Wyszukiwarka
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: DELAY-DIFFERENTIAL EQUATIONS
-
Acoustic Processor of the MCM Sonar
PublikacjaThis paper presents the concept of an acoustic processor of the mine countermeasure sonar. Developed at the Department of Marine Electronics Systems, Gdansk University of Technology, the acoustic processor is an element of the MG-89, a modernised underwater acoustic station. The focus of the article is on the modules of the processor. They are responsible for sampling analogue signals and implementing the algorithms controlling...
-
Hybrid Model of Axially Moving Continua
PublikacjaThe paper introduces the method of the model reduction of systems that experience a Coriolis acceleration component. It causes that system equations are non-self-adjoined. To avoid such problem modal, reduced model is built up for the system without Coriolis acceleration terms which are next included by application of any lumping technique. Hence, the final reduced model is a hybrid one, obtained by both lumping and modal methods...
-
Direct shear stress vs strain relation for fiber reinforced composites
PublikacjaThe majority of fiber reinforced composites exhibit strong non-linear behavior in in-plane shear state. The effect is attributed to the micro-cracks appearing in the matrix and can be modeled on the micro and macro level. In this work the author proposes constitutive laws describing the non-linear in-plane shear response, which can be alternative for the relations commonly considered in the literature. The proposed equations are...
-
GPU-accelerated finite element method
PublikacjaIn this paper the results of the acceleration of computations involved in analysing electromagnetic problems by means of the finite element method (FEM), obtained with graphics processors (GPU), are presented. A 4.7-fold acceleration was achieved thanks to the massive parallelization of the most time-consuming steps of FEM, namely finite-element matrix-generation and the solution of a sparse system of linear equations with the...
-
Regulator przepływu
PublikacjaW artykule opisano konstrukcję i wyniki badań prototypu regulatora przepływu charakteryzującego się brakiem sprężyny. W regulatorze zawór różnicowy zastąpiono zaworem stosunku ciśnień. Charakterystyki przepływowe regulatora mają przebieg niezależny od obciążenia. Nastawa regulatora odbywa się poprzez obrót hydrostatycznie odciążonej tulei dławiącej, wewnątrz której umieszczony jest suwak główny i suwak pomocniczy zaworu stosunku...
-
Determination of Antioxidant Activity of Vitamin C by Voltammetric Methods
PublikacjaVoltammetric methods—cyclic (CV) and differential pulse voltammetry (DPV) are considered the most appropriate way to evaluate antioxidant activity of redox active compounds. They provide information about both mechanism and kinetics of electrochemical oxidation of antioxidants as well as their physical and chemical properties such as the redox potential or the number of electrons transferred. These methods are helpful for understanding...
-
System of wireless magnetic sensors for detection and identification of ferromagnetic vehicles
PublikacjaThe paper presents the results of deformation of the Earth's magnetic field by land vehicles. Basing on the analysis of the shape of the magnetic field deformation, it is possible to detect and identify a vehicle. In order to eliminate the interference of the Earth's magnetic field by the environment, the measurements were performed in a differential configuration. Under a development project a wireless system of magnetic sensors...
-
Local buckling and initial post-buckling behaviour of channel member flange - analytical approach
PublikacjaThe local buckling and initial post-buckling behaviour of the cold-formed channel member flange is investigated. The governing nonlinear differential equation for axially compressed columns and beams undergoing pure bending is derived using the stationary total potential energy principle. The critical stress and initial post-buckling equilibrium path is determined by means of a perturbation approach. The results obtained allow...
-
Formation of intermetallic compounds in the solid-liquid composites of the Ga-Ni system
PublikacjaThe processes of formation of intermetallic compounds in the composite system of liquid gallium-nickel powder by the methods of x-ray diffraction, scanning electron microscopy and differential thermal analysis have been studied. A change in the phase composition was discovered and the influence of thermal treatment of the composites under investigation on the phase formation processes was analyzed. The mechanism of gallium enriched...
-
Improved finite element method for flow, heat and solute transport of Prandtl liquid via heated plate
PublikacjaIn the current study, a vertical, 3D-heated plate is used to replicate the generation of heat energy and concentration into Prandtl liquid. We discuss how Dufour and Soret theories relate to the equations for concentration and energy. In order to see how efectively particles, interact with heat and a solvent, hybrid nanoparticles are used. It does away with the phenomena of viscous dissipation and changing magnetic felds. The motivation...
