Wyszukiwarka
Wyniki wyszukiwania dla: electric field
-
Tyre rolling resistance and its influence on fuel consumption
PublikacjaRolling resistance of tyres is one of the major resistive forces acting on any wheeled vehicle. Unfortunately, it is also one of the forces very difficult to measure. It is estimated that in certain traffic conditions (like for example constant speed driving with slow or moderate speed) so called Rolling Resistance Impact Factor may be as high as 0.3. This means that reduction of rolling resistance by 50% would lead to 15% of energy...
-
Comparison of state feedback and PID control of pressurizer water level in nuclear power plant
PublikacjaThe pressurizer water level control system in nuclear power plant with pressurized water reactor (PWR) is responsible for coolant mass balance. The main control goal is to stabilize the water level at a reference value and to suppress the effect of time-varying disturbances (e.g. coolant leakage in primary circuit pipeline system). In the process of PWR power plant operation incorrect water level may disturb pressure control or...
-
Experimental bases for the rail track surface damage detection system
PublikacjaA diagnosis of rail surface is generally based on the classical method of direct assessment and track geometry measurements. Identification and qualification of inequality and damage on the surface rails is depend on the skills and experience person who conducting inspection. In times of increasing exploitation of railways, infrastructure managers decide to use systems supporting the assessment of technical condition of the railways....
-
Synchronous generator model taking into account the non-uniform saturation of the pole shoes
PublikacjaFor the evaluation of modern electric power systems with regard to their behavior, weight, and reliability a novel modeling and simulation tools have been developed. The paper presents circuit model of synchronous generator taking into account both the non-sinusoidal distribution of the stator and rotor winding, and non-uniform saturation of the pole shoes. This model is suitable for simulation of both salient and no-salient pole...
-
Study on effective front region thickness of PCM in thermal energy storage using a novel semi-theoretical model
PublikacjaThermal energy storage in mobile applications, particularly battery of electric vehicles, is currently gaining a lot of importance. In this paper, a semi-theoretical time-dependent mathematical model of the phase change in a double shell thermal energy storage module has been developed where the inner tube is a heat exchange surface. An effective front region thickness for the melting and solidification process has been studied....
-
Unidirectional DC/DC Converter with Voltage Inverter for Fast Charging of Electric Vehicle Batteries
PublikacjaThe paper proposes the adaptation of the industrial plant’s power network to supply electric vehicle (EV) fast-charging converters (above 300 kW) using renewable energy sources (RESs). A 600 V DC microgrid was used to supply energy from RESs for the needs of variable speed motor drives and charging of EV batteries. It has been shown that it is possible to support the supply of drive voltage frequency converters (VFCs) and charging...
-
Fault Loop Impedance Measurement in Circuits Fed by UPS and Principle of Safety Protection
PublikacjaThis paper indicates a significant problem of uncertainty of fault loop impedance (FLI) measurement in circuits powered from uninterruptible power supply (UPS) (double-conversion AC-DC-AC). The correctly determined value of this impedance, related to the short-circuit current disconnection time and to the reference value, is one of the most important elements that determines the approval of an electrical installation and its receivers...
-
Verification of safety in low-voltage power systems without nuisance tripping of residual current devices
PublikacjaLow-voltage power systems require initial and periodical verification to check the effectiveness of protection against electric shock. As a protection in case of fault, automatic disconnection of supply is most often used. To verify such a protection measure, the earth fault loop impedance or resistance is measured. This measurement is easy to perform in circuits without residual current devices. When residual current devices are...
-
Lighting education for architects, the barriers and challenges: a survey of architecture students
PublikacjaCreating a well-lit environment requires the understanding of daylight and electric lighting design principles within the built environment. Recent years have brought a large number of new lighting assessment and design methods. The discovery of new photoreceptor cells in the eye - photosensitive retinal ganglion cells - forced lighting researchers to focus on parametrisation for the image forming (IF) and non-image forming (NIF)...
-
Practical Eco-Driving Strategy for Suburban Electric Multiple Unit
PublikacjaIn this paper, a practical approach to velocity profile optimization for electric multiple unit was presented. The study focuses on a case of fast urban railway, which is a popular mean of transport across Tricity, Poland. Based on observations and measurements, a potential for improvement of energy efficiency by modifying the speed profile was recognized. In order to conduct necessary calculations, simulation model of railway...
