Wyszukiwarka
Filtry
wszystkich: 925
wybranych: 730
Wyniki wyszukiwania dla: gearbox failures
-
Methodology of experimental research on efficiency of hydro-mechanical automatic gearbox
PublikacjaThe article shortly describes the design and principle of operation of the hydromechanical gearbox and presents the methodology and design of test stands used for testing hydromechanical proto-type gearbox developed at Technical University of Gdansk. The article presents an approach according to which, in order to obtain reliable measurement data, it is necessary to separate the tests of the hydraulic and mechanical parts of the...
-
Condition monitoring of wind turbines based on cointegration analysis of gearbox and generator temperature data
Publikacja -
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublikacjaThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublikacjaDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
THE INFLUENCE OF HOUSING ARRANGEMENT AND INTERFERENCE ON PRELOAD AND THEORETICAL LIFETIME OF A SYSTEM OF TAPER ROLLER BEARINGS OF A HIGH SPEED SHAFT OF A WIND TURBINE GEARBOX
PublikacjaA system of two taper roller bearings can carry loads with a high ratio of axial load to radial load. Such a system was proposed for a wind turbine gearbox following the poor durability of original bearing design with the aim of increasing durability. Because of size limits, a proposed system is composed of two different taper roller bearings. Standard manufacturers’ catalogues do not provide information on recommended preload...
-
Disaster-Resilient Routing Schemes for Regional Failures
PublikacjaLarge-scale natural disasters can have a profound effect on the telecommunication services in the affected geographical area. Hence, it is important to develop routing approaches that may help in circumventing damaged regional areas of a network. This prompted the development of geographically diverse routing schemes and also of disaster-risk aware routing schemes. A minimum-cost geodiverse routing, where a minimum geographical...
-
ANALYSIS OF THE POSSIBILITIES OF HIGH SPEED SHAFT BEARING SYSTEM DURABILITY INCREASE
PublikacjaDuring the operation of wind turbines with a gearbox of traditional configuration, a high failure rate of high-speed shaft bearings is observed. Such a high failures frequency is not reflected in standard bearing durability calculation methods, which can be attributed to atypical failure mechanism. To avoid observed problems in the 1.5 MW wind turbine, the modification of the existing bearing system is proposed. Multiple options,...
-
Environmental failure of dental biomaterials
PublikacjaW pracy przedstawiono problematykę związaną z zagadnieniem trwałości biomateriałów stomatologicznych. Scharakteryzowano kryteria doboru materiałów i na przykładzie koron stomatologicznych pokazano wyniki oceny prawidłowości doboru w oparciu o metodę elementów skończonych. Przedstawiono wyniki weryfikacji doświadczalnej i wskazano na możliwości wykorzystania tej metody do konstruowania odpornych na zniszczenie koron metalowo-ceramicznych.
-
Methods of Springs Failures Diagnostics in Ore Processing Vibrating Screens
Publikacja -
The PARAGON-Heart failure trial – another disappointment for heart failure patients with hypertension and preserved ejection fraction
Publikacja -
Hale systemowe GALBOX wykonane całkowicie z kształtowników giętych na zimno
PublikacjaW artykule przedstawiono hale systemowe Galbox, wykonane z profili giętych na zimno. Zaprezentowano zależność ciężaru hal stalowych dla różnych rozwiązań konstrukcyjnych.
-
Operational causes of fatigue failures within the passages of gas turbine engines
PublikacjaThe short profile of a fatigue wear process of gas turbine engine's constructional elements has been introduced in the article. The primary causes of a fatigue cracks formation within the mechanical system as well as within the passages of the engine have been showed. Especial attention was devoted to the low-cycle fatigue, what is associated with unsteady thermal-flow processes being worked out in the passages.The selected damages...
-
The reliability of any-hop star networks with respect to failures of communication nodes.
PublikacjaThis paper investigated the reliability of any-hop star networks. The any-hop star topology is used in centralized computer networks. We will assume that the all nodes fail independently, links are failure-free. Following measures of network reliability are assumed: the expected number of nodes, which can communicate with the central node; the expected number of node pairs, which are connected by a path through the central node;...