-
Joint experimental and theoretical study on electron scattering from titanium tetrachloride (TiCl4) molecule
PublikacjaAbsolute grand-total cross section for electron scattering from titanium tetrachloride, TiCl4, molecule was measured at electron-impact energies ranging from 0.3 to 300 eV, in the linear electron-transmission experiment. The elastic integral, differential, momentum transfer, and total ionization cross sections for TiCl4 molecule were also calculated for low and intermediate collisional energies at the level of various theories. The...
-
Biowaste chicken eggshell powder as a potential cure modifier for epoxy/anhydride systems: competitiveness with terpolymer-modified calcium carbonate at low loading levels
PublikacjaBiowaste chicken eggshell (ES) powder was applied as a potential cure modifier in epoxy/anhydride systems. Cure behaviour and kinetics of composites filled with very low content (0.1 wt% based on epoxy resin) of ES, calcium carbonate (CaCO3), and terpolymer-modified fillers, mES and mCaCO3, were discussed comparatively. Surface analysis was performed by X-ray photoelectron spectroscopy. Cure kinetics was investigated by differential...
-
Hybrid model of moving or rotating continua
PublikacjaThe paper introduces the method of the model reduction of systems that experience a Coriolis acceleration or gyroscopic effect component. In such causes that corresponding system equations are non-self-adjoined. Modal reduced model is built up for the system without Coriolis or gyroscopic effect terms. These phenomena are next included by application of any lumping technique. Hence, the final reduced model is a hybrid one, obtained...
-
Some fundamental aspects of self-levitating sliding contact bearings and their practical implementations
PublikacjaIn this study, fundamental aspects and mechanisms of acoustic levitation together with governing equations are presented first. Then, the acoustic levitation phenomenon is considered as a new way to design air suspension systems capable of self-levitation. A particular emphasis is laid on journal bearings and their specific geometrical configuration. A practical feasibility of using acoustic levitation to separate contacting surfaces...
-
Elastoplastic material law in 6-parameter nonlinear shell theory
PublikacjaWe develop the elastoplastic constitutive relations for nonlinear exact 6-parameter shell theory. A J2-type theory with strain hardening is formulated that takes into account asymmetric membrane strain measures. The incremental equations are solved using implicit Euler scheme with closest point projection algorithm. The presented test example shows the correctness of the proposed approach. Influence of micropolar material parameters...
-
NON-STATIONARY THERMAL SELF-ACTION OF ACOUSTIC BEAMS CONTAINING SHOCK FRONTS IN THERMOCONDUCTING FLUID
PublikacjaNon-stationary thermal self-action of a periodic or impulse acoustic beam containing shock fronts in a thermoconducting Newtonian fluid is studied. Self-focusing of a saw-tooth periodic and impulse sound is considered, as well as that of a solitary shock wave which propagates with the linear sound speed. The governing equations of the beam radius are derived. Numerical simulations reveal that the thermal conductivity weakens the...
-
Fluid Mechanics and Hydraulics EE Msc sem. I r.a. 22/23
Kursy OnlineBasic definitions. Physical properties of liquids. Forces acting on fluids. Hydrostatics - basic equations. Pressure on a flat and curved wall. Buoyancy. Archimedes' law. Balance of submerged bodies. The balance of floating bodies. Hydrodynamics. Hydrodynamic quantities. Continuity equation for the liquid stream. Bernoulli equation. Basic laws of hydrodynamics. Equation of mass behavior, preservation of the amount of motion, Bernoulli's...
-
Fluid Mechanics and Hydraulics EE Msc sem. I r.a. 23/24
Kursy OnlineBasic definitions. Physical properties of liquids. Forces acting on fluids. Hydrostatics - basic equations. Pressure on a flat and curved wall. Buoyancy. Archimedes' law. Balance of submerged bodies. The balance of floating bodies. Hydrodynamics. Hydrodynamic quantities. Continuity equation for the liquid stream. Bernoulli equation. Basic laws of hydrodynamics. Equation of mass behavior, preservation of the amount of motion, Bernoulli's...
-
Study of Slip Effects in Reverse Roll Coating Process Using Non-Isothermal Couple Stress Fluid
PublikacjaThe non-isothermal couple stress fluid inside a reverse roll coating geometry is considered. The slip condition is considered at the surfaces of the rolls. To develop the flow equations, the mathematical modelling is performed using conservation of momentum, mass, and energy. The LAT (lubrication approximation theory) is employed to simplify the equations. The closed form solution for velocity, temperature, and pressure gradient...
