Filtry
wszystkich: 436
wybranych: 365
Wyniki wyszukiwania dla: CABLE-STAYED BRIDGE
-
Effect of solar radiation on current-carrying capacity of PVC-insulated power cables – the numerical point of view
PublikacjaPower cables are usually buried in the soil, which results in their relatively high current-carrying capacity. However, there are cases in which the starting/final section of a cable line runs along a pole of an overhead power line. Power cables can be directly exposed to solar radiation then, and this negatively influences their current-carrying capacity as well as estimated life of the cables’ insulation. An analysis of thermal...
-
Composite sandwich footbridge - measured dynamic response vs. FEA
PublikacjaThe paper describes a process of in situ dynamic tests of a composite sandwich footbridge before its accepta-tion for exploitation in real traffic conditions. It is only a part of a big research task that includes design, manufacture and introduce practical application of the bridge. The in situ measured natural modes and fre-quencies are compared with numerically determined ones. Finite element analysis is established to estimate...
-
Ampacity of power cables exposed to solar radiation – recommendations of standards vs. CFD simulations
PublikacjaThe aim of the paper is to evaluate the ampacity of a low-voltage single power cable according to: 1) recommendations of the standard IEC 60287, 2) a Computational Fluid Dynamics method, implemented in Ansys software; and comparison of the results obtained for these two cases. Moreover, limitations of recommendations of the above mentioned standard are indicated.
-
Arch bridges under test loadings
PublikacjaThis paper illustrates experience in arch bridges test loadings of the research team of Department of Structural Mechanics and Bridge Structures from the Gdansk University of Technology. The presented calculations results constist the analysis of spatial construction schemes made using the finite elements method (FEM) and its comparison to the field studies. Arch bridges with the longest spans, visualisation of the computational...
-
Single-phase power electronics transformer with active functions for smart grid
PublikacjaThis paper presents the control of one cell of a modular single-phase power electronics transformer with active functions for meeting the smart grid concept. In this way, the converter could be used not only as a conventional transformer but also for grid such as reactive power, harmonic elimination and energy storage. The topology of the cell is composed by a bidirectional converter with three stages: a half bridge in the input...
-
Short and Long Term Measurements in Assessment of FRP Composite Footbridge Behavior
PublikacjaThe paper presents application of different sensors for the purpose of short and long term measurements, as well as a structural health monitoring (SHM) system to assess the behavior of a novel fiber reinforced plastics (FRP) composite footbridge. The aim is to present a thorough and concise description of these sensors networks and results gathered with their aid during in situ measurement of strains, displacements, and vibrations,...
-
Load test of new European record holder in span length among extradosed type bridges
PublikacjaThe article presents acceptance load tests of a newly built extradosed MS-3 bridge located along the national road DK-16 near Ostróda (Poland). The structure features significant dimension in European reference scale. It is a new record holder in span length regarding this distinct bridge category. Its length ranges 206 m. Static and dynamic load tests were performed here. The program was extended by entire structural laser scanning...
-
Improving the procedure of probabilistic load testing design of typical bridges based on structural response similarities
PublikacjaThis paper concerns load testing of typical bridge structures performed prior to operation. In-situ tests of a two-span post-tensioned bridge loaded with three vehicles of 38-ton mass each formed the input of this study. On the basis of the results of these measurements, an advanced FEM model of the structure was developed for which the sensitivity analysis was performed for chosen uncertainty sources. Three uncorrelated random...
-
Parametric analysis of Istanbul's Ring Road viaduct for three levels of seismic load
PublikacjaThe paper presents a numerical analysis of the Istanbul's ring road viaduct that is currently under construction within the Northern Marmara Highway project. The structure, due to its location on seismic prone areas is exposed to seismic loads of different magnitude and different return periods. The study is fo-cused on concrete bridge supports that are design to work in nonlinear range. The study, conducted in SOFISTIK environment,...
-
Earthquake-Induced Structural Pounding
PublikacjaEarthquake-induced structural pounding between insufficiently separated build-ings, or bridge segments, has been repeatedly observed during ground motions. The reports after earthquakes indicate that it may lead to some local damage in the case of moderate seismic events or may result in considerable destruction or even collapse of colliding structures during severe ground motions. Pounding in build-ings is usually caused by the...
-
Application of probabilistic tools to extend load test design of bridges prior to opening
PublikacjaLoad tests of bridges are widely performed in a large number of countries. Deterministic comparison of measurement results to the theoretical, FEM (finite element method)-based outcomes with possible further calibration is mostly applied. Sometimes, the data collected in the tests are also used to calibrate the reliability factors of bridge structures or their components. This work proposes to complement the stage of the load test...
