Filtry
wszystkich: 1489
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: ionic liquids surface activity micelles formation phase transfer catalysis
-
Energy conversion in systems-contained laser irradiated metallic nanoparticles - comparison of results from analytical solutions and numerical methods
PublikacjaThis work introduces the theoretical method of metallic nanoparticles’ (NPs’) heat and mass transfer where the particles are coated on a surface (base), together with considering the case wherein nanoparticles move freely in a pipe. In order to simulate the heat transfer, energy and radiative transfer equations are adjusted to the considered issue. NPs’ properties are determined following the nanofluidic theories, whereas absorption...
-
The Use of Liquid Crystal Thermography in Selected Technical and Medical Applications—Recent Development
PublikacjaThermochromic liquid crystals (TLC) and true-colour digital image processing have been successfully used in non-intrusive technical, industrial and biomedical studies and applications. Thin coatings of TLC at surfaces are utilized to obtain detailed temperature distributions and heat transfer rates for steady or transient processes. Liquid crystals also can be used to make the temperature and velocity fields in liquids visible...
-
Thermal energy storage using stearic acid as PCM material
PublikacjaThis work presents an experimental study of thermal energy storage by use of PCM. The aim of the study was to establish the influence of different inlet temperature of heat transfer fluid (HTF) and different Reynolds number of HTF on intensity of charging process. The PCM used in this study was stearic acid and water was used as HTF. A copper helical coil mounted in cylindrical container served as a heat transfer surface.
-
Precipitation of calcium carbonate in the presence of rhamnolipids in alginate hydrogels as a model of biomineralization
PublikacjaThis paper reports the effects of rhamnolipids presence in the alginate hydrogel and CO32- solution, on the precipitation of CaCO3 in the Ca2+ loaded alginate hydrogel. Characteristics of the formed particles are discussed. Model conditions containing alginate hydrogel and rhamnolipids were used in order to mimic the natural environment of biomineralization in biofilms. It has been shown that rhamnolipids affect the characteristics...
-
Konzetrationslöschung durch Energieübertragung bei der Lumineszenz von Lösungen
PublikacjaThe absorption spectra and quantum yields of the fluorescence of rhodamine 6 G are investigated in two different water-glycerol mixtures as a function of the rhodamine concentration. The observed concentration quenching is attributed to the formation of rhodamine dimers and the decrease in quantum yield is compared with theoretical concepts about concentration quenching by energy transfer to the dimers.
-
Temperature of formation of Au nanostructures
Dane BadawczeNanostructures were obtained via annealing of thin Au films. In order to determine possible nanoislands formation mechanisms, dependence on initial film thickness was examined. For the surface morphology studies, nanograin structure and chemical composition analysis, SEM, HR TEM and EDS measurements were performed, respectively. Morphology studies shown...
-
Preparation and Characterization of Au/Pd Modified-TiO2 Photocatalysts for Phenol and Toluene Degradation under Visible Light—The Effect of Calcination Temperature
PublikacjaRutile loaded with Au/Pd nanoparticles was prepared using a water-in-oil microemulsion system of water/AOT/cyclohexane followed by calcination.Theeffect of calcination temperature (from350 to 700∘C) on the structure ofAu/Pd nanoparticles deposited at rutile matrix and the photocatalytic properties of Au/Pd-TiO2 was investigated in two model reactions (toluene degradation in gas phase and phenol degradation in aqueous phase). The...
-
Application of nanofluids in selected thermal technologies
PublikacjaSome peculiarities regarding convective heat transfer of nanofluids are presented. Particularly, results of the fundamental research concerning pool boiling and single phase convection of nanofluids as well as data obtained for selected heat exchangers operated with nanofluids are discussed.
-
Natural convective heat transfer from isothermalconic
PublikacjaTheoretical considerations on convective heat transfer from isothermal upward conicalsurfaces have been presented. The physical model of this phenomenon consists of an isothermalcone of inclination angle (φ) between the cone generating line (X) and the radius (R) of the cone base. The angle is a parameter of conical surface which varied from (φ = 0−circular horizontal plate) to (φ = π/2—vertical cylinder) . Onthe basis of Navier–Stokes...
