Filtry
wszystkich: 691
wybranych: 626
Wyniki wyszukiwania dla: ROAD SAFETY MANAGEMENT AND MODELING
-
Temperature influence on tyre/road noise of selected tyres
PublikacjaAir and road temperatures substantially affect road vehicle noise emission. The temperature influence on tyre/road noise depends mainly on tyre-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tyres. The correction procedures for temperature effect are still under consideration and preparation. Tyre/road noise measurements using CPX method were performed...
-
Low noise poroelastic road pavements based on modified asphalt binder
PublikacjaTire/road noise is one of the most important environmental problems related to road traffic. As the most effective way to fight noise is reduction of sound emission from the source, a lot of work is being done to improve tire and road surfaces construction. This paper describes the first “road” results obtained within the SEPOR project, which is focused on developing a low noise poroelastic road surface based on bituminous binder....
-
Concrete versus green corridors in road planning. Gdansk case
PublikacjaThe aim of an article is to present the threats which may be caused by the construction of the transit road inside the city structure, and some mitigation measures aiming to eliminate or minimize environmental and landscape damages and social problems. Theoretical guidelines and conclusions will be followed by the example illustrating the problem. As an answer, some guidelines enabling sustainable road planning will be presented....
-
Economical methods for measuring road surface roughness
PublikacjaTwo low-cost methods of estimating the road surface condition are presented in the paper, the first one based on the use of accelerometers and the other on the analysis of images acquired from cameras installed in a vehicle. In the first method, miniature positioning and accelerometer sensors are used for evaluation of the road surface roughness. The device designed for installation in vehicles is composed of a GPS receiver and...
-
Times Series Analysis Of Road Safety Trends At The Regional Level In Poland
PublikacjaThe paper presents possibility of applying a structural times series modeling with explanatory and intervention variables as a tool capable for explaining the changes in the monthly number of fatalities and seriously injured in traffic accidents. The analysis covers regional level and takes into consideration traffic accidents data of two regions: Pomorskie and Warmia-Mazury. In addition short-term forecasts for the two regions...
-
GAMBIT's position within the European Union's III Road Safety Plan
PublikacjaOtwarcie Seminarium GAMBIT 2006, poświęcone wnioskom z dotychczasowych działań oraz planom na przyszłość, zawartym w najnowszym Krajowym Programie GAMBIT 2005. Prace nad nim rozpoczęto w sierpniu 2004, czyli tuż po wejściu Polski do Unii Europejskiej. W kwietniu 2005 Rada Ministrów przyjęła GAMBIT 2005 jako program dla Polski na lata 2005-2013, skonstruowany zgodnie z metodyką opracowaną dla tych krajów UE-25, których poziom zagrożenia...
-
Acoustic evaluation of road surfaces using different Close Proximity testing devices
PublikacjaAccording to the valid standard, Close Proximity (CPX) method intends to evaluate the influence of road surfaces on traffic noise. Measurements may be carried out with the use of a self-powered vehicle or a special test trailer equipped with testing tyre towed by another vehicle. Two different testing devices took part in the research organized in Poland in order to determine the ranking of road surfaces in terms of acoustic parameters....
-
Poroelastic Material for Urban Roads Wearing Courses
PublikacjaConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
TIRE/ROAD NOISE AND TIRE ROLLING RESISTANCE ON PROTOTYPE PERS SURFACE
PublikacjaPoroelastic road surfaces are characterized by low noise of tires running on them.Road pavements of this type are promising solution to problems related to traffic noise in cities and on rural roads. Some technical problems still have to be solved, in particular regarding durability and skid resistance on wet surface. Ongoing and planned works are to contribute to create a quiet, durable and safe road surface, which will become...
-
Poroelastic Material for Urban Roads Wearing Courses
PublikacjaConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublikacjaThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
A pin-on-disc study of airborne wear particle emissions from studded tyre on concrete road contacts
PublikacjaStudded tyres wear surfaces of winter roads, generating inhalable airborne particles. In this study, four concrete road materials and two stud geometries were investigated in terms of wear, road material hardness and airborne particle concentration. The sliding contact between studded tyres and road materials was studied using a pin-on-disc machine in a clean chamber. The results show that the normal load and the stud size have...
-
Tire/Road Noise On Poroelastic Road Surfaces - Results Of Laboratory Measurements
PublikacjaTire/road noise is the most important part of traffic noise for medium and high speed driving both in the case of passenger cars and trucks. The potential to make modification of tires that significantly reduce tire/road noise in nearly over, at least for conventional tires so the only promising action is to improve road pavements. One of the innovative solutions is poroelastic road pavement (PERS) that reduces airflow related...
