Wyniki wyszukiwania dla: WASTE HEAT
-
Exergy analysis of the Szewalski cycle with a waste heat recovery system
PublikacjaThe conversion of a waste heat energy to electricity is now becoming one of the key points to improve the energy efficiency in a process engineering. However, large losses of a low-temperature thermal energy are also present in power engineering. One of such sources of waste heat in power plants are exhaust gases at the outlet of boilers. Through usage of a waste heat regeneration system it is possible to attain a heat rate of approximately...
-
Use of waste heat to improve the conditions of the piston engines start up
PublikacjaZespoły prądotwórcze z tłokowymi silnikami spalinowymi są obecnie powszechne stosowane jako awaryjne źródła energii elektrycznej albo elektrownie uzupełniające niedobory energii czy stabilizujące częstotliwość. Ich czas rozruchu powinien być krótki - poniżej 5 minut w przypadku dużych mocy. Zużycie silnika, zużycie paliwa i emisji spalin są silnie uzależnione od stanu cieplnego przed rozruchem. Przedstawiono pomiary laboratoryjne...
-
Using adsorption chillers for utilising waste heat from power plants
Publikacja -
Design and experimental investigations of a cylindrical microjet heat exchanger for waste heat recovery systems
PublikacjaCompact heat exchangers have more and more applications in many areas, including the HVAC, food and petrochemical industry. This paper describes the development of heat exchanger technology for waste heat recovery (WHR) from a range of processes. Case-study testing shows that the proposed heat exchanger can successfully enhance heat transfer and recover waste heat in a range of applications making them economically, environmentally and...
-
Optimization of an axial turbine for a small scale ORC waste heat recovery system
Publikacja -
The new concept of capillary forces driven evaporator with application to waste heat recovery
PublikacjaW pracy omówiono koncepcję zastosowania rurki ciepła w nowoczesnej konstrukcji parownika wspomagającego za pomocą sił kapilarnych pompę obiegu termodynamicznego czynnika. Rozwiązanie takie może znaleźć zastosowanie w domowej mikrosiłowni CHP
-
Analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers
PublikacjaThis paper presents an analysis of possibility and purposefulness of application of waste-heat boilers to trailing suction hopper dredgers. Using results of own operational research on dredgers this author determined thermal power demand for six hypothetical trailing suction hopper dredgers of various size, at accounting for a type of power system and kind of fuel combusted by dredger's power plant. By means of basic indices of...
-
Review of Small Gas Turbine Engines and Their Adaptation for Automotive Waste Heat Recovery Systems
Publikacja -
Utilisation of waste heat from the power plant by use of the ORC aided with bleed steam and extra source of heat
PublikacjaUtilization of waste heat recovered from the exhaust gases of the power generation unit by means of ORC (organic Rankine cycles) installation is considered. The waste heat is available in the form of a stream of hot water having temperature of 90 stC in the amount of 200 MWt. To increase evaporation temperaturę of ORC working fluid the heat of steam from the extraction points from the low-pressure part of steam turbine is used....
-
The low temperature waste heat recovery in drying process of pine wood using micro-jet heat exchanger
PublikacjaThe article presents the influence of the drying medium temperature changes for the relative and absolute moisture content values during pine wood drying. The drying process was conducted at constant atmospheric pressure and with different drying medium (air) temperature levels, respectively: 40oC, 60oC, 80oC, 100oC, and 120oC. In order to develop a method that would enable low temperature drying of solid materials the experiments...
-
Managment of low grade waste heat from the supercritical power plant using the ORC cycle aided by bleed steam
PublikacjaW pracy przedstawiono oryginalną koncepcję dogrzewu obiegu ORC za pomocą pary upustowej z nadkrytycznego bloku energetycznego.
-
Multi-objective optimization of the ORC axial turbine for a waste heat recovery system working in two modes: cogeneration and condensation
PublikacjaDue to the demand of the district heating network and electric power grid ORC turbines can operate in the condensation and cogeneration modes. This approach requires the design of an expander which is characterized by high efficiency in each mode of operation. The paper is devoted to a multi-objective efficiency optimization of a one stage axial ORC turbine working on MM (Hexamethyldisiloxane). An Implicit Filtering algorithm (IF)...
-
Zagospodarowanie ciepła odpadowego z biogazowych agregatów kogeneracyjnych w oczyszczalni ścieków = Waste heat utilisation from cogeneration set in sewage plant
PublikacjaW pracy opisano koncepcję współpracy biogazowych modułów kogeneracyjnych z niskotemperaturowym obiegiem parowym. Proponowana modernizacja pozwoliłaby na wykorzystanie entalpii fizycznej spalin, tym samym zwiększając sprawność urządzeń wytwarzających ciepło i energię elektryczną. Tego typu rozwiązanie umożliwiłoby częściowe pokrycie zapotrzebowania własnego na energię elektryczną, generując oszczędności w przedsiębiorstwie. W artykule...
-
Proposal of a mobile medical waste incinerator with automatic waste feeder and heat recovery system
PublikacjaThe paper presents and discusses the issue of medical waste (including hazardous ones) and their proper management. Inappropriate handling of infectious medical waste directly endangers the human being health and the environment. Infectious waste must therefore be properly disposed of – one of the most commonly used methods is the thermal treatment in the incinerators tailored for this purpose. During designing an incinerator unit,...
