Filtry
wszystkich: 4860
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: OPTIMAL BOILING PARAMETERS
-
Impact of thermal backfill parameters on current-carrying capacity of power cables installed in the ground
PublikacjaProper design of power installations with the participation of power cables buried in homogeneous and thermally well-conductive ground does not constitute a major problem. The situation changes when the ground is non-homogeneous and thermally low-conductive. In such a situation, a thermal backfill near the cables is commonly used. The optimization of thermal backfill parameters to achieve the highest possible current-carrying capacity...
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublikacjaThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
Aleksandra Parteka dr hab. inż.
OsobyAbout me: I am an associate professor and head of doctoral studies at the Faculty of Management and Economics, Gdansk University of Technology (GdanskTech, Poland). I got my MSc degree in Economics from Gdansk University of Technology (2003) and Universita’ Politecnica delle Marche (2005), as well as MA degree in Contemporary European Studies from Sussex University (2006, with distinction). I received my PhD in Economics...
-
Pyrolysis Combined with the Dry Reforming of Waste Plastics as a Potential Method for Resource Recovery—A Review of Process Parameters and Catalysts
Publikacja: Emissions of greenhouse gases and growing amounts of waste plastic are serious environmental threats that need urgent attention. The current methods dedicated to waste plastic recycling are still insufficient and it is necessary to search for new technologies for waste plastic management. The pyrolysis-catalytic dry reforming (PCDR) of waste plastic is a promising pro-environmental way employed for the reduction of both CO2 and...
-
Residue-Pole Methods for Variability Analysis of S-parameters of Microwave Devices with 3D FEM and Mesh Deformation
PublikacjaThis paper presents a new approach for variability analysis of microwave devices with a high dimension of uncertain parameters. The proposed technique is based on modeling an approximation of system by its poles and residues using several modeling methods, including ordinary kriging, Adaptive Polynomial Chaos (APCE), and Support Vector Machine Regression (SVM). The computational cost is compared with the traditional Monte-Carlo...
-
The optimal mixture of Toxoplasma gondii recombinant antigens (GRA1, P22, ROP1) for diagnosis of ovine toxoplasmosis
PublikacjaToxoplasmosis, caused by Toxoplasma gondii, is the major parasitic disease affecting sheep. Infection not only results in significant reproductive losses in these animals, but has public health implications since consumption of infected meat can facilitate zoonotic transmission. Although several serological tests are currently used for diagnosis of ovine toxoplasmosis, production of reliable reagents is a constraint and therefore...
-
Interspecies distances between propionic acid degraders and methanogens in syntrophic consortia for optimal hydrogen transfer
PublikacjaA mixed culture from an anaerobic biowaste digester was enriched on propionate and used to investigate interspecies hydrogen transfer in dependence of spatial distances between propionate degraders and methanogens. From 20.3 mM propionate, 20.8 mM acetate and 15.5 mM methane were formed. Maximum specific propionate oxidation and methane formation rates were 49 and 23 mmol mg−1day−1, respectively. Propionate oxidation was inhibited by...
-
The Optimal Spindle Speed Map for Reduction of Chatter Vibration During Milling of Bow Thruster Blade
PublikacjaW artykule przedstwiono przykład wykorzystania procedury tworzenia mapy optymalnych prędkosci obrotowych w celu ograniczenia drgań samowzbudnych podczas frezowania płata śruby okrętowego steru strumieniowego.
-
Designing optimal operational-point trajectories using an intelligent sub-strategy agent-based approach
PublikacjaW rozdziale opisuje się metodę projektowania optymalnej i bezpiecznego sterowania nieliniowymi procesami dynamicznymi. Poszukiwane sterowanie jest wynikiem zastosowania elementarnej strategii poszczególnych agentów, realizujšcych zadanie minimalizacji wspólnej miary kosztu sterowania. Zagadnienie projektowania optymalnego sterowania traktowane jest jako proces decyzyjny, w którym decyzje podejmowane sš w kolejnych regionach przestrzeni...
