Filtry
wszystkich: 1358
wybranych: 1162
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: 316l steel
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublikacjaTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
Introducing a Computational Method to Retrofit Damaged Buildings under Seismic Mainshock-Aftershock Sequence
PublikacjaRetrofitting damaged buildings is a challenge for engineers, since commercial software does not have the ability to consider the local damages and deformed shape of a building resulting from the mainshock record of an earthquake before applying the aftershock record. In this research, a computational method for retrofitting of damaged buildings under seismic mainshock-aftershock sequences is proposed, and proposed computational...
-
Experimental tests of reinforced concrete deep-beams
PublikacjaThe paper presents results of experimental research of the reinforced concrete deep beam with a spatial arrangement. Tested structural elements consist of the cantilever deep beam loaded on the height and transverse deep beam with hanging on it another one. The analysis includes crack morphology, effort of steel and load distribution. The article verified effectiveness of two different kind of reinforcement in both tested deep...
-
The bridge over Regalia River in Szczecin - design and construction.
PublikacjaNowoclowa Route is the largest projekt in Szczecin, that consists of 11 km of roads 3,3 km bridges and viaducts, including three parallel bridges across Regalica River (the east arm of Odra River), 535 m long, with the spans: 59+90+90+116+116+64m. The bridge structure consist of two steel plate girders composite with reinforced concrete deck slab. The design and the construction of the bridge are described in the paper.
-
The Effect of Long Term Service at Elevated Temperatures on Microstructure Degradation of Austenitic Reformer Tubes
PublikacjaThe paper analyses the relationship between an increase of the inner diameter of tubes made of Manaurite XM cast steel and transformations occurring in their microstructure due to long-lasting operation in methane reformer. Examinations included metallographic analysis with light microscope (LM), scanning electron microscope (SEM) and microanalysis of the chemical composition of precipitates (EDX). It was indicated that there is...
-
Finite element simulation of cross shaped window panel supports
PublikacjaThe aim of the work is to verify suitability of cross-shaped window panel supports for mullion-transom wall systems. The Finite Element Method (FEM) is chosen to determine the behaviour of stainless steel elements under loading. The advanced non-linear numerical simulations are carried out using an implicit FEM software package MSC.Marc. This study is proposed to initiate the comprehensive investigation of mechanical properties...
-
A novel formulation of 3D spectral element for wave propagation in reinforced concrete
PublikacjaThe paper deals with numerical simulations of wave propagation in reinforced concrete for damage detection purposes. A novel formulation of a 3D spectral element was proposed. The reinforcement modelled as the truss spectral element was embedded in the 3D solid spectral finite element. Numerical simulations have been conducted on cuboid concrete specimens reinforced with two steel bars. Different degradation models were considered...
-
Eksperymentalne i numeryczne badania parametrów dynamicznych trybuny stalowej
PublikacjaTrybuny stalowe to konstrukcje, które odnajdują swoje zastosowanie głównie podczas wydarzeń sportowych, koncertów muzycznych oraz innych wydarzeń, którym towarzyszą rytmiczne aktywności widzów i głośna muzyka. Ze względu na smukłość oraz lekkość elementów z jakich wykonana jest konstrukcja trybuny jest ona bardzo łatwo wzbudzana przez ludzi do drgań. Z przeprowadzonej w pracy [4] analizy modalnej wynika, że masa ludzi prowadzi...
-
Design of Inner Gate for CRIST Shipyard Dry Dock
PublikacjaThe paper deals with a removable steel inner gate which was designed to separate two parts of a dry dock of about 70 m in width and 380 m in length. The gate allows for independent assembly of ship structures in two separated parts of the dock. The fore part of the dock can be flooded while the after part is dry. Tthe gate was designed by IDEK Company Ltd in 2011 and it was soon constructed and used by CRIST Shipyard in Gdynia.
-
Effect of elliptical defect orientation on the durability of specimens subjected to cyclic bending
PublikacjaThis work presents the effect of elliptical defects orientation on the durability of specimens made of C45 steel. Three kinds of specimens with elliptical defects in the form of a one-sided notch oriented at different angles 45, 60, and 90 degrees were subjected to cyclic bending (R=-1). The stress state analysis was performed using local and non-local methods to determine an equivalent amplitude of stress, and then the results...
