Filtry
wszystkich: 2003
wybranych: 1575
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: TDDFT CALCULATIONS
-
A simple approach to heat exchanger sizing optimisation by means of entrophy generation minimisation
PublikacjaIn the paper an attempt is presented to find the method of optimization of microtube diameter with respect to optimal thermal-hydraulic conditions in the single-phase shell-and-tube heat exchangers. The approach is based on consideration of pumping power at the condition of maximum heat transfer by the heat exchanger tube system. In the optimization method the tube diameter is first specified and then appropriate calculations are...
-
Analysis of the selection of low temperature medium for a turbine power plant using ocean thermal energy (OTEC)
PublikacjaThe paper presents the results and conclusions of numerical calculations modelled in the EES program of a closed OTEC cycle. The following mediums were analysed: ammonia, R32, R41, R404a, R407c, R410a, R423a, R500, R502, R507a and R114, R152a, R234fa, R600, R1234yf, R1234ze. Analogous assumptions were adopted as in the ORC cycle with heat regeneration for dry refrigerants without regeneration for wet refrigerants. Each of them...
-
Impact of maintenance of floodplains of the Vistula River on high water levels on the section from Włocławek to Toruń
PublikacjaThis article describes the methodology of hydraulic calculations to estimate the water levels in open channels for steady gradually varied flow. The presented method has been used to analyse the water level on the Vistula River from Włocławek cross-section to Toruń cross-section. The HEC-RAS modelling system has been used for parameterization of the river channel and floodplains, as well as for flow simulation. The results obtained...
-
Development of beltless respiration and heartbeat sensor based on flexible piezoelectric film
PublikacjaThe main goal of this work is to report initial development on a respiration and heartbeat measurement sensor that can be used in continuous monitoring conditions at a minimal impact on the patient. General description of the sensor, consisting of a PVDF film and the bonding layer, is given. Open-circuit voltage generated by the sensor is estimated by analytical and numerical calculations. Analog and digital interface used to extract...
-
Locating and Identifying Ferromagnetic Objects
PublikacjaThe new non-iterative method of determining the dipole moment and location is presented in this paper. The algorithm of an object's localization and identification was achieved by using numerical calculations and approximation method. The arbitrary shapes of an object were assumed in the identification algorithm - axially symmetric spheroid (a prolate and an oblate). Several examples of localization and identification of an object's...
-
Modelling of the viscoelastic properties of the technical fabric VALMEX
PublikacjaThe analysis of the Burgers model used for the constitutive description of the technical fabric VALMEX vis-coelastic behavior is presented. It has revealed that the correctness of the identification depends strongly on the level of the immediate strain taken for calculations. Moreover, it has been proven that the Burgers model can be used for modelling of the viscoelastic properties of the polyester reinforced PVC coated VALMEX...
-
THERMODYNAMIC ANALYSIS OF A GENERATION IV SCWR NUCLEAR POWER PLANT CYCLE
PublikacjaThis article presents a flow and thermodynamic analysis of a Generation IV nuclear cycle. An SCWR (Supercritical water reactor) is a high temperature and high pressure reactor that uses water at a temperature above its thermodynamic critical point as the working fluid. The cycle used for the calculations consists of one interstage superheater and 7 regenerative heat exchangers. Division pressure was optimized in view of the cycle efficiency,...
-
Effect of geometric imperfections on aluminium silo capacities
PublikacjaAn aluminum silo with initial imperfections is analysed. Two types of imperfections are considered. The first one takes the form of local indentations in the shell; their size and range are adopted on the basis of the standard guidelines. The second type is a global imperfection described through the use of its eigenforms and by means of two-dimensional random fields. The calculations are limited to two cases of loading: negative...
-
Diagnostics of historic columns using wave propagation
PublikacjaThis paper presents a numerical analysis of elastic wave propagation in columns of historical buildings for diagnostics purposes. Numerical calculations were performed using the finite element method in the Abaqus software package. The analysis was carried out for three types of brick columns: a full column, a column filled with debris, and a column empty inside. The excitation was in the form of a wave packet and signals of propagating...
-
Evaluation of the Impact of Different Types of Uncoupling on the Processing Capacity of Hump Yards
PublikacjaThe paper considers the issue of evaluating the impact of different types of uncoupling to increase the processing capacity of hump yards to ensure high technical-economic indicators in the conditions of limited capital funds. Moreover it describes the mathematical formulation of the sorting slide. For the mathematical formulation, the sorting slide is taken as a surface that is uniquely projected onto a horizontal plane. Based...