-
Risks related to car fire on innovative Poroelastic Road Surfaces-PERS
PublikacjaTo reduce tyre/road noise, the concept of poroelastic road surfaces (PERS) was invented. PERS is a road surface material that is porous, and at the same time, it is flexible because of the substantial amount of rubber granulate content (from 20% to 85%). The rubber and stone particles are bound by polyurethane resin instead of bitumen. It was feared that in case of fire, because of the high content of rubber and polyurethane, there...
-
Layers of protection analysis in teh context of functional safety management
Publikacja -
Human and organizational factors in risk analysis and safety management of azardous
PublikacjaArtykuł porusza aktualne kwestie dyskutowane podczas warsztatów na temat czynników ludzkich i organizacyjnych w analizie ryzyka i zarządzaniu bezpieczeństwem instalacji przemysłowych wysokiego ryzyka. Zauważa się rosnącą świadomość, że eksploatacja złożonego systemu wyposażonego w środki bezpieczeństwa oraz redundancyjne układy zabezpieczeń i sterowania, zawierające jednostki programowalne, może spowodować większe uzależnienie...
-
ANALYSIS OF CLIMATIC ZONES IN POLAND WITH REGARD TO ASPHALT PERFORMANCE GRADING
PublikacjaTowards the end of the last century a new system of bitumen grading was developed and implemented as part of the American Strategic Highway Research Program (SHRP). Its aim was to better adjust the testing methods and requirements for road bitumens to the actual conditions in which those bitumens serve in road pavements. Currently in Poland, similarly as in the other EU countries, road bitumens are tested and classified with regard...
-
HOW EFFICIENT IS NOISE LABELING OF TIRES?
PublikacjaSince 2012 all new tires in Europe must be labeled. The label contains general information about tire performance concerning rolling resistance (that corresponds to fuel economy), noise emission and wet grip (only for passenger car tires). Measurements of noise performance of tires must be performed according to the Annex 3 of the Regulation No 117 of the Economic Commission for Europe of the United Nations. The regulation specifies...
-
Detection of Water on Road Surface with Acoustic Vector Sensor
PublikacjaThis paper presents a new approach to detecting the presence of water on a road surface, employing an acoustic vector sensor. The proposed method is based on sound intensity analysis in the frequency domain. Acoustic events, representing road vehicles, are detected in the sound intensity signals. The direction of the incoming sound is calculated for the individual spectral components of the intensity signal, and the components...
-
Potential reduction of traffic noise by the means of increased fleet of electric vehicles using a combination of low-noise tyres and low-noise road surfaces
PublikacjaIn the future, the number of zero-emission vehicles like electric and plug-in hybrid vehicles (in electric mode) is expected to be a substantial part of the vehicle fleet. In Norway, such vehicles already account for approximately 20 % of all new cars sold. Since these vehicles emit negligible noise related to the power-train, the tyre/road noise is the dominating noise source. In the LEO project, tyres designed for such cars have...
-
Road texture influence on tyre rolling resistance
PublikacjaTyre performance, one of the critical factors for vehicle users, is strongly related to theroad surface characteristics, most notably to the pavement texture. Phenomena that occur at the tyre/road interface affect tyre friction (skid resistance), rolling resistance, tyre wear and tyre/road noise. This article deals with relationship between surface texture and rolling resistance of light and heavy vehicle tyres. Mean profile depth...
-
Engineering method of tire rolling resistance evaluation
PublikacjaTire rolling resistance is one of the most difficult tire parameters to measure. The reason is that for modern tires the force of rolling resistance corresponds to 0.5–1% of tire load, thus measurements of very small forces must be performed in a heavily loaded system. This constitutes great problems, especially in road conditions. Laboratory measurements are easier to perform, as the environment may be better controlled, but roadwheel...
-
Poroelastic Road Surface – a Promising Road Traffic Noise Abatement Solution
PublikacjaRoad surfaces have a direct impact on the generation of noise by rolling tyres, the main and dominant source of noise of moving vehicles, as well as may affect propagation of noise emitted by all noise sources of a vehicle. Thus there is no doubt that pavement should be considered as one of the major potential road traffic noise abatement measure. Low noise pavements of existing types may in new conditions provide up to 8 dB of...
-
Methods of Tire Rolling Resistance Measurements
PublikacjaTire rolling resistance is one of the factors related to tire/road interaction that has important influence on road vehicles performance. Raising fuel price and increased concern related to the environmental changes result in growing interest in reduction of tire rolling resistance that influences fuel consumption, especially in free-flowing highway traffic with moderate speeds. There are several methods of tire rolling resistance measurements....
-
Support Vector Machine Applied to Road Traffic Event Classification
PublikacjaThe aim of this paper is to present results of road traffic event signal recognition. First, several types of systems for road traffic monitoring, including Intelligent Transport System (ITS) are shortly described. Then, assumptions of creating a database of vehicle signals recorded in different weather and road conditions are outlined. Registered signals were edited as single vehicle pass by. Using the Matlab-based application...