-
Impact of thermal backfill parameters on current-carrying capacity of power cables installed in the ground
PublikacjaProper design of power installations with the participation of power cables buried in homogeneous and thermally well-conductive ground does not constitute a major problem. The situation changes when the ground is non-homogeneous and thermally low-conductive. In such a situation, a thermal backfill near the cables is commonly used. The optimization of thermal backfill parameters to achieve the highest possible current-carrying capacity...
-
Design and numerical testing of 5-box gfrp shell footbridge
PublikacjaThe paper formulates new design conditions for composite footbridges, taking into account the material and structural specificity of these objects, i.e. the strength condition, the serviceability condition and the frequency condition. A GFRP composite footbridge labelled with CFB2 code has been designed, with the original superstructure in the form of an opened-closed 5-box girder. The foot and cycle track bridge is simply supported,...
-
OCENA WŁAŚCIWOŚCI STALI STOSOWANEJ W STARYCH OBIEKTACH KOLEJOWYCH
PublikacjaThe scope of the paper is to give an introduction to the assessment subject matter of steel properties used in old railway bridges. The mechanical and chemical properties of construction steel extracted from old steel bridges are generally investigated by tensile tests, impact tests through the Charpy pendulum impact V-notch, and an optical emission spectrometer. Besides descriptions of the tests, the chosen chemical and mechanical...
-
Parametric analysis of Istanbul's Ring Road viaduct for three levels of seismic load
PublikacjaThe paper presents a parametric analysis of the Istanbul's ring road viaduct that is currently under construction within the Northern Marmara Highway project. The structure, due to its location on seismic prone areas is exposed to seismic loads of different strengths and different return periods. The study is focused on concrete bridge supports that are design to work in nonlinear range. The parametric study, conducted in MATLAB...
-
KOMPOZYTOWY MOST PIESZO - ROWEROWY
PublikacjaPaper presents the composite foot and cycle bridge developed in FOBRIDGE grant cofinanced by The National Centre for Research and Development and realized by consortium of Gdansk University of Technology (leader), Military University of Technology in Warsaw and ROMA Sp. z o.o. in Toruń. The purpose of the grant was to design a shell type single span foot and cycle bridge made of composite materials, with the assumption of manufacturing...
-
Excitation-independent constant conductance isfet driver
PublikacjaA new constant conductance driver for ISFETs sensors has been developed. The proposed circuit maintains the sensor operating point at constant drain-source conductance. The combination of a simple, self-balancing resistance bridge and the subtraction half (or similar fraction) of source-drain voltage from the gate-source voltage provides the independence of output signal from current and voltage drivers instability. The use of...
-
Structural Health Monitoring of Composite Shell Footbridge for Its Design Validation
PublikacjaThe paper presents the structural health monitoring system of the composite bridge for pedestrians and cyclists. The footbridge was designed and manufactured within the FOBRIDGE project. It is the first bridge in the world, which is classified as a consistent single element structural girder, made of sandwich shells, entirely produced in a single cycle. The developed structural health monitoring system, supported design process,...
-
EMI mitigation of GaN power inverter leg by local shielding techniques
PublikacjaThis paper presents local shielding techniques applied to a half-bridge inverter leg with the aim to reduce the common mode (CM) current noise at converter’s DC input. The research study is conducted for 650V Enhancement mode Gallium Nitride (GaN) power transistor switches. Main contributors of parasitic capacitances referred to the inverter-leg middle point node are identified. Then, shielding solutions are proposed to reduce...
-
Problems of construction projects regarding historic road bridges
PublikacjaThe paper describe the comparison of different approaches to reconstruction and the problems in the selection of implementation for a historic bridge over the Vistula River in Tczew. A compromise reconstruction is shown, taking technical, historical and aesthetic aspects into account, as well as needs of the local community.
-
Identyfikacja parametrów dynamicznych want mostu Rędzińskiego we Wrocławiu
Publikacjathe paper presents results of dynamic analysis conducted on stay-cables of rędziński bridge in wrocław. identified in situ dynamic parameters (natural frequency and logarithmic decrement damping ratio) of selected stays were and compared to the values featured in the project.
