Filtry
wszystkich: 2242
wybranych: 1785
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: photosynthesis rates
-
Determination of the theoretical and actual working volume of a hydraulic motor
PublikacjaA new methodology of determination of the theoretical and actual working volume of a hydraulic motor based on the characteristics of the delivered flow rate into hydraulic motor vs. the rotational speed at a constant pressure drop in the working chambers is described in this paper. A new method of describing the delivered flow rate into a motor per one shaft revolution as a nonlinear function of the pressure drop in the motor working...
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublikacjaDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
Effective yttrium based coating for steel interconnects of solid oxide cells: Corrosion evaluation in steam-hydrogen atmosphere
PublikacjaThis work describes manufacture, analysis and test of a new well conducting corrosion-protection coating that can be applied on steel types with high chromium content. Electrolytic deposition of yttrium salts is used to form thin (<100 nm) coatings on both flat steel sheets (material: Crofer 22 APU) and its properties are proven on woven wire-meshes (materials from two different sources: SUS316 and SUS316L). The oxide scale on...
-
Using wearable device for biomedical signal acquisition and processing
PublikacjaIn this paper we present the research conducted on synchronous measurements of biosignals. The experiment was conducted to evaluate the possibility of estimating vital signs based on eye tracking. Method: The eGlasses platform was used for acquisition of ECG, respiration rate, eye and pupil movement and blood pressure. Data were acquired in three 5 min. intervals during which a subject was performing certain tasks. The signals...
-
Simulation of Direct-Sequence Spread Spectrum Data Transmission System for Reliable Underwater Acoustic Communications
PublikacjaUnderwater acoustic communication (UAC) system designers tend to transmit as much information as possible, per unit of time, at as low as possible error rate. It is a particularly difficult task in a shallow underwater channel in which the signal suffers from strong time dispersion due to multipath propagation and refraction phenomena. The direct-sequence spread spectrum technique (DSSS) applied successfully in the latest standards...
-
Numerical Simulations for Transonic Flow in Control Valve
PublikacjaResults of numerical simulations for transonic flow in control valve are presented. The valve is the main part of an adaptive pneumatic shock absorber. Flow structure in the valve domain and the influence of the flow non-uniformity in the valve on a mass flow rate is investigated. Numerical simulation results are compared with experimental data.
-
Zmiany w systemach jakości BRC dedykowanych producentom żywności
PublikacjaW artykule przedstawiono zmiany wprowadzone w najnowszych wersjach standardu BRC Food wersja 7 i BRC/IoP wersja 5. Na podstawie danych zamieszczonych w ogólnodostępnym katalogu „BRC Global Standards Directory” dokonano oceny stopnia certyfikacji polskich przedsiębiorstw wg standardu BRC Food. Przeprowadzono analizę liczby akredytowanych jednostek certyfikujących w Polsce z uwzględnieniem stopnia ich wydajności.
-
Does one currency mean one price?
PublikacjaEuropean Monetary Union was expected to have many consequences for the economies of participant countries. Theory suggested that through a higher volume of trade and stronger competition in the Eurozone, a single currency would lead to a reduction in price dispersion. As far as prices are concerned, two effects were expected: an immediate effect due to the technical characteristics of the changeover process, and a long-term one...
-
The role of colloidal and particulate organic compounds in idenitrification and EBPR occurring in a full-scale activatedsludge system
PublikacjaThe aim of this study was to determine the immediate effects of slowly biodegradable substrates on the denitrification capability andphosphate release/uptake interactions for a full-scale biomass process from the ''Wschod'' wastewater treatment plant (WWTP) in Gdansk (Poland). Since it is hard to distinguish the slowlybiodegradable substrate in a direct way, a novel procedure based on batch experiments was developed and implemented....
-
Domestic ORC micro-CHP combined with a commercial gas boiler
PublikacjaThe chapter presents the results of experimental studies conducted during the launch of the first in Poland demonstration prototype of the micro ORC coupled to a domestic gas boiler. The accomplished studies indicated the possibility for the ORC module to work with such boiler (autonomous source of heat) with a prototype single-stage axial micro turbine as the expansion machine. Confirmation of that fact has been delineated in...
