Filtry
wszystkich: 1296
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: EDGE-GUIDED MODE
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a microturbine for a cogeneration micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3 kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attentionwas paid...
-
Distance measurement by the low coherent interferometer with NND layer (the source wavelegth 1310 nm)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Images of topography and mechanical properties (phase imaging) of cast iron samples from water installations
Dane BadawczeMeasurements in contact and semi-contact mode. NTEGRA Prima (NT-MDT) device. CSG 10.
-
Atomic force microscopy images of copper electrical contacts wear under the influence of friction
Dane BadawczeMeasurement of wear of copper electrical contacts under the influence of friction. Imaging in contact mode in the variant of scanning spreading resistance microscopy. Additionally, there are spectroscopic current-voltage curves showing local changes in electrical conductivity. NTEGRA Prima (NT-MDT) device. Probe NSG 01Pt.
-
Influence of the annealing condictions on the chemical structure of LaBaGdCo ceramics
Dane BadawczeCeramic samples based on Barium, Lanthanum, Gadolinium and Cobaltium were produced by solid state reaction. After sintring in a furnance, samples were annealed at 300 Celsius degree in wet and dry atmosphere. Annealing takes 72h or 2h. Results of annealing were observed by X-Ray photoemission spectroscopy (XPS), OmicronNanotechnology. XPS analysis...
-
Implementation of DEIS for reliable fault monitoring and detection in PEMFC single cells and stacks
PublikacjaDynamic Electrochemical Impedance Spectroscopy (DEIS) was presented as novel method for diagnostic and monitoring of PEMFC stack and single cells operation. Impedance characteristics were obtained simultaneously with current - voltage characteristics for stack and each individual cell. Impedance measurements were performed in galvanodynamic mode. It allowed to compare performance of each cell and identification of faulty cell operation...
-
Electromagnetic plane wave scattering from a cylindrical object with an arbitrary cross section using a hybrid technique
PublikacjaA hybrid technique combining finite-element and mode-matching methods for the analysis of scattering problems in open and closed areas is presented. The main idea of the analysis is based on the utilization of the finite-element method to calculate the post impedance matrix and combine it with external excitation. The discrete analysis, which is the most time- and memory-consuming, is limited here only to the close proximity of...
-
Continuum models for pantographic blocks with second gradient energies which are incomplete
PublikacjaWe postulate a deformation energy for describing the mechanical behavior of so called pantographic blocks, that is bodies constituted by stacking of layers of pantographic sheets. We remark that the pantographic effect is limited in the plane of pantographic sheets and therefore only the second derivatives of transverse displacements along the pantographic fibers appear in the chosen deformation energy. We use this novel energy...
-
Asymmetrical Modes in Polyphase Motors and Drives
PublikacjaThe effect of power supply and/or motor asymmetry on the phase-load distribution and the ripple of electromagnetic torque in a polyphase drive is studied by the method of symmetrical components. It is shown that the presence of asymmetry causes the mapping of all harmonics in the supply voltage into all planes of symmetrical components and eliminates the possibility of independent control of harmonics. The dynamic model of a five-phase...
-
Resonant DC link inverters for AC motor drive systems – critical evaluation
PublikacjaIn this survey paper, resonant and quasiresonant DC link inverters are reexamined for AC motor drive applications. Critical evaluation of representative topologies is based on simulation and waveform analysis to characterize current/voltage stress of components, control timing constraints and feasibility. A special concern over inverter common-mode voltage and voltage gradient du/dt limitation capacity is discussed for motor bearing...
-
Crystal growth and properties of a binary intermetallic ZrBi2 compound
PublikacjaSingle crystals of ZrBi2 were grown by a self-flux method. The material adopts TiAs2 structure type with lattice parameters: a = 10.233(4) Å, b = 15.581(2) Å, c = 3.994(5) Å. Crystals of ZrBi2 were studied by means of magnetic susceptiblity, specific heat and resistivity measurements. The compound reveals a metallic-like behavior (RRR = 30). The Sommerfeld coefficient equals γ = 1.59(16) mJ mol-1 K-2 and Debye temperature ΘD =...