-
THE PROBLEM OF AIRFLOW AROUND BUILDINGS CLUSTERS IN DIFFERENT CONFIGURATIONS
PublikacjaIn the paper, the authors discuss the construction of a model of an exemplary urban layout. Numerical simulation has been performed by means of a commercial software Fluent using two different turbulence models: the popular k-ε realizable one, and the Reynolds Stress Model (RSM), which is still being developed. The former is a 2-equations model, while the latter – is a RSM model – that consists of 7 equations. The studies have...
-
Postquarter-Point Case of Ship’s Side-Berthing and Its Influence on Marine Fender Pitch
PublikacjaThis paper presents a critical analysis of some selected codes and practical recommendations used as basic rules in the design procedures of modern marine fender systems. The first part of the discussion pertains to the existing equations used in calculating the eccentricity coefficient in the ship’s kinetic energy equation and the maximum allowable fender pitch (spacing) in a set of fenders installed along a quay wall. A new approach...
-
Metody zwiększania dostępności i efektywności informatycznej infrastruktury w inteligentnym mieście
PublikacjaW pracy omówiono metody zwiększania dostępności i efektywności informatycznej infrastruktury w inteligentnym mieście. Sformułowano dwa kryteria do oceny rozmieszczenia kluczowych zasobów w systemie smart city. Zobrazowano proces wyznaczania rozwiązań kompromisowych spośród rozwiązań Pareto-optymalnych. Omówiono metaheurystyki inteligencji zbiorowej, w tym roju cząstek, kolonii mrówek, roju pszczół oraz ewolucji różnicowej, za pomocą...
-
Modal Reduction and Analysis of Gyroscopic Systems
PublikacjaThe paper introduces the method of the modal reduction of systems that experience the Coriolis acceleration or gyroscopic effect component. In such cases corresponding system equations are non-self-adjoined. To solve the problem modal reduced model is built up for the system without Coriolis acceleration or gyroscopic effect terms. These phenomena are included by application of any lumping technique. Hence, the final reduced model...
-
An algorithm for enhancing macromodeling in finite element analysis of waveguide components
PublikacjaAn algorithm for enhancing the finite element method with local model order reduction is presented. The proposed technique can be used in fast frequency domain simulation of waveguide components and resonators. The local reduction process applied to cylindrical subregions is preceded by compression of the number of variables on its boundary. As a result,the finite element large system is converted into a very compact set of linear...
-
A new prototype of piezoelectric bending resonant transducer for analysis of soft tissues properties
PublikacjaThis paper is devoted to a new piezoelectric bending resonant transducer prototype dedicated to the characterization of the mechanical properties of soft tissue. A general description of the actuator’s structure is presented including the basic principles of the measurement. The chosen geometry of the prototype is discussed and compared with the existing version. Constitutive equations are presented for the active and passive layer...
-
Design and simulation of a new prototype of piezoelectric cantilever sensor/actuator for analysis of the soft tissues properties
PublikacjaThis paper is devoted to a new prototype of piezoelectric cantilever transducer dedicated for the characterization of the mechanical properties of soft tissues. General description of the actuator’s structure is presented including the basic principles of the measurement. The chosen geometry of the prototype is discussed and compared with the existing one. Constitutive equations are presented for the active and passive layer of...
-
Enhanced trap-assisted recombination in organic semiconductors
PublikacjaAn analytical model to describe the interaction of excitons and charge transfer states with deep traps is formulated for the case of molecular materials. Here, we have considered the influence of a trap-assisted recombination on this phenomenon. The final expression for the effective recombination rate has been derived from the Shockley–Read–Hall theory and kinetic equations which characterize different photophysical processes....
-
Verification of algorithms determining wave loads on support structure of wind turbine
PublikacjaThe offshore wind turbines require determination of wave loads on their support structure. This structure is fixed and, therefore, this problem is reduced to solving only the diffraction problem, which is determined by Laplace equation and conditions on the following boundaries: on the support structure, on the sea free surface and on its bottom, and at infinity on free surface. The linear problem was applied to determine the wave...
-
Design of Microstrip UWB Balun Using Quasi-TEM Approach Aided by the Artificial Neural Network
PublikacjaThe design procedure for UWB balun realized in the microstrip technology is proposed in the paper. The procedure applies Artificial Neural Network which corrects the dimensions of the approximate design found by appropriate scaling of the dimensions of the prototype. The scale coefficients for longitudinal and transverse dimensions of microstrip lines are determined from electromagnetic modeling based on transmission line equations....
-
State Observer for Doubly-fed Induction Generator
PublikacjaIn the paper a new state observer for doubly-fed generator has been proposed. In the new approach an extended mathematical model of the doubly fed generator is used to form equations of the introduced z type observer. Stability of the observer has been verified through poles placement analyses. The active and reactive powers of the generator are controlled by a nonlinear multiscalar control method. Simulation and experimental results...