-
VUV photofragmentation of the six-membered heterocyclic molecules containing oxygen
PublikacjaCancer is a significant public health concern worldwide, which results in millions of deaths each year. The standard cure routine for cancer is surgery, and nowadays, radiotherapy or a hadrontherapy. Depending on the type of cancer, patients may undergo additional treatment, including targeted therapy. A combination of radio- or hadron-therapy with proper drug treatment can inhibit the proliferation of cancer cells and thus can...
-
Empirical analyses of robustness of the square Msplit estimation
PublikacjaThe paper presents Msplit estimation as an alternative to methods in the class of robust M-estimation. The analysis conducted showed that Msplit estimation is highly efficient in the identification of observations encumbered by gross errors, especially those of small or moderate values. The classical methods of robust estimation provide then unsatisfactory results. Msplit estimation also shows high robustness to single gross errors...
-
Tome-lapse X-ray tomography imaging of flow patterns in versatile silo model
PublikacjaThe paper introduces a new versatile silo model that was especially designed for in situ X-ray tomography studies of silo discharge for various flow conditions, namely concentric and eccentric. The presented work focuses on organic granular materials where low fraction of short-grain white rice is mixed with spheroidal sorghum particles. The high-quality tomography images combined with adequate image processing strategy allows...
-
Performance of the very high-temperature heat pump with low GWP working fluids
PublikacjaTraditional heat pumps are a very attractive pro-ecological solutions for a number of applications, including providing of heating or heat recovery from industrial processes. The application range of heat pumps could be greatly enlarged when the operating temperature would be increased to 130-150°C and/or the temperature lift can be increased to 50-100 K. In the paper, the very high temperature vapour-compressor based single stage...
-
Three phase transient model of wet coal pyrolysis
PublikacjaA one-dimensional transient mathematical model was developed to describe the thermal and flow phenomena during coal pyrolysis in a coke oven. The model was solved numerically using partly implicit methods for gas flow and heat transfer problems. It was successfully validated with industrial-scale measurements of temperature change in the middle-plane of the coke oven chamber. The evolution of temperature and pressure, distributions...
-
A commercial gas boiler fitted with the ORC module as perspective solution for households
PublikacjaIn this paper the applicability of the commercial gas boiler (De Dietrich DTG X23N) coupled with the laboratory prototype micro ORC setup was experimentally studied. The main objective was to determine the working fluid capability to obtain required temperatures of vapour prior to the turbine, attainable heat rates and efficiencies of the whole system. The boiler thermal power was 25 kW. Tests were carried out with a single stage...
-
Influence of external climate on natural ventilation performance in buildings
PublikacjaNatural ventilation is driven by either buoyancy forces or wind pressure forces or their combinations that inherit stochastic variation into ventilation rates [ CITATION Hun99 \l 1045 ]. We now that these factors have influence on air flow speed and thermal comfort inside building. This work examines the relationship between external climate and natural ventilation including thermal comfort. The work tries in the first instance...
-
ARRAY OF MINIJETS – THERMAL AND HYDRAULIC PHENOMENA IN BOUNDARY LAYER
PublikacjaPresented work considers flow and thermal phenomena occurring in the system consisting of minijets array and heated with constant heat flux surface. Numerical analyses, based on the mass, momentum and energy conservation laws, were conducted. Focus was placed on the proper model construction, in which turbulence and boundary layer modelling was crucial. Calculations were done for various mass flow rates. The main calculations were...
-
Adaptive prediction of stock exchange indices by state space wavelet networks
PublikacjaThe paper considers the forecasting of the Warsaw Stock Exchange price index WIG20 by applying a state space wavelet network model of the index price. The approach can be applied to the development of tools for predicting changes of other economic indicators, especially stock exchange indices. The paper presents a general state space wavelet network model and the underlying principles. The model is applied to produce one session...
-
Influence of configurations of the beds on contaminations removal in hybrid constructed wetlands.
PublikacjaThree hybrid constructed wetlands in configuration HF-VF-HF in Poland and one with another configuration VF-HF-Pond in Gremany were analysed. These hybrid constructed wetlands provide the second stage biological treatment. They are located in Pommerania region, in Sarbsk, Wiklino and Wieszyno, and their capacities are 29.7, 18.6 and 24.5 m3/day, respectively. The analysed system in Germany in Waizenfeld (Gemeinde Pommelsbrunn,...
