Wyszukiwarka
Filtry
wszystkich: 1617
wybranych: 1302
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: Thin films morphology
-
Morphology and properties of nanotubular oxide layer on the Ti13Zr13Nb alloy
PublikacjaThe Ti13Zr13Nb alloy in solid and porous form was oxidised. The constant voltage 20 V, oxidation time 0.5 and 1 h, and 1 M H3PO4 (orthophosphoric acid) with addition of HF (hydrofluoric acid) as a test solution were applied. SEM (Scanning Electron Microscope) examinations of surface, EDS (Energy Dispersive X-ray Spectroscopy) chemical analysis, nanohardness and nano-scratch tests, and corrosion potentiokinetic tests at various...
-
MORPHOLOGY OF BUILDING DEVELOPMENT AS AN ELEMENT OF URBAN VENTIALTION SYSTEM
PublikacjaProblems related to air quality in large urban agglomerations (e.g., high concentration of pollutants, the urban heat island phenomenon) make it necessary to take comprehensive measures to improve air exchange in urban areas.The article concerns the relationship between wind phenomena observable in cities and the geometrical features of building development. The knowledge on the subject is already well-founded and has been intensively...
-
Effect of Bi2O3 Excess on Morphology and Structure of BiNbO4 Ceramics
PublikacjaGoal of the present research was to fabricate BiNbO4 ceramics from the mixture of powders by the solid state reaction route and pressureless sintering at various temperatures (TS =8700C and TS =9100C) and study microstructure, phase composition and crystalline structure of BiNbO4 ceramics. Four batches were fabricated and examined, namely the one fabricated from the stoichiometric mixture of reagent – grade oxide powders, viz....
-
Elastic distortional buckling of thin-walled bars of closed quadratic cross-section
PublikacjaIn this study a thin-walled bar with closed quadratic cross-section is considered. The elastic stability of axially compressed bar related to the cross-section distortion is investigated. The governing differential equation is derived with aid of the principle of stationary total potential energy. The critical load for the simply supported bar is found in analytical form and it is compared with the FEM solution. Sufficient accuracy...
-
The ILs-assisted electrochemical synthesis of TiO2 nanotubes: The effect of ionic liquids on morphology and photoactivity
PublikacjaFacile and environmentally benign one-step titanium anodization method for TiO2 nanotubes (NTs) formation in a presence of ionic liquids (ILs) was proposed. Influence of the IL structure and its content in ethylene glycol electrolyte on morphology, surface properties and photoactivity of the TiO2 NTs was investigated. Possible interactions between IL and TiO2 NTs as well as the mechanism of NTs formation during anodic oxidation...
-
The Idea of Using Adhesive Bonds in Shaping of Cold-formed Thin-walled Beam-columns
PublikacjaThe chapter concerns the idea of using adhesive bonds in the shaping of cold-formed thin-walled beam-columns. The idea of adhesive-bonded connections is not new but is unlikely to have been used in the design and shaping of thin-walled beam-columns in civil engineering up to date. Metal bar structures, including (due to economic reasons) thin-walled structures, are the most common and effective means to build engineering superstructures/loadbearing...
-
Investigation of natural frequencies of axially loaded thin-walled columns
PublikacjaThe paper deals with correlation between natural frequencies of two steel thin-walled columns and the corresponding applied load. The structures are made of cold-formed lipped channel sections. The columns lengths were assumed to follow two buckling patterns – global flexural and flexural-torsional buckling. In the thicker structure two material models were considered – linearly-elastic and elastic-perfectly plastic. Numerical...
-
Controlling crystallites orientation and facet exposure for enhanced electrochemical properties of polycrystalline MoO3 films
PublikacjaThis study focuses on the development and optimization of MoO3 films on commercially available FTO substrates using the pulsed laser deposition (PLD) technique. By carefully selecting deposition conditions and implementing post-treatment procedures, precise control over crystallite orientation relative to the substrate is achieved. Deposition at 450 °C in O2 atmosphere results in random crystallite arrangement, while introducing...
-
Cross-linking of polymer films using phenol-formaldehyde resins with different functional groups
PublikacjaWell-know phenol-formaldehyde resins are used in the production of press-materials, glues, protective coating, mastics. They take a special place among known oligomers because the products based on them are characterized by a low cost and a series of positive properties. Aim of the work: to show the possibility to create polymeric films based on epoxy resins and modified phenol-formaldehyde resins, which contain unsaturated double...