-
Chatter Vibration Surveillance by the Optimal-linear Control of Spindle Speed and Randomly Varying Spindle Speed
PublikacjaW artykule opisano dynamikę procesu skrawania smukłym frezem kulistym. Jako metodę nadzorowania drgań chatter zastosowano zmienną prędkość obrotową wrzeciona. Jest ona dobierna z wykorzystaniem energetycznego wskaźnika jakości co prowadzi do optymalno-liniowego sterowania prędkością obrotową. Dodatkowo zastosowano nadzorowanie drgań chatter poprzez losowo zmienną prędkość obrotową.
-
Designing optimal operational-point trajectories using an intelligent sub-strategy agent-based approach
PublikacjaW rozdziale opisuje się metodę projektowania optymalnej i bezpiecznego sterowania nieliniowymi procesami dynamicznymi. Poszukiwane sterowanie jest wynikiem zastosowania elementarnej strategii poszczególnych agentów, realizujących zadanie minimalizacji wspólnej miary kosztu sterowania. Zagadnienie projektowania optymalnego sterowania traktowane jest jako proces decyzyjny, w którym decyzje podejmowane są w kolejnych regionach przestrzeni...
-
Creation of a map of optimal spindle speeds for a purpose of surveillance of high speed milling of flexible details
PublikacjaDrgania samowzbudne typu chatter często towarzyszą procesom frezowania szybkościowego. Ich skutkiem są nieodwracalne uszkodzenia powierzchni obrabianej. Mogą one również doprowadzić do intensywnego zużycia narzędzi skrawających, a nawet samej obrabiarki. W pracy przedstawiono metodę umożliwiającą tworzenie mapy optymalnych prędkości obrotowych wrzeciona. Stosowanie podczas procesu frezowania optymalnej prędkości obrotowej wrzeciona...
-
Creating neural models using an adaptive algorithm for optimal size of neural network and training set.
PublikacjaZaprezentowano adaptacyjny algorytm generujący modele neuronowe liniowych układów mikrofalowych, zdolny do oszacowania optymalnego rozmiaru zbiory uczącego i sieci neuronowej. Stworzono kilka modeli nieciągłości falowodowych i mokropaskowych, a następnie zweryfikowano ich poprawność porównując wyniki analiz metodą dopasowania rodzajów i metodą momentów filtrów pasmowo-przepustowych.
-
Problem of optimal load distribution between generators minimizing risk of enegretic ship system overload.
PublikacjaOmówiono system rozdziału mocy czynnych pomiędzy generatorami w systemie energetycznym statku. Minimalizuje się ryzyko przeciążeń systemu przy jednoczesnej minimalizacji kosztów wytwarzania energii w systemie.
-
Bending Moment Control and Weight Optimization in Space Structures by Adding Extra Members in the Optimal Locations
PublikacjaThis paper investigates the reduction of bending moment in critical members by adding some extra members in the optimum location. Instead of enlarging the size of members to resist the moment, eight additional members are added in the optimum location to reduce the bending moment in the critical members. The total weight of the proposed structure with extra members is less than that of the original structure that resists the induced...
-
Effect of GIS parameters on modelling runoff from river basin. The case study of catchment in the Puck District
PublikacjaThe study was preceded to check the impact of the adopted digital elevation model resolution on the determination of catchment parameters and the further influence of the received information on calculations related to the hydrograph at the closing point of the basin after a synthetic 100-year precipitation episode. The study area are river basins located in the Puck commune convoying water directly to the Puck Bay. These studies...
-
A semi-empirical method for calculation of flow boiling heat transfer coefficients for conventional channels and small diameter tubes
PublikacjaW pracy przedstawiono rozważania na temat modelowania dwufazowego przepływu wrzącego w kanałach konwencjonalnych i w kanałach o małej średnicy. Przedstawiono modyfikację korelacji zaproponowanej wcześniej przez J. Mikielewicza na podstawie nowych danych eksperymentalnych, uzyskanych dla kanałów o małej średnicy. Bank danych obejmował ponad 460 punktów pomiarowych dla czynników R141b, R134a, R113, R123, R12, R11 i wody. Uzyskano...
-
Non-isothermal effects in a common method for calculation of heat transfer coefficient in flow boiling and flow condensation in minichannels
PublikacjaW pracy przestawiono efekty nieizotermiczne w metodzie wyznaczania współczynnika przejmowania ciepła podczas wrzenia w przepływie oraz kondensacji w przepływie w minikanałach. Wyniki obliczeń porównano z badaniami eksperymentalnymi z literatury, uzyskując dobrą zgodność.