-
Transient States during Short-circuit in a Line Powered by UPS and its Impact on Earth Fault Loop Impedance Measurement and Power Quality
PublikacjaThe short-circuit in a line powered by Uninterruptible Power Supply (UPS) during different UPS operation modes is presented in the article. The transient state condition related to the short-circuit in a line fed from double conversion On-line UPS is discussed in detail. The results of the measurements of earth fault loop impedance (FLI) in circuits powered by UPS with the instruments of various manufacturers are presented. The...
-
Struktury sieci transportu zbiorowego w miastach
PublikacjaPotrzeby przewozowe mieszkańców miast powinny być zaspokajane poprzez dopasowaną i sprawnie funkcjonującą sieć transportu zbiorowego. Planując sieć i decydując się jednocześnie na jej sposób funkcjonowania istotnym jest uwzględnienie podstawowych postulatów przewozowych mieszkańców. Ostateczny kształt tej sieci wynika jednak z dodatkowych czynników zarówno infrastrukturalnych, ekonomicznych, jak i wielu innych. Celem niniejszego...
-
QUEUE I
WydarzeniaFaculty of Applied Physics and Mathematics of Gdańsk Tech invites international students to the next summer school - Quantum and Molecules I (QUEUE I), organized within the ScienceApp project.
-
A spice equivalent circuit for modeling the performance of dual frequency echo-sounder
PublikacjaThe paper presents novel network equivalent circuit of piezoceramic circular disc transducers that takes into account thickness and radial mode of vibrations. The starting point of the analysis is 4-port description of circular disc element representing the solution of wave equation set in radial and thickness directions. The approximate solution for harmonic case is represented in the form of 4x4 matrix, which is synthesised and...
-
Dictionnaires bilingues, patrimoine culturel et enseignement du français
PublikacjaL’enseignement des faits de culture, en particulier des phrasèmes, est considéré comme une urgence pour la formation du citoyen actif, d’où l’importance du recours aux dictionnaires bilingues. Or, si le recours à ces supports est fréquent chez les apprenants, il n’est pas recommandé par les enseignants. Notre objectif est de montrer que le recours aux dictionnaires bilingues doit être dosé et que le mode de consultation de ces...
-
Video analytics-based algorithm for monitoring egress from buildings
PublikacjaA concept and a practical implementation of the algorithm for detecting of potentially dangerous situations related to crowding in passages is presented. An example of such a situation is a crush which may be caused by an obstructed pedestrian pathway. The surveillance video camera signal analysis performed in the online mode is employed in order to detect hold-ups near bottlenecks like doorways or staircases. The details of the...
-
Application of sliding switching functions in backstepping based speed observer of induction machine
PublikacjaThe paper presents an analysis of the speed observer which is based on the backstepping and sliding mode approach. The speed observer structure is based on the extended mathematical model of an induction machine. The observer structure is based on the measured phase stator currents and transformed to ( αβ ) coordinate system. The stator voltage vector components are treated as known values. Additionally, such an observer structure...
-
Two tests for adhesive bonding long term characterization: principles and applications
PublikacjaThis article describes recent refinement of the traditional wedge test technique used to characterize durability of the adhesive joints. We propose two types of measuring protocols to monitor precisely and continuously the propagation of an "effective" crack during long term mode I fracture mechanic test. First method is directly derived from the traditional wedge test technique and consist in monitoring the surface strain of adherent...
-
Efficiency of acoustic heating in the Maxwell fluid
PublikacjaThe nonlinear effects of sound in a fluid describing by the Maxwell model of the viscous stress tensor is the subject of investigation. Among other, viscoelastic biological media belong to this non-newtonian type of fluids. Generation of heating of the medium caused by nonlinear transfer of acoustic energy, is discussed in details. The governing equation of acoustic heating is derived by means of the special linear combination...
-
Risk Analysis by a Probabilistic Model of the Measurement Process
PublikacjaThe aim of the article is presentation of the testing methodology and results of examination the probabilistic model of the measurement process. The case study concerns the determination of the risk of an incorrect decision in the assessment of the compliance of products by measurement. Measurand is characterized by the generalized Rayleigh distribution. The model of the meas-urement process was tested in parallel mode by six risk...
-
Fracture prediction in flat PMMA notched specimens under tension - effectiveness of the equivalent material concept and fictitious material concept
PublikacjaThe fracture of notched elements under mode I loading (tension) remains an inexhaustible research topic, especially when it comes to the fracture of thermoplastic materials such as polymethylmethacrylate (PMMA), which experience considerable plastic strains under tension. The paper points out that traditional brittle fracture criteria such as mean stress (MS) or maximum tangential stress (MTS) criteria used to predict this phenomenon do...