-
Novel Cold Crucible Ultrasonic Atomization Powder Production Method for 3D Printing
Publikacja: A new powder production method has been developed to speed up the search for novel alloys for additive manufacturing. The technique involves an ultrasonically agitated cold crucible installed at the top of a 20 kHz ultrasonic sonotrode. The material is melted with an electric arc and undergoes pulverization with standing wave vibrations. Several different alloys in various forms, including noble and metallic glass alloys, were...
-
Interdependence between Power Grids and Communication Networks: A Resilience Perspective
PublikacjaPower network resilience is increasingly dependent on communication networks. Besides traditional generation, power networks need to accommodate increasingly high penetration levels of dispersed micro generation, mostly based on renewable sources, and increasing and challenging demand, such as electric vehicles. At the same time the deployment of enabling technologies throughout the power grid makes available new demand resources...
-
Analysis of Induced Voltages and Power Losses in High Voltage Power Cables for Selected Methods of Cables Sheaths Bonding
PublikacjaPower is increasingly supplied to city centres with 110 kV cable lines. This is a convenient way to supply power, and practically the only one possible in areas of dense urban development. A high-voltage cable contains a coaxial metallic sheath, in which in normal operation and in fault conditions (during short-circuits) significant line-to-earth voltages can be induced, which threatens electric shock and/or damage to the cable’s...
-
Evaluation of fire hazard in electrical installations due to unfavorable ambient thermal conditions
PublikacjaEvaluation of fire hazard caused by electrical installations is a difficult and important topic, and it limits the possibility of loss of life or health of people, as well as the occurrence of significant property damage. In particular, this hazard was caused by power cables and especially photovoltaic (PV) installations. The authors proved that power cables directly exposed to strong solar radiation are likely to exceed maximum...
-
Buried Object Characterization Using Ground Penetrating Radar Assisted by Data-Driven Surrogate-Models
PublikacjaThis work addresses artificial-intelligence-based buried object characterization using 3-D full-wave electromagnetic simulations of a ground penetrating radar (GPR). The task is to characterize cylindrical shape, perfectly electric conductor (PEC) object buried in various dispersive soil media, and in different positions. The main contributions of this work are (i) development of a fast and accurate data driven surrogate modeling...
-
Space vector modulation in multilevel inverters of the servo drives of the trajectory measurements telescopes
PublikacjaUsing the MatLab/Simulink mathematical model of a three-phase three-level voltage inverter, the influence of the space-vector modulation (SVM) algorithm on the pulsations of the current (torque) of an AC motor in the range of low rotation speeds is considered. It is shown that the SVM of the second kind does not provide a pulsations level comparable to the pulsations of a sinusoidal pulse-width modulation (SPWM), both in the static...
-
Designing high-performance asymmetric and hybrid energy devices via merging supercapacitive/pseudopcapacitive and Li-ion battery type electrodes
PublikacjaWe report a strategic development of asymmetric (supercapacitive–pseudocapacitive) and hybrid (supercapacitive/pseudocapacitive–battery) energy device architectures as generation–II electrochemical energy systems. We derived performance-potential estimation regarding the specific power, specific energy, and fast charge–discharge cyclic capability. Among the conceived group, pseudocapacitor–battery hybrid device is constructed with...
-
Literature review of user needs, toward user requirements
PublikacjaThis report has been developed in the frame of the IEA SHC Task 61 Subtask A “User requirements”. The main objective was to rethink and reformulate user requirements to lighting (daylighting and electric lighting) in public buildings on the basis of a thorough literature study. The work is a joint effort of a number of scientists and represents collective knowledge in this topic. The concept of Lighting quality is the one, among...
-
Estimation of zero buoyancy of the batyscaphe. Pneumatic buoyancy control of the bathyscaphe
PublikacjaThe subjects of this work are matters concerning the batyscaphe designed and constructed by the Scientific Circle of Young Constructors (SCoYC) acting at the Faculty of Technical Sciences of the Olsztyn University of Warmia and Mazury.The goal od the remote-controlled batyscaphe is an underwater exploration of water resorvoirs in Poland. Design and construction of the unmanned watercraft, also known as a batyscaphe, required the...