-
Residual current devices in installations with PV energy sources
PublikacjaThe paper presents the principles of residual current devices (RCDs) application in photovoltaic (PV) installations. Provisions of standards in this regard are commented on, in particular, attention is drawn to the lack of obligation to use of RCDs in PV installations. The issue of the shape of the earth fault current and the level of leakage currents in such installations are discussed. These factors influence the selection of...
-
Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses
PublikacjaWire arc additive manufacturing (WAAM) is an additive manufacturing process based on the arc welding process in which wire is melted by an electric arc and deposited layer by layer. Due to the cost and rate benefits over powder-based additive manufacturing technologies and other alternative heat sources such as laser and electron beams, the process is currently receiving much attention in the industrial production sector. The gas...
-
UV-Vis-Induced Degradation of Phenol over Magnetic Photocatalysts Modified with Pt, Pd, Cu and Au Nanoparticles
PublikacjaThe combination of TiO2 photocatalyst and magnetic oxide nanoparticles enhances the separation and recoverable properties of nanosized TiO2 photocatalyst. Metal-modified (Me = Pd, Au, Pt, Cu) TiO2/SiO2@Fe3O4 nanocomposites were prepared by an ultrasonic-assisted sol-gel method. All prepared samples were characterized by X-ray powder diffraction (XRD) analysis, Brunauer-Emmett-Teller (BET) method, X-ray photoelectron spectroscopy...
-
Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites
PublikacjaHybrid aluminium metal matrix composites have the potential to replace single reinforced aluminium metal matrix composites due to improved properties. Moreover, tribological performance is critical for these composites, as they have extensive application areas, such as the automotive, aerospace, marine and defence industries. The present work aims to establish the tribological characteristics of Al7068/Si3N4/BN hybrid metal matrix...
-
Influence of Gd deposition on the oxidation behavior and electrical properties of a layered system consisting of Crofer 22 APU and MnCo2O4 spinel
PublikacjaIn the study, the surface of the Crofer 22APU ferritic steel was modified with gadolinium oxide nanoparticles and a protective-conducting layer consisting of the MnCo2O4 spinel. This system was studied in the context of application in IT-SOFC interconnects. Four types of samples were studied: unmodified steel, steel coated with a manganese-cobalt spinel layer, steel modified with gadolinium oxide nanoparticles, and a system consisting...
-
Treatment of landfill leachate in a constructed free water surface wetland system over a decade – Identification of disturbance in process behaviour and removal of eutrophying substances and organic material
PublikacjaAn 8 ha free water surface wetland system in Örebro, Sweden, which has sediment traps followed by 10 ponds for treatment of landfill leachate in the methanogenic stage, was studied from 2003 to 2012. The wetland was irregularly loaded and the leachate characteristics showed high temporal and spatial variability, so Multivariate Statistical Process Control was chosen as the diagnostic tool for detecting anomalies prior to assessing...
-
Hydrogen degradation of pre-oxidized zirconium alloys
PublikacjaThe presence of the oxide layers on Zr alloys may retard or enhance the hydrogen entry and material degradation, depending on the layer features. This research has been aimed to determine the effects of pre-oxidation of the Zircaloy-2 alloy at a different temperature on hydrogen degradation. The specimens were oxidised in laboratory air at 350°C, 700°C, and 900°C. After, some samples were tensed at 10-5 strain rate and simultaneously...
-
Direct reduction of pellets through hydrogen: Experimental and model behaviour
PublikacjaThis paper presents the hydrogen reduction behaviour of industrial pellets designed for the efficient hydrogen based direct reduction. The pellets were provided with very low non ferrous oxides percentage (0.52 of basicity index) and with the absence on TiO2 oxides. The pellets measured diameters in the range 1.14–1.72 cm and were characterized in terms of porosity, pores size, tortuosity and compression strength. The pellets were...
-
Zastosowanie addytywów w separacji pianowej białek serwatkowych i białek mlecznych
PublikacjaZaproponowano proces separacji pianowej do wydzielania białek ze strumieni poprodukcyjnych przemysłu mleczarskiego Ponadto zaproponowano zastosowanie w separacji pianowej białek serwatkowych i mlecznych addytywów dopuszczonych ustawą do stosowania w żywności. Jako cel pracy przyjęto uzyskanie wyników uzasadniających wybór takich addytywów, które intensyfikują przebieg i polepszają wynik procesu separacji pianowej białek. W części...