-
Proposal of a Mobile Medical Waste Incinerator with Application of Automatic Waste Feeder and Heat Recovery System as a Novelty in Poland
PublikacjaThe paper presents and discusses the issues of medical waste (including hazardous ones) and the problems regarding their proper management in Poland. Inappropriate handling of infectious medical waste directly endangers human health and the environment. Infectious waste must be properly disposed of—in practice, the only method of their disposal available in Poland is a thermal treatment in the incinerators tailored for this purpose....
-
Small wood waste fired combined heat and power plant. Possible use of wood biomass for the generation of electric and heat energy as an alternative to fossil fuels
PublikacjaThis article discusses the possibility of burning wood biomass instead of fossil fuels in boilers. It describes the properties of wood biomass, including the variation of its calorific value depending on the moisture content of wood. The article proposes several variants of a combined heat and power plant (CHP) system burning wood biomass for the generation of electric and heat energy, using the energy contained in exhaust gases...
-
Ewa Klugmann-Radziemska prof. dr hab.
OsobyEwa Klugmann-Radziemska ukończyła studia wyższe na kierunku fizyka na Uniwersytecie Gdańskim, a od roku 1996 związana jest z Politechniką Gdańską, kiedy to rozpoczęła studia doktoranckie. Obecnie jest profesorem na Wydziale Chemicznym Politechniki Gdańskiej, od roku 2006 kierownikiem Katedry Aparatury i Maszynoznawstwa Chemicznego. W latach 2008–2016 pełniła funkcję Prodziekana ds. współpracy i rozwoju, w latach 2016-2019 była...
-
A new construction of shell-and-tube heat exchanger with impinging jets and minichannels technologies for heat recovery from gases – experimental analysis
PublikacjaA dynamic development of technologies allowing waste heat utilization is observed in a correspondence with a pro-ecological approach of the zero waste idea. Such approach becomes the most demanding in the area of low-temperature was heat sources, especially gaseous media. Till now, they were usually not utilized due to unfavorable thermal conditions and high costs. Therefore, the zero waste approach directs research on techniques...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaIn the paper presented is a concept to utilize waste heat from the power plant with the aid of the low-temperature ORC cycle. The ORC system is heated from two heat sources, the first one being the flow rate of waste heat obtained from the exhaust gases. Subsequently, the working fluid in the cycle is additionally heated by the condensing steam from the low pressure turbine extraction points increasing in such way the level of...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaThe presented work is aimed at utilisation of waste heat in the manner to produce electricity in ORC installation. Therefore the precondition of the study was to use the waste heat available in the form of a stream of hot water at 90°C. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. That was the incentive to search for the ways of increasing the temperature of the...
-
Bartosz Dawidowicz dr inż.
OsobyAbsolwent Wydziału Budowy Maszyn Politechniki Gdańskiej Mgr inż. - Wydział Budowy Maszyn Politechniki Gdańskiej: specjalizacja: Maszyny i Urządzenia Przemysłu Spożywczego (2000)Dr - Wydział Budowy Maszyn Politechniki Gdańskiej, dyscyplina: budowa i eksploatacja maszyn, specjalność: wymiana ciepła (2008) Zainteresowania naukowe dotyczą m.in. technik wodorowych – ogniwa paliwowe, wykorzystanie wodoru na cele energetyczne, odnawialnych...
-
High-temperature heat pumps – new devices for heat recovery and production of technological steam
PublikacjaIn the paper, the original high temperature compressor based heat pump with a dry working fluid, i.e. the one in which the slope of saturated vapour line is positive, was presented. The objective of the paper is to investigate the possibility of preparation of technological steam with tempperature 120 C from the waste heat resource at temperature of 50 C. Single comppression cycles as well as cascade systems have been considered...
-
Operation of the 900 MW power plant with the ORC supplied from three heat sources
PublikacjaThe chapter is aimed at utilisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90°C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach to increase...
-
Thermal-Hydraulic Studies on the Shell-and-Tube Heat Exchanger with Minijets
PublikacjaIn this paper a patented design of a heat exchanger with minijets, with a cylindrical construction is presented. It is followed by the results of its systematic experimental investigations in the single-phase convection heat transfer mode. Based on these results, validation of selected correlations (coming from the literature) describing the Nusselt number was carried out. An assessment of the heat exchange intensification level...
-
Combined operation of 900MW power plant with the ORC through the bleed steam extraction point and CO2 recovery system
PublikacjaThe work presented here is aimed at utylisation of waste heat in the reference supercritical power plant in the manner to produce electricity in ORC installation. The waste heat is available in the form of a stream of hot water at 90 C, recovered from the exhaust gases in the amount of 200MW. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. Therefore an original approach...
-
THE THERMODYNAMIC ANALYSIS OF THE SZEWALSKI HIERARCHIC VAPOUR CYCLE COOPERATED WITH THE SYSTEM OF HEAT RECOVERY
PublikacjaIn this paper, thermodynamic analysis of the Szewalski hierarchic vapour cycle cooperated with the system of heat recovery from exhaust gases are presented. According to that purpose, the CFM (Computation Flow Mechanics [1,3]) approach has correctly been used. The whole system consists of the first traditional steam cycle, the second organic Rankine cycle (ORC) and system of heat recovery with use of water with temperature 90...
-
Microwave treatment in waste rubber recycling – recent advances and limitations
PublikacjaEnvironmentally-friendly microwave heating is increasingly used in polymer chemistry and technology. The selectivity and highly efficiency in the heat transfer present a huge advantage in systems based on recycling, improving their productivity and economic competitiveness. In case of the industrial recycling of waste rubbers, especially end-of-life tires, microwave-induced devulcanization and pyrolysis are nowadays considered...