-
Investigation of Anti-Lock Braking System failures using wavelet analysis
Publikacja -
Reliability Testing of Wind Farm Devices Based on the Mean Time to Failures
Publikacja -
Low-Cost Flight Simulator with Possibility of Modeling of Flight Controls Failures
PublikacjaThe goal of this paper is to present a development of a low cost flight simulator, that allows to simulate flight controls failures. Cessna 172 has been chosen as an example of a general aviation aircraft and the flight model has been implemented in Simulink. The model allows for easy integration of an experimental autopilot, using various strategies. Aerodynamic coefficients have been calculated using software called DATCOM. Such...
-
Vibration-Based Diagnostics of Radial Clearances and Bolts Loosening in the Bearing Supports of the Heavy-Duty Gearboxes
Publikacja -
Analisys of the failure of fixator used in bone surgery
PublikacjaThe Gamma nail (fixator) made of stainless steel, which has broken in the body, was subjected to examination. The fixator was removed from the patient femur. The fracture occurred in the area of the nail hole after two months' stay in the organism. The research included chemical composition, hardness of the Gamma nail material and the observation and analysis of the type of fracture. The research showed the fatigue failure of the...
-
ANALYSIS OF THE PUNCHING FAILURE MECHANISM IN WORKING PLATFORMS
PublikacjaPaper presents an analysis of the shear failure mechanism which occurs from the punching of a working platform layer in relation to its thickness, grain size arrangement and mechanical properties, taking into consideration the interaction with soft subgrade. The study is based on the observations of performance of natural scale structures (Streefkerk) and the results of model investigations numerically represented with the use...
-
Failure Analysis of footbridge made of composite materials
PublikacjaFinite element method analysis of a pedestrian footbridge made of sandwich material is presented. The internal structure of the material is modelled as a structural shell assuming the Equivalent Single Layer approach (ESL). Two FEM commercial codes are employed. The response of the structure is studied in order to determine the load level that activates Hashin and Tsai-Wu failure criteria. Some practical aspects of designing footbridges...
-
Pertussis: History of the Disease and Current Prevention Failure
Publikacja -
Creep failure prediction of pipelines in elevated temperature
PublikacjaW pracy omówiono zastoswanie modelu konstytutytwnego pełzania pozwalającego na analizę trwałości metalowych ruruciągów pracujących w wysokich temperaturach. Zaprezentowano wyniki obliczeń opartych na metodzie elementów skończonych (MES) wykonanych z wykorzystaniem procedur użytkownika w komercyjnym programie MES. Porównano wyniki dla dwóch typów 4-węzłowych elementów powłokowych.
-
Increasing rail life by forecasting fatigue failure.
PublikacjaReferat poświęcony jest przedłużaniu żywotności szyn i obejmuje zagadnienia prognozowania liczby pęknięć a także planowania szlifowań szyn. Dane pomiarowe pochodzą z wieloletnich badań przeprowadzonych w Katedrze Inżynierii Kolejowej Politechniki Gdańskiej na liniach magistralnych PKP.
-
Determination of Failure Causes of a Steam Turbine Casing
PublikacjaThe paper presents results of research and failure analysis undertaken to determine failure causes of a steam turbine casing. After 130,000 hours of service the crack in a outer shell of the turbine casing was found. The inner shell of the casing was made of cast steel grade G21CrMoV5-7, and the outer shell of grade G20CrMo4-5. Following research were performed in order to determine causes of the casing failure: chemical analysis;...
-
Biomechanical causes for failure of the Physiomesh/Securestrap system
PublikacjaThis study investigates the mechanical behavior of the Physiomesh/Securestrap system, a hernia repair system used for IPOM procedures associated with high failure rates. The study involved conducting mechanical experiments and numerical simulations to investigate the mechanical behavior of the Physiomesh/Securestrap system under pressure load. Uniaxial tension tests were conducted to determine the elasticity modulus of the Physiomesh...
-
Numerical simulation of laminate composite specimens failure
PublikacjaThis work presents some numerical results concerning simulation of failure of laminate composite specimens. In the article two tests to determine ultimate strength in an orthotropic layer, are considered: tension (TT1) and compression (TC1) test. The outcome is compared with experimental data provided by [9,10].
