
Tire/road noise - generation, measurement, and abatement
PublikacjaPodano określenia i definicje dotyczące hałasu opon samochodowych. Omówiono mechanizmy generowania tego hałasu oraz zasady modelowania. Przedstawiono metody pomiaru hałasu opon oraz stosowane systemy pomiarowe. Podano normy dotyczące hałasu opon. Omówiono wpływ opony i nawierzchni na hałas generowany przez toczące się koło ogumione. Zaprezentowano koła kompozytowe oraz opony z bieżnikiem poroelastycznym generujące niski poziom...
-
Using argument structures to create a measurement plan
PublikacjaWhile planning an experiment the same question always arises: What are the goals of the experiment and which measurements are needed to demonstrate that the goals have been achieved? Deciding about the extent of raw data to be collected, the metrics to be constructed on those data and the interpretation of the metrics with respect to the assumed goals is by no means a trivial task. In this paper we show how a well known Gal-Question-Metrics...
-
Spirometry measurement model - the diagnostic purpose support
Publikacjathe paper presents a new model of respiratory mechanism based on the spirometry measurements. the spirometry test assesses the efficiency of the lung ventilation. the respiratory system functioning is based on the ventilation mechanism. thus the quality of the lung depends on the quality of lung ventilation. modelling of the respiratory system supports a diagnostic process. the model parameter estimates are obtained on the basis...
-
Impulse measurement accuracy of transmission line earthings
PublikacjaLinie przesyłowe elektroenergetyczne są wyposażone w przewody odgromowe łączące wierzchołki konstrukcji poszczególnych słupów. Zastosowana metoda pomiarów z użyciem udarów prądowych pozwala ocenić rezystancę uziemienia bez odłączania przewodów uziemiających od konstrukcji słupa. W pracy zamieszczono wyniki symulacji komputerowych i pomiarów rzeczywistych uziomów wskazujące, że wpływ równoległego połączenia uziemień całej linii...
-
Continuous‐Frequency Method of Measurement of Electrode Impedance
Publikacja -
The measurement of conformational stability of proteins adsorbed on siloxanes
Publikacja -
Measurement accuracy of the system to control the microwave heating.
PublikacjaPrzedstawiono skrótowo zasadę pracy i konstrukcję systemu do badań naukowych procesów grzania mikrofalowego. Wyprowadzono wyrażenie opisujące wartość średniokwadratową błędu pomiaru energii mikrofalowej i przeanalizowano składowe błędu pomiaru powodowane przez rzeczywiście występujące w układzie pomiarowym parametry techniczne jego części mikrofalowej.
-
Continuous frequency method of measurement of electrode impedance.
PublikacjaPrzedstawione zostały matematyczne podstawy nowej metody pomiaru impedancji elektrodowej. Metoda wykorzystuje sygnał pobudzenia którego częstotliwość zmienia się liniowo w czasie. Amplituda sinusoidalnego niestacjonarnego pobudzenia jest stała. Zapis i analiza sygnału pobudzenia i odpowiedzi pozwalana wyznaczenie ciągłego widma impedancyjnego. Jednoczesna analiza czasowo częstotliwościowa wykonano została przy użyciu transformacji...
-
Detection of measurement noise in surface topography analysis
Publikacja -
A Stand for Measurement and Prediction of Scattering Properties of Diffusers
PublikacjaIn this paper we present a set of solutions which may be used for prototyping and simulation of acoustic scattering devices. A system proposed is capable of measuring sound field. Also a way to use an open source solution for simulation of scattering phenomena occurring in proximity of acoustic diffusers is shown. The result of our work are measurement procedure and a prototype of the simulation script based on FEniCS - an open source...
-
Using A Particular Sampling Method for Impedance Measurement
PublikacjaThe paper presents an impedance measurement method using a particular sampling method which is an alternative to DFT calculation. The method uses a sine excitation signal and sampling response signals proportional to current flowing through and voltage across the measured impedance. The object impedance is calculated without using Fourier transform. The method was first evaluated in MATLAB by means of simulation. The method was...
-
Estimation of electrode contact in capacitive ECG measurement
PublikacjaIn the paper a method of electrode’s contact estimation in capacitive electrocardiogram (CECG) is presented. Proposed solution allows estimation of contact quality for each individual electrode. This enables construction of multi-electrode CECG systems, where electrode pairs can be selected on the basis of the individual electrode contact quality.
-
Impact of probability distribution on the uncertainty of resistance measurement
PublikacjaThe paper presents studies on the influence of probability distributions on the expanded uncertainty of the resistance measurement. Choosing the correct probability distribution is very important to estimate of measurement uncertainty. The paper presents the results of analysis of the resistance measurement uncertainty using the technical method of resistance: 100 G. The analysis of the uncertainty...