-
Reliability of production machines in the bakery industry – theoretical and practical issues
PublikacjaThe aim of the article is to present probabilistic models, which were then used to analyze the reliability of production machines in the baking industry. The author conducted research in the period from January 2, 2016 to December 31, 2018 regarding the measurement of reliability of a traditional production system based on a probabilistic concept. Due to the limited scope of the article, reliability calculations for a set of thermo-oil...
-
Big Data from Sensor Network via Internet of Things to Edge Deep Learning for Smart City
PublikacjaData from a physical world is sampled by sensor networks, and then streams of Big Data are sent to cloud hosts to support decision making by deep learning software. In a smart city, some tasks may be assigned to smart devices of the Internet of Things for performing edge computing. Besides, a part of workload of calculations can be transferred to the cloud hosts. This paper proposes benchmarks for division tasks between an edge...
-
Analysis of the selection of low-temperature medium for a turbine power plant using ocean thermal energy (OTEC)
PublikacjaThe paper presents the results and conclusions of numerical calculations modelled in the EES program of a closed OTEC cycle. The following mediums were analysed: ammonia, R32, R41, R404a, R407c, R410a, R423a, R500, R502, R507a and R114, R152a, R234fa, R600, R1234yf, R1234ze. Analogous assumptions were adopted as in the ORC cycle with heat regeneration for dry refrigerants without regeneration for wet refrigerants. Each of them...
-
Control of a vapour microturbine set in cogeneration applications
PublikacjaSystems with microturbines are implemented for local generation of heat and electricity. This paper presents the analysis of control concepts for a vapour microturbine set with a generator with permanent magnets, intended to work in small heat and power plants. Control system variants differed by the selection of controlled signals and set parameters. Possible ways of control were discussed and compared with experimentally determined...
-
Deep slot effect in the squirrel-cage induction motors with scalar (V/F) control
PublikacjaQualitative characteristics of the electrical drive considerably depend on identification accuracy of math model parameters. In particular, it is depend on detection accuracy of stator active resistance r1 that is used in calculation of flux linkages, rotary speed in sensorless control systems. Paper provides analysis of influence of stator deep slot effect to stator active resistance value
-
Nieliniowa statyka 6-parametrowych powłok sprężysto plastycznych. Efektywne obliczenia MES
PublikacjaGłównym zagadnieniem omawianym w monografii jest sformułowanie sprężysto-plastycznego prawa konstytutywnego w nieliniowej 6-parametrowej teorii powłok. Wyróżnikiem tej teorii jest występujący w niej w naturalny sposób tzw. stopień 6 swobody, czyli owinięcie (drilling rotation). Podstawowe założenie pracy to przyjęcie płaskiego stanu naprężenia uogólnionego na ośrodek typu Cosseratów. Takie podejście stanowi oryginalny aspekt opracowania....
-
Evaluation of respiration capacity of VF in hybrid constructed wetland systems.
PublikacjaThree VF-beds operating in hybrid constructed wetlands in configuration HF-VF-HF were analysed. These hybrid constructed wetlands provide the II stage biological treatment. They are located in Pommerania voivodship, in Sarbsk, Wiklino and Wieszyno, and their capacities are 29.5, 14.2 and 21.6 m3/d, respectively. The article focuses on performance and operation of VF-CW plants during one year. Based on removal of organic matter...
-
Proposed method for estimating the costs of safety barrier life cycle
PublikacjaToday barrier types are frequently selected for their price with little regard for the total costs the structure will incur over its lifetime. One of the basic tools designed to manage road infrastructure is the life cycle cost method (LCC, Life cycle cost). It sums up the costs to plan, design, build, operate (use and maintain) and decommission a road structure. Having developed dynamically at the turn of the century the method...
-
Method of determining the residual fluxes in transformer core
PublikacjaThe article presents the method of calculating the residual induction in transformer columns. The method is based on measurement of the magnetic induction in selected points around the transformer core. The values of residual induction are calculated as linear combination of the results of measurement.
-
Magnetic field microsensor based on GaAs MESFET
PublikacjaA novel concept of the drain separation design in a horizontally-split-drain GaAs MAGFET sensor, based on epitaxial layer growth, was developed. Proper choice of GaAs/AlAs/GaAs epitaxial layer sequence provided good electrical isolation between the drain regions. The measured leakage current between the drain regions was in the range of nA for up to 2V drain voltage bias difference. Performed analytical and numerical calculations...