-
Antimicrobial Activity of Chimera Peptides Composed of Human Neutrophil Peptide 1 (HNP-1) Truncated Analogues and Bovine Lactoferrampin
PublikacjaThree chimera peptides composed of bovine lactoferrampin and the analogue of truncated human neutrophil peptide 1 were synthesized by the solid-phase method. In two compounds peptide chains were connected via isopeptide bond, whereas in the third one disulfide bridge served as a linker. All three chimeras displayed significantly higher antimicrobial activity than the constituent peptides as well as their equimolar mixtures. The...
-
Zabezpieczenia antykorozyjne stalowych barierek ochronnych na obiektach mostowych w ujęciu kosztów cyklu ich życia
PublikacjaThe article presents the Life Cycle Costs analysis of steel safety barriers operated in road lane conditions, located on a selected bridge structure. Three corrosion protection systems were proposed, analyzing them in terms of the cost of initial and planned outlays related to maintenance. Based on the LCC analysis for three options, taking into account the 25-year lifetime of the barriers, the optimal solutionwas indicated, i.e....
-
Multipoint Ultrasonic Diagnostics System of Prestressed T-Beams
PublikacjaThis paper is devoted to the application of ultrasonic wave propagation phenomena for the diagnostics of prestressed, concrete, bridge T-beams. A multi-point damage detection system is studied with use of numerically obtained data. The system is designed to detect the presence of the material discontinuities as well as their location.
-
Zastosowanie specjalnego uziemienia żył powrotnych w liniach kablowych SN
PublikacjaW artykule porównano metody uziemiania żył powrotnych kabli średniego napięcia. Głównym kryterium oceny poszczególnych rozwiązań było ograniczenie strat w przesyle energii elektrycznej oraz zapewnienie ochrony przeciwprzepięciowej osłon kabli. Na podstawie symulacji kabli zamodelowanych w programie CYMCAP i otrzymanych wyników obciążalności prądowej i strat w linii zaprezentowano metodę krzyżowania żył powrotnych (CB – cross-bonding...
-
Modern control strategy of bidirectional DAB converter with consideration of control nonlinearity
PublikacjaThis paper focuses on the control strategy for modern universal bidirectional Dual Active Bridge (DAB) converters for microgrid systems. An analysis of the converter equations was carried out, and typical problems related to the influence of dead time on the system operation were discussed. A closed control loop was developed, then tested by simulation and on a laboratory stand.
-
Study on applicability of two modal identification techniques in irrelevant cases
PublikacjaStudy on applicability of two modal identification techniques in irrelevant cases is made in this paper. The following techniques are considered: Peak Picking based on correlation analysis (PP-CA), dedicated for ambient vibrations and Eigensystem Realization Algorithm (ERA), formulated for free decay vibrations investigation. Irrelevant cases are found when analyzed signals are different than recommended to a given technique. The...
-
Experimental study on the behaviour of steel columns under seismic-induced axial impact load
PublikacjaIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. Therefore, the aim of this paper is to investigate experimentally the behaviour of columns under bending (observed...
-
Działalność w obszarze grantów realizowana przez Katedrę Sieci Teleinformacyjnych
PublikacjaPrzedstawiono działalność Katedry Sieci Teleinformacyjnych PG WETI w obszarze grantów finansowanych przez instytucje centralne, przy czym główny nacisk położono na scharakteryzowanie aktualnie realizowanych projektów. Opisano dwa projekty finansowane przez NCBiR. Pierwszy dotyczy koncepcji oraz implementacji integracji informacji w rozproszonych elementach systemu wymiany danych Straży Granicznej, natomiast drugi strumieniowej...
-
The use of fibre-reinforced polymers (FRP) in bridges as a favourable solution for the environment
PublikacjaThe purpose of this article is to show the modern engineering, in which sustainability and taking care of ecology play a significant role. The authors are focused on FRP composite materials and their applications in civil engineering. Case studies showing renovation and design of new bridges with the use of FRP are presented and discussed to clarify benefits, which this solution provides. Main advantages of FRP materials in comparison...
-
Framework for Structural Health Monitoring of Steel Bridges by Computer Vision
PublikacjaThe monitoring of a structural condition of steel bridges is an important issue. Good condition of infrastructure facilities ensures the safety and economic well-being of society. At the same time, due to the continuous development, rising wealth of the society and socio-economic integration of countries, the number of infrastructural objects is growing. Therefore, there is a need to introduce an easy-to-use and relatively low-cost...