-
The effect of gold shape and size on the properties and visiblelight-induced photoactivity of Au-TiO2
PublikacjatIn the present investigation, TiO2modified with a different geometry and size of gold particles, suchas nanospheres (NSPs), nanostars (NSTs) and nanorods (NRs), were prepared by the immobilizationmethod. The effect of the gold shape, size and TiO2matrix type (TiO2microspheres or rutile TIO-6 TiO2)were systematically investigated. The obtained photocatalysts were thoroughly characterized by UV–visdiffuse-reflectance spectroscopy...
-
Marcin Wekwejt dr inż.
OsobyMarcin Wekwejt, absolwent studiów inżynierskich w inż. biomedycznej (2016; Politechnika Bydgoska im. J. i J. Śniadeckich & Collegium Medicum im. L. Rydygiera), studiów magisterskich w inż. mechaniczno-medycznej (2018; Politechnika Gdańska & Gdański Uniwersytet Medyczny) oraz studiów doktoranckich w dyscyplinie inż. materiałowej (2021, Politechnika Gdańska). Uzyskał z wyróżnieniem stopień naukowy doktora nauk inżynieryjno-technicznych...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
Facet effect of TiO2 nanostructures from TiOF2 and their photocatalytic activity
PublikacjaIn this study, special attention is focused on the design of TiO2 morphology and microstructure in the two-step preparation procedure using TiOF2 as a precursor to study their photodegradation mineralization efficiency. Firstly, TiOF2 was synthesized by a simple solvothermal method using titanium(IV) tetrafluoride, which was further used as a precursor in preparation of anatase 2D nanosheets, octahedral, decahedral, and rectangular prisms...
-
Microfluidically Frequency-Reconfigurable Self-Quadruplexing Antenna Based on Substrate Integrated Square-Cavity
PublikacjaIn this article, a novel concept of self-quadruplexing tunable antenna (SQTA) enabled by microfluidic channels is investigated. The operating channels are either filled with air or dielectric liquids to enable frequency tunability. The proposed SQTA is implemented on the substrate-integrated square-cavity (SISC). A swastika-shaped slot is milled on the top-surface of the SISC to create four quarter-mode resonators. The resonators...
-
Searching for Solvents with an Increased Carbon Dioxide Solubility Using Multivariate Statistics
PublikacjaIonic liquids (ILs) are used in various fields of chemistry. One of them is CO2 capture, a process that is quite well described. The solubility of CO2 in ILs can be used as a model to investigate gas absorption processes. The aim is to find the relationships between the solubility of CO2 and other variables—physicochemical properties and parameters related to greenness. In this study, 12 variables are used to describe a dataset...
-
Effect of pulse laser treatment at different process variables on mechanical behavior of carbon nanotubes electrophoretically deposited on titanium alloy
PublikacjaPurpose: Titanium and its alloys are widely used as biomaterials for long-term implants, but they are usually surface-modified due to their weak bioactivity and wear resistance. Laser processing was used to modify the surface layer, and elemental carbon was a component of the deposited coatings. This research aims to use a combination of both methods based on preliminary electrophoretic deposition of multi-wall carbon nanotubes...
-
Application of nanofluids in thermal technologies
PublikacjaNanofluids it is a relatively new category of thermal fluids that can serve as coolants, both in single- and two phase systems. However application of nanofluids in industrial applications requires faultless their thermophysical properties. Existing models originally developed for liquid/solid particles mixtures (slurries) fail in case of nanofluids. Moreover correlations used to calcuate heat transfer coefficients of conventional...
-
SEMG signal database for the automated upper limb rehabilitation process
Dane BadawczeAn automated rehabilitation device control system requires information about the patient's physiological condition. This is possible thanks to the use of biological feedback in the form of electromyography and surface signals (Surface Electromyography, SEMG).