-
Influence of heterogeneous air entry pressure on large scale unsaturated flow in porous media
PublikacjaThe paper presents numerical simulations of water infiltration in unsaturated porous media containing coarse-textured inclusions embed- ded in fine-textured background material. The calculations are performed using the two-phase model for water and air flow and a simplified model known as the Richards equation. It is shown that the Richards equation cannot correctly describe flow in the presence of heterogeneities. How- ever, its...
-
Elastic wave propagation for condition assessment of steel bar embedded in mortar
PublikacjaThis study deals with experimental and numerical investigations of elastic wave propagation in steel bars partially embedded in mortar. The bars with different bonding lengths were tested. Two types of damage were considered: damage of the steel bar and damage of the mortar. Longitudinal waves were excited by a piezoelectric actuator and a vibrometer was used to non-contact measurements of velocity signals. Numerical calculations...
-
Optimization of the System for Determining the Volume of Tissue Needed for Breast Reconstruction
PublikacjaThis article presents techniques for reconstructing surfaces and volume calculations using a point cloud generated from 3D imaging. The main objective of this article was to optimize the voxel size for the most accurate representation of the surface of the female breast. We experimented with different methods for determining volume using images from the Intel D435i camera. In addition, we designed application and measurement station...
-
Superconductivity in Bismuth Pyrochlore Lattice Compounds RbBi2 and CsBi2: The Role of Relativistic Effects
PublikacjaSuperconducting properties of two bismuthide intermetallic compounds, RbBi2 and CsBi2, were studied by means of experimental measurements and ab initio calculations. We show that in both compounds, the superconductivity emerges from the pyrochlore Bi lattice and its formation is heavily influenced by relativistic effects. Based on our analysis of the effect of spin–orbit coupling on the electron–phonon coupling, we suggest a possible...
-
FEM ANALYSIS AND EXPERIMENTAL TESTS OF RIGID RISER HANGING SYSTEM
PublikacjaThe article presents the analysis, project, and experimental examination of an original rigid riser for Coil Tubing Pipes. The principle of riser operation is based on the use of friction forces. The research included the FEM analysis of the designed riser, calculations of the required bolt tensions, and checking the effect of the clamping force on stress distribution in the pipeline. The results of computer simulation were verified...
-
Numerical studies on the influence of selected construction features and road conditions on the performance of road cable barriers
PublikacjaCable barriers are commonly used on Polish roads, including motorways and local roads. Their main elements are pre-stressed wire ropes, which are usually anchored at two ends in concrete blocks buried in the soil. In this work numerical studies concerning the influence of selected construction features and parameters of the vehicle motion on the performance of cable barriers were performed. Numerical simulations are a useful tool...
-
Numerical Studies on Propellers in Open Water and behind Hulls aiming to support the Evaluation of Propulsion Tests
PublikacjaA RANS based numerical analysis of propellers can contribute considerably to our understanding of propeller/hull interaction. It may also allow for a review of scaling procedures on results from experimental fluid dynamics (EFD). Using various RANS codes (Fluent, CFX, STAR-CCM+ and FreSCo+) on common test cases the authors first focused on propeller open water (POW) calculations. Next we simulated the propeller hull interaction...
-
New polish catalogue of typical flexible and semi-rigid pavements
PublikacjaThe paper covers the following topics important for the development of the new Polish Catalogue of typical flexible and semi-rigid pavements: reasons for preparing the new issue of the Catalogue of typical flexible and semi-rigid pavements, items introduced in the new issue, organise the terminology related to pavements, design traffic calculations and new equivalent axle load factors,...
-
The analysis of turbine propulsion systems in nuclear submarines
PublikacjaThe article systematises submarines, which are presently in service, according to their propulsion types (both conventional and nuclear), power output, and submersion depth. Contemporary types of propulsion systems installed and used in submarines are discussed. Calculations were performed for the PWR (Pressurized Water Reactor) type nuclear propulsion system and the supercritical turbine propulsion system (supercritical reactor...
-
Sampling Strategies: Statistics of Sampling
PublikacjaEach step of the analytical procedure has a significant influence on the final result of the analysis. In the majority of cases the analytical procedure encompasses sampling because the analysis of the entire object (material) is usually not possible. Thus it is necessary to include the uncertainty related to sampling procedure in the uncertainty budget calculations. In the paper: the most important properties of the analysed...