-
WERYFIKACJA KONCEPCJI PRZEGUBÓW PLASTYCZNYCH PROJEKTOWANYCH NA ODZIAŁYWANIA SEJSMICZNE WIADUKTU V6 OBWODNICY ISTAMBUŁU
PublikacjaW pracy zawarto wyniki analiz betonowego wiaduktu V6 budowanego w ciągu obwodnicy Istambułu w Turcji realizowanego w ramach projektu Northern Marmara Highway. Przeprawę stanowią dwie niezależne nitki o skrzynkowym przekroju poprzecznym i szerokości 22,00 m. Schemat statyczny obiektu to belka dziewięcioprzęsłowa o długości całkowitej 446,86 m oparta na podporach słupowych o zmiennej sztywności (rys.1) i wysokościach zmieniających...
-
Secured wired BPL voice transmission system
PublikacjaDesigning a secured voice transmission system is not a trivial task. Wired media, thanks to their reliability and resistance to mechanical damage, seem an ideal solution. The BPL (Broadband over Power Line) cable is resistant to electricity stoppage and partial damage of phase conductors, ensuring continuity of transmission in case of an emergency. It seems an appropriate tool for delivering critical data, mostly clear and understandable...
-
Gate Driver with Overcurrent Protection Circuit for GaN Transistors
PublikacjaThe improvement of the gate driver for GaN transistor is presented in this paper. The proposed topology contains the overcurrent protectionwith the two-stage turning off and independent control of turn on and off time of the GaN transistor. The operation of driver and its application in thehalf-bridge converter are described using both simulation and prototype measurements. The overcurrent protection was tested in Double Pulse...
-
Test loadings of arch bridges
PublikacjaIn Poland an appreciable developement of bridge building can be seen in recent years. Arch structures are more and more common, because of the original geometrical and aesthetical form, aside with explicit structural system. Paper concerns the applied computational conceptions and researches on an example of two arch bridges. The goal of the studies is to check the correctness of the real construction work and design assumptions,...
-
Kompozytowy most dla pieszych. Badania doświadczalne i przygotowanie do projektowania
PublikacjaDysertacja powstała w ramach grantu badawczego NCBiR, pt. „Opracowanie kompozytowych przęseł mostów dla pieszych do zastosowania nad drogami GP”, nr PBS1/B2/6/2013. Głównym celem pracy było wsparcie procesu projektowania kompozytowego mostu pieszo-rowerowego. Zakres pracy obejmuje badania doświadczalne elementów kompozytowych GFRP, walidację modeli obliczeniowych oraz wykorzystanie aparatu analizy wrażliwości do procesu projektowego....
-
Comparison of calculated and measured thermal stresses in asphalt concrete
PublikacjaThe paper presents the comparison of calculated and measured thermal stresses induced in restrained asphalt concrete specimens by cooling. Thermal stresses were measured in the Thermal Stress Restrained Specimen Test. The calculations of thermal stresses were performed with the use of a theoretical formula based on the temperature dependent stiffness modulus. The novel approach applied in this paper was that the stiffness modulus...
-
Equivalent axle load factors for design of rigid pavements derived from fatigue criteria
PublikacjaArtykuł przedstawia określenie współczynników równoważności osi dla nawierzchni sztywnych na podstawie kryteriów zmęczeniowych stosowanych w mechanistyczno-empirycznej metodzie projektowania nawierzchni drogowych. Przedstawiono kryteria zmęczeniowe z wybranych metod projektowania i analizy nawierzchni sztywnych. Kryteria te zostały użyte do wyprowadzenia wzorów do obliczania współczynników równoważności obciążenia osi. Stwierdzono,...
-
The Impact of Long-Time Chemical Bonds in Mineral-Cement-Emulsion Mixtures on Stiffness Modulus
PublikacjaDeep cold in-place recycling is the most popular method of reuse of existing old and deteriorated asphalt layers of road pavements. In Poland, in most cases, the Mineral-Cement-Emulsion mixture technology is used, but there are also applications combining foamed bitumen and cement. Mineral-Cement-Emulsion mixtures contain two different binding agents – cement as well as asphalt from the asphalt emulsion. Asphalt creates asphalt...
-
Modelling of joining route segments of differential curvature
PublikacjaThe paper presents a new general method of modelling route segments curvature using differential equations. The method enables joining of route segments of different curvature. Transitional curves of linear and nonlinear curvatures have been identified in the case of joining two circular arcs by S-shaped and C-oval transitions. The obtained S-shaped curves have been compared to the cubic C-Bezier curves and to the Pythagorean hodograph...
-
Low-Temperature Requirements for Bitumen in Central East European Road Construction
PublikacjaThe paper presents the proposition of special assessment of lowtemperature requirements for bitumens in the region of Central and Eastern Europe where there is a moderate transitional area from sea to the continental type of climate. The results of the research program conducted on the road neat bitumens, Styrene-Butadiene-Styrene polymer and polymer-rubber modified bitumen, and multigrade bitumen types were presented and discussed....