-
Proton transfer reactions for ionized water clusters
PublikacjaCalculations of formation energies of the ionized water clusters and energies of reactions between small (including less than eight water molecules) neutral and positively ionized water clusters are presented. Moreover, we discuss some reaction paths between neutral and positively charged dimers, trimers and tetramers and proton transfer reactions (PTR) between cyclic clusters and H3O+ ions which can appear in beam experiments...
-
Influence of the ionic strength on the amyloid fibrillogenesis of hen egg white lysozyme
PublikacjaThe study investigates the role of the electrostatic interactions in the fibrillation of the hen egg white lysozyme (HEWL). In order to achieve this aim the influence of the cations Na+, Mg2+ and Al3+ on the amyloid fibril formation and amorphous aggregation was tested. The amyloids are formed in the solution without added salt but the Thioflavin T fluorescence gives the false-negative result. In these conditions, the HEWL fibrils...
-
Visible light photoactivity of TiO2loaded with monometallic(Au or Pt) and bimetallic (Au/Pt) nanoparticles
PublikacjaTiO2modified with monometallic (Au or Pt) and bimetallic (Au/Pt) nanoparticles have been preparedusing a water-in-oil microemulsion system (water/AOT/cyclohexane) followed by calcination step. Theeffect of metal ratio, reducing agent type (NaBH4or N2H4), TiO2matrix type (P-25, ST-01, TiO-5, TiO2nano-tubes or TiO2obtained by TIP hydrolysis) as well as calcination temperature (from 350 to 650◦C) weresystematically investigated. Obtained...
-
CO2 Separation Using Supported Deep Eutectic Liquid Membranes Based on 1,2-propanediol
PublikacjaIn this work, deep eutectic solvents (DESs) composed of choline chloride, acetylcholine chloride or tetrabutylammonium chloride, and 1,2-propanediol were used as a liquid phase for polypropylene-based supported liquid membranes (SLMs) and evaluated for the separation of carbon dioxide from CO2/N2 mixtures. Fourier transform infrared spectra were obtained to confirm DES formation, and the thermal stability of solvents was investigated...
-
The Effect of Laser Re-Solidification on Microstructure and Photo-Electrochemical Properties of Fe-Decorated TiO2 Nanotubes
PublikacjaFossil fuels became increasingly unpleasant energy source due to their negative impact on the environment; thus, attractiveness of renewable, and especially solar energy, is growing worldwide. Among others, the research is focused on smart combination of simple compounds towards formation of the photoactive materials. Following that, our work concerns the optimized manipulation of laser light coupled with the iron sputtering to...
-
Studies on applicability of new solid-phase microextraction and determination of short - chain monocarboxylic acids
PublikacjaA convenient approach to monitor the short-chain monocaroboksylic acids (SCAMs) in different samples is gas chromatography (GC) preceded by sample preparation based on solid-phase microextraction (SPME). The fiber with polar coatings were used to extract the SCAMs from headspace of liquid and solid samples. Recently polimeric ionic liquid (PIL) fiber coatings have been proposed to extract volatile organic compounds, minly polar...
-
Separation of Volatile Oxygen-containing Organic Compounds by Gas Chromatography - selectivity comparison of different polarity stationary phases
PublikacjaThis paper present a results of the separation of 36 reference compounds belonging to the group of Volatile Oxygen-Containing Organic Compounds (OVOCs) using capillary gas chromatography with flame ionization detector (GC-FID) and three stationary phases of different polarity. A selectivity has been studied regarding to OVOCs and n -alkanes. The most useful for the separation of the group OVOCs is a polar ionic liquid stationary...
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublikacjaIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...
-
Spinning Fluids Reactor: A new design of a gas – liquid contactor
PublikacjaCurrent trends in chemical reactor design are based on adapting these to the requirements of a particular chemical process. Processes involving reactions between the gas and liquid phase in particular require precise adjustment of all parameters. The common denominator for most modern design solutions is enhancement of the mass transfer area and the overall volumetric mass transfer coefficient. Gas – liquid contactors evolved from...