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublikacjaThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
Speed Observer Structure of Induction Machine Based on Sliding Super-Twisting and Backstepping Techniques
PublikacjaThis paper presents an analysis of the two speed observer structures which are based on the backstepping and sliding super twisting approach. The observer stabilizing functions result from the Lyapunov theorem. To obtain the observer tuning gains the observer structure is linearized near the equilibrium point. The rotor angular speed is obtained from non-adaptive dependence. In the sensorless control system structure the classical...
-
GPU-Accelerated LOBPCG Method with Inexact Null-Space Filtering for Solving Generalized Eigenvalue Problems in Computational Electromagnetics Analysis with Higher-Order FEM
PublikacjaThis paper presents a GPU-accelerated implementation of the Locally Optimal Block Preconditioned Conjugate Gradient (LOBPCG) method with an inexact nullspace filtering approach to find eigenvalues in electromagnetics analysis with higherorder FEM. The performance of the proposed approach is verified using the Kepler (Tesla K40c) graphics accelerator, and is compared to the performance of the implementation based on functions from...
-
Efficiency of acoustic heating in the Maxwell fluid
PublikacjaThe nonlinear effects of sound in a fluid describing by the Maxwell model of the viscous stress tensor is the subject of investigation. Among other, viscoelastic biological media belong to this non-newtonian type of fluids. Generation of heating of the medium caused by nonlinear transfer of acoustic energy, is discussed in details. The governing equation of acoustic heating is derived by means of the special linear combination...
-
Nonlinear Influence of Sound on the Vibrational Energy of Molecules in a Relaxing Gas
PublikacjaDynamics of a weakly nonlinear and weakly dispersive flow of a gas where molecular vibrational relaxation takes place is studied. Variations in the vibrational energy in the field of intense sound is considered. These variations are caused by a nonlinear transfer of the acoustic energy into energy of vibrational degrees of freedom in a relaxing gas. The final dynamic equation which describes this is instantaneous, it includes a...
-
Wybrane aspekty zachowań internautów oraz rozwój komunikacji marketingowej w Internecie - Polska na tle innych krajów europejskich
PublikacjaCelem artykułu jest zaprezentowanie różnic w zachowaniach klientów on-line oraz rozwoju komunikacji marketingowej w Internecie. W opracowaniu powołano się na wyniki badań internautów przeprowadzonych w Polsce i w innych krajach Europy. Przybliżono w nim najbardziej charakterystyczne cechy i zachowania użytkowników Internetu. Oprócz tego, w artykule ukazano istotę podejścia inbound marketing w kreowaniu wartościowych treści z punktu...
-
Wybrane wyniki badań potrzeb transportowych mieszkańców województwa pomorskiego
PublikacjaNa potrzeby opracowania Planu Zrównoważonego Rozwoju Publicznego Transportu Zbiorowego Województwa Pomorskiego w czwartym kwartale 2013 roku konsorcjum Fundacji Rozwoju Inżynierii Lądowej oraz z Politechniki Gdańskiej wykonało badania potrzeb transportowych mieszkańców województwa pomorskiego oraz wielkości popytu na usługi przewozowe. Uzyskane wyniki były podstawą do budowy transportowego modelu symulacyjnego podróży realizowanych...
-
Constructing a map of an anonymous graph: applications of universal sequences
PublikacjaWe study the problem of mapping an unknown environmentrepresented as an unlabelled undirected graph. A robot (or automaton)starting at a single vertex of the graph G has to traverse the graph and return to its starting point building a map of the graph in the process. We are interested in the cost of achieving this task (whenever possible) in terms of the number of edge traversal made by the robot. Another optimization criteria...
-
Chitosan-based electrospun nanofibers for encapsulating food bioactive ingredients: A review
PublikacjaToday, society has been more aware of healthy food products and related items containing bioactive compounds, which potentially contribute to human health. Unfortunately, the long-term stability and bioactivity of biologically active compounds against environmental factors compromise their target and effective action. In this way, lab-designed vehicles, such as nanoparticles and nanofibers, provide enough properties for their preservation...