-
Efficiency and proportions of waste tyre pyrolysis products depending on the reactor type—A review
PublikacjaThis article discusses the current use of different pyrolytic reactors, their constructions and operating principles regarding the yields of main products of waste tyre pyrolytic recycling. Whether one makes a larger or smaller profit, or even a loss due to a surcharge being levied on waste tyre recycling, depends on the sale of the pyrolysis products (gas, char, oil), the proportions and market prices of which differ. The cheapest...
-
Two-phase optimizing approach to design assessments of long distance heat transportation for CHP systems
PublikacjaCogeneration or Combined Heat and Power (CHP) for power plants is a method of putting to use waste heat which would be otherwise released to the environment. This allows the increase in thermodynamic efficiency of the plant and can be a source of environmental friendly heat for District Heating (DH). In the paper CHP for Nuclear Power Plant (NPP) is analyzed with the focus on heat transportation. A method for effectivity and feasibility...
-
SELECTED COMBINED POWER SYSTEMS CONSISTED OF SELFIGNITION ENGINE AND STEAM TURBINE
PublikacjaThis paper presents optimization of selected combined diesel engine-steam turbine systems. Two systems: the system combined with waste heat one-pressure boiler only and its version containing additionally low-pressure boiler proper feeding degasifier and the system of two-pressure cycle, were taken into considerations. Their surplus values of power output and efficiency associated with utilization of waste heat contained in piston...
-
Application of Thermo-chemical Technologies for Conversion of Associated Gas in Diesel-Gas Turbine Installations for Oil and Gas Floating Units
PublikacjaThe paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are...
-
Pilot installation for thermal utilization of meat-and-bone meal using the rotary kiln pyrolyzer and the fluidised bed boiler
PublikacjaThe technology of thermal utilization of meat-and-bone meal (MBM) is still at the research state. However, there are already a number of existing pilot-scale installations that provide the complete, effective and environmentally safe process conducting. The universal technology was developed that allows to combust various types of waste, including animal waste, municipal waste and sludge, mixed at any ratio with different types...
-
Mechanical Properties, Microstructure and Surface Quality of Polypropylene Green Composites as a Function of Sunflower Husk Waste Filler Particle Size and Content
PublikacjaAgricultural waste is a still untapped source of materials that can, in case of proper utilization, significantly improve the sustainability of polymers and their composites. In this work, polymer composites based on isotactic polypropylene were produced incorporating ground sunflower husk in the amount of 10 wt% and 20 wt%. The work’s main objective is to evaluate how preliminary fractioning of this agricultural waste filler affects...
-
The role of additives in improving the flammability and calorific value of leather shavings and the binding of chromium compounds in ash
PublikacjaLeather processing companies are struggling with the problem of increasing costs of post-production waste disposal. Therefore, the issue of thermal waste disposal at the plant and the use of generated heat in the production process is becoming more and more popular. Leather waste on its own does not allow for autothermal combustion despite the sufficient higher heating value (HHV). Therefore the Authors proposed to improve the...
-
Biochemical assays of intensified methane content in biogas from low-temperature processing of waste activated sludge
PublikacjaAnaerobic digestion (AD) is implemented as an important ‘waste to energy’ approach for converting organic-rich byproducts such as sewage sludge into biogas and nutrient-rich digestate. Sewage sludge consists of primary sludge and waste activated sludge (WAS), and low biodegradability of WAS limits methane production. This study presents the influence of the low-temperature pretreatment (LT-PT) of WAS on the efficiency of AD. Different...
-
Zagospodarowanie ciepła odpadowego z biogazowych agregatów kogeneracyjnych w oczyszczalni ścieków
PublikacjaW pracy opisano koncepcję współpracy biogazowych modułów kogeneracyjnych z niskotemperaturowym obiegiem parowym. Proponowana modernizacja pozwoliłaby na wykorzystanie entalpii fizycznej spalin, tym samym zwiększając sprawność urządzeń wytwarzających ciepło i energię elektryczną. Tego typu rozwiązanie umożliwiłoby częściowe pokrycie zapotrzebowania własnego na energię elektryczną, generując oszczędności w przedsiębiorstwie. W artykule...
-
Comparative analysis of thermodynamic cycles of selected nuclear ship power plants with high-temperature helium-cooled nuclear reactor
PublikacjaThis paper presents a comparative analysis of thermodynamic cycles of two ship power plant systems with a high-temperature helium- cooled nuclear reactor. The first of them is a gas system with recuperator , in which classical gas chamber is substituted for a HTGR reactor (High Temperature Gas-cooled Reactor) . The second of the considered cycles is a combined gas-steam system where working medium flux from gas turbine outlet...
-
Energy Systems Stations, W, ET, sem.7, zimowy 22/23 (PG_00042106)
Kursy OnlineInternal combustion engines - principle of operation and classification. Heat balance of the engine. Uniform and combined propulsion systems.The main comonents of the propulsion system. Power plant efficiency and waste heat utilization. Cooling water system, lubricating oil system, fuel oil systeml, gaseos fuel system (LNG), compressed air system, exhaust gas system. Fittings and accessories of pipeline systems in the power plant....