-
Wpływ posuwu nagniatania na chropowatość powierzchni przedmiotów ze stali w stanie utwardzonym
PublikacjaPrzedstawiono wyniki badań eksperymentalnych procesu nagniatania stali twardej (62 HRC) narzędziem ceramicznym (kulką) z dociskiem hydrostatycznym. Analizowano wpływ posuwu nagniatania oraz parametrów poprzedzającej obróbki toczeniem na twardo na stan powierzchni opisanej wybranymi parametrami chropowatości.
-
Iron doped manganese cobaltite spinel coatings produced by electrophoretic co-deposition on interconnects for solid oxide cells: Microstructural and electrical characterization
PublikacjaWe report a systematic microstructural and electrical characterization of iron doped Mn–Co spinel coatings processed by electrophoretic co-deposition of Mn1.5Co1.5O4 and Fe2O3 powders on Crofer 22 APU and AISI 441 steel substrates. Iron addition to Mn–Co spinel coating leads to a reduction of the area specific resistance on both substrates, after 3200 h at 750 °C. The Fe doped Mn–Co coating both leads to a thinner oxide scale and...
-
Non-Linear Analysis of Inter-Story Pounding between Wood-Framed Buildings during Ground Motion
PublikacjaPounding between adjacent buildings during ground motion may result in structural damage or lead to total destruction of structures. The research on the phenomenon has recently been much advanced; however, the analyses have been carried out only for concrete, steel, and masonry structures, while pounding between wooden buildings has not been studied so far. The aim of this paper is to show the results of detailed non-linear seismic...
-
Comparison of strain results at a laser weld notch obtained by numerical calculations and experimental measurements
PublikacjaIn the development of ship structures applying new materials and it’s purposeful placement play an important role. During the last years, especially in a construction of ro-ro type vessels, the usage of novel sandwich structures in cargo decks is profitable. Steel sandwich panel is an innovative solution which at a todays state of development can be used for the construction of any members not taking part in a global bending of...
-
Corrosion process monitoring by AFM higher harmonic imaging
PublikacjaThe atomic force microscope (AFM) was invented in 1986 as an alternative to the scanning tunnelling microscope, which cannot be used in studies of non-conductive materials. Today the AFM is a powerful, versatile and fundamental tool for visualizing and studying the morphology of material surfaces. Moreover, additional information for some materials can be recovered by analysing the AFM's higher cantilever modes when the cantilever...
-
Wpływ nagniatania ślizgowego na chropowatość zewnętrznych powierzchni obrotowych w częściach maszyn
PublikacjaPodano wyniki badań technologicznych nagniatania ślizgowego wałków ze stali C45.Obróbkę przeprowadzono na tokarce CNC z użyciem nagniataka z tensometrycznym pomiarem siły docisku.Zamieszczono wytyczne dla doboru parametrów obróbki według kryterium wymaganej chropowatości powierzchni obrobianej.
-
Kiedy są niezbędne rysunki warsztatowe konstrukcji stalowych
PublikacjaW wielu przypadkach wymagany prawnie zakres rysunkowej dokumentacji projektowej jest nie wy starczający do właściwego wykonania i montażu konstrukcji stalowych. W artykule przedstawiono sytuacje, w których wykonanie rysunków warsztatowych jest niezbędne. Ma to szczególne znaczenie w budownictwie energetycznym.
-
Stability of roof trusses stiffened by corrugated sheets
PublikacjaThe present parametric study is devoted to the stability analysis of a set of trusses stiffened by decking of corrugated steel sheets. For different parameters of corrugated sheets the critical loading of the roof is calculated. In the parametrical analysis the threshold bracing condition of the roof is obtained. Then the geometrically non-linear analysis of trusses braced by corrugated sheets was conducted. As a results of non-linear...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
Effect of shielded electrode wet welding conditions on diffusible hydrogen content in deposited metal
PublikacjaWet welding is the most popular method of joining in water enviroment. During underwater welding, the weldability of steel is limited by the higher cooling rates and hydrogen content in weld metal. Article presents results of preliminary tests on the effects of wet welding conditions on diffusible hydrogen amount. Seven parameters were optimized using a Plackett-Burman plan to get the most relevant variables. These parameters were:...
-
Tweet you right back: Follower anxiety predicts leader anxiety in social media interactions during the SARS-CoV-2 pandemic
PublikacjaRecent research has shown that organizational leaders’ tweets can influence employee anxiety. In this study, we turn the table and examine whether the same can be said about followers’ tweets. Based on emotional contagion and a dataset of 108 leaders and 178 followers across 50 organizations, we infer and track state- and trait-anxiety scores of participants over 316 days, including pre- and post the onset of the SARS-CoV-2 pandemic...