-
Morphology and mechanical properties of polyamide/clay nanocomposites toughened with NBR/NBR-g-GMA: A comparative study
PublikacjaThis work highlights the importance of nanoclay dispersion state in the nanocomposites containing polyamide 6 (PA6), nanoclay and elastomers as well as clay localization at the interface of thermoplastic/elastomer. Morphology and mechanical properties of a series of nanocomposites containing acrylonitrile butadiene rubber (NBR), glycidyl methacrylate-grafted NBR (NBR-g-GMA), and combined NBR/NBR-g-GMA were compared and discussed...
-
Optical properties of thin TiO2 film deposited on the fiber optic sensor head
PublikacjaThe presented study was focused on investigation of the titanium dioxide (TiO2) thin film deposited on the fiber tip. The intention of this investigation was using TiO2 film in the construction of the optical fiber sensor head. In the demonstrated construction TiO2 thin layer was deposited on the tip of a commonly used telecommunication single mode optical fiber (SMF-28) by means of the Atomic Layer Deposition (ALD). Thickness...
-
Curing characteristics, mechanical properties and morphology of butyl rubber filled with ground tire rubber (GTR)
PublikacjaThe results on testing application of ground tire rubber (GTR), as potential filler for butyl rubber, are pre- sented. The GTR content variation, within the range of 10–90 phr, was studied with respect to the vulcanization process, static mechanical properties (tensile strength, elongation-at-break, hardness and resilience), dynamic mechanical properties and the morphology of the obtained vulcanizates. Butyl rubber was characterized...
-
On the Nonlinear Effects of Magnetoacoustic Perturbations in Optically Thin Quasi-Isentropic Plasmas
PublikacjaNonlinear effects of planar magnetosound perturbations in a plasma are discussed. Plasma is non-adiabatic due to optically thin radiation and external heating. For these reasons, thermal instability of a plasma may appear which makes it acoustically active. The plasma is assumed to be initially homogeneous ideal gas with infinite electrical conductivity permeated by a straight magnetic field which is orthogonal to the trajectories...
-
Application of Thin ZnO ALD Layers in Fiber-Optic Fabry-Pérot Sensing Interferometers
PublikacjaIn this paper we investigated the response of a fiber-optic Fabry-Pérot sensing interferometer with thin ZnO layers deposited on the end faces of the optical fibers forming the cavity. Standard telecommunication single-mode optical fiber (SMF-28) segments were used with the thin ZnO layers deposited by Atomic Layer Deposition (ALD). Measurements were performed with the interferometer illuminated by two broadband sources operating...
-
Thin-walled cross section shape influence on steel member resistance.
PublikacjaThis work describes why trending thin-walled technology is achieving popularity in steel construction sector. A purpose of this article is to present the influence of the cold-formed element cross-section shape on an axial compression and a bending moment resistance. The authors have considered four different shapes assuming constant section area and thickness. Calculations were based on three different steel grades taking into...
-
Comprehensive exploration of technological tensioning effects in welded thin plate girders: an in-depth investigation
PublikacjaThin-walled plate girders are widely used in structures and construction due to their effectiveness in transferring loads. The permanent deformations of the girder lead to a lack of stability, which necessarily leads to its replacement. Replacing permanently deformed thin-walled load-bearing structures requires large financial outlays. Technological prestressing is one of the most effective methods for studying and treating permanent...
-
Numerical analysis of influence of intermediate stiffeners setting on the stability behaviour of thin-walled steel tank shell
Publikacja -
Self-Organization of Graft Copolymers and Retortable iPP-Based Nanoporous Films Thereof
PublikacjaPolyolefins might become inexpensive alternatives to the existing membranes based on polyethersulfone. Here we disclose the production of retortable, well-defined PP-based nanoporous membranes derived from amphiphilic graft copolymer precursors. The graft copolymers, containing a polypropylene backbone and polyester grafts, were obtained by grafting lactones, specifically δ-valerolactone and ε-caprolactone, from well-defined randomly...
-
Multiple Reprocessing of Conductive PLA 3D-Printing Filament: Rheology, Morphology, Thermal and Electrochemical Properties Assessment
PublikacjaAdditive manufacturing technologies are gaining more and more attention, resulting in the development or modification of 3D printing techniques and dedicated materials. On the other hand, economic and ecological aspects force the industry to develop material recycling strategies. In this work, the multiple reprocessing of a commercially available PLA conductive composite with carbon black filler, dedicated to 3D printing, was investigated....
-
The ILs-assisted solvothermal synthesis of TiO2 spheres: the effect of ionic liquids on morphology and photoactivity of TiO2
PublikacjaEffect of the ionic liquid (IL) structure (chain length in the imidazolium cation) on morphology and photoactivity of TiO2 particles has been systematically investigated. The TiO2 microspheres have been successfully synthesized via facile solvothermal method assisted by ionic liquids, such as 1-butyl-3-methylimidazolium chloride [BMIM][Cl] and 1-decyl-3-methylimidazolium chloride [DMIM][Cl] using tetra-tert-butyl orthotitanate...
