Filtry
wszystkich: 679
wybranych: 578
Wyniki wyszukiwania dla: GALVANIC CORROSION
-
Measurement system for nonlinear surface spectroscopy by atomic force microscopy for corrosion processes monitoring
PublikacjaIn addition to traditional imaging the surface, atomic force microscopy (AFM) enables wide variety of additional measurements. One of them is higher harmonic imaging. In tapping mode the nonlinear contact between tip and specimen results in higher frequency vibrations. More information available from the higher harmonics analysis proves to be helpful for more detailed imaging. Such visualization is especially useful for heterogeneous...
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublikacjaThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
Impedance monitoring of corrosion degradation of plasma electrolytic oxidation coatings (PEO) on magnesium alloy
PublikacjaImpedance technique based on continuous multisinusoidal current perturbation was used to explain degradation process of plasma electrolytic oxidation coatings (PEO) on magnesium alloy. An obtained impedance spectrum was fitted by electrical equivalent circuit to describe properties of conversion layer on magnesium alloy. Additionally, galvanostatic mode maintained during experiment, with DC current equal to zero, allowed to achieve...
-
Influence of electropolymerization temperature on corrosion, morphological and electrical properties of PPy doped with salicylate on iron
PublikacjaIn this work, the influence of the electropolymerization temperature on corrosion, morphological and electrical properties of polypyrrole (PPy) film is studied. Polypyrrole is electrochemically synthesized on iron in the presence of sodium salicylate. The X-ray diffraction and scanning electron microscopy are performed in order to study the structure and morphology of electrodeposited PPy. The electroactive surface area, corrosion...
-
Evaluation of organic coating systems for corrosion protection of industrial equipment using impedance spectroscopy
PublikacjaThe high economic impact of corrosion can be reduced by enhanced corrosion management and prevention based on appropriate means. This applies in particular to the protection of structures with organic protective coatings. Steel is subject to corrosion that reduces its service life and leads to destruction in most severe cases. The application of paints to metallic objects for corrosion control has been known for a long time and...
-
Aspects of intergranular corrosion of AISI 321 stainless steel in high-carbon-containing environments
PublikacjaPurpose – The purpose of this paper is to present a case study of unexpected sensitization to intergranular corrosion of highly resistant AISI 321 steel in petrochemical conditions, where it was subjected to the simultaneous influence of elevated temperature of 250°C and vapors from the asphalt production process. Design/methodology/approach – Corrosion coupons were exposed in an installation carrying asphalt vapors. To identify...
-
Investigation effect of benzotriazole on the corrosion of brass-MM55 alloy in artificial seawater by dynamic EIS
PublikacjaW pracy przedstawiono wyniki badań impedancyjnych otrzymanych podczas ekspozycji stopu MM55 w środowisku sztucznej wody morskiej. Wykazano ścisłą korelację charakterystyk impedancyjnych ze stężeniem benzotriazolu. Przedstawiono czasową ewolucję ochronnego efektu inhibicyjnego.
-
Corrosion resistance evaluation of Al-based alloys by means of dynamic electrochemical impedance spectroscopy
PublikacjaW pracy przedstawiono wyniki badań stopów aluminium wykonane za pomocą dynamicznej elektrochemicznej spektroskopii. Na podstawie uzyskanych widm impedancyjnych zostały pokazane zmiany parametrów elektrycznego schematu zastępczego z potencjałem. Stwierdzono, że dodatek magnezu do badanego stopu obniża właściwości przeciwkorozyjne stopu.
-
Instantaneous impedance evaluation of dissolution of aisi 304 stainless steel during intergranular corrosion
PublikacjaCelem pracy było uzyskanie informacji dotyczących zróżnicowania parametrów elektrycznych uzyskanych na podstawie zarejestrowanych chwilowych widm impedancyjnych w zakresie aktywacji i reaktywacji roztwarzania wysokostopowej stali austenitycznej AISI podczas postępującego procesu korozji międzykrystalicznej. Badania prowadzono z wykorzystaniem dynamicznej elektrochemicznej spektroskopii impedancyjnej (DEIS). Pomiary wykonywano ''on-line''...