-
Experimental investigations on concrete beams reinforced with CFRP lamellas
PublikacjaPaper presents experimental investigation made on two concrete beams reinforced with internal Carbon Fibre Reinforced Polymer (CFRP) lamellas (i.e. strips, bands). The reinforcement geometrical arrangement was similar as in normal concrete beams reinforced with steel bars and stirrups. The beams were destroyed by the shear forces, as intended. Obtained load-carrying capacities were lower as expected: below 40% of a calculated value....
-
Remote Monitoring System for Impedance Spectroscopy using Wireless Sensor Network
PublikacjaThe architecture of a miniaturized impedanceanalyser with wireless communication module for remoteImpedance Spectroscopy (IS) of anticorrosion coatings ondifficult-to-reach objects (e.g. on the steel construction ofthe bridge) is described in this paper. Some practical aspectsof implementation of a Wireless Sensor Network (WSN) arealso discussed. A low scale, middle range, WSN networkcomposed of a Base Station (BS) with a Personal...
-
Experimental study on plate modal parameters
PublikacjaTest doświadczalny jest częścią systemu diagnostycznego. Autorzy badają wpływ dodatkowej masy na parametry modalne wolno popartej stalowej płytyi. Artykół przedstawia technikę wyznaczania parametrów modalnych dla systemów monitorowania konstrukcji.The experimental test introduced in the paper is the part of the diagnostic system. The authors investigate the influence of the additional mass on modal parameters of simply supported...
-
Magnetic field gradient as the most useful signal for detection of flaws using MFL technique
PublikacjaThe magnetic flux leakage (MFL) technique is extensively used for detection of flaws as well as for evaluation of their dimensions in ferromagnetic materials. However, proper analysis of the MFL signal is hindered by the MFL sensor velocity causing distortions of this signal. Traditionally measured components of the MFL signal are particularly sensitive to the scanning velocity. In this paper, an another signal – the gradient of...
-
Study of displacements of a bridge abutment using FEM
PublikacjaSteel sheet piles are often used to support excavations for bridge foundations. When they are left in place in the permanent works, they have the potential to increase foundation bearing capacity and reduce displacements; but their presence is not usually taken into account in foundation design. In this article, the results of finite element analysis of a typical abutment foundation, with and without cover of sheet piles, are presented...
-
Degradation of metallic implants
PublikacjaPresence of metallic implants made of stainless steels, Co and Ti alloys is sometimes followed by some undesired allergic reactions and inflammatory processes and consequently the necessity of reimplantation.
-
Experimental investigation of joint with positive eccentricity in CFS truss
PublikacjaDue to technological restrictions, in the case of trusses made of CFS open cross-sections, positive eccentricities in the truss joints have become very frequent. Therefore studies concerning the load-bearing capacity of truss joints with positive eccentricity were undertaken. It was assumed that the resistance of cold-formed steel (CFS) open cross-section truss joints located on compression chords and with positive eccentricity...
-
Selected local stability problems of channel section flanges made of aluminium alloys
PublikacjaThe paper addresses the issue of local buckling of compressed flanges of cold-formed thin-walled channel columns and beams with nonstandard flanges composed of aluminium alloys. The material behaviour follows the Ramberg–Osgood law. It should be noted that the proposed solution may be also applied for other materials, for example: stainless steel, carbon steel. The paper is motivated by an increasing interest in nonstandard cold-formed...
-
SHM System of the Roof Structure of Sports Arena “Olivia”
PublikacjaThe paper presents a structural health monitoring system of the Sports Arena “Olivia” in Gdansk, Poland. The system was installed because of doubts about the roof stability due to observed buckling of the steel truss members. The SHM system was based on nonlinear FEM models used for detection of type of near failure modes of the roof. The application of detailed FEM model in current state updated on data from in situ loading testes...
-
Dynamic Nanoimpedance Characterization of the Atomic Force Microscope Tip-Surface Contact
PublikacjaNanoimpedance measurements, using the dynamic impedance spectroscopy technique, were carried out during loading and unloading force of a probe on three kinds of materials of different resistivity. These materials were: gold, boron-doped diamond, and AISI 304 stainless steel. Changes of impedance spectra versus applied force were registered and differences in the tip-to-sample contact character on each material were revealed. To...