-
Shielded coupled strip and slot guides with a thin omega pseudochiral medium layer
PublikacjaA method of moments combined with mode matching technique is applied to analyze the shielded coupled strip and slot line structures containing a thin plate of Omega pseudochiral medium. The boundary problems are simplified by introducing for omega medium the approximate continuity conditions. Such mathematical model allows to examine the field displacement effect appearing in the considered guide resulting from the coupling between...
-
Ionic liquid as morphology-directing agent of two-dimensional Bi2WO6: New insight into photocatalytic and antibacterial activity
PublikacjaAn efficient and durable utilization of light to drive photocatalytic reactions still requires the overcoming of barriers. Herein, two-dimensional (2D) ultrathin IL_Bi2WO6 (IL_BWO) photocatalysts were prepared for the first time via ionic liquid-assisted hydrothermal route by adjusting the amount of tetrabutylammonium chloride [TBA][Cl], synthesis temperature and duration. IL played the role of morphology-directing agent given...
-
CGO FILMS ON YSZ ELECTROLYTE FABRICATED BY SPRAY PYROLYSIS FOR SOFC
PublikacjaINTRODUCTION Solid oxide fuel cells are one of the fastest developing energy converters. The advancement introduced by research community provides steady state progress is stability and performance of the fuel cells. Significant influence on the cell’s performance and stability is related to cell design. The simplest design just consists of an anode, a solid electrolyte and a cathode. However, in order to improve the properties,...
-
Tailoring the optical parameters of optical fiber interferometer with dedicated boron-doped nanocrystalline diamond thin film
PublikacjaOptical fiber interferometer using nanocrystalline boron-doped diamond film was investigated. The diamond films were deposited on glass plates using a Microwave Plasma-Enhanced Chemical Vapour Deposition (μPE CVD) sys-tem. The growth time was 3h, with boron doping level of 10 000 ppm producing films (B-NCD-10) of thickness ~ 200 nm. The presence of boron atoms in the diamond film is evident in Raman spectrum as peaks at 1212 cm-1...
-
The progress in characterization of polyurethanes morphology with different microscopic methods----WYJAŚNIĆ-----
PublikacjaW pracy opisano wyniki badań dotyczące analizy morfologii poliuretyanów określanej różnymi metodami. Omówiono mikroskopię optyczną, elektronową, mikroskopię termiczną, mikroskopię fluoroscencyjną, mikro-Ramana i mikroskopię sił atomowych.
-
Does morphology of carotid plaque depend on patient's oxidative stress?
Publikacja -
Left Ventricular Mass: Correlation with Fatness, Hemodynamics and Renal Morphology
Publikacja -
Morphology, Thermo-Mechanical Properties and Biodegradibility of PCL/PLA Blends Reactively Compatibilized by Different Organic Peroxides
PublikacjaReactive blending is a promising approach for the sustainable development of bio-based polymer blends and composites, which currently is gaining more and more attention. In this paper, biodegradable blends based on poly(ε-caprolactone) (PCL) and poly(lactic acid) (PLA) were prepared via reactive blending performed in an internal mixer. The PCL and PLA content varied in a ratio of 70/30 and 55/45. Reactive modification of PCL/PLA...
-
Torsion of restrained thin-walled bars of open constant bisymmetric cross-section
PublikacjaElastic and geometric stiffness matrices were derived using Castigliano's first theorem, for the case of torsion of restrained thin-walled bars of open constant bisymmetric cross-section. Functions which describe the angles of torsion were adopted from the solutions of thedifferential equation for restrained torsion. The exact solutions were simplified by expanding them in a power series. Numerical examples were taken from Kujawa...
-
Morphology, surface properties and photocatalytic activity of the bismuth oxyhalides semiconductors prepared by ionic liquid assisted solvothermal method
PublikacjaThis is the first report of the effect of the ILs cation type (imidazolium, pyridinium and pyrrolidinium) on the morphology, surface properties and photoactivity of BiOX semiconductors type obtained by solvothermal method in glycerol. The various ionic liquids (IL) cation type as a halogen source and templating agent for the synthesis of the bismuth oxyhalides nanoparticles has been systematically investigated. The role of ILs...