-
Contribution of dynamic vehicle loads to pavement failure
PublikacjaPavement surfaces are not ideally even, which causes dynamic loads of vehicle axles. Distribution of dynamic loads of a given axle is similar to normal distribution and can be described by static load and dynamic load coefficient. The dynamic load coefficient depends on road profile, vehicle speed, properties of suspensions and static load of axle. While for a given road section road profile remains constant, vehicle speed and...
-
Endoscopic image processing and analysis of pistons' service failures of marine diesel engines
PublikacjaThe paper deals with diagnostic issues concerning endoscopic examinations of working spaces within marine diesel engines. In the beginning, endoscopy apparatus being on laboratory equipment of the Department of Ship Power Plants of Gdansk University of Technology has been characterized. The endoscopy considerations have been focused on theoretical bases of a digital image processing and especially - on the "Shadow" measurement...
-
Entrepreneurial Failure: A Synthesis and Conceptual Framework of its Effects
Publikacja -
Analysis of ship shaft line coupling bolts failure
PublikacjaW artykule przedstawiono dane statystyczne dotyczące uszkodzeń linii wałów okrętowych, w tym także pęknięć zmęczeniowych śrub sprzęgieł kołnierzowych wałów. Wyjaśniono także mechanizm powstawania tego typu uszkodzeń i zagrożenia jakie niosą ze sobą. Opisano przypadki takich uszkodzeń oraz badania jakie są prowadzone dla lepszego poznania zjawisk zmęczeniowych w omawianych uszkodzeniach.
-
An Overview of Several Inhibitors for Alzheimer’s Disease: Characterization and Failure
Publikacja -
Acceptance of the disease and sexual functions of patients with heart failure
Publikacja -
Flow-induced stress corrosion failure of SS piping
PublikacjaPrzedstawiono uszkodzenie eksploatacyjne rurociągu ze stali austenitucznej typu 18Cr-10Ni-Ti w instalacji przepracowanych olejów napędowych w rafinerii ropy naftowej. Wyjaśniono mechanizm niszczenia środowiskowego stali w wyniku mechanicznego i elektrochemicznego działania strumieni procesowych.
-
Measures of region failure survivability for wireless mesh networks
PublikacjaWireless mesh networks (WMNs) are considered as a promising alternative to wired local, or metropolitan area networks. However, owing to their exposure to various disruptive events, including natural disasters, or human threats, many WMN network elements located close to the failure epicentre are frequently in danger of a simultaneous failure, referred to as a region failure. Therefore, network survivability, being the ability...
-
Assessing the failure of Open Government Data initiatives in Brazil
PublikacjaWhile assessing the potential of a particular digital innovation initiative, especially when it has implications for a range of societal stakeholders, it becomes pertinent to understand the possible bottlenecks in its acceptability as well. In this regard, the present study seeks to understand how the Open Government Data (OGD) initiatives in Brazil are being confronted with bottlenecks in terms of their execution and acceptability....
-
FEM simulation of laminate failure in the three point bending
PublikacjaThe paper presents a FEM simulation of failure of laminate subjected to the three point bending. The numeri-cal model is based on the equivalent single layer approach with 6-paramater non-linear shell theory kinematics. It is implemented in the non-commercial FEM code. The failure initiation is detected with the use of Tsai-Wu criterion. After the failure onset the progressive failure process is modelled through the appropriate...
-
Efficiency of service recovery in scale-free optical networks under multiple node failures
PublikacjaIn this paper we examine the properties of scale-free networks in case of simultaneous failures of two networknodes. Survivability assumptions are as follows: end-to-end path protection with two node-disjoint backup pathsfor each working path. We investigate three models of scale-free networks generation: IG, PFP and BA.Simulations were to measure the lengths of active and backup paths and the values of service recovery time.We...
-
Reliability Testing of Wind Farm Devices Based on the Mean Time between Failures (MTBF)
Publikacja -
An overview of the strategies for the deammonification process start-up and recovery after accidental operational failures
PublikacjaThe deammonification process has been universally acknowledged as an energy-efficient technology for sewage disposal. In contrast with traditional biological nitrogen removal technology, the deammonification process is able to remove ammonia from wastewater with the simplest nitrogen removal process because of its advantages of lower operating expenses, no organic carbon consumption, lower biomass production, lower carbon dioxide...