-
Dew Formation and Chemistry Near a Motorway in Poland
PublikacjaIn this study, the influence of traffic intensity on dewformation efficiency and chemistry is presented. The measurementswere conducted near the A4 motorway in SW Poland in almost flatland relief with intense agricultural activity. The dew/hoarfrost wascollected by means of insulated plain passive radiative condensersat three sites: AN and AS located in the close vicinity of themotorway (30 m) on the opposite sides of the road,...
-
Scanning electron microscopy (SEM) images of boron-doped diamond thin films at poly(lactic acid)
Dane BadawczeThe dataset contains the photos obtained by scanning electron microscope(SEM), revealing the surface morphology and cross-section of boron-doped diamond electrodes on commercially available graphene-doped polylactide acid. The boron doping level expressed as the [B]/[C] ratio in the gas phase for these studies was 500 and 10,000 ppm. The top views of...
-
Fluorescence of nanodiamond cocktails: pH-induced effects through interactions with comestible liquids
PublikacjaFluorescent nanodiamonds with nitrogen-vacancy centers have become important nanoscale probes for sensing and imaging. The surface chemistry of the nanodiamonds influences their emission, interactions, and quantum properties. In this work, we propose to utilize fluorescent nanodiamonds as photostable markers for investigation of comestible liquids. We prepared nanodiamond/comestibles suspensions/cocktails with a wide range of pH...
-
CO2 capture using steam ejector condenser under electro hydrodynamic actuator with non-condensable gas and cyclone separator: A numerical study
PublikacjaThe concept for condensation of steam and CO2 separation in a negative CO2 emission gas power plant involves the utilization of a steam ejector condenser (SEC) for direct-contact condensation of vapor with inert gas (CO2) on a spray of subcooled liquid, integrated with a separator to produce pure CO2. Due to the increasing diffusion resistance and reduced convective heat transfer between the steam and subcooled water phases...
-
Mikropompa elektrohydrodynamiczna na ciecz dielektryczną zasilana napięciem stałym
PublikacjaW niniejszym artykule zaprezentowano projekt i działanie miniaturowej pompy elektrohydrodynamicznej (EHD) zasilanej napięciem stałym przeznaczonej do chłodzenia elementów elektronicznych. Zmierzono natężenie przepływu cieczy oraz ciśnienie wytwarzane przez pracującą mikropompę. Maksymalne natężenie przepływu, 0,5 ml/min, uzyskano dla napięcia 12 kV. Zmierzone ciśnienie wyniosło 500 Pa przy przyłożonym napięciu 6 kV. Maksymalny...
-
Automated Design of Linear Phase Filters
PublikacjaThis paper presents a fast technique for an automated design of microwave filters with linear phase. The proposed method exploits the cost function defined using the location of complex zeros and poles of the filter’s transfer and reflection function. The effectiveness of the proposed technique is presented with two illustrative examples.
-
An evaluation of sucrose as a possible contaminant in e-liquids for electronic cigarettes by hydrophilic interaction liquid chromatography–tandem mass spectrometry
PublikacjaThe influence of sucrose combustion products on smoking and nicotine addiction is still controversial because the presence of the sucrose may be treated as a source of aldehydes and organic acids. In e-liquids used as refills for electronic cigarettes, which are made primarily of poly(propylene glycol), glycerine and ethanol, sucrose may be present at trace levels, and its impact on mainstream smoke formation, and hence on human...
-
Photocatalytic and Antimicrobial Properties of Ag2O/TiO2 Heterojunction
PublikacjaAg2O/TiO2 heterojunctions were prepared by a simple method, i.e., the grinding of argentous oxide with six different titania photocatalysts. The physicochemical properties of the obtained photocatalysts were characterized by diffuse-reflectance spectroscopy (DRS), X-ray powder diffraction (XRD) and scanning transmission electron microscopy (STEM) with an energy dispersive X-ray spectroscopy (EDS). The photocatalytic activity was...