-
Investigation of thin perovskite layers between cathode and doped ceria used as buffer layer in solid oxide fuel cells
PublikacjaIn this paper, thin perovskite layers between cathode material of solid oxide fuel cells and gadolinia-doped ceria buffer layer are investigated. Thin layers made of LaNi0.6Fe0.4O3-δ (LNF), La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF), or SrTi0.65Fe0.35O3-δ (STF) were symmetrically deposited by spin coating method from metallo-organic polymer precursors on a Ce0.8Gd0.2O2-δ (CGO) substrate. Porous and about 40-μm-thick LNF cathodes were deposited...
-
Coplanar Waveguide-Fed Broadband Microwave Devices with (or without) a Thin Dielectric Substrate for Use in Flexible Electronic Systems
PublikacjaTwo examples of microwave devices, fed by a coplanar waveguide and realized on a thin substrate (or without such a substrate), are employed to investigate the influence of devices’ curvatures and the proximity of different materials on their parameters. To perform the tests, a broadband antenna and a low-pass filter are chosen. A feeding coplanar waveguide is realized on a dielectric material brick attached to an SMA connector...
-
Preparation, characterization and antimicrobial activity of polyvinyl alcohol/gum arabic/chitosan composite films incorporated with black pepper essential oil and ginger essential oil
PublikacjaIn this study, biocomposite films based on polyvinyl alcohol (PVA), gum arabic (GA) and chitosan (CS) incorporated with BPEO and GEO were fabricated by solvent casting method. FTIR, XRD, SEM and DSC were performed with mechanical and antimicrobial properties of PVA/GA/CS films with and without BPEO and GEO. The BPEO and GEO incorporated PVA/GA/CS films were significantly inhibited the growth of Bacillus cereus, Staphylococcus aureus,...
-
Low-Coherence Interferometer with Nanocrystalline Diamond Films with Potential Application to Measure Small Biological Samples
PublikacjaThe study investigates a case of a low-coherence fiber-optic Fabry–Prerot interferometer with a nanocrystalline diamond (NCD) mirror. The method of achieving double density of interference fringes is proposed by the application of birefringent material in the cavity of the interferometer. It can be used to reduce sample volume in comparison to conventional interferometers. The use of a biocompatible diamond mirror makes it specifically...
-
Electromodulation of monomer and excimer phosphorescence in vacuum-evaporated films of platinum (II) complexes of 1,3-di(2-pyridyl)benzenes
PublikacjaElectric field-modulated photoluminescence (EML) measurements are presented for vacuum-evaporated films of cyclometallated Pt (II) complexes of 1,3-di(2-pyridyl) benzenes used as triplet emitters in organic light-emitting diodes (OLEDs). The excimer phosphorescence is quenched by the external electric field of 2.5 MV/cm up to 25% but the same effect on monomer phosphorescence is one order of magnitude smaller. The higher quenching...
-
On modelling and non-linear elasto-plastic analysis of thin shells with deformable junctions
PublikacjaThe undeformed base surface of the irregular thin shell is modelled by the union of a finite number of regular smooth surface elements joined together along spatial curvilinear surface edges. The equilibrium conditions are formulated by postulating an appropriate form of the principle of virtual work, where also deformability of shell junctions is taken into account. The PVW is then discretised by C1 finite elements and the incremental-iterative...
-
Effect of high loading of titanium dioxide particles on the morphology and selected properties of natural rubber-based composites
PublikacjaThe aim of this work was to prepare and characterize the natural rubber vulcanizates contained different amounts of titanium dioxide particles. At first rubber mixture was prepared using a laboratory two-roll mill and then samples were vulcanized in a hydraulic press. The formulation of rubber mixture and rubber-processing technique is based on our earlier investigations. Materials were obtained at the different titanium dioxide...
-
Local buckling of thin-walled channel member flange made of aluminum alloy
PublikacjaThe paper deals with local stability of the thin-walled compressed flange of channel columns and beams made of aluminum alloy. The aim of paper is to find critical stress of local buckling of the flange member taking into account the web-flange interaction in linear and nonlinear elastic range of the member material. The governing differential equation of the problem is derived with aid of the principle of stationary total potential...
-
Random field modelling of mechanical behaviour of corroded thin steel plate specimens
PublikacjaThe objective of this work is to explore the possibility of corrosion degradation modelling of thin steel plate specimens with the use of random field approach. The mechanical properties are obtained via the nonlinear Finite Element Analysis with the use of an explicit dynamic solver. The fully nonlinear material model is adopted to obtain the proper stress-strain response. Sensitivity analysis considering the main statistical...