-
Simulation of influence of the air gap asymmetryon voltage waveforms of a synchronous machine
PublikacjaResults of simulation of a synchronous generator with the air gap asymmetry characterised by eccentricity are presented in the paper. The Lagrange's energy method has been used in derivation of the model equations. Analysis of influence of the air gap asymmetry on characteristics of self and mutual inductances of windings, as well as analysis of induced voltage waveforms as a function of the air gap asymmetry have been performed....
-
Simulation model for evaluation of packet sequence changed order of stream in DiffServ network
PublikacjaCurrent packet networks use a large variety of mechanisms which should support QoS (Quality of Service). One of those mechanisms is routing (calculating connection paths for incoming service requests). The most effective mechanism in QoS context is dynamic routing, which is based on the current network state described by the offered traffic matrix and link states. After switching between calculated available paths, connection...
-
Investigation of the 16-year and 18-year ZTD Time Series Derived from GPS Data Processing
PublikacjaThe GPS system can play an important role in activities related to the monitoring of climate. Long time series, coherent strategy, and very high quality of tropospheric parameter Zenith Tropospheric Delay (ZTD) estimated on the basis of GPS data analysis allows to investigate its usefulness for climate research as a direct GPS product. This paper presents results of analysis of 16-year time series derived from EUREF Permanent Network...
-
A Self-Equalized Waveguide Filter With Frequency-Dependent (Resonant) Couplings
PublikacjaThis letter presents a design of a fifth-order linear phase filter with frequency-dependent couplings. The filter is composed of a triplet that is directly coupled to two resonators at the input and output. To provide group delay flattening a cross-coupling in the trisection has a strongly dispersive character with a negative slope parameter. To achieve this, an E-plane stub with a septum was used. To further improve the filter...
-
Time versus space trade-offs for randezvous in trees
PublikacjaTwo identical (anonymous) mobile agents start from arbitrary nodes of an unknown tree and have to meet at some node. Agents move in synchronous rounds: in each round an agent can either stay at the current node or move to one of its neighbors. We consider deterministic algorithms for this rendezvous task. The main result of this paper is a tight trade-off between the optimal time of completing rendezvous and the size of memory...
-
High-Speed Binary-to-Residue Converter Design Using 2-Bit Segmentation of the Input Word
PublikacjaIn this paper a new approach to the design of the high-speed binary-to-residue converter is proposed that allows the attaining of high pipelining rates by eliminating memories used in modulo m generators. The converter algorithm uses segmentation of the input binary word into 2-bit segments. The use and effects of the input word segmentation for the synthesis of converters for five-bit moduli are presented. For the number represented...
-
A continual model of a damaged medium used for analyzing fatigue life of polycrystalline structural alloys under thermal–mechanical loading
PublikacjaThe main physical laws of thermal–plastic deformation and fatigue damage accumulation processes in polycrystalline structural alloys under various regimes of cyclic thermal–mechanical loading are considered. Within the framework of mechanics of damaged media, a mathematical model is developed that describes thermal–plastic deformation and fatigue damage accumulation processes under low-cycle loading. The model consists of three...
-
A chemo-mechano-thermodynamical contact theory for adhesion, friction, and (de)bonding reactions
PublikacjaThis work presents a self-contained continuum formulation for coupled chemical, mechanical, and thermal contact interactions. The formulation is very general and, hence, admits arbitrary geometry, deformation, and material behavior. All model equations are derived rigorously from the balance laws of mass, momentum, energy, and entropy in the framework of irreversible thermodynamics, thus exposing all the coupling present in the...
-
Analysis of Floodplain Inundation Using 2D Nonlinear Diffusive Wave Equation Solved with Splitting Technique
PublikacjaIn the paper a solution of two-dimensional (2D) nonlinear diffusive wave equation in a partially dry and wet domain is considered. The splitting technique which allows to reduce 2D problem into the sequence of one-dimensional (1D) problems is applied. The obtained 1D equations with regard to x and y are spatially discretized using the modified finite element method with the linear shape functions. The applied modification referring...
-
Nonlocal elasticity analysis of moderately thick porous functionally graded plates in a hygro-thermal environment
PublikacjaThis work performs a novel quasi three-dimensional (3D) bending analysis for a moderately thick functionally graded material (FGM) made of nanoceramics and metal powders, in presence of porosities due to some incorrect manufacturing processes. Such porosities can appear within the plate in two forms, namely, even and uneven distributions. The modeled system assumes a polymer matrix where both shear and transverse factors coexist....