-
Non-destructive inspection of anti-corrosion protective coatings using optical coherent tomography
PublikacjaW artykule przedstawiono zastosowanie optycznej tomografii koherentnej (OCT) do badania antykorozyjnych powłok ochronnych. Omówiono właściwości optycznej interferometrii niskokoherentnej jako zastosowanej metody pomiarowej, opisano budowę pomiarowego systemu OCT, zbudowanego w Katedrze Metrologii i Optoelektroniki WETI PG. Przy pomocy zrealizowanego systemu przebadano grupę powierzchni metalicznych pokrytych różnymi powłokami antykorozyjnymi....
-
Corrosion behaviour of Cr coatings deposited from Cr(III) formate - urea electrolytes
PublikacjaPowłoki chromowe były otrzymane z elektrolitów Cr(III) zawierających odpowiednie ligandy, zapewniające ich dobry wygląd. Zbadano wpływ hydrazyny oraz hydrohylo aminofosfatu na właściwości korozyjne Cr otrzymanego z kąpieli mocznikowo-formaldehydowych Cr(III). Właściwości warstw testowano przy pomocy metody EIS rejestrując widma impedancyjne dla próbek o różnych czasach ekspozycji w zakwaszonym roztworze siarczanowym ( pH 2,6) stosując...
-
Evaluation of corrosion inhibition of brass -118 in artificial seawater by benzotriazole using dynamic EIS
PublikacjaPrzedstawiono wyniki korozji mosiądzu 118 w sztucznej wodzie morskiej oraz efekt inhibicyjny benzotriazolu (BTA) przy użyciu nowoczesnej dynamicznej elektrochemicznej spektroskopii impedancyjnej (DEIS). metoda ta pozwala śledzić dynamikę procesu korozyjnego i efektu inhibicyjnego poprzez ocenę parametrów elektrycznych obwodu zastępczego. Chwilowe widma impedancyjne rejestrowane przez 10h wykazują iż ekspozycja przez okres kilku...
-
The Influence of Microstructure on the Passive Layer Chemistry and Corrosion Resistance for Some Titanium-Based Alloys
PublikacjaThe effect of microstructure and chemistry on the kinetics of passive layer growth and passivity breakdown of some Ti-based alloys, namely Ti-6Al-4V, Ti-6Al-7Nb and TC21 alloys, was studied. The rate of pitting corrosion was evaluated using cyclic polarization measurements. Chronoamperometry was applied to assess the passive layer growth kinetics and breakdown. Microstructure influence on the uniform corrosion rate of these alloys...
-
Numerical modelling and analysis of steel specimens subjected to marine immersed corrosion and tensile load
PublikacjaThe present study develops numerical models to analyse the behaviour of steel specimens subjected to marine immersed corrosion degradation and tensile load. The finite element method with the use of the explicit dynamic solver LS-DYNA, satisfying the quasi-static conditions, is employed. Two numerical models are developed, where in the first one, the scans of surfaces gathered from corroded plate specimens are implemented directly...
-
Accelerated large scale test set-up design in natural corrosion marine environment
PublikacjaThe standards for conducting small-scale specimen tests are well developed, but there is a lack of direct guidelines for conducting corrosion tests for large-scale specimens. The objective here is to develop a methodology which may be used in designing an accelerated corrosion test of large-scale structural components subjected to a natural corrosion marine environment. Different factors influencing corrosion degradation of steel...
-
Functionalization of graphene oxide coatings with phosphorus atoms and their corrosion resistance in sodium chloride environment
PublikacjaIn this work, we compared corrosion resistance of graphene oxide, and phosphorus functionalized reduced graphene oxide coatings obtained as a result of electrophoretic deposition on the copper substrate. Doping graphene oxide with phosphorus atoms was performed by a hydrothermal method in the presence of different amounts of phosphoric acid. Structural studies confirmed the insertion of phosphorus atoms into the graphene oxide...
-
Microbiological corossion of metallic products as a result of biofilm
PublikacjaWarunkiem do pojawienia się korozji mikrobiologicznej jest utworzenie na powierzchni metalu biofilmu. Zawiera on biologicznie czynne mikroorganizmy wraz z produktami ich przemian metabolicznych. Biofilm ogranicza dyfuzję produktów metabolizmu wytwarzanych przez poszczególne komórki mikrokolonii. Powoduje to, że produkty uboczne tych przemian gromadzą się w bezpośrednim sąsiedztwie metalu. Gdy powierzchnia metalu nie jest odporna...
-
Corrosion-erosion damage of heat exchanger tubes by desalted crude oil flowing at shell side.