-
Improved semi-empirical method for determination of heat transfer coefficient in flow boiling in conventional and small diameter tubes
PublikacjaPraca dotyczy przedstawienia poprawionego modelu umożliwiającego wyznaczanie współczynnika przejmowania ciepła w kanałach o małych średnicach jaj i tych tradycyjnych. Model zweryfikowano na 6 czynnikach chłodnuiczych uzyskując bardzo zadowalającą zgodność.
-
Measuring moisture damage of asphalt mixtures: The development of a new modified boiling test based on color image processing
Publikacja -
A common method for calculation of flow boiling and flow condensation heat transfer coefficients in minichannels with account of nonadiabatic effects
PublikacjaW pracy przedstawiono metodę ogólną wyznaczania współczynników przejmowania ciepła podczas wrzenia w przepływie i kondensacji w przepływie w minikanałach z uwzględnieniem efektu nieadiabatycznego. Uwzględnia ona wpływ modyfikacji naprężeń stycznych na granicy ciecz-para na wymianę ciepła.
-
Badania wrzenia R22 w rurkach z powłoką porowatą. Investigation of R22 flow boiling in porous tubes.
PublikacjaW pracy przedstawiono wyniki pomiarów współczynnika przejmowania ciepła przy wrzeniu w przepływie R22 w poziomej rurce z aluminiową powłoką porowatą. Otrzymane dane odniesiono do wyników uzyskanych dla gładkiej stalowej rurki oraz rurki typu microfin. Rurka gładka i z powłoką porowatą była wykonana ze stali nierdzewnej o grubości ścianki 0.6 mm. Grubość powłoki porowatej wynosiła 0,2 mm. Eksperymenty prowadzono przy stopniu suchości...
-
Experimental investigation of M-shape heat transfer coefficient distribution of R123 flow boiling in small-diameter tubes
PublikacjaW publikacji przedstawiono wyniki badań wrzenia czynnika R123 w srebrnych rurkach o małych średnicach (średnice wewnętrzne wynosiły odpowiednio 1.15 mm i 2.3 mm). Badania przeprowadzono w szerokim zakresie stopnia suchości pary (0.01-0.9), gęstości strumienia masy (650-3000 kg/(m2s)) oraz gęstości strumienia ciepła (40-80 kW/m2). W badaniach wykazano, że istnieją dwa lokalne maksima współczynnika przejmowania ciepła w jego profilu...
-
Strength parameters of polyester reinforced PVC coated fabric after short term creep loading in biaxial mode
PublikacjaThis study addresses the analysis of tensile strength parameters of the technical fabric VALMEX, which is composed of two orthogonal polyester thread families (named the warp and fill) and both sides PVC coated. The material was firstly subjected to 48-hour biaxial creep loading with the equal stress level in both orthogonal directions of the fabric. The stress levels were established as follows: 4.6 kN/m, 10.4 kN/m, 16.4 kN/m,...
-
Determination of selected parameters/ analytes in surface water samples collected in the surroundings of the capital of Spitsbergen (Longyearbyen)
PublikacjaPolar regions are extremely sensitive to pollution such as harmful gases, particles or toxic substances which affect the Arctic climate and ecosystems. Spitsbergen, as well as all Arctic region, because of its geographically distant location and lack of industry sector, should be free of chemical pollution. Despite this, many pollutants could be found in the Polar environment, for example in freshwaters. Their occurrence is related...
-
Determination of selected chemical parameters in surface water samples collected from the Revelva catchment (Hornsund fjord, Svalbard)
PublikacjaSurface water samples (river and lake) were collected from the Revelva catchment every summer from 2010 to 2013. This study concerns importance of the use of some analytical techniques for pollutants and parameters deter- mination in Arctic environmental samples based on the example of total organic carbon, phenols, and formaldehyde determination and measurement of pH and electrical conductivity parameters. Significant...