-
Sensitivity analysis of free torsional vibration frequencies of thin-walled laminated beams under axial load
PublikacjaThe paper addresses sensitivity analysis of free torsional vibration frequencies of thin-walled beams of bisymmetric open cross-section made of unidirectional fibre-reinforced laminate. The warping effect and the axial end load are taken into account. The consideration is based upon the classical theory of thin-walled beams of non-deformable cross-section. The first-order sensitivity variation of the frequencies is derived with...
-
Assessment of dynamic characteristics of thin cylindrical sandwich panels with magnetorheological core
PublikacjaBased on the equivalent single-layer linear theory for laminated shells, free and forced vibrations of thin cylindrical sandwich panels with magnetorheological core are studied. Five variants of available magnetorheological elastomers differing in their composition and physical properties are considered for smart viscoelastic core. Coupled differential equations in terms of displacements based on the generalized kinematic hypotheses...
-
Enhancement of fiber-optic low-coherence Fabry-Pérot interferometer with ZnO ALD films
PublikacjaIn this paper investigation of the enhanced fiber-optic low coherence Fabry-Pérot interferometer with zinc oxide (ZnO) film deposited by atomic layer deposition (ALD) was presented. Model of the interferometer, which was constructed of single-mode optical fiber with applied ZnO ALD films, was built. The interferometer was also examined by means of experiment. Measurements were performed for both reflective and transmission modes,...
-
Cross-Linking, Morphology, and Physico-Mechanical Properties of GTR/SBS Blends: Dicumyl Peroxide vs. Sulfur System
PublikacjaIn this work, ground tire rubber and styrene–butadiene block copolymer (GTR/SBS) blends at the ratio of 50/50 wt%, with the application of four different SBS copolymer grades (linear and radial) and two types of cross-linking agent (a sulfur-based system and dicumyl peroxide), were prepared by melt compounding. The rheological and cross-linking behavior, physico-mechanical parameters (i.e., tensile properties, abrasion resistance,...
-
Determination of buckling strength of silos composed of corrugated walls and thin-walled-columns using simplified wall segment models
PublikacjaW artykule przedstawiono wyniki obszernych analiz numerycznych wyboczenia i stateczności metalowych silosów z blachy falistej wzmocnionych cienkościennymi słupami. Wykonano analizy liniowe i nieliniowe. Do obliczeń zaproponowano proste modele segmentów ścian zamiast skomplikowanych modeli całych silosów. Otrzymano bardzo dobrą zgodność wyników numerycznych. Wyniki obliczeń numerycznych porównano dodatkowo z wynikami normowymi.
-
Interactions of fish gelatin and chitosan in uncrosslinked and crosslinked with EDC films: FT-IR study
PublikacjaFilms based on fish gelatin, chitosan and blend of fish gelatin and chitosan before and after cross-linking with EDC have been characterized by FT-IR spectroscopy. The FT-IR spectrum of fish gelatin film showed the characteristic amide I, amide II and amide III bands, and the FT-IR spectrum of chitosan film confirmed that the polymer was only a partially deacetylated product, and included CH3-C=O and NH2 groups, the latter both...
-
Fluctuation enhanced gas sensing using UV irradiated Au-nanoparticle-decorated WO3-nanowire films
PublikacjaWO3 nanowires (WO3-NWs) decorated with gold nanoparticles (AuNPs) were utilized in resistive gas sensor devices to detect ethanol by use of fluctuation enhanced sensing (FES). The experimental system records both DC resistance and fluctuations of the sensing film. Our data verify that the sensitivity and selectivity of the gas sensor are improved by applying FES when the sensor is stimulated with a combination of UV light and heating....
-
Fatigue fracture morphology of AISI H13 steel obtained by additive manufacturing
PublikacjaThe paper focuses on researching the effect of fatigue loading on metallic structure, lifetime, and fracture surface topographies in AISI H13 steel specimens obtained by selective laser melting (SLM). The topography of the fracture surfaces was measured over their entire area, according to the entire total area method, with an optical three-dimensional surface measurement system. The fatigue results of the SLM 3D printed steel...
-
Hybrid carbon-TiO2 spheres: Investigation of structure, morphology and spectroscopic studies
Publikacja -
Silica xerogel-hydrogen peroxide composite: their morphology, stability, and antimicrobial activity
PublikacjaOpracowano metody otrzymywania stabilnego kompozytu złożonego z kserożelu krzemionkowego i nadtlenku wodoru w szerokim zakresie stężeń H2O2. Przeprowadzono charakterystykę otrzymanego kompozytu. W szczególności określono morfologię kompozytu, stabilność termiczną oraz dokonano oceny właściwości bakteriobójczych preparatu.
-
Silica xerogel–hydrogen peroxide composites: Their morphology, stability, and antimicrobial activity
Publikacja