-
Improvement of electrochemical action of zinc-rich paints by addition of nanoparticulate zinc
PublikacjaThe influence of nanosized particles on electrochemical action of standard zinc-rich paints by means of SEM as well as potential and impedance measurements has been investigated. The motivation for doing this was to obtain additional electrical connection between the spherical microparticles themselves and zinc particles and steel substrate. Overall zinc content was at the level of 92% by weight. Samples with different concentration...
-
Increasing the lifetime of engineering structures through the use of composite laggings
PublikacjaThe use of composite laggings prevents concrete (chemical and biological) corrosion. Columns coated with composite or reinforced composite are more resistant to negative environmental impact on concrete or steel. The mechanical properties of the reinforced casing also cause that these types of columns are more resistant to lateral forces. The applied casing limits carbonization of concrete and cyclical freezing and thawing with...
-
Multisource model of ship electric field
PublikacjaA steel-hulled ship in sea water produces an electric field around itself. The source of this field are electrochemical processes and ship's cathodic protection. The analysis of the electric field around the ship is important by the reason of the ship's identification and counter-mine protection. The paper presents a simplified model of the ship's multisource electric field, which allows to calculate the electric field distribution...
-
Fatigue life prediction of notched components under size effect using strain energy reformulated critical distance theory
PublikacjaNotch and size effects show significant impact on the fatigue performance of engineering components, which deserves special attention. In this work, a strain energy reformulated critical distance theory was developed for fatigue life prediction of notched components under size effect. Experimental data of different notched specimens manufactured from GH4169, TC4, TC11 alloys and low carbon steel En3B were used for model validation...
-
Spawalność ferrytyczno-austenitycznej stali odpornej na korozję typu dupleks 2205 w warunkach podwodnych
PublikacjaPraca dotyczy problemów spawalności stali odpornej na korozję typu dupleks w warunkach spawania mokrego elektrodami otulonymi i lokalną komorą suchą. Całość rozprawy składa się z dwóch części. Część pierwsza to przegląd literatury, w którym omówiono główne problemy wynikające z przeniesienia procesu spawania pod wodę oraz sposoby minimalizowania negatywnego wpływu środowiska. Część druga jest częścią doświadczalną, zawiera tezę...
-
A contribution to the moss and liverwort flora of the Reberce Nature Reserve at the Przemyśl Foothills (Western Carpathians, Poland)
Publikacja -
Pool boiling of nanofluids on rough and porous coated tubes: experimental and correlation
PublikacjaThe paper deals with pool boiling of water-Al2O3 and water- Cu nanofluids on rough and porous coated horizontal tubes. Commercially available stainless steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate the test heater. The tube surface was roughed with emery paper 360 or polished with abrasive compound. Aluminium porous coatings of 0.15 mm thick with porosity of about 40% were produced by...
-
The geodetic monitoring of the engineering structure – a practical solution of the problem in 3D space
PublikacjaThe study raises the issues concerning the automatic system designed for the monitoring of movement of controlled points, located on the roof covering of the Forest Opera in Sopot. It presents the calculation algorithm proposed by authors. It takes into account the specific design and location of the test object. High forest stand makes it difficult to use distant reference points. Hence the reference points used to study the stability...
-
Building Information Modelling as an opportunity and risk for stakeholders involved in construction investment process
PublikacjaThe requirements to apply Building Information Modelling (BIM) in public investments worldwide are currently very high. Significant interest (sometimes formulated also as a requirement) in BIM technology can be observed also among private investors. Design technology that applies BIM is supported by many private investors due to its numerous advantages. A growing group of construction designers (steel, concrete and reinforced concrete...
-
O kształtowaniu stalowych, wieloprzęsłowych mostów drogowych
PublikacjaW referacie autor przedstawił główne trendy i swoje własne uwagi odnośnie koncepcyjnego projektowania wieloprzęsłowych mostów stalowych. Bazując na zakończonych projektach autor przedstawił teoretyczne i techniczne problemy które wystąpiły podczas projektowania bądź budowy wybranych obiektów mostowych.
-
The EU Tyre Noise Label: The problem with measuring the noise level of only a few of all tyre variants
PublikacjaThe STEER project, described in another Inter-Noise 2022 paper, has evaluated the performance of the noise label of the European tyre label. The major finding was that uncertainties of the tyre/road noise measurements were higher than should be accepted. One of the worst uncertainty sources was found to be the common practice to measure only some tyres of all sizes or variants within a tyre line, to save money. Generally, only...