-
Studies of the mechanism of metal metal dusting of 10CrMo9-10 steel after 10 years of operation in trhe semi-regenerative catalytic reformer
PublikacjaThe study showed that metal dusting mechanism of 10CrMo9-10 steel operated in industrial environment differs from models developed in laboratories. Significant differences lie in the fact that the models developed in laboratories only assume the formation of metastable carbide M3C, while studies have shown that the formation of M3C carbides is associated with the transformation of primary carbides and in the next stage is preceded...
-
Self-Organized Nanotubular Oxide Layers on Ti and Ti Alloys
PublikacjaTo improve bioactivity of titanium and titanium, the implant surface modification by formation of self-organized TiO2 nanotube arrays with electrochemical techniques is presented. The influence of electrolyte composition and deposition parameters during anodization is characterized. The enhancement of phosphates deposition by titanium nanotubular structure is discussed. The calcium phosphate ceramics is shown to be uniformly deposited...
-
Oxidation and hydrogen behavior in Zr-2Mn alloy
PublikacjaThe purpose of the present research was to determine the oxidation and hydrogenation behavior in the new Zr-2Mn alloy. The oxidation of alloy was performed at temperatures between 350°C and 900°C for 30 minutes. The hydrogen charging was made for 72 h at a current density 80 mA/cm2. The charged samples were heat treated at 400°C for 4 h to obtain a uniform hydrogen profile content across the sample. The oxidation resulted in an...
-
Studies on the formation of formaldehyde during 2-ethylhexyl 4-(dimethylamino)benzoate demethylation in the presence of reactive oxygen and chlorine species
PublikacjaIn order to protect the skin from UV radiation, personal care products (PCPS) often contain chemical UV-filters. These compounds can enter the environment causing serious consequences on the water ecosystems. The aim of this study was to examine, the effect of different factors, such as UV light, the presence of NaOCl and H2O2 on the formaldehyde formation during popular UV filter, 2-ethylhexyl 4-(dimethylamino)benzoate (ODPABA)...
-
The effect of microemulsion composition on the morphology of Pd nanoparticles deposited at the surface of TiO2 and photoactivity of Pd-TiO2
PublikacjaA series of microemulsion (ME) system, constituted by different water to surfactant molar ratios (Wo) and oil to surfactant mass ratios (S), have been applied for Pd-TiO2 preparation. The effect of ME properties on the morphology of Pd nanoparticles formed at TiO2 surface and an effect of Pd size and distribution on the surface and photocatalytic properties of Pd-TiO2 were investigated. Microemulsion systems were characterized...
-
Randomly Functionalized Polyethylenes: In Quest of Avoiding Catalyst Deactivation
PublikacjaWell-defined randomly functionalized polyolefins produced by catalysis form an interesting class of polymers with great potential for various applications. One of the major challenges for the production of these materials forms the incompatibility of the commonly used electrophilic group 4 metal based catalysts and the desired nucleophilic, especially protic functionalities like hydroxyl and carboxylic acid groups. Although pacification...
-
Substrate Dependence in the Formation of Au Nanoislands for Plasmonic Platform Application
PublikacjaIn this work, the influence of the various substrates on Au nanoisland formation has been studied. Nanostructures were obtained via annealing of thin Au films. In order to determine nanoisland formation mechanisms, correlation between an initial film thickness and temperature of formation, shapes, and dimensions of nanostructures was examined. For the surface morphology studies, nanograin structure, and chemical composition analysis,...
-
Identification of antigen Ag43 in uropathogenic Escherichia coli Dr+ strains and defining its role in the pathogenesis of urinary tract infections
PublikacjaUrinary tract infections (UTIs) caused by uropathogenic Escherichia coli (UPEC) are among the most common bacterial infectious diseases in the developed world. The urovirulence of UPEC is mainly associated with the surface-exposed fimbrial adhesins and adhesins of the autotransporter (AT) family. The best studied of theses proteins is antigen 43 (Ag43) mediating cell aggregation, adhesion and biofilm development as the causes of...