-
EXPERIMENTAL RESEARCH ON INFLUENCE OF THE FUEL NOZZLE GEOMETRY ON THE FUEL CONSUMPTION OF THE MARINE 4-STROKE DIESEL ENGINE
PublikacjaThe article presents experimental research that has been carried out on a marine, 4-stroke, 3-cylinder, turbocharged engine. During testing, the engine operated at a constant rotational speed of 750 rpm and a load from 0 kW to 280 kW. The engine was fuelled by diesel oil of known specification and loaded by electric generator with water resistance. The fuel consumption was measured during the engine operation with fuel nozzles...
-
Properties of LiMnBO3 glasses and nanostructured glass-ceramics
PublikacjaPolycrystalline LiMnBO3 is a promising cathode material for Li-ion batteries. In this work, we investigated the thermal, structural and electrical properties of glassy and nanocrystallized materials having the same chemical composition. The original glass was obtained via a standard melt-quenching method. SEM and 7Li solid-state NMR indicate that it contains a mixture of two distinct glassy phases. The results suggest that the...
-
Magnetic-dipole-to-electric-quadrupole cross-susceptibilities for relativistic hydrogenlike atoms in some low-lying discrete energy eigenstates
PublikacjaIn this paper we present tabulated data for magnetic-dipole-to-electric-quadrupole cross-susceptibilities (χ_{M1→E2}) for Dirac one-electron atoms with a pointlike, spinless and motionless nucleus of charge Ze. Numerical values of this susceptibility for the hydrogen atom (Z = 1) and for hydrogenic ions with 2 \leqslant Z \leqslant 137 are computed from the general analytical formula, recently derived by us (Stefanska, 2016), valid...
-
Przekształtnik prądu jako sterownik w układach napędowych z silnikami indukcyjnymi
PublikacjaThe circuits used for power conversion applied in drives with electric machines are classified into two groups: voltage source inverters (VSI) and current source inverters (CSI). Application of the current source inverter results in better properties of drive than application of voltage source inverter because there is no output filter. The development of power electronics and especially the IGBTs, in which on/off-times are very...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a micro-turbine for a co-generation micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attention was...
-
Implementation of power transformer controlled switching algorithm
PublikacjaThe article presents two new algorithms of controlled switching the power transformer. The main aim of the paper is to obtain formulas that determine the moments of closing of the circuit breaker poles. The study contains projects of control systems for both algorithms. Mathematical formulas for the time instants of the breaker poles closing were developed on the basis of electric circuit theory and magnetic circuit theory. The...
-
Experimental test results of an automatic voltage regulator with independent phase voltage controllers
PublikacjaThe growing number of distributed renewable energy sources and dynamic constant-power loads (e.g. electric vehicle charging stations) pose new challenges for network operators. These changes result in alterations to network load profiles and load flows, leading to greater voltage volatility. One effective solution to these problems can be the use of automatic voltage regulators (AVRs), which stabilize and symmetrize voltage output,...
-
Partially Isolated Multi-Active Bridge DC-DC Converter with Bidirectional EV Charging Ports
PublikacjaThere is a growing interest in multiport converters due to their ability to interconnect various energy sources and loads using reduced number of components. Regarding electric vehicle (EV) chargers connection, existing multiport solutions either lack scalability, featuring only one isolated charging port or the operation of ports depend on each other, complicating the converter control algorithm. This article proposes a partially...
-
The pulse width modulation strategy for a five-phase three-level NPC voltage source inverter with DC-link voltage balancing ability
PublikacjaThe doctoral dissertation is all about the development of the space vector modulation algorithm for controlling the generation of output voltage vectors in a three-level, five-phase NPC inverter. The developed algorithm can be used to control five-phase motors, where it will be possible to increase the motor torque by 15%; by appropriate injection of 3rd harmonic current. The proposed control approach also opens up the possibility...
-
Modeling of low calorific gas burning in a deficient oxygen environment and high-temperature oxidizer
PublikacjaThe experimental research will be performed using the experimental facility with a combustion chamber. The oxygen concentration in combustion oxidizers will be varied from 21% by volume (normal) air to 2%. The test combustion chamber will be fed with propane or methane as the reference fuel, then with low calorific fuels as test gases obtained by mixing various combustible components, e.g. H2, CH4, CO, and neutral gases, e.g. N2,...