-
Fatigue resistance investigation of the IC engine MB11 bearings, working under conditions of dynamic unidirectional loadings
PublikacjaThe slide bearing material MB11 fatigue resistance has been investigated with the application of SMOK - test stand in which dynamic unidirectional loadings to the test bearing is generated. Slide bearing layer consists of the bronze MB11 ( Cu Pb22 Sn 3 ) sintered to the steel shell. Each of the tested bearing has been subject to the standard 20-hour test, under conditions of the full fluid lubrication. Methodology of the experiments,...
-
Modelling of in-plane wave propagation in a plate using spectral element method and Kane-Mindlin theory with application to damage detection
PublikacjaThis paper presents results of experimental and numerical analyses of in-plane waves propagatingin a 5 mm-thick steel plate in the frequency range of 120-300 kHz. For such a thickness/frequency ratio,extensional waves reveal dispersive character. To model in-plane wave propagation taking into account thethickness-stretch effect, a novel 2D spectral element, based on the Kane-Mindlin theory, was formulated. Anapplication of in-plane...
-
Dynamic effect of the vehicle passing under lightweight footbridge.
PublikacjaThe paper describes a numerical study of dynamic response of cable-stayed steel footbridge for a big lorry passing underneath. The footbridge is an existing object crossing Wolska street in Warsaw. The structural model of footbridge was verified by dynamic test loading. A numerical study of a vehicle passing under footbridge is presented. 2D and 3D incompressible flow fields are modeled using sliding mesh in transient CFD computation....
-
Sliding bearings with sintered bronze bush lubricated by contaminated water with solid particles – Theoretical and experimental studies
PublikacjaSliding journal bearings lubricated with water coming directly from the environment are a solution used in shipbuilding, pumps and hydropower. However, the working fluid or surrounding water cannot always be filtered because of design limitations, which often causes the problem of premature wear of these sensitive bearings. The research conducted made it possible to assess the wear of sliding bearings lubricated with water containing...
-
Zagrożenia korozyjne stali nierdzewnych w przemyśle spozywczym
PublikacjaPrzedstawiono przyczyny występowania zagrożeń korozyjnych stali nierdzewnych w przemyśle spożywczym. Szczegółowo omówiono mechanizm oraz sposób zapobiegania korozji wżerowej, szczelinowej oraz pękania korozyjnego. Zaprezentowano dokumentację fotograficzną omówionych typów korozji. Wskazano podstawowe problemy związane z doborem materiałów konstrukcyjnych do budowy instalacji w przemyśle spożywczym.
-
REMONTY I PRZEBUDOWY DACHÓW Z ZASTOSOWANIEM ELEMENTÓW LEKKIEJ OBUDOWY
PublikacjaW artykule przedstawiono przykładowe rozwiązania remontów i przebudowy dachów. Omówiono rozwiązania zmiany materiału pokrycia zarówno bez dodawania warstwy izolacyjnej, jak i z ułożeniem dodatkowej warstwy ocieplenia na istniejącej połaci dachowej a także sposób przebudowy dachu, polegający na ustawianiu nowej, lekkiej konstrukcji nośnej dachu, bezpośrednio na istniejącym pokryciu dachu płaskiego.
-
Legislation and Practice of Selected State Aid Issues, According to EU and Polish Law
PublikacjaThe dataset encompasses several tables, each consisting of three elements: legislation, jurisprudence and scientific articles on numerous subjects and economic activities receiving public financial support in the form of state aid instruments. The set includes a subjective list of the most commonly used and/or disputable examples of granting aid, such as for (local) airports and airlines, steel production, shipyards, and coalmines....
-
Wpływ sztywności podpór bocznych na nośność kratownic dachowych
PublikacjaPrzeprowadzono analizę numeryczną wpływu sztywności podpór bocznych kratownicy dachowej na jej nośność w zakresie sprężystym. Zastosowano nieliniową analizę problemu wprowadzając dwa warianty modelu konstrukcji: z imperfekcjami geometrycznymi na podstawie normy PN-90/B-03200 oraz z imperfekcjami obciążeniowymi na podstawie Eurocode 3: Design of Steel Structures . Wyznaczono siły w stężeniach oraz porównano je z odpowiednimi zaleceniami...