-
Water-Lubricated Journal Bearings Marine Applications, Design, and Operational Problems and Solutions
PublikacjaWater-Lubricated Journal Bearings: Marine Applications, Design, and Operational Problems and Solutions provides cutting-edge design solutions, common problems and methods for avoiding them, and material selection considerations for the use of water-lubricated journal bearings in marine environments. These bearings have many advantages, including the absence of the potential for oil contamination. They are also sensitive, and their...
-
Bio-inspired Decisional DNA in Machinas and other Man-made Systems: The Way Forward
PublikacjaArtificial bio-inspired intelligent techniques and systems supporting smart, knowledge-based solutions of real world problems which are currently researched very extensively by research teams around the world, have enormous potential to enhance automation of decision making and problem solving for a number of diverse areas including design, manufacturing, Information Technology (IT), social communities of practice, and economics...
-
Fracture Toughness and Shear Yield Strength Determination for Two Selected Species of Central European Provenance
PublikacjaWhen offcut of wood is formed by shearing, Atkins’s analyses of sawing processes can be applied. Using this modern approach, it is possible to determine the fracture toughness and shear yield strength of wood. This model is only applicable for the axial-perpendicular cutting direction because both of these parameters are suitable for the given direction of cutting edge movement and cannot be considered material constants. Alternatively,...
-
Hat problem on a graph
PublikacjaThe topic of our paper is the hat problem. In that problem, each of n people is randomly fitted with a blue or red hat. Then everybody can try to guess simultaneously his own hat color looking at the hat colors of the other people. The team wins if at least one person guesses his hat color correctly and no one guesses his hat color wrong, otherwise the team loses. The aim is to maximize the probability of win. In this version every...
-
A Proposed Machine Learning Model for Forecasting Impact of Traffic-Induced Vibrations on Buildings
PublikacjaTraffic-induced vibrations may cause various damages to buildings located near the road, including cracking of plaster, cracks in load-bearing elements or even collapse of the whole structure. Measurements of vibrations of real buildings are costly and laborious. Therefore the aim of the research is to propose the original numerical algorithm which allows us to predict, with high probability, the nega-tive dynamic impact of traffic-induced...
-
The convex domination subdivision number of a graph
PublikacjaLet G = (V;E) be a simple graph. A set D\subset V is a dominating set of G if every vertex in V - D has at least one neighbor in D. The distance d_G(u, v) between two vertices u and v is the length of a shortest (u, v)-path in G. An (u, v)-path of length d_G(u; v) is called an (u, v)-geodesic. A set X\subset V is convex in G if vertices from all (a, b)-geodesics belong to X for any two vertices a, b \in X. A set X is a convex dominating...
-
Multi-stage magnetic-fluid seals for operating in water - life test procedure, test stand and research results
PublikacjaThe edge criteria for magnetic-fluid seals durability research are critical for the seal'stechnological usefulness. The magnetic fluid seal technology in water is much moredifficult technological problem in comparison to gas or vacuum environment. There isalways problem with immediate contact between magnetic fluid and the environmentaluninspected liquids. In the paper are presented ways of experiments definitions carried outwith...
-
A Comparative Study of Fuzzy SMC with Adaptive Fuzzy PID for Sensorless Speed Control of Six-Phase Induction Motor
PublikacjaMulti-phase motors have recently replaced three-phase induction motors in a variety of applications due to the numerous benefits they provide, and the absence of speed sensors promotes induction motors with variable speed drives. Sensorless speed control minimizes unnecessary speed encoder cost, reduces maintenance, and improves the motor drive’s reliability. The performance comparison of the fuzzy sliding mode controller (FSMC)...
-
Molecular basis and quantitative assessment of TRF1 and TRF2 protein interactions with TIN2 and Apollo peptides
PublikacjaShelterin is a six-protein complex (TRF1, TRF2, POT1, RAP1, TIN2, and TPP1) that also functions in smaller subsets in regulation and protection of human telomeres. Two closely related proteins, TRF1 and TRF2, make high-affinity contact directly with double-stranded telomeric DNA and serve as a molecular platform. Protein TIN2 binds to TRF1 and TRF2 dimer-forming domains, whereas Apollo makes interaction only with TRF2. To elucidate...