-
Engineering education for smart grid systems in the quasi-industrial environment of the LINTE^2 laboratory
PublikacjaSmart grid systems are revolutionising the electric power sector, integrating advanced technologies to enhance efficiency, reliability and sustainability. It is important for higher education to equip the prospective smart grid professional with the competencies enabling them to navigate through the related complexities and drive innovation. To achieve this, interdisciplinary education programmes are necessary, addressing inter...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a microturbine for a cogeneration micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3 kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attentionwas paid...
-
The Influence of LED Lighting Sources on the Nature of Power Factor
PublikacjaThis article presents measurements of electric power absorbed by a newly built facility for office and scientific research activities. These measurements highlighted the need for compensation of capacitive reactive power—not predicted by the designer—due to the vast use of LED lighting in the facility. The article also describes a reactive power compensation system, designed on the basis of the above-mentioned measurements, and...
-
Modeling of a Quasi-Resonant DC Link Inverter Dedicated to Common-Mode Voltage and Ground Current Reduction
PublikacjaIn this paper, the modeling methodology of the AC drive system with a Parallel Quasi-Resonant DC Link Inverter (PQRDCLI) is described. A presented modeling approach is an attractive tool used for the effective evaluation of a common-mode (CM) voltage and grounds current reduction methods. Designed models of inverter, induction machine (IM), and cable are simple, thus the methods for parameter extraction are not complicated. Verification...
-
Analysis of the regenerative braking process for the urban traffic conditions
PublikacjaIn a regular drive system, with an internal combustion engine, vehicle braking is connected with the unproductive dissipation of kinetic and potential energy accumulated in the mass of the vehicle into the environment. This energy can constitute up to 70% of the energy used to drive a vehicle under urban conditions. Its recovery and reuse is one of the basic advantages of hybrid and electric vehicles. Modern traffic management...
-
Piezoresponse force microscopy and dielectric spectroscopy study of Ba0.6Sr0.4TiO3 thin films
PublikacjaResearch on synthesis, characterization and determination of processing – structure – property relationships of commercially important ferroelectric thin films has been performed. The sol-gel-type solution deposition technique was applied to produce good quality thin films of Ba0.6Sr0.4TiO3 (BST60/40) chemical composition on the stainless steel substrates. The thin films were characterized in terms of their microstructure, crystal...
-
Electric and magnetic properties of Lanthanum Barium Cobaltite
PublikacjaThe cubic Ba0.5La0.5CoO3‐δ was synthesized using solid state reaction. The structural properties were determined by the simultaneous refinement of Synchrotron Powder X‐ray Diffraction and Neutron Powder Diffraction data. Iodometric titration was used to examine the oxygen stoichiometry and average cobalt oxidation state. Low‐temperature magnetic studies show soft ferromagnetic character of fully oxidized material, with θP = 198(3)...
-
Mg2+ Doping Effects on the Structural and Dielectric Properties of CaCu3Ti4O12 Ceramics Obtained by Mechanochemical Synthesis
PublikacjaIn this study, ceramic CaCu3Ti4O12 (CCTO) and CaCu3−xMgxTi4O12 solid solutions in which 0.1 ≤ x ≤ 0.5 were prepared by the mechanochemical method, realized by a high‐energy ball milling technique. The effects of the Mg2+ ion concentration and sintering time on the dielectric response in the prepared ceramics were investigated and discussed. It was demonstrated that, by the use of a sufficiently high energy of mechanochemical treatment,...
-
The Impact of Thermal Stresses on Volume Resistivity: Performance Comparison between TR-XLPE and XLPE Cables
PublikacjaMost failures in electric power cables are attributed to the development of water trees inside the insulating materials. Thus, the development and utilization of Tree Retardant Cross-Linked Polyethylene (TR-XLPE) based cables have recently been given great attention to overcome the treeing issues. TR-XLPE cables use low-density polyethylene compounds suppressing the formation of water trees while retaining excellent electrical,...
-
Estimation of Vehicle Energy Consumption at Intersections Using Microscopic Traffic Models
PublikacjaThis paper addresses issues related to modeling energy consumption and emissions using microscopic traffic simulations. This paper develops a method in which a traffic model is used to calculate the energy needed to travel through selected types of intersections. This paper focuses on energy consumption and derived values of calculated energy, which can be, for example, carbon dioxide emissions. The authors present a review of...