-
WSPÓŁPRACA BLOKU GAZOWO-PAROWEGO Z OBIEGIEM ORC = Combinded power plant in cooperation with ORC
PublikacjaIn the paper presented is the idea of a combined gas and steam power plant cooperation with a low temperature organic Rankine cycle ORC unit. Considerations presented in the paper are accomplished for the Gorzów CHP. The intention of present analysis is heat recovery of low temperature energy and its further use in ORC cycle in order to produce electricity, without increase in fuel consumption. Waste energy is recovered from the...
-
Challenges in operating and testing loop heat pipes in 500–700 K temperature ranges
PublikacjaThe potential applications of loop heat pipes (LHPs) are the nuclear power space systems, fuel cell thermal management systems, waste heat recovery systems, medium temperature electronic systems, medium temperature military systems, among others. Such applications usually operate in temperature ranges between 500–700 K, hence it is necessary to develop an LHP system that will meet this requirement. Such a thermal management device...
-
Static Model of Steam/Water Cycle for Thermal and Economic Analysis
PublikacjaThe thermodynamic efficiency of typical conventional and nuclear power plants is insufficient. A large amount of the generated heat is removed to the environment and regarded as a waste. A solution which is commonly used to increase the efficiency and profitability of the existing and planned power plants refers to cogeneration of heat and power. To prepare sophisticated thermodynamic and economic analyses, a precise static model...
-
Experimental study of pressure rise at the evaporator of capillary pumped loop with acetone and water as working fluids
PublikacjaIn this work studied is the possibility of fluid pumping using capillary forces in the capillary pumped loop. Experimental and theoretical studies have been performed to understand the phenomena associated with heat transfer in porous structure of the evaporator. The capillary effect was studied during operation of two different capillary porous structures with two different working fluids, namely water and acetone. The results...
-
A Theoretical and Experimental Study of Moderate Temperature Alfa Type Stirling Engines
PublikacjaThe Stirling engine is a device that allows conversion of thermal energy into mechanical energy with relatively high efficiency. Existing commercial designs are mainly based on the usage of high temperature heat sources, whose availability from renewable or waste heat sources is significantly lower than that of moderate temperature sources. The paper presents the results of experimental research on a prototype alpha type Stirling...
-
Possibility to use engine compression ignition engines in floating power plants marine
PublikacjaCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. The engines can be used in power industry for electricity generation in a simple or combined steam turbine system in combined heat and power plants. The leading engine in such an arrangement is an internal-combustion piston engine. The main propulsion engines are used in large piston internal-combustion engines...
-
Feasibility of combined diesel engine - steam turbine in power station operating in the maritime
PublikacjaCompression-ignition engines used in ship technology as main propulsion engines are large units reaching even to 50-60 MW. Currently, the efficiency of such engines amounts to 45-50%. With such a large power unit, exhaust gases leaving the engine contain very large quantities of heat available for further treatment. Exhaust gases from the piston engine contain about 25% of the heat supplied to the engine in the fuel. Using the...
-
Stirling engines - the state of technology development and computational models
PublikacjaStirling engines represent a technologically important solution in combined heat and power systems. Their use enables the achievement of over 90 percent efficiency in the management of the primary energy source with a very high durability of the device, mainly due to the lack of contact of the working gas with external factors and a very small number of mechanical components. The use of a Stirling engine may be equally important...
-
Design analysis of combined gas-vapour micro power plant with 30 kW air turbine
PublikacjaThe article presents basic results of the design analysis of a combined gas-vapour micro power plant with a waste-heat boiler without exhaust reheat, working in the vapour section in the Organic Rankine Cycle (ORC) system. The analysis concerned working media most frequently used in those types of power plants and planned to be used in future. The object of the analysis was a micro power plant with a 30 kW gas (air) turbine for...
-
Design analysis of combined gas-vapour micro power plant with 30 kW air turbine
PublikacjaThe article presents basic results of the design analysis of a combined gas-vapour micro power plant with a waste-heat boiler without exhaust reheat, working in the vapour section in the Organic Rankine Cycle (ORC) system. The analysis concerned working media most frequently used in those types of power plants and planned to be used in future. The object of the analysis was a micro power plant with a 30 kW gas (air) turbine for...
-
Hydraulic resistance analyses of selected elements of the prototype Stirling engine
PublikacjaThe paper presents the results of simulation tests of hydraulic resistance and temperature distribution of the prototype Stirling alpha engine supplied with waste heat. The following elements were analyzed: heater, regenerator and cooler. The engine uses compressed air as a working gas. Analyses were carried out for three working pressure values and different engine speeds. The work was carried out in order to optimize the configuration...
-
Theoretical Organic Rankine Cycle efficiency depending on different thermodynamic work variables.
PublikacjaOne of promising technologies of utilizing low- temperature waste heat is through ORC (Organic Rankine Cycle) system implementation. A primary objective in designing in-stallations based on such systems is to maximize the installation's work efficiency. On the other hand, ecological factors are commonly considered a natural barrier in introducing new, often very expensive technologies. Ecological effect of a potential modernization...
-
Selected aspects of performance of organic Rankine cycles incorporated into bioenergy with carbon capture and storage using gasification of sewage sludge
PublikacjaThe study aims to investigate the application of the Organic Rankine Cycle (ORC) in the bioenergy with carbon capture and storage (BECCS) using gasification of sewage sludge. The tool used in the investigation is the Aspen Plus software with REFPROP property methods for calculating fluid properties. The reason for this study is that a detailed analysis of the proposed BECCS process flow diagram indicates that a certain amount of...