-
Korozja w środowisku ropy naftowej. Czynniki i monitorowanie
PublikacjaPrzedstawiono analizy właściwości ropy naftowej z punktu widzenia zawartych w niej czynników korozyjnych oraz ich wpływu na korozję stali w trakcie procesu destylacji ropy naftowej. Krytycznej analizie poddane zostały możliwości oferowane przez współczesne techniki pomiarowe. Wskazano na istotność prowadzenia kompleksowego programu oceny ropy, monitorowania korozji oraz stosowania ochrony inhibitorowej w celu ochrony instalacji...
-
The Transmission Protocol of Sensor Ad Hoc Networks
PublikacjaThis paper presents a secure protocol for a radio Ad Hoc sensor network. This network uses the TDMA multiple access method. The transmission rate on the radio channel is 57.6 kbps. The paper presents the construction of frames, types of packets and procedures for the authentication, assignment of time slots available to the node, releasing assigned slots and slots assignment conflict detection.
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. On the heat transfer surface of heat exchanger the metallic porous layer was created. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Optimization of Wireless Networks for Resilience to Adverse Weather Conditions
PublikacjaIn this chapter, we consider how adverse weather conditions such as rain or fog affect the performance of wireless networks, and how to optimize these networks so as to make them robust to these conditions. We first show how to analyze the weather conditions in order to make them useful for network optimization modelling. Using an example realistic network, we show how to optimize two types of wireless networks: free-space optical...
-
Silicon Oxycarbide-Graphite Electrodes for High-Power Energy Storage Devices
PublikacjaHerein we present a study on polymer-derived silicon oxycarbide (SiOC)/graphite composites for a potential application as an electrode in high power energy storage devices, such as Lithium-Ion Capacitor (LIC). The composites were processed using high power ultrasound-assisted sol-gel synthesis followed by pyrolysis. The intensive sonication enhances gelation and drying process, improving the homogenous distribution of the graphitic...
-
A novel approach exploiting properties of convolutional neural networks for vessel movement anomaly detection and classification
PublikacjaThe article concerns the automation of vessel movement anomaly detection for maritime and coastal traffic safety services. Deep Learning techniques, specifically Convolutional Neural Networks (CNNs), were used to solve this problem. Three variants of the datasets, containing samples of vessel traffic routes in relation to the prohibited area in the form of a grayscale image, were generated. 1458 convolutional neural networks with...
-
Isothermal Calorimetry and Compressive Strength Tests of Mortar Specimens for Determination of Apparent Activation Energy
PublikacjaThe hydration process of cementitious materials involves a thermally activated reaction that depends on the composition of the mixture and the curing temperature. The main parameter affecting the temperature variation of cast-in-place concrete is the apparent activation energy, which can be used for the efficient prediction of the temperature evolution and maturity index of hardening concrete. This paper discusses two methods to...
-
Emission Profiles of Volatiles during 3D Printing with ABS, ASA, Nylon, and PETG Polymer Filaments
PublikacjaIn this short communication we characterize the emission of volatile organic compounds (VOCs) from fused filament fabrication (FFF) 3D printing using four polymer materials, namely polyethylene terephthalate glycol-modified (PETG), acrylonitrile styrene acrylate (ASA), Nylon, and acrylonitrile butadiene styrene (ABS). Detailed emission profiles are obtained during thermal degradation of the polymers as a function of temperature...
-
The impact of ICTs on women’s economic empowerment
PublikacjaIt is widely argued that ICTs enable the inclusion of low-skilled and traditionally marginalized groups, such as women, people with disabilities, and workers at the base of the pyramid (BoP), in the labor market. In this paper, we investigate the determinants of female participation in the labor market in developing countries with a focus on the impact of the use of ICTs on female labor force participation. We conduct a panel study...
-
The Impact of ICTs on Women’s Economic Empowerment
PublikacjaIt is widely argued that ICTs enable the inclusion of low-skilled and traditionally marginalized groups, such as women, people with disabilities, and workers at the base of the pyramid (BoP), in the labor market. In this paper, we investigate the determinants of female participation in the labor market in developing countries with a focus on the impact of the use of ICTs on female labor force participation. We conduct a panel study...