-
Polymer Materials for U-Shaped Optic Fiber Sensors: A Review
PublikacjaFiber optic sensors have gained popularity over the last few decades. This is due to their numerous advantages, such as good metrological parameters, biocompatibility and resistance to magnetic and electric fields and environmental pollution. However, those built from glass fiber have one main disadvantage—they are fragile, meaning they can be easily damaged, even by the presence of vibration. Due to the great progress made by...
-
A Miniaturized and High Optically Transparent Frequency Selective Surface for RF Shielding using Double-Glazed Glass Windows for Green Building Applications
PublikacjaThis research presents a miniaturized and high optically transparent (OT) frequency selective surface (FSS) for achieving RF shielding through glass window panels. The proposed FSS consists of a single-layered copper pattern sandwiched between two ordinary glass substrates to suppress the dual bands of sub-6 fifth generation (5G). In particular, the design effectively shields n65-downlink (2.1 GHz) and a portion of n78-band (3.5...
-
Topography and microstructure of phosphate-iron glasses containing niobium and titanium
Dane BadawczeThe topography and microstructure of phosphate-iron glasses containing niobium and titanium were investigated by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM). Glass samples of the composition of 35P2O5-30Fe2O3-(35-x)Nb2O5-xTiO2 where x= 0; 7.5 and 15 (in %mol) were prepared by the conventional melt quenching technique. Appropriate...
-
The power spectral density of audible noise and electric disturbances in ship’s electrical drive systems with frequency converters
Dane BadawczeThe presented dataset is part of research focusing on the impact of the ship's electrical drive systems with frequency converters on vibrations and the level of audible noise on ships.
-
Temperature influence on tire/road noise evaluated by the drum method
PublikacjaAmbient air and road surface temperatures substantially affect the road vehicle noise emission. The temperature influence on tire/road noise depends mainly on tire-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tires. The correction procedures for temperature effect are still under consideration and preparation. Laboratory experiment was prepared to...
-
The Review of the Selected Challenges for an Incorporation of Daylight Assessment Methods into Urban Planning in Poland
PublikacjaThe main objectives of this research it to find out if modern daylight assessment and design methods can be useful for urban residential planning in Poland. The study gives a chance to describe and appraise modern daylight design techniques. The other purpose is to illustrate how daylight knowledge could be used as an incentive to rethink the way urban environments are created. Although daylight design is acknowledged in literature...
-
Public Lighting in a Context of Regeneration Processes in Polish Cities
PublikacjaThe purpose of this paper is to reflect on the role of electric lighting design in urban regeneration processes. The landscape of the modern city is the result of an accumulation of the various physical, economic, social and cultural layers over the centuries. Urban lighting may be described as one of the physical layers which due recent developments in the technology of efficient light sources overcomes a major evolution. With...
-
An inverse algorithm for contact heat conduction problems with an interfacial heat source based on a first-order thermocouple model
PublikacjaInverse problems of contact heat conduction with an interfacial heat source are common in various fields of science, engineering and technology. In this study, an algorithm for their solution is developed based on an inverse parametric optimisation method with an impulse response function describing the heat partition and contact heat transfer. A first-order thermocouple model with a time constant parameter is embedded in the impulse...
-
Comparison of heat transfer from single- and double-sided heated horizontal plate under free convection in air with constant heat flux condition
PublikacjaThis paper presents the results of an experimental and numerical study of convective heat transfer from a newly designed double-sided heated horizontal plate in air. To ensure equal heat transfer from both surfaces, the plate was equipped with two independently supplied electric heaters and resistance thermometers on each side. Minimizing the plate's thickness reduced lateral heat loss and improved measurement accuracy. The study...
-
Will NILM Technology Replace Multi-Meter Telemetry Systems for Monitoring Electricity Consumption?
PublikacjaThe estimation of electric power utilization, its baseload, and its heating, light, ventilation, and air-conditioning (HVAC) power component, which represents a very large portion of electricity usage in commercial facilities, are important for energy consumption controls and planning. Non-intrusive load monitoring (NILM) is the analytical method used to monitor the energy and disaggregate total electrical usage into appliance-related...
-
Model-Free Controller Tuning Based on DFT Processing: Application to Induction Motor Drives
PublikacjaIn this paper, we present a new approach based on discrete Fourier transform (DFT) analysis for controller tuning of the closed-loop system with unknown plant. The DFT analysis is used to process the closed-loop measurements collected online to derive the frequency response of an initial closed-loop system that does not provide a good performance. Based on the closed-loop frequency response data, we propose two methods for tuning PID...