-
Remote current measurement with FPGA digital processing
PublikacjaThe work presents an implementation of a modular measurement and control systemthat controls variants of mains supply of 230V electrical equipment. The system allowsto supervise power consumption in the office electronic equipment. The system detectsthe instant of the reduced power consumption by a device and makes possible itsswitch-off in order to reduce energy cost. The current is measured with integratedcurrent/voltage converters....
-
Risk Analysis by a Probabilistic Model of the Measurement Process
PublikacjaThe aim of the article is presentation of the testing methodology and results of examination the probabilistic model of the measurement process. The case study concerns the determination of the risk of an incorrect decision in the assessment of the compliance of products by measurement. Measurand is characterized by the generalized Rayleigh distribution. The model of the meas-urement process was tested in parallel mode by six risk...
-
The Double Cognitive Bias of Mistakes: A Measurement Method
PublikacjaThere is no learning without mistakes. However, making mistakes among knowledge workers is s�ll seeing shameful. There is a clash between posi�ve a�tudes and beliefs regarding the power of gaining new (tacit) knowledge by ac�ng in new contexts and nega�ve a�tudes and beliefs toward accompanying mistakes that are sources of learning. These contradictory a�tudes create a bias that is doubled by the other shared solid belief...
-
Web Based Acoustic Noise Measurement System.
PublikacjaW referacie przedstawiono projekt multimedialnego systemu przeznaczonego do monitorowania zagrożeń hałasem środowiskowym. Nadrzędnym celem realizowanego projektu jest zwiększenie efektywności profilaktyki chorób słuchu. Opracowywany system umożliwia odbiór, przechowywanie danych, analizę i wizualizację wyników pomiarów hałasu pozyskanych od urządzeń pomiarowych za pośrednictwem Internetu. Przedstawiono również opracowanie miernika...
-
Determination of the Territorial Sea Baseline – Measurement Aspect
Publikacja -
Estimation of respiration rate using an accelerometer and thermal camera in eGlasses
PublikacjaRespiration rate is a very important vital sign. Different methods of respiration rate measurement or estimation have been developed. However, especially interesting are those that enable remote and unobtrusive monitoring. In this study, we investigated the use of smart glasses for the estimation of respiration rate especially useful for indoors applications. Two methods were analyzed. The first one is based on measurements of...
-
Assessment of image processing methods for the determination of propagation of squat-type defects in rails
PublikacjaWe demonstrate the idea of squat-type defect measurement in the rail and the concept of tracking of the defect development using the techniques of image acquisition and image processing as well as the methods of metric spaces. We introduce the concepts of a set diameter δ(A) and the metric ρ1, which come from the properties of plane figures, to compare and to observe the development of the defects. We characterize the feasibility...
-
How to define and measure informal employment in CEE countries - the case of Poland
PublikacjaThe study of informal employment is still associated with several obstacles, from the scope of definition, through measurement methods, to policy recommendations. This article aims to revise the existing methodological frames in order to point out how to improve the study of informal employment in CEE countries. The case of Poland serves to examine whether the common definitions and measurement methods are suitable for an inclusive...
-
Leakage Current Measurements of Surge Arresters
PublikacjaThe paper presents the methods of assessing the technical condition of varistor surge arresters used in laboratory tests and in operation—performed without disconnecting the arresters from the network. The analysis of the diagnostic methods was supplemented with the results of the measurements of the leakage current of arresters coming directly from their production and used in the power industry. Among the available methods of...
-
Third harmonic index as a diagnostic tool of high-voltage varistors
PublikacjaThe recommended methods for standard testing of high-voltage varistors demand application of high voltages and intensive currents that is inconvenient and needs extensive power consumption. These methods require metallization of the prepared ZnO structures that increases costs of testing. Another method of varistor quality and endurance evaluation by the third harmonic index measurement at relatively low voltage range has been...
-
The applicability of low-cost PM10 sensors for atmospheric air quality monitoring
PublikacjaDescribed in this work are the results of field tests carried out in the Tricity Agglomeration between 01 April 2018 and 30 June 2018 in order to evaluate the usefulness of low-cost PM10 sensors in atmospheric air quality monitoring. The results were juxtaposed with the results obtained using reference methods. The results were validated based on the measurement uncertainty as described in...
-
Electrochemical sensor for measurement of volatile organic compounds in air
PublikacjaPrzedstawiono rezultaty badań prototypowego czujnika do oznaczania mrówczanu etylu i formaldehydu w powietrzu. Określono czułość wskazań czujnika i jego granice oznaczalności wykorzystując jako techniki detekcyjne pulsową woltamperometrię różnicową (DPV) oraz woltamperometrię fali prostokątnej (SWV). Elektrodę roboczą i przeciwelektrodę stanowiły elektrody z Pt. Elektrolitem wewnętrznym była ciecz jonowa (chlorek 1-heksylo,3-metyloimidazolinowy)....