-
The effect of nanoparticles size on photocatalytic and antimicrobial properties of Ag-Pt/TiO2 photocatalysts
PublikacjaAg-Pt-modified TiO2 nanocomposites were synthesized using the sol–gel method. Bimetallic modified TiO2 nanoparticles exhibited improved photocatalytic activity under visible-light irradiation, better than monometallic Ag/TiO2 and Pt/TiO2 nanoparticles (NPs). All modified powders showed localized surface plasmon resonance (LSPR) in visible region. The photocatalysts’ characteristics by X-ray diffractometry (XRD), scanning transmission...
-
Helium-assisted, solvent-free electro-activation of 3D printed conductive carbon-polylactide electrodes
PublikacjaFused filament fabrication is one of the most rapidly developing 3D printing techniques, with numerous applications, including in the field of applied electrochemistry. Here, the utilisation of conductive carbon black polylactic acid (CB-PLA) for 3D printouts is the most promising. To use CB-PLA as an electrode material, an activation process must be performed, removing the polymer matrix and uncovering the electrically conductive...
-
Wpływ wybranych parametrów środowiska na przebieg degradacji rur okładzinowych ze stali P110
PublikacjaMateriały używane na orurowanie odwiertów w poszukiwaniu i wydobyciu ropy i gazu poddawane są niekorzystnym warunkom eksploatacji takich jak: podwyższona temperatura, wysokie ciśnienie, turbulentny przepływ korozyjnych cieczy z zawieszonymi cząstkami stałymi. Jednym z gatunków stali używanych do produkcji rur okładzinowych jest stal P110 (za normą API 5CT) będąca stalą średnio-węglową, niskostopową o wysokiej wytrzymałości. Celem...
-
Photophysics and Halide Quenching of Soret-excited ZnTPPS4- in Aqueous Media
PublikacjaSteady state S2-S0 and S1-S0 absorption and emission spectra and picosecond S2 decay and S1 fluorescence rise times have been measured for the model porphyrin ZnTPPS4− in water and in aqueous iodide solutions of constant ionic strength. The dynamics of S1 quenching by iodide are well-modeled by a Stern-Volmer mechanism yielding kQ = 1.75 × 109 M−1 s−1. The S2 state is quenched on a ps time scale by a static electron-transfer mechanism...
-
Novel two-step synthesis method of thin film heterojunction of BiOBr/Bi2WO6 with improved visible-light-driven photocatalytic activity
PublikacjaA novel two-step ionic liquid assisted procedure was applied for a controllable synthesis of BiOBr/Bi2WO6 heterojunction thin films. The preparation route involved an anodic oxidation of tungsten foil and hydrothermal transformation of as-anodized oxide in the presence of bismuth precursor and ionic liquid, N-butylpyridinium bromide [BPy][Br]. The BiOBr plates with irregular shapes adhered to the surface of flower-like Bi2WO6 and...
-
Perspectives on the replacement of harmful organic solvents in analytical methodologies: a framework toward the implementation of a generation of eco-friendly alternatives
PublikacjaVolatile organic solvents derived from non-renewable fossil feedstocks are commonplace in analytical laboratories. In spite of their convenient performance in countless unit operations, their environmental, health and safety issues represent a major area of concern. The progressive replacement of organic solvents obtained from fossil resources by eco-friendly alternatives would involve remarkable advances within the framework of...
-
Investigation of functional layers of solid oxide fuel cell anodes for synthetic biogas reforming
PublikacjaSolid oxide fuel cells (SOFCs) are one of the most promising energy conversion devices due to their high efficiency, low pollution and fuel flexibility. Unfortunately, when hydrocarbons are used as a fuel, for example in the form of a biogas, solid carbon can deposit on the anode surface. This process leads to the degradation of the fuel cell performance. A possible solution to this problem is to apply an additional catalytic material,...