-
Elementary analysis and energetic potential of the municipal sewage sludges from the Gdańsk and Kościerzyna WWTPs
PublikacjaThis paper aims to present municipal sewage sludge (MSS) elementary analysis and energetic potential based on measurement of heat of combustion (higher heating value HHV) and calculation of calorific values (lower heating value LHV). The analysis takes into the consideration water content in sewage sludge, at different utilization stages, in wastewater treatment plants in Gdańsk Wschód and Kościerzyna – Pomeranian Voivodeship....
-
The Course and the Effects of Agricultural Biomass Pyrolysis in the Production of High-Calorific Biochar
PublikacjaThe thermal pyrolysis of agriculture biomass has been studied in a fixed-bed reactor, wherethe pyrolysis was conducted at a steady temperature of 800◦C. This work analyses the pyrolysisproducts of six agricultural wastes: pistachio husks, walnut husks, sunflower hulls, buckwheat husks,corncobs and coconut shells. The conducted research compared examples of large waste biomassstreams from different parts of the world as a potential...
-
Investigation of the Combustion Processes in the Gas Turbine Module of an FPSO Operating on Associated Gas Conversion Products
PublikacjaIn this paper, we consider the issue of thermo-chemical heat recovery of waste heat from gas turbine engines for the steam conversion of associated gas for offshore vessels. Current trends in the development of offshore infrastructure are identified, and the composition of power plants for mobile offshore drilling units and FPSO vessels is analyzed. We present the results of a comparison of power-to-volume ratio, power-to-weight...
-
Vascular stents - materials and manufacturing technologies
PublikacjaThe objective of this article is to present materials and technology for the manufacture of vascular stents with appropriate design requirements. The use of the right material is very important in implantology. A biomaterial introduced into the circulatory system must be biocompatible and hemocompatible. At the same time, it should not initiate toxic, mutagenic, or immunological reactions. Currently, 316L stainless steel (316L...
-
New insights of nanomaterials usage toward superhydrophobic membranes for water desalination via membrane distillation: A review
PublikacjaMembrane distillation (MD) is a promising technology for seawater desalination due to the ability to process high-salinity waters and the ability to be driven by low-grade or waste heat. However, practical applications of MD membranes are limited by the low vapor flux and fouling problem. Recently, there is a growing interest in developing novel MD membrane materials with enhanced hydrophobicity to improve the efficiency of desalination...
-
Assessment of the water quality of Kłodnica River catchment using self-organizing maps
PublikacjaRisk assessment of industrial areas heavily polluted due to anthropogenic actions is of increasing concern worldwide. So is the case of Polish Silesia region where mostly heavy industry like smelters, mining, chemical industries as well as heat and electricity production facilities are being located. Such situation raises numerous questions about environmental state of local water bodies with special attention paid to the Kłodnica...
-
The Environmental Benefits of Photovoltaic Systems: The Impact on the Environment in the Production of Photovoltaic Systems: With a Focus on Metal Recovery
PublikacjaGreenhouse gases (GHGs) such as carbon dioxide, nitrous oxide and methane, trap heat and energy, thus preventing solar radiation from escaping back into space. As the quantity of greenhouse gases in the atmosphere increases so does the trapped heat and corresponding global temperature. As a result, storms become more violent, droughts more prevalent, glaciers melt, and sea levels rise, to name but a few effects of a rapidly changing...
-
Green energy extraction for sustainable development: A novel MPPT technique for hybrid PV-TEG system
PublikacjaThe Photovoltaic (PV) module converts only a small portion of irradiance into electrical energy. Most of the solar energy is wasted as heat, resulting in a rise in PV cell temperature and a decrease in solar cell efficiency. One way to harvest this freely available solar thermal energy and improve PV cell efficiency is by integrating PV systems with thermoelectric generators (TEG). This cogeneration approach of the hybrid PV-TEG...
-
Assessment, optimisation and working fluid comparison of organic rankine cycle combined with negative CO2 gas power plant system
PublikacjaThis study aims to investigate the application of the Organic Rankine Cycle (ORC) as an alternative to low-pressure expansion in the negative CO2 power plant (nCO2PP). The reason for this study is that a detailed analysis of nCO2PP indicates a certain amount of waste heat present in the exhaust gas from the high-to-intermediate pressure gas turbine. Some of this energy can be used by the application of the expansion in a low-pressure...
-
Cleaner energy for sustainable future using hybrid photovoltaics-thermoelectric generators system under non-static conditions using machine learning based control technique
PublikacjaIn addition to the load demand, the temperature difference between the hot and cold sides of the thermoelectric generator (TEG) module determines the output power for thermoelectric generator systems. Maximum power point tracking (MPPT) control is needed to track the optimal global power point as operating conditions change. The growing use of electricity and the decline in the use of fossil fuels have sparked interest in photovoltaic-TEG...
-
How to make membrane distillation greener? A review on environmentally friendly and sustainable aspects
PublikacjaThere is an urgent need for the development of new water resources in order to solve the problem of the world’s growing demand for clean water. Membrane distillation (MD) is a promising alternative to conventional seawater desalination. Although MD itself is often defined as sustainable desalination technology, there are many aspects within the membrane manufacture and process operation that make it far from being green. For instance,...
-
Thermomechanical and Fire Properties of Polyethylene-Composite-Filled Ammonium Polyphosphate and Inorganic Fillers: An Evaluation of Their Modification Efficiency
PublikacjaThe development of new polymer compositions characterized by a reduced environmental impact while lowering the price for applications in large-scale production requires the search for solutions based on the reduction in the polymer content in composites’ structure, as well as the use of fillers from sustainable sources. The study aimed to comprehensively evaluate introducing low-cost inorganic fillers, such as copper slag (CS),...