-
Noise measurement setups for fluctuations enhanced gas sensing
PublikacjaObserwacje zjawisk fluktuacyjnych w sensorach gazów pozwala zwiększyć czułość i selektywność detekcji gazów. Problemem jest budowa prostego i taniego systemu do obserwacji tych zjawisk. W artykule przedstawiono dwa systemy pozwalające na obserwacje szumów w rezystancyjnych sensorach gazów dostępnych na rynku i prototypowych, wykonanych z warstwy nanocząstek o zbliżonych wymiarach.
-
<title>Automatic measurement system for astronomical education</title>
Publikacja -
Digital measurement of frequency with linear interpolation in dynamic states
PublikacjaPrzedstawiono metody rejestracji częstotliwości sygnałów impulsowych. Zastosowanie interpolacji pozwala na uzyskanie wyniku dla dowolnej chwili. Opisano pracę w trybie on-line i off-line.
-
An analysis of a measurement probe for a high impedance spectroscopy analyzer
PublikacjaW artykule przedstawiono sondę będącą obwodem wejściowym analizatora do spektroskopii wysokoimpedancyjnej. Sonda umożliwia pomiar impedancji jednym zaciskiem uziemnionej w zakresie od 100ohm do 100Gohm. Sonda umożliwia wydzielenie dwóch sygnałów proporcjonalnych do prądu i napięcia na impedancji mierzonej w szerokim zakresie częstotliwosci od 100uHz do 100MHz.Przeprowadzono analizę sondy w której uwzględniono najważniejsze czynniki...
-
Position and velocity measurement using incremental encoder and microcontroller.
PublikacjaThere is presented measurement of position and velocity using Atmel's microcontroller ATTiny2313 with 20 MHz clock and encoder with 1024 pulses per revolution. This configuration allows measuring maximum speed 48800 rpm with 1x accuracy, 20200 rpm with 2x accuracy and 9400 rpm with 4x accuracy (quadrature). Position is measured with resolution of 0.352', 0.176' and 0.088' for 1x, 2x, 4x accuracy respectively. Algorithms of position...
-
Fast impedance measurement method using Laplace transformation
PublikacjaArtykuł przedstawia metodę pomiaru impedancji wykorzystującą rzeczywisty uskok jednostkowy step jako sygnał pobudzenia i transformację Laplace jako narzędzie analizy sygnału odpowiedzi testowanego obiektu. Metoda jest dedykowana do badania różnych obiektów technicznych (np. powłok antykorozyjnych, czujników gazu, ceramik, tkanek biologicznych itp.) gdy czas pomiaru nie może być długi. Przedstawiona metoda jest znana ale niezbyt...
-
New concept of a measurement probe for high impedance spectrocopy
PublikacjaArtykuł przedstawia nową koncepcję sondy pomiarowej służącej jako obwód wejściowy analizatora do spektroskopii wysokoimpedancyjnej. Dzięki wykorzystaniu przetwornika prąd na napięcie uzyskano najmniejszy możliwy wpływ pojemności kabli dołączających mierzony obiekt na wynik pomiaru. Przeprowadzono analizę sondy biorąc pod uwagę najważniejsze parametry wpływające na dokładność pomiaru: pojemności pasożytnicze oraz rzeczywiste parametry...
-
An analysis of a measurement probe for a high impedance spectroscopy analyzer
PublikacjaW artykule przedstawiono sondę będącą obwodem wejściowym analizatora do spektroskopii wysokoimpedancyjnej. Sonda umożliwia pomiar impedancji jednym zaciskiem uziemnionej w zakresie od 100ohm do 100Gohm. Sonda umożliwia wydzielenie dwóch sygnałów proporcjonalnych do prądu i napięcia na impedancji mierzonej w szerokim zakresie częstotliwości od 100uHz do 100MHz.Przeprowadzono analizę sondy w której uwzględniono najważniejsze czynniki...
-
Mobile wireless measurement system for potatoes storage management
PublikacjaThe paper discusses the idea and the design of a remote control system for a storage management of agricultural products which temperature may rise in a result of biological processes during the storage. Exemplary potatoes storehouse is discussed as an application of the automation system. Because of existing buildings and infrastructure in the farm, wireless data transfer system has been proposed for both sensors to data acquisition...
-
A prototype of electrochemical sensor for measurement of carbonyl compounds in air
PublikacjaThe paper presents the results of investigation on a prototype sensor for measurement of benzaldehyde and formaldehyde in air. Sensitivity, limit of quantification and coefficient of selectivity of the sensor have been determined as a function of membrane thickness and electrode type using square wave voltammetry (SWV) technique. The working and counter electrodes were made of platinum and gold. Ionic liquids 1-hexyl, 3-methylimidazolium...