-
Characterization of diatomaceous earth coated with nitrated asphaltenes as superior adsorbent for removal of VOCs from gas phase in fixed bed column
PublikacjaAsphaltenes isolated from bitumen possess unusual adsorption characteristics that can be further enhanced by chemical modifications to promote interactions with VOCs’. Herein, nitrated asphaltenes are used as an active layer coated on a surface of a diatomaceous earth, in order to prepare an efficient adsorbent (AsfNitro). Breakthrough experiments with benzene, pyridine, and 1-nitropropane revealed significant increase in adsorption...
-
Contribution of dynamic vehicle loads to pavement failure
PublikacjaPavement surfaces are not ideally even, which causes dynamic loads of vehicle axles. Distribution of dynamic loads of a given axle is similar to normal distribution and can be described by static load and dynamic load coefficient. The dynamic load coefficient depends on road profile, vehicle speed, properties of suspensions and static load of axle. While for a given road section road profile remains constant, vehicle speed and...
-
Temperature influence on tyre/road noise frequency spectra
PublikacjaThe correction for temperature effect on measured tyre/road noise is very important as it may be one of the main sources of errors in measurement results due to substantial influence of this parameter on obtained values. The latest version of the Technical Specification ISO/CD TS 13471-1 about Temperature Corrections contains a proposal of correction procedure for normalizing measured noise levels to a reference air temperature...
-
Impact of the surface evenness and texture on tire/road rolling resistance
PublikacjaThis paper deals with the issue of a surface's roughness and texture impact on tire/road rolling resistance. It includes a brief description of research aims, measurements and an analysis of results. It also presents observations and conclusions regarding drum facility modernisation which allows studies concerning surface's roughness and texture impact on tire/road rolling resistance.
-
The searchlight problem for road networks
PublikacjaWe consider the problem of searching for a mobile intruder hiding in a road network given as the union of two or more lines, or two or more line segments, in the plane. Some of the intersections of the road network are occupied by stationary guards equipped with a number of searchlights, each of which can emit a single ray of light in any direction along the lines (or line segments) it is on. The goal is to detect the intruder,...
-
The effects of selected factors on pedestrian crossings in urban areas
PublikacjaPedestrian crossings are designed to help pedestrians cross a road. There are at-grade pedestrian crossings with or without traffic lights and grade separated crossings such as subways and footbridges. Pedestrian crossings may be located next to a junction or on road sections between junctions. Where at-grade crossings are involved, pedestrians and motorists interact, which may lead to dangerous situations and road traffic conflicts....
-
Reduction of road traffic noise by source measures — present and future strategies
PublikacjaThe current trend worldwide is less focused on reducing road traffic noise. This is in strong contrast to the severe impact of traffic noise to the general health and quality of life. A more holistic and combined strategy is needed. Current international rules and regulations regarding vehicles and tyres are not sufficient to reduce traffic noise levels in an effective way. Calculations show that these regulations will only yield...
-
Tyre/road noise reduction by a poroelastic road surface
PublikacjaLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublikacjaTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
Examining Impact of Speed Recommendation Algorithm Operating in Autonomous Road Signs on Minimum Distance between Vehicles
PublikacjaAn approach to a new kind of recommendation system design that suggests safe speed on the road is presented. Real data obtained on roads were used for the simulations. As part of a project related to autonomous road sign development, a number of measurements were carried out on both local roads and expressways. A speed recommendation model was created based on gathered traffic data employing the traffic simulator. Depending on...
-
Testing the Weibull distribution in road traffic losses analysis
PublikacjaThe paper presents an attempt of applying the Weibull distribution for the purpose of analysing road traffic losses (fatalities). The question it asks is whether reliability engineering methods can be applied for the analyses. If this is the case, what should be the interpretation of the numbers and terms? It was assumed that the losses generated by a malfunctioning road transport system are fatalities. Risk exposure to these losses...
-
Influence of Road Wetness on Tire-Pavement Rolling Resistance
PublikacjaRolling resistance of tires is one of the most important factors influencing energy consumption of road vehicles, especially on rural roads. For practical reasons, most of rolling resistance measurements are usually performed for dry road conditions. Based on the fact that roads are wet during a considerable time over the year and as part of the projects MIRIAM, ROLRES and ROSANNE, the TUG (Technical University of Gdańsk) in Poland...
-
Experimental validation of the rolling resistance measurement method including updated draft standard
PublikacjaThe main objective of ROSANNE is the harmonisation and standardisation of the measurement of skid resistance, noise emission and rolling resistance of road pavements. Regarding rolling resistance characterisation, a draft for standardization of a harmonized procedure for classification of road surfaces across Europe has been prepared within WP3 (deliverable 3.5). The procedure deals with the direct measurement on real roads of...