-
Renewable Energy in the Pomerania Voivodeship—Institutional, Economic, Environmental and Physical Aspects in Light of EU Energy Transformation
PublikacjaIn the era of globalization and rapid economic growth, affecting most world economies, increased production and consumption are leading to higher levels of energy production and consumption. The growing demand for energy means that energy resources from conventional sources are not sufficient; moreover, its production generates high costs and contributes to the emission of greenhouse gases and waste. In view of the above, many...
-
The Influence of the Chemical Composition of Selected Waste Materials from the Production of Copper on the Final Environmental Assessment
PublikacjaThis article presents qualitative and quantitative analysis of the waste produced by KGHM Polska Miedź. The waste has been analyzed according to its chemical composition and balanced in order to be reused and recycled. Special attention has been paid to mining industries producing the biggest amount of waste and ore enrichment businesses generating waste, which isn’t reused nowadays. Laboratory reseach has been conducted on floatation...
-
A mixture of cellulose production waste with municipal sewage as new material for an ecological management of wastes
PublikacjaChemical contaminants present in cellulose production waste and municipal sewage sludge condition the necessity to treat these wastes before they are introduced into the environment. Environmental use of the these wastes appears to be justified owing to the content of organic substances as well as the considerable fertilising value. The aim of the study was to assess chemical composition and ecotoxicity of cellulose production...
-
Pyrolysis Combined with the Dry Reforming of Waste Plastics as a Potential Method for Resource Recovery—A Review of Process Parameters and Catalysts
Publikacja: Emissions of greenhouse gases and growing amounts of waste plastic are serious environmental threats that need urgent attention. The current methods dedicated to waste plastic recycling are still insufficient and it is necessary to search for new technologies for waste plastic management. The pyrolysis-catalytic dry reforming (PCDR) of waste plastic is a promising pro-environmental way employed for the reduction of both CO2 and...
-
Deep learning-based waste detection in natural and urban environments
PublikacjaWaste pollution is one of the most significant environmental issues in the modern world. The importance of recycling is well known, both for economic and ecological reasons, and the industry demands high efficiency. Current studies towards automatic waste detection are hardly comparable due to the lack of benchmarks and widely accepted standards regarding the used metrics and data. Those problems are addressed in this article by...
-
Preliminary Results from the Removal of Phosphorus Compounds with Selected Sorption Material
PublikacjaDue to the resources of phosphorous are limited and are exhausted in the next 30 years the management of the resources is become current issue. Most of the phosphorus compounds is lost forever, because it is discharged with sewage into surface waters, causing eutrophication and in this way causing a further problem and challenge. On the other hand, there is a considerable need for phosphorus compounds, primarily in bioavailable...
-
Carbon dioxide sequestration by industrial wastes through mineral carbonation: Current status and perspectives
PublikacjaMineral carbonation using natural minerals or industrial wastes is a safe and promising strategy for CO2 sequestration. Application of industrial wastes for this purpose has significant ecological and environmental value, which is one of the key green technologies in the global carbon mitigation. This review summarizes the current research status of CO2 mineralization by industrial wastes. This work surveys the mechanisms and capacities...
-
Polyurethane-wood composites (PU-WC) as a method of wood waste management
PublikacjaIn recent years, due to the progressive environmental degradation and increase of environmental awareness, the sustainability of production systems in wood processing, the wood industry, and wood waste management is a crucial issue for European industry and society. Consequently, the problem of generating wood-like waste and the associated risks has become an increasingly noticeable challenge for science. Although various methods...
-
Waste management in the mining industry of metals ores, coal, oil and natural gas - A review
PublikacjaWaste generated due to mining activity poses a serious issue due to the large amounts generated, even up to 65 billion tons per year, and is often associated with the risk posed by its storage and environmental management. This work aims to review waste management in the mining industry of metals ores, coal, oil and natural gas. It includes an analysis and discussion on the possibilities for reuse of certain types of wastes generated...
-
MINERAL MATTER IN MUNICIPAL SOLID WASTE
PublikacjaMunicipal solid waste (MSW) contains mineral materials which are seldom considered as a potential resource. Currently, the waste management sector pays attention to recyclable parts, biodegradable material, waste-to-energy fraction, and residues after waste reuse and recycle. In contrast, this study focus as on the mineral matter in MSW. The aim was to analyze and discuss the sources of mineral matter in MSW, the impact which the...
-
Sustainable utilization of copper post-flotation waste in cement composites
PublikacjaThe current way of managing the copper ore flotation waste is by placing it in waste neutralization facilities. However, flotation waste has great potential in application in cement composites. The article presents the detailed characteristics of post-flotation waste (PFW) and three types of cements: CEM I, CEM II/B-V, and CEM III/A, 42.5 MPa class. The post-flotation waste added for 20% of the cement mass increase the water demand...
-
The influence of rubber recyclate morphology on the properties of rubber-asphalt composite
PublikacjaIn the paper wastes, mostly in the form of used tires, were analyzed. One of the methods of waste tires application use them as a modifier of asphalt. However, the properties of rubber-asphalt composites depend on the morphology of waste tiregranulate and kind of tire recycled (car/truck). In this chapter, the influence of grinding methods of waste tire on the prop¬erties of rubber-asphalt composites were studied. SEM analysis...