-
INVESTIGATION INTO INTERFEROMETRIC SONAR SYSTEM ACCURACY
PublikacjaThe results of the accuracy measurements of phase differencing bathymetric sonar (PDBS) system in shallow waters are presented in the article. The measurement results were compared with the theoretical calculations for sonar system accuracy and international standards for hydrographic surveys. The proposed formulas enable to assess a priori sonar system performance using system quality factor (SQF), which takes into account influence...
-
The reactivity of 1,1-dichloro-2,2-di-tert-butyldiphosphane towards lithiated metal carbonyls: a new entry to phosphanylphosphinidene dimers
PublikacjaReactions of [Cp*(OC)3M]Li (Cp* = C5Me5, M = Mo, W) towards t-Bu2P–PCl2 lead to the formation of phosphanylphosphinidene dimers [Cp*(OC)3M(η2-t-Bu2P–P)]2 in fairly good yields. The formation of a tetraphosphorus ligand proceeds via reductive dimerization of t-Bu2P–P units. NMR, X-ray investigations and DFT calculations show that the resulting tetraphosphorus ligand has a structure of dication t-Bu2P+=P–P=P+t-Bu2.
-
Analysis and interpretation of radiometric signals in a liquid-gas bubble flow
PublikacjaThe article presents the analysis of signals from a radiometric system consisting of two scintillation probes and two gamma radiation sealed sources. Calculations and interpretation were carried out for the bubble flow of the water-air mixture in the horizontal pipeline. The analysis of the obtained signals was done in time and frequency domain. In the frequency domain, a range of usable frequencies was identified, which were associated...
-
Quasirelativistic potential energy curves and transition dipole moments of NaRb
PublikacjaWe report on extensive calculations of quasi-relativistic potential energy curves and, for the first time, transition dipole moments including spin-orbit and scalar-relativistic effects of the NaRb molecule. The calculated curves of the 0+, 0-, 1, 2 and 3 molecular states correlate for large internuclear separation with the fourteen lowest atomic energies up to the Na(3s ^2S_{1/2}) + Rb(7s ^2S_{1/2}) atomic limit. Several new features...
-
DYNAMIC RESPONSE OF FORUM GDANSK STRUCTURE DUE TO RAIL TRAFFIC
PublikacjaThe paper presents the study of the impact of vibration induced by the movement of the railway rolling stock on the Forum Gdańsk structure. This object is currently under construction and is located over the railway tracks in the vicinity of the Gdańsk Główny and Gdańsk Śródmieście railway stations. The analysis covers the influence of vibrations on the structure itself and on the people within. The in situ measurements on existing...
-
PROBLEMS OF EXPERIMENTAL DETERMINATION OF COEFFICIENTS OF THE WEAR OF SHIP PIPING SYSTEMS
PublikacjaThe article presents series of considerations relating to experimental evaluation of the reliability of ship piping systems. The aim of this study is to attempt to answer the following questions: What should be the tested element? How to choose the diameter of the tested item? What should be the result of measurements and calculations? How to measure? How to choose the duration of the test? How to choose the sample size and elaborate...
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublikacjaIn the paper are presented the results of calculations using authors own model to predict heat transfer coefficient during flow boiling for carbon dioxide. The experimental data from various researches were scrutinised conducted for a full range of quality variation and wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The work shows the importance of taking into account surface...
-
Discrete convolution based on polynomial residue representation
PublikacjaThis paper presents the study of fast discrete convolution calculation with use of the Polynomial Residue Number System (PRNS). Convolution can be based the algorithm similar to polynomial multiplication. The residue arithmetic allows for fast realization of multiplication and addition, which are the most important arithmetic operations in the implementation of convolution. The practical aspects of hardware realization of PRNS...
-
On a Method of Efficiency Increasing in Kaplan Turbine
PublikacjaThis paper presents a method of increasing efficiency in Kaplan-type turbine. The method is based on blade profile optimisation together with modelling the interaction between rotor and stator blades. Loss coefficient was chosen as the optimisation criterion, which is related directly to efficiency. Global optimum was found by means of Genetic Algorithms, and Artificial Neural Networks were utilised for approximations to reduce...
-
Electrostatic interactions in finite systems treated with periodic boundary conditions: Application to linear-scaling density functional theory
PublikacjaWe present a comparison of methods for treating the electrostatic interactions of finite, isolated systems within periodic boundary conditions (PBCs), within density functional theory (DFT), with particular emphasis on linear-scaling (LS) DFT. Often, PBCs are not physically realistic but are an unavoidable consequence of the choice of basis set and the efficacy of using Fourier transforms to compute the Hartree potential. In such...