-
DESIGN AND CALIBRATION OF ROLLING RESISTANCE TEST TRAILER R2mk.2
PublikacjaThe paper describes construction nad calibration procedures of the rolling resistance test trailer R2 Mk2. The trailer is design to measure rolling resistance of passenger car tyres in various road conditions on trafficked road. The trailer utilizes so called angle method also known as vertical arm method. The paper presents also calibration procedures that are necessary to ascertain good precision of the measurements.
-
INFLUENCE OF LOAD AND INFLATION PRESSURE ON THE TYRE ROLLING RESISTANCE
PublikacjaTyre load and inflation pressure are important factors controlling rolling resistance of road vehicles. The article presents results obtained in the Technical University of Gdańsk during laboratory and road measurements of different car tyres rolling on different pavements. The knowledge of rolling resistance characteristics is important for modelling car dynamics as well as fuel consumption. It is also necessary to establish proper...
-
THE INVESTMENT ENVIRONMENT MANAGEMENT SYSTEM IN THE FRAMEWORK OF LEGAL SUPPORT AS A FACTOR OF NATIONAL SAFETY
Publikacja -
Identification of Kinematic Excitation Function by the Modal Coordinates Estimation of the System's Dynamics
PublikacjaThe paper presents a method of the kinematic excitation courses’ identification in excitation points, based on the car road test acceleration at different measurement points. For the purpose of the laboratory fatigue life investigation of contemporary complex structures (e.g. cars bodies) and components of these structures (i.e. cars roofs), only a few first vibration modes are usually taken into account. During real life tests...
-
Estimation of Average Speed of Road Vehicles by Sound Intensity Analysis
PublikacjaConstant monitoring of road traffic is important part of modern smart city systems. The proposed method estimates average speed of road vehicles in the observation period, using a passive acoustic vector sensor. Speed estimation based on sound intensity analysis is a novel approach to the described problem. Sound intensity in two orthogonal axes is measured with a sensor placed alongside the road. Position of the apparent sound...
-
The Application of Granulated Expanded Glass Aggregate with Cement Grout as an Alternative Solution for Sub-Grade and Frost-Protection Sub-Base Layer in Road Construction
PublikacjaThe purpose of the research was to assess the possibility of using granulated expanded glass aggregate (GEGA) with cement grout as a replacement of a sub-grade and frost-protection layer, made of natural fine aggregates (NATU), stabilized with a hydraulic binder. Instead of traditional parts of the road construction, such as the sub-grade and frost-protection layer with the application of fine aggregate, stabilized with cement,...
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublikacjaTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
Modeling of hazards, consequences and risk for safety assessment of ships in damaged conditions in operation
PublikacjaPraca dotyczy problematyki związanej z modelowaniem zagrożeń, konsekwencji i ryzyka, w metodzie oceny bezpieczeństwa statków w stanie uszkodzonym. Metoda oparta jest na podejściu zorientowanym na ocenę zachowania się statku i ocenę ryzyka wypadku. Kolejne moduły metody dotyczą identyfikacji zagrożeń i scenariuszy wypadków oraz oceny i kontroli ryzyka. Ocenę ryzyka można przeprowadzić przy zastosowaniu elementów metodyki Przypadku...
-
Functional safety and cyber security analysis for life cycle management of industrial control systems in hazardous plants and oil port critical infrastructure including insurance
PublikacjaThis report addresses selected methodological aspects of proactive reliability, functional safety and cyber security management in life cycle of industrial automation and control systems (IACS) in hazardous plants and oil port critical installations based on the analysis of relevant hazards / threats and evaluation of related risks. In addition the insurance company point of view has been also considered, because nowadays the insurer,...
-
Speed, Alcohol and Safety Belts as Important Factors Influencing the Number of Fatalities in Road Accidents in the Voivodships
Publikacja -
Diagnosis of damages in family buildings using neural networks
PublikacjaThe article concerns a problem of damages in family buildings, which result from traffic-induced vibrations. These vibrations arise from various causes and their size is influenced by many factors. The most important is the type of a road, type and weight of vehicles that run on the road, type and condition of the road surface, the distance from the house to the source of vibrations and many others which should be taken into account....
-
Comparison of pavement noise properties on selected road sections using different CPX measuring systems: self-powered vehicle and special test trailer
PublikacjaThe recently published ISO standard intended to measure the noise properties of road surfaces in a standardized method (ISO 11819-2:2017) precisely defines measurement procedure of the influence of road surface on traffic noise. According to it, two types of test vehicles may be utilized: a self-powered vehicle fitted with one or more test tyres and a trailer towed by a separate vehicle with one or more test tyres mounted on the...