-
The interaction parameters for solutions of n-butylurea in aqueous solutions of N-methylacetamide – The volumetric and compressibility studies between 288.15 K and 308.15 K
PublikacjaDensities and speed of sound were measured for solutions of n-butylurea in aqueous solution of Nmethylacetamide 2, 4, 6 and 8 (mol/kg) at T = (288.15, 298.15 and 308.15) K. From these data the apparent molar volumes, Vf, the apparent molar isentropic compressions, KSf, of the solute were determined. The concentration dependencies of the calculated quantities have been used to obtain the standard partial molar parameters. The latter...
-
Investigation of ecological parameters of a gas turbine combustion chamber with steam injection for the floating production, storage, and offloading vessel
PublikacjaThe article is dedicated to the investigation of the possibility of using the contact type gas turbine cycle with steam injection into the combustion chamber for the floating production, storage, and offloading vessel in order to increase the specific power and efficiency and reduce emissions of toxic components. A new approach is proposed, associated with the use of the two-stage injection of superheated steam into a gas turbine...
-
Rapid on-line method of wastewater parameters estimation by electronic nose for control and operating wastewater treatment plants toward Green Deal implementation
PublikacjaIn order to comply with legal regulations related to wastewater quality, the operational mode of facilities at wastewater treatment plant (WWTP) should be properly adjusted according to parameters of influents, however it is very difficult without frequently performed measurements. Currently there are known many techniques and devices for assesment of wastewater parameters such as chemical oxygen demand, biochemical oxygen demand,...
-
Influence of Added Water Mass on Ship Structure Vibration Parameters in Virtual and Real Conditions
PublikacjaModelling of ship structures in a virtual environment is now standard practice. Unfortunately, many engineers forget to consideri the influence of added water on the frequency values and the amplitude of natural vibrations. The article presents the effect of water damping on the frequency values of the individual natural vibration modes. The tests were carried out in two stages. First, the mentioned values were determined using...
-
Redundantly Actuated 3RRR Parallel Planar Manipulator - Numerical Analyses of its Dynamics Sensitivity on Modifications of its Platform’s Inertia Parameters
PublikacjaIn the paper, numerical analyses, as well as dynamics of a complex mechanism, are presented. Two objectives are crucial for the paper: inverse dynamic model is needed (dedicated to be use in the model predictive controller); an identification method is searched (some trajectory parameters are controlled, when specific trajectory is tracked under an open-loop model-based control), as selected parameters must be identified for the...
-
Determining the optimal filling of the surface with a linker with Universal Force Field and Reax Force Field
Dane BadawczeThe DataSet contains the atomic slabs of diamond surfaces with ATP molecules in water. The calculated data includes different sized surfaces from 90 Angstrom^2 to 691 Angstrom^2. Structures were relaxed using the Reax Force Field method with the Limited Memory Broyden–Fletcher–Goldfarb–Shanno algorithm. Structures were calculated with a convergence...
-
Artificial Neural Network based fatigue life assessment of riveted joints in AA2024 aluminum alloy plates and optimization of riveted joints parameters
PublikacjaThe objective of this paper is to provide the fatigue life of riveted joints in AA2024 aluminum alloy plates and optimization of riveted joints parameters. At first, the fatigue life of the riveted joints in AA2024 aluminum alloy plates is obtained by experimental tests. Then, an artificial neural network is applied to estimate the fatigue life of riveted lap joints based on the number of lateral and longitudinal holes, punch pressure,...
-
Dependence of bimolecular recombination rate constant on different experimental parameters
PublikacjaZ otrzymanych wzorów analitycznych oraz przeprowadzonych obliczeń numerycznych wynika, że dla wysokich natężeń pola elektrycznego stała szybkości rekombinacji bimolekularnej jest funkcją zewnętrznego pola elektrycznego oraz koncentracji nośników ładunku. Szczególnie interesujący jest wynik dotyczący obniżania się stałej szybkości rekombinacji wraz ze wzrostem natężenia pola elektrycznego, który różni się zupełnie od przewidywań...