-
From polymer waste to potential main industrial products: Actual state of recycling and recovering
Publikacjalastics have become widely used materials in everyday life due to their special properties such as durability, easy processing, light-weight and low-cost of production. However, because of their stable and non-biodegradable nature, postconsumer plastics become an issue to the environment. The growing amounts of waste are generated, as plastic products are commonly used only once before disposal. The alternatives of practical techniques...
-
Recycled Polyethylene terephthalate (PET) as Construction Material in Civil Engineering: A Review
PublikacjaIn general, the quantity of plastics of all types consumed annually all over the world has been growing in a phenomenal way. The manufacturing processes, service industries and municipal solid wastes (MSW) generate numerous waste plastic materials. The increasing awareness about the environment has tremendously contributed to the concerns related with disposal of the generated wastes. It is believed that the management of solid...
-
Pyrolysis and Torrefaction—Thermal Treatment of Creosote-Impregnated Railroad Ties as a Method of Utilization
PublikacjaA fundamental issue of waste management and the rail transport industry is the problem of utilizing used railroad ties. Wooden railroad ties are treated with a preservative, usually creosote. Due to their high toxicity, railroad ties are considered hazardous waste and must be utilized under various directives. It is proposed to utilize the troublesome waste by using the pyrolysis and torrefaction process. The research proves that...
-
Cement kiln dust
PublikacjaThe volume of cement production in the world has remained at the level of approxi mately 4.1 billion tons/year. The cement production process is energy intensive and is the world’s leading emitter of carbon dioxide. Therefore, the main activities cement plants are aimed at introducing technologies changes in production of clinkier.The construction industry is responsible for the majority of CO2 emissions to the atmosphere: the...
-
Thermal utilization of meat-and-bone meal using the rotary kiln pyrolyzer and the fluidized bed boiler – The performance of pilot-scale installation
PublikacjaThermal utilization of meat-and-bone meal (MBM) is subject to stringent regulations that are meant to provide elimination of any potential pathogens. Incineration as well as other possible routes for thermal conversion of MBM are still at the research state. The universal technology was developed that allows to combust various types of waste organic materials, including animal waste, municipal solid waste and sludge, mixed at any...
-
Reclaimed Rubber/Poly(ε‐caprolactone) Blends: Structure, Mechanical, and Thermal Properties
PublikacjaThe amount of elastomeric waste, especially from tires is constantly increasing on a global scale. The recycling of these residua should be considered a priority. Compounding the waste rubbers with other polymers can be an excellent alternative to reuse waste materials. This procedure requires solving the issue of the lack of compatibility between the waste rubber particles and other polymers. Simultaneously, there is a claim for...
-
Sustainable Waste Management for Implementation of a Circular Economy Model in a Port
PublikacjaThe manuscript presents the management of waste from marine vessels and cargo handling companies in a selected European Union port. The main objective of the paper is to analyse and evaluate the existing waste management model in the port of Szczecin in the context of circular economy. The expert research carried out is aimed, inter alia, at identifying which of the solutions currently in use need to be improved from an environmental...
-
Leveraging food waste for electricity: A low-carbon approach in energy sector for mitigating climate change and achieving net zero emission in Hong Kong (China)
PublikacjaIn recent years, food waste has been a global concern that contributes to climate change. To deal with the rising impacts of climate change, in Hong Kong, food waste is converted into electricity in the framework of low-carbon approach. This work provides an overview of the conversion of food waste into electricity to achieve carbon neutrality. The production of methane and electricity from waste-to-energy (WTE) conversion are...
-
Hydrogen production from wood waste by mean of dark fermentation
PublikacjaThe utilization of wood wastes in clean and green chemistry method like by mean of dark fermentation, is a highly desired solution of waste management. In the article model for the estimation hydrogen potential of wood waste is given. The model has been used to calculate the potential theoretical hydrogen mass that can be produced from wood wastes in Pomerania and Silesia: pine, spruce, fir, beech and oak. In the introduction,...
-
Application of industrial waste as a carbon source for biosurfactants production
PublikacjaBiosurfactants are natural surfactants produced by variety of microorganisms. They are very prospective product due to good biodegradability, low toxicity, good physicochemical properties and high efficiency in many applications. Moreover, they are efficient in wide range of pH, temperatures and salinity. However, the production of biosurfactants is very expensive due to high purification cost. This cost can be minimized by application...
-
Waste Rubber Pyrolysis: Product Yields and Limonene Concentration
PublikacjaTires, conveyor belts, floor mats, and shoe soles form a main-stream of rubber waste. The amount of these used materials continuously increases due to development of the rubber market. Therefore, pro-ecological utilization (i.e., energy recycling instead of burning) and recovering valuable and recyclable materials becomes an urgent necessity. In this regard, this work was devoted to the chemical recycling of selected used rubber...
-
Recycling of Polyurethanes
PublikacjaPolyurethane waste can be recycled by mechanical methods (i.e., grinding and applying as a filler or pressing with a bonding agent) and chemical methods (mainly by e.g., glycolysis, hydrolysis, or aminolysis). There is also possibility to the recover energy from polyurethanes waste (by incineration, gasification, and pyrolysis).
-
Environmental impacts of food waste management technologies: A critical review of life cycle assessment (LCA) studies
PublikacjaFood waste is a serious global problem. Therefore, it is essential to reduce food waste and adopt recycling strategies to minimize its environmental impacts. However, conventional waste disposal methods emit harmful gases such as dioxin, CH4, N2O, and NH3, which contaminate the air and water resources. This work reviews the environmental consequences of food waste based on lifecycle assessment (LCA) techniques using methods such...