-
Time evolution of Electrochemical Impedance spectra of cathodically protected steel in artificial seawater
PublikacjaUsability of Electrochemical Impedance Spectroscopy data for better cathodic protection control was investigated. Carbon steel – S235JR2 grade specimen were exposed in artificial seawater environment. Samples were polarized and their potentials corresponded to four different cathodic protection degrees. Time evolution of Electrochemical Impedance spectra was investigated. Goodness of fit function (X2) was analysed in terms of proper...
-
Effectiveness of pollutants removal in hybrid constructed wetlands – different configurations case study
PublikacjaIn recent years, an increase in interest in hybrid constructed wetland systems (HCWs) has been observed. The aim of the paper is to compare different HCW configurations in terms of mass removal rates and efficiency of pollutants removal. Analysed data have been collected at multistage constructed wetlands in Poland, which are composed by at least two beds: horizontal subsurface flow (SSHF) and vertical subsurface flow (SSVF). The...
-
PERFORMANCE OF ENDOSCOPIC IMAGE ANALYSIS ALGORITHMS IN LARGE BOWEL VIDEOS PROCESSING
PublikacjaComputer-assisted endoscopy is a rapidly developing eld of study. Many image anal- ysis algorithms exist, achieving very high rates of eciency at processing single endoscopic images. However, most of them were never tested in processing real-life endoscopic videos. In the article such tests of 16 endoscopy image analysis algorithms are presented and dis- cussed. Tests were performed on two real-life endoscopic videos of a human...
-
Bioaugmentation of a sequencing batch reactor with Archaea for the treatment of reject water
PublikacjaIn this study, the bioaugmentation of a sequencing batch reactor (SBR) for the treatment of reject water from wastewater treatment plant was evaluated. For the bioaugmentation step a product containing an enrichment of microorganisms from the Archaea domain was used to enhance the performance of the reactor for treating reject water. The experiment was carried out in two parallel lab-scale sequencing batch reactors. The first one...
-
Ciprofloxacin-modified degradable hybrid polyurethane-polylactide porous scaffolds developed for potential use as an antibacterial scaffold for regeneration of skin
PublikacjaThe aim of the performed study was to fabricate an antibacterial and degradable scaffold that may be used in the field of skin regeneration. To reach the degradation criterion for the biocompatible polyurethane (PUR), obtained by using amorphous α,ω-dihydroxy(ethylene-butylene adipate) macrodiol (PEBA), was used and processed with so-called “fast-degradable” polymer polylactide (PLA) (5 or 10 wt %). To meet the antibacterial requirement...
-
The influence of polymer bearing material and lubricating grooves layout on wear of journal bearings lubricated with contaminated water
PublikacjaThe goal of the present paper is to investigate wear properties of journal sliding bearing operating in the conditions of contaminated water lubrication. Several bearing materials and bearing sleeve designs (differing in the axial grooves position and their shape) were tested experimentally under typical operating conditions in a dedicated test rig, which was equipped with a lubricating system, enabling lubrication with contaminated...
-
A new approach to β-decays studies impacting nuclear physics and astrophysics: The PANDORA setup
PublikacjaTheory predicts that lifetimes of β-radionuclides can change dramatically as a function of their ionization state. Experiments performed in Storage Rings on highly ionized atom have proven nuclei can change their beta decay lifetime up to several orders of magnitude. The PANDORA (Plasmas for Astrophysics, Nuclear Decay Observation and Radiation for Archaeometry) experiment is now conceived to measure, for the first time, nuclear...
-
Reactive deposition of TiNx layers in a DC-magnetron discharge
PublikacjaTiNx layers have been deposited in 'balanced mode' and 'unbalanced mode' of a reactive DC-magnetron plasma (carrier gas argon, reactive gas nitrogen) under different conditions. Discharge power and reactive gas flow have been varied. The layers have been examined by X-ray photoelectron spectroscopy (XPS), X-ray reflectometry (XR), and spectroscopic ellipsometry (SE). The results of the layer analyses were combined with plasma investigations...
-
Effectiveness of various types of coating materials applied in reinforced concrete exposed to freeze–thaw cycles and chlorides
PublikacjaThis study assesses the durability of coated and uncoated concrete surfaces protected with four different coating materials: water-soluble (BW), solvent-based (BR), mineral (MI), and epoxy (EP). The durability assessment includes evaluating the absorption rate of water, pull-off adhesion strength, and coating material thickness. Concrete samples were subjected to immersion in regular water and a 7% urea solution, followed by...