-
On the non-linear dynamics of torus-shaped and cylindrical shell structures
PublikacjaIn this study, the non-linear dynamic analysis of torus-shaped and cylindrical shell-like structures has been studied. The applied material is assumed as the functionally graded material (FGM). The structures are considered to be used for important machines such as wind turbines. The effects of some environmental factors on the analysis like temperature and humidity have been considered. The strain field has been calculated in...
-
Assessment of codes recommendations for the evaluation of the seismic gap of buildings founded on different soil types
PublikacjaSeveral equations have been proposed in the literature to evaluate the seismic gap preventing earthquake-induced structural pounding, such as the ones based on the absolute sum of the peak displacements (ABS), the square root of the sum of the squares (SRSS), the double difference method (DDC), Australian code and the approach proposed by Naderpour et al. The aim of this paper is to investigate the accuracy of these equations taking...
-
Multistatyczny, Dopplerowski System określania położenia i prędkości ruchomych celów w wodzie
PublikacjaW omawianym w pracy multistatycznym, dopplerowskim systemie określania położenia i prędkości ruchomych celów w wodzie źródłem sygnału są dwa nadajniki emitujące sinusoidalne, akustyczne fale ciągłe o różnych częstotliwościach, które po odbiciu od ruchomego celu są obierane przez cztery hydrofony. W artykule przedstawiono analize teoretyczna efektu Dopplera, na którym oparte jest działanie systemu oraz metodę rozwiązania głównych...
-
PROCESSING, MECHANICAL AND THERMAL PROPERTIES OF RECYCLED LOW-DENSITY POLYETHYLENE STREAMS
PublikacjaThe recycling of plastics is currently one of the most significant industrial challenges. Due to the enormous amounts of plastic wastes generated by various industry branches, it is essential to look for the potential methods of their utilization. Nevertheless, for the efficient application of recycled materials it is crucial to analyze their performance. Therefore, in presented paper we investigated the processing (melt flow index),...
-
Development of the sound field 3D intensity probe based on miniature microphones
PublikacjaThe engineered measuring probe uses three pairs of miniature microphones coupled. The signals from the microphones after an initial amplification are fed to differential circuits. Due to the required symmetry of the circuit it was necessary to select electronic components very carefully. Moreover, additional digital signal processing techniques were applied to avoid amplitude and phase mismatch. The view of the engineered probe...
-
On Dynamic Boundary Conditions Within the Linear Steigmann-Ogden Model of Surface Elasticity and Strain Gradient Elasticity
PublikacjaWithin the strain gradient elasticity we discuss the dynamic boundary conditions taking into account surface stresses described by the Steigmann–Ogden model. The variational approach is applied with the use of the least action functional. The functional is represented as a sum of surface and volume integrals. The surface strain and kinetic energy densities are introduced. The Toupin–Mindlin formulation of the strain gradient elasticity...
-
On the correspondence between two- and three-dimensional Eshelby tensors
PublikacjaWe consider both three-dimensional (3D) and two-dimensional (2D) Eshelby tensors known also as energy–momentum tensors or chemical potential tensors, which are introduced within the nonlinear elasticity and the resultant nonlinear shell theory, respectively. We demonstrate that 2D Eshelby tensor is introduced earlier directly using 2D constitutive equations of nonlinear shells and can be derived also using the throughthe-thickness...
-
New Approach to Arc Fitting for Railway Track Realignment
PublikacjaThis article presents a new method of arc fitting for railway track realignment. The theoretical foundations are presented, along with a detailed algorithm of the iterative computational process. This method is based on solving a set of linearized pseudo-observation equations. The formulas of the functional model of the fitting problem were derived, and a special form of objective function is proposed. An iterative method for optimization...
-
On dynamics of origami-inspired rod
PublikacjaWe discuss the dynamics of a relatively simple origami-inspired structure considering discrete and continuum models. The latter was derived as a certain limit of the discrete model. Here we analyze small in-plane deformations and related equations of infinitesimal motions. For both models, dispersion relations were derived and compared. The comparison of the dispersion relations showed that the continuum model can capture the behavior...
-
Non-Wave Variations in Temperature Caused by Sound in a Chemically Reacting Gas
PublikacjaA weakly nonlinear generation of non-acoustic modes in the field of sound in a gas is considered. An exotericchemical reaction of A->B type, which takes place in a gas, may be reversible or not. Two types of sound areconsidered, low-frequency and high-frequency as compared with the characteristic time of a chemical reaction.For both these cases, the governing equations of non-acoustic modes are derived and conclusions of the efficiencyof...