-
Analysis of Failure Mechanism in Joints with Positive Eccentricity in CFS Truss
PublikacjaThe paper presents studies concerning the load-bearing capacity of truss joints with a positive eccentricity resulting from the arrangement of geometric members and the failure mechanisms observed in the joints. Based on the previously conducted experimental study, a numerical model of the tested fragment of the CFS truss with eccentricity in the joint was created and validated. All structural details of the tested truss and the...
-
Assessment of unusual failure in crankshaft of heavy-duty truck engine
PublikacjaThe unusual premature failure of a heavy-duty truck engine crankshaft has been the subject of a rigorous study, and this manuscript describes it in detail. The failure was happened to begin with the growth of the crack from the surface defects, in the form of the clusters of non-metallic inclusions, in the lubrication hole zone of the first main journal, which was the stress concentration zone. A series of experiments including...
-
Failure analysis of the exhaust valve face in diesel marine engine
PublikacjaThe exhaust valve from marine diesel engine which was damaged after 2000 hours of service was investigated. In order to prolong the service time the valve face was cladded with cobalt base alloy using laser technique. After failure microstructural and chemical analyses reviled that cladding process was conducted improperly. The chemical composition of the clad layer was far from the designed one and what more completely inhomogeneous....
-
Zniszczenie korozyjne wymiennika ciepła = Corrosion failure of a heat exchanger
PublikacjaPłytowy wymiennik ciepła ze stali 316L uległ zniszczeniu po trzech latach eksploatacji, wskutek perforacji po czyszczeniu nieodpowiednim środkiem czyszczącym.
-
Impact of WDM Network Topology Characteristics on the Extent of Failure Losses
PublikacjaW artykule dokonano oceny wpływu charakterystyk topologicznych sieci na rozmiar strat po awarii węzła/łącza będącej następstwem ataku. W tym celu wprowadzono współczynnik ATRF. Wyniki badań pokazały, że wykorzystanie standardowej metryki odległości do wyznaczania tras podstawowych prowadzi do istotnego zwiększenia liczby połączeń uszkodzonych w wyniku ataku w porównaniu ze skutkami awarii losowej.
-
Excavation induced cast iron pipeline failure – a numerical study
PublikacjaNumerical study on impact of an unsecured excavation on an underground pipeline. Analysis focused on investigation of pipeline displacement generated by soil movement caused by excavation and heavy traffic. Numerical calculations and soil parameter sensitivity analysis based on Finite Element Method. Some comparisons of results with real-life failure cases.
-
Reducing the Probability of Failure in Manufacturing Equipment by Quantitative FTA Analysis
Publikacja -
Fundamental Schemes to Determine Disjoint Paths for Multiple Failure Scenarios
PublikacjaDisjoint path routing approaches can be used to cope with multiple failure scenarios. This can be achieved using a set of k (k> 2) link- (or node-) disjoint path pairs (in single-cost and multi-cost networks). Alternatively, if Shared Risk Link Groups (SRLGs) information is available, the calculation of an SRLG-disjoint path pair (or of a set of such paths) can protect a connection against the joint failure of the set of links...
-
Experimental study on ultrasonic monitoring of splitting failure in reinforced concrete
PublikacjaThis paper investigates inspection of reinforced concrete elements sensitive to the splitting failure. The behaviour of a reinforced concrete specimen subjected to a tensile stress is considered. The damage detection procedure is based on the ultrasonic wave propagation technique. The piezoelectric transducers are located on both ends of the specimen and the measurements are taken periodically during the incrementally increased...
-
FAILURE OF MAGNETIC FLUID SEALS OPERATING IN WATER: PRELIMINARY CONCLUSIONS
PublikacjaThe article analyses properties of magnetic fluid seals installed in rotary sealing no des which operate in the utility water environment. Seals of this type have been examined as a possible solution to the problem with ship manoeuvring propulsion sealing. The present analysis bases on laboratory durability tests of magnetic fluid seals expo sed to long - term utility water loads, at different water pressures and shaft revolutions....
-
RECODIS: Resilient Communication Services Protecting End-user Applications from Disaster-based Failures
PublikacjaDisaster-based failures can seriously disrupt any communication network, making its services unavailable. Such disruptions may be caused by natural disasters, technology-related failures, or malicious attacks, and they are observably increasing in number, intensity and scale. When network services that are a part of critical infrastructure become unavailable, commercial and/or societal problems are inevitable. The issue of limiting...