-
Does the Use of Cell Phones and Headphones at the Signalised Pedestrian Crossings Increase the Risk of Accident?
PublikacjaReduction of the number of fatalities among pedestrians remains a topical issue in Poland. For many years, this percentage has remained at around 30% of all those who were killed on the road. At the same time, there is an increase in the use of electronic devices by pedestrians and cyclists that may affect their perception when crossing the road. This can lead to traffic accidents. In order to investigate the problem, field studies...
-
MONITORING SYSTEM OF THE ROAD EMBANKMENT
PublikacjaThe paper presents the analysis of the monitoring system of the embankment supported on concrete columns and overlaid by a load transfer platform with the embedded steel grid. This field investigation was to study the complex interaction among the columns, the load transfer platform layer, and steel grid via in situ measurements during erection and live loading of the embankment. The study was focused on the behaviour of steel...
-
Inception and Propagation of Electrical Trees in the Presence of Space Charge in HVAC Extruded Cables
PublikacjaThis paper presents the space charge impact on the inception and propagation of electrical trees in cross-linked polyethylene (XLPE) insulation via simulations and experimentation. A 3D finite element analysis (FEA)-based modeling is proposed to simulate electrical trees via a needle embedded on the XLPE insulation. The proposed FEA model demonstrates the influence of the space charge magnitude and polarity on the initiation of...
-
Analysis of AC/DC/DC Converter Modules for Direct Current Fast-Charging Applications
PublikacjaThe paper is a comprehensive laboratory comparison study of two galvanic isolated solution off-board battery chargers: (1) Si-based cost-effective case, and (2) SiC-bidirectional ready for vehicle to grid concept case. All circuits are modular, and in both cases the DC/DC converter can be replaced according to the end user requirements (the coupled transformer remains the same and is constructed based on 12xC100 cores to avoid...
-
O modelowaniu numerycznym dźwigarów zespolonych
PublikacjaThe paper is a general review of theoretical problems and corresponding numerical procedures actually available in commercial engineering software. Several possibilities of numerical simulation for composite girders are presented. Effectivity of meshing is showed on the simple example. Finally several examples of structural numeric models for real bridges are included. In the author's opinion, presented available procedures for...
-
Die neue Straßenbrücke in Toruń (Thorn) – Teil 2 – Nachweise
PublikacjaAls Fortsetzung von Teil 1, der über den Entwurf und den Bau der neuen, die Weichsel querenden Straßenbrücken in Toruń (deutsch: Thorn) berichtet, geht es im Folgenden um die theoretischen und experimentalen Nachweisen zum Montageprozess und zu Probebelastungen. Somit eine umfassende Beurteilung der beschriebenen , herausragenden Ingenieursleistung gegeben.
-
Przyczółki mostowe z konstrukcją odciążającą z gruntu zbrojonego geosyntetykami
PublikacjaPrzegląd najważniejszych cech geotekstyliów i wyrobów pokrewnych, zastosowanych do budowy bloków odciążających ze szczególnym uwzględnieniem ich wytrzymałości długo i krótkookresowej oraz reologii. Określenie obciążeń działających na konstrukcję gruntową współpracującą z przyczółkiem; obciążenia normowe i rzeczywiste. Obliczenia konstrukcji z gruntu zbrojonego współpracującej z przyczółkiem
-
OCENA NOŚNOŚCI STAREGO MOSTU ŁUKOWEGO W JAGODNIKU
PublikacjaArtykuł opisuje przeprowadzoną analizę statyczno-wytrzymałościowa 95-letniego betonowego mostu łukowego zlokalizowanego w Jagodniku w północnej Polsce. Trwałość i wytrzymałość starego betonu są określane na podstawie wybranych właściwości mechanicznych, fizycznych i chemicznych. Program badań laboratoryjnych składał się z następującego zestawu badań: pomiary głębokości strefy skarbonatyzowanej i gęstości w stanie suchym, badania...
-
Arch footbridge over Warta river in Wronki - design and construction
PublikacjaThe paper presents the concept of dynamic redesign of lively footbridge. The goal was to reduce probable dynamic excitation and change detailed structural concept. After the complex study the new design was created. In effect completely new static and dynamic properties were reached. Static and dynamic assumptions are explainde. General information, photos and drawings are presented. The final price of the project amounted to 1.25...