-
A Comparative Study of Fuzzy SMC with Adaptive Fuzzy PID for Sensorless Speed Control of Six-Phase Induction Motor
PublikacjaMulti-phase motors have recently replaced three-phase induction motors in a variety of applications due to the numerous benefits they provide, and the absence of speed sensors promotes induction motors with variable speed drives. Sensorless speed control minimizes unnecessary speed encoder cost, reduces maintenance, and improves the motor drive’s reliability. The performance comparison of the fuzzy sliding mode controller (FSMC)...
-
Detection of the acoustic interferences during AFM operation
Dane BadawczeAtomic force microscopy is a particularly complicated surface imaging technique due to the large number of factors that affect the quality of the resulting images. They are obviously difficult and sometimes even impossible to control at the same time. One of such factors may even be the seismological location of the building or the influence of mechanical...
-
Valence state of Manganium in a MnCoO ceramics
Dane BadawczeManganium -cobalt based ceramics materials were produced by solid state reaction and sintred in a furnance in air atmosphere for 20h. Annealing temperature was 600 Celsius degree. For investigations a series of samples, with a various composition was chosen: MnCoO, Mn, Co2O and Mn2CoO. In order to determine valence states of the Mn, X-Ray photoemission...
-
Lanthanum investigations in ceramics annealed in a dry and wet atmosphere
Dane BadawczeCeramics based on Barium, Lanthanum, Gadolinium and Cobaltium were produced by standard solid state reaction from oxides and carbonate powders. After sintring, samples were annealed for 2 hours or 72 hours at 300 Celsius degree in a both: wet and dry atmosphere. Results of annealing on a chemical composition and valence state of lanthanum were observed...
-
Machine-Learning-Based Global Optimization of Microwave Passives with Variable-Fidelity EM Models and Response Features
PublikacjaMaximizing microwave passive component performance demands precise parameter tuning, particularly as modern circuits grow increasingly intricate. Yet, achieving this often requires a comprehensive approach due to their complex geometries and miniaturized structures. However, the computational burden of optimizing these components via full-wave electromagnetic (EM) simulations is substantial. EM analysis remains crucial for circuit...
-
Permanent traffic count stations - expressway S6 Poland 2016
Dane BadawczeThe data includes traffic data from permanent traffic count stations located on the expressway S6 in the Tri-City Agglomeration area in Poland. The data covers the 12 months of 2016.
-
Threshold photoelectron studies of isoxazole over the energy range 9.9-30 eV
PublikacjaThe threshold photoelectron spectrum of the isoxazole molecule, C3H3NO has been measured over the photon energy range 9.9-30 eV with the use of synchrotron radiation. In the 9.9-10.8 eV range, corresponding to photoionization from the highest occupied molecular orbital 3a"(π3), seven well resolved vibrational series have been observed and their modes are tentatively assigned. A strong adiabatic ionization, with an energy of 11.132...
-
Robustly feasible integral LQ-MPC controller for output tracking in constrained linear systems
PublikacjaW pracy rozważany jest regulator predykcyjny typu dual-mode MPC z liniowo kwadratowym wskaźnikiem jakości w aplikacji do krzepkiego śledzenia wyjść liniowego obiektu dyskretnego w obecności addytywnych zakłóceń. W celu zapewnienia dopuszczalności sterowań regulatora wykorzystano teorię zbiorów niezmienniczych. W celu polepszenia śledzenia wyjść i odrzucenia zakłóceń w regulatorze wykorzystano działanie całkujące (integral control)....
-
Instrumented End Notched Flexure - Crack propagation and process zonemonitoring. Part I: Modelling and analysis
PublikacjaAnalysis of the three-point bending, End Notched Flexure (ENF), test is presented for exploitation with a new experimental methodology using the backface strain monitoring technique. The model consists oftwo Timoshenko beams joined with a two parameter elastic foundation, to evaluate stress and strain fields in both adherends and the adhesive layer, together with the specimen compliance and energyrelease rate. This model is compared...
-
Microwave-assisted preparation of potato starch silicated with silicic acid
PublikacjaApplication of microwave irradiation for the silication of granular potato starch with silicic acid, and the properties of silicated starch were investigated. Potato starch was esterified on 20 min microwave irradiation of starch with silicic acid, applying the power of 450 or 800Wand, for comparison, on 120 min convectional heating of the reagent blend at 100 ◦C. The degree of esterification and the reaction efficiency did not...