-
A modern solid waste management strategy – the generation of new by-products
PublikacjaTo benefit the environment and society, EU legislation has introduced a ‘zero waste’ strategy, in which waste material should be converted to resources. Such legislation is supported by the solid waste hierarchy concept, which is a set of priorities in waste management. Under this concept, municipal solid waste plants (MSWPs) should be equipped with sorting and recycling facilities, composting/incineration units and landfill prisms...
-
Utilization of Gaseous Carbon Dioxide and Industrial Ca-rich Waste for Calcium Carbonate Precipitation: A Review
PublikacjaTechnologies for the management of various types of waste and the production of useful products from them are currently widely studied. Both carbon dioxide and calcium-rich waste from various production processes are problematic wastes that can be used to produce calcium carbonate. Therefore, the purpose of this paper is to provide an overview about the state of the development of processes that use these two wastes...
-
THE USE OF GREEN LOGISTICS ELEMENTS DURING THE CONSTRUCTION OF OFFSHORE VESSELS
PublikacjaThe article is aimed at the presentation referring to the use of green logistics elements during the construction of the offshore vessels in the following aspects: collection, removal and utilisation of any waste that is harmful for natural environment, elimination of the negative impact that such waste can have on natural environment and the search for the optimal solutions as regards these aspects.
-
Digestate Quality Originating from Kitchen Waste
PublikacjaThis paper examines the influence of biomass directed to anaerobic digestion on the quality of digestate, specifically focusing on the presence of undesirable substances, such as plastics, including biodegradable ones. It analyses the susceptibility of selected bioplastics to degradation and addresses the problem of reliable identification of microplastics in both feedstock—directed to anaerobic digestion—and produced digestate....
-
Energy policy and the role of bioenergy in Poland
PublikacjaPrzedstawiono sytuacje energetyczną kraju. Omówiono poszczególne sektory wytwarzania energii oraz zapotrzebowania na energię i paliwa. Omówiono przekształcenia sektorów energetycznych w Polsce na przestrzeni lat 1990-2002. Na tym tle przedstawiono techniczne, ekonomiczne, społeczne i prawne aspekty rozwoju energetyki źródeł odnawialnych a w szczególności opartych o bioenergię. Przedstawiono wnioski dla Polski płynące z dotychczasowych...
-
Phosphorus and nitrogen forms in liquid fraction of digestates from agricultural biogas plants
PublikacjaThe novelty of the presented research is the determination of the nitrogen and phosphorus fraction in the liquid fraction of digestate from agricultural biogas plants. This information is important because it can help in proposing possible further liquid fraction management or developing of new technologies for their purification. The research covered digestates from agricultural biogas plants, obtained from the fermentation of...
-
Simple design criteria and efficiency of hydrodynamic vortex separators
PublikacjaVortex separators are locally applied for waste water treatment in different systems - from storm waste water sewerage to water treatment in fish ponds. However, the methods for separator design presented in the literature are questionable. The paper presents two simple and functional criteria that were employed to construct a laboratory test stand. The test results gave positive feed back on the efficiency of vortex separators.
-
Polypropylene structure alterations after 5 years of natural degradation in a waste landfill
PublikacjaUp to 25% of plastic waste in Europe is still disposed of in landfills, despite recycling efforts. The plastic waste in the landfill plot may be exposed both to abiotic and biotic degradation processes, although it is thought that most of the plastic materials tend to be resistant to biodegradation or biodeterioration even after a long time. To verify if polypropylene (PP) can undergo the process of short-term biodegradation and...
-
Utilization of New Activated Carbon Derived from an Oak Leaves for Removal of Crystal Violet from Aqueous Solution
PublikacjaSignificant negative environmental impact has been noticed at the campus garden of Gdansk University of Technology , Poland, when the withered leaves of Quercus robur Oak Tree (OL) cover large areas at such places. In this regards,an attempt has been made to recycle the most abundant agricultural leaf waste into a high quality local activated carbon (LAC) for use in the decolorizating processes of dye industrial waste- water.
-
THE IMPACT OF GROUND TIRE RUBBER TREATMENT ON THE THERMAL CONDUCTIVITY OF FLEXIBLE POLYURETHANE/GROUND TIRE RUBBER COMPOSITES
PublikacjaWaste car tires are burdensome waste, and their utilization is crucial for the natural environment. In many countries, the primary method of their recycling is energy recovery, performed by simple combustion. However, material recycling is much more effective and significantly more beneficial for the natural environment. It results in the generation of ground tire rubber, which can be used to produce polymerrubber composites. It...
-
Valorization of Bioplastic Waste: A Review on Effective Recycling Routes for the Most Widely Used Biopolymers
PublikacjaPlastics-based materials have a high carbon footprint, and their disposal is a considerable problem for the environment. Biodegradable bioplastics represent an alternative on which most countries have focused their attention to replace of conventional plastics in various sectors, among which food packaging is the most significant one. The evaluation of the optimal end-of-life process for bioplastic waste is of great importance...
-
Waste tire rubber devulcanization technologies: State-of-the-art, limitations and future perspectives
PublikacjaWaste tires management is a serious and global environmental problem. Therefore, searching for low-cost and industrial-scale applicable tire recycling methods is gaining more and more attention. Waste tire rubber is valuable source of secondary raw materials for the circular economy and current trends indicate that application of waste rubbers during manufacturing value-added products should increase in near future. Sustainable...