-
Paraxial parameters and aberration of seven-electrode axisymmetric cathodic lens
Publikacja -
Hardware Implementation of Real Time Cavity Parameters Identification System
Publikacja -
Estimation of the parameters of the discrete model of a steel–concrete composite beam
Publikacja -
Influence of the use of ethanol fuel on selected parameters of the gasoline engine
Publikacja -
Robust Estimation of Integrated Hydraulics and Parameters in Water Distribution Systems
Publikacja -
The Effect of the Phenomenon of “Spectrum Leakage” on the Measurement of Power Quality Parameters
Publikacja -
Characteristics of Specialised Firefighter Clothing Used in Poland – the Thermal Parameters
Publikacja -
Variability of physico-chemical parameters in precipitation in Poland (1996-1999)
PublikacjaW publikacji przedstawiono wyniki badań przeprowadzonych w latach 1996-1999, dotyczących analizy próbek osadów atmosferycznych zebranych w trzech miejscach pobierania próbek. Zostały one porównane z wynikami otrzymanymi w pięciu innych miejscach na terenie Polski, rozmieszczonych zarówno na terenach objętych ochroną, takich jak parki narodowe, jak również narażonych na silny wpływ zanieczyszczeń pochodzących z aglomeracji miejskich...
-
Identification and validation of damage parameters for elasto-viscoplastic Chaboche model
PublikacjaArtykuł omawia procedurę identyfikacji parametrów zniszczenia w prawie Chabocha ze zniszczeniem. Proponowane podejście jest zilustrowane przykładami obliczeniowymi w programie MSC.Marc.
-
Performance of vibration surveillance in order to improve operating parameters of manipulators
PublikacjaPrzedstawiono nadzorowanie drgań układu nośnego manipulatora robota IRb-6. Do nadzorowania drgań zastosowano algorytm sterowania modalnego przy energetycznym wskaźniku jakości. Celem proponowanego algorytmu jest minimalizacja poziomu drgań końcówek manipulatora, i tym samym - zwiększenie możliwości nowoczesnych linii zrobotyzowanych, jak również dokładności i powtarzalności pozycjonowania robota.
-
Determination of selected parameters in a 1D open channel flow model
PublikacjaOkreślenie parametrów jest ważnym etapem tworzenia modelu matematycznego. W przypadku jednowymiarowego modelu przepływu ze swobodną powierzchnią opisanego układem równań de Saint-Venanta, jedną z grup parametrów wymagających identyfikacji są parametry związane z tarciem. Mogą one być określone w różny sposób, ale w większości przypadków problem ten stanowi zagadnienie żle postawione. W takich przypadkach najczęściej stosowaną...
-
Improvement of damage detection methods based on experimental modal parameters
PublikacjaW pracy przedstwiono sposoby porawy czułości metod detekcji uszkodzeń wykorzystujacych eksperyentalne parametry modalne konstrukcji. Wykazano, że zastosowanie zawansowanych technik obróbki sygnałów pomiarowych pozwala zdecydowanie poprwaić skutecznośc znanych z literatury metod.
-
Ifluence of geometrical and thermophysical parameters on two-phase thermosiphon performance
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych dotyczących wpływu geometrii pęku rur, rodzaju powierzni przejmowania ciepła parownika oraz płynu pośredniego na całkowitą wydajność dwufazowego termosyfonowego wymiennika ciepła (DTWC).
-
High accuracy hydroacoustic system to study codend model parameters
PublikacjaWażnym zadaniem projektantów narzędzi połowowych jest stworzenie efektywnych narzędzi połowowych działających selektywnie poprzez optymalizacje ich geometrii. Hydroakustyczny system pomiaru geometrii modeli worków dorszowych opisany w artykule został zaprojektowany dla opracowania konstrukcji worka dorszowego na potrzeby rybołówstwa na Morzu Bałtyckim.System składa się z 10 par przetworników ultradźwiękowych, mikroprocesorowego...
-
Measurement of engine and vehicle parameters using onboard CAN network
PublikacjaWspółczesne samochody wyposażane są w dużą liczbę układów elektronicznych, które wymagają wzajemnej wymiany informacji. Techniczne problemy niezależnego łączenia ze sobą dużej liczby sterowników doprowadziły do powstania pokładowych sieci wymiany danych. Do najpopularniejszych z nich zalicza się obecnie system CAN. W pracy przedstawiono metodę rozpoznawania ramek wiadomości transmitowanych w pokładowej sieci CAN pojazdu przez sterowniki....
-
Numerical Simulation of Operating Parameters of the Ground Source Heat Pump
Publikacja