-
Studies on the formation of formaldehyde during 2-ethylhexyl 4-(dimethylamino)benzoate demethylation in the presence of reactive oxygen and chlorine species
PublikacjaIn order to protect the skin from UV radiation, personal care products (PCPS) often contain chemical UV-filters. These compounds can enter the environment causing serious consequences on the water ecosystems. The aim of this study was to examine, the effect of different factors, such as UV light, the presence of NaOCl and H2O2 on the formaldehyde formation during popular UV filter, 2-ethylhexyl 4-(dimethylamino)benzoate (ODPABA)...
-
Assessment of Thermal Stresses in Asphalt Mixtures at Low Temperatures Using the Tensile Creep Test and the Bending Beam Creep Test
PublikacjaThermal stresses are leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when the temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature...
-
Soft-mode enhanced type-I superconductivity in LiPd2Ge
PublikacjaThe synthesis, crystal structure, and physical properties (magnetization, resistivity, heat capacity) in combination with theoretical calculations of the electronic structure and phonon properties are reported for intermetallic compounds LiPd2X (X = Si, Ge, and Sn). LeBail refinement of powder x-ray diffraction data confirms that all compounds belong to the Heusler family (space group Fm-3m, No. 225). The lattice parameter increases...
-
Improving the procedure of probabilistic load testing design of typical bridges based on structural response similarities
PublikacjaThis paper concerns load testing of typical bridge structures performed prior to operation. In-situ tests of a two-span post-tensioned bridge loaded with three vehicles of 38-ton mass each formed the input of this study. On the basis of the results of these measurements, an advanced FEM model of the structure was developed for which the sensitivity analysis was performed for chosen uncertainty sources. Three uncorrelated random...
-
Application of the neural networks for developing new parametrization of the Tersoff potential for carbon
PublikacjaPenta-graphene (PG) is a 2D carbon allotrope composed of a layer of pentagons having sp2- and sp3-bonded carbon atoms. A study carried out in 2018 has shown that the parameterization of the Tersoff potential proposed in 2005 by Ehrhart and Able (T05 potential) performs better than other potentials available for carbon, being able to reproduce structural and mechanical properties of the PG. In this work, we tried to improve the...
-
Nierówności pionowe toru kolejowego
PublikacjaOcena jakości geometrycznej toru kolejowego wymaga od zarządców infrastruktury stosowania jednolitych metod pomiarów, obliczania i interpretacji wyników. W tym zakresie należy stosować się do norm europejskich i technicznych specyfikacje interoperacyjności. W artykule przedstawiono podstawowe zagadnienia związane z pomiarem i oceną nierówności pionowych toru kolejowego. Zapisano odchyłki dopuszczalne nierówności pionowych według...
-
Modelling the impact of the agricultural holdings and land-use structure on the quality of inland and coastal waters with an innovative and interdisciplinary toolkit
PublikacjaThe changes taking place in the marine coastal zones are extremely important, as about 40% of the human population currently lives in the coastal areas (within 100 kilometres of the coastline) increasing anthropogenic pressure on the marine ecosystems. Agriculture is a significant source of nutrients to the marine environment that increase hypoxia, eutrophication and may pose a threat to the services provided by ecosystems. In...
-
O projektowaniu ściany szczelinowej
PublikacjaW pracy przedstawiono proces weryfikacji i porównania obliczeń otrzymanych z programu bazującego na metodzie elementów skończonych z wynikami analitycznymi dla analizowanej ściany szczelinowej z przyporą ziemną. Dodatkowo autorzy dokonali krótkiego przeglądu literatury z zakresu ścian szczelinowych.
-
The dynamics of the total outputs of Japanese information and communication technology sectors: A further study
PublikacjaThe purpose of this study is to continue the previous studies which discussed the impacts of the changes of final demands on the total outputs of the Information and Communication Technology (ICT) sectors of the specific country. More specifically, this study aims to conduct a deeper analysis regarding these impacts. This study focuses on the case of Japan. This study employs a demand-pull Input-Output (IO) quantity model, one...
-
Reprezentation of mechanic hysteresis in a railway track using the Preisach model
PublikacjaThis paper presents an implementation of the classic scalar Preisach model to describe the hysteresis phenomenon created in a railway track subjected to lateral (in the horizontal plane) displacements. The principles of the Preisach theory and the scalar mathematical model of the mechanical hysteresis that is based on statistically distributed modified hysteresis operators are briefly presented. This article presents the characteristic...