PublikacjaRurki wymiennika zostały uszkodzone lokalnie przez odsoloną ropę naftową przepływającą pod ciśnieniem 2,6 MPa i w temperaturze 385-395K. Większość powierzchni rurek nie była uszkodzona i była pokryta osadem związków organicznych i nieorganicznych, zabezpieczającym przed uszkodzeniami. Badania wykluczyły możliwość występowania intensywnej korozji elektrochemicznej na powierzchniach rurek pozbawionych osadu. Przyczyną perforacji...
-
Correlation between destruction of the metal surface caused by pitting corrosion and intensity of the observed electrochemical noise.
PublikacjaPrzedstawiono wyniki badań korelacji między intensywnością szumów elektrochemicznych obserwowanych podczas występowania procesów korozji wżerowej a zmianami obserwowanymi na powierzchni metalu.Badania przeprowadzono dla elektrod metalowych o powierzchni eksponowanej na środowisko korozyjne poniżej 1 mm2. Do wykrywania uszkodzeń powierzchni wykorzystano oprogramowanie MatLab, wykrywające uszkodzenia powierzchni metalu w formie okręgów...
-
Corrosion-erosion damage of heat exchanger tubes by desalted crude oil flowing at shell side
Publikacja -
Effect of the Post-Weld Surface Condition on the Corrosion Resistance of Austenitic Stainless Steel AISI 304
PublikacjaSurfaces of welded elements made of corrosion-resistant (stainless) steels develop temper colours. The removal of thickened oxide layers off steels exposed to temperatures below 300°C is necessary and entails the restoring of high corrosion resistance of the stainless steel. The article presents tests concerned with the effect of a method applied to remove post-weld temper on the corrosion resistance of austenitic stainless steel...
-
A measurement system for nonlinear surface spectroscopy with an atomic force microscope during corrosion process monitoring
PublikacjaIn addition to traditional imaging the surface, atomic force microscopy (AFM) enables wide variety of additional measurements. One of them is higher harmonic imaging. In tapping mode the nonlinear contact between tip and specimen results in higher frequency vibrations. More information available from the higher harmonics analysis proves to be helpful for more detailed imaging. Such visualization is espe-cially useful for heterogeneous...
-
Fabrication, Microstructure and High Temperature Corrosion Resistance of Porous Alloys for Solid Oxide Fuel Cells
PublikacjaPorous alloys find use in modern Solid Oxide Fuel Cells as the supporting structures. As they are exposed to high temperatures (> 500°C) an oxide scale forms on their surface due to high temperature corrosion phenomena. Since the ratio between the surface area and volume is much higher than for planar samples, formation of the oxide can lead to a breakaway oxidation after relatively short times. Therefore corrosion properties of...
-
Effect of Functionalization of Reduced Graphene Oxide Coatings with Nitrogen and Sulfur Groups on Their Anti-Corrosion Properties
PublikacjaElectrophoretic production of anticorrosion carbonaceous coatings on copper could be successfully performed by anodic oxidation of negatively charged graphene platelets suspended in an aqueous solution. The various platelets were synthesized by Hummer’s method followed by a hydrothermal reduction in the presence of NH4SCN which was expected to substitute some parts of graphene structure with nitrogen and sulfur groups. X-ray photoelectron...
-
Aqueous Molybdate Provides Effective Corrosion Inhibition of WE43 Magnesium Alloy in Sodium Chloride Solutions
PublikacjaCorrosion and corrosion inhibition of WE43 magnesium alloy were investigated in NaCl solutions containing different amounts of sodium molybdate. Electrochemical, microscopic, and spectroscopic experiments were utilized to examine the mechanism of corrosion inhibition by molybdates. Electrochemical data showed that Na2MoO4 inhibitor provides reliable inhibition at concentrations at and above 100 mM. Raman and XPS spectroscopy demonstrated...
-
High Temperature Corrosion Evaluation of Porous Hastelloy X Alloy in Air and Humidified Hydrogen Atmospheres
PublikacjaIn this work a commercially available porous Hastelloy X alloy is characterized in terms of high temperature corrosion resistance. The alloy was oxidized in the temperature range from 500C to 900C in air and humidified hydrogen for 100 hours. Corrosion rates and porosity changes were measured. Microstructural characterization was performed using X-ray diffractometry and scanning electron microscopy. Results show that porous alloys...
-
Critical analysis of laboratory measurements and monitoring system of water-pipe network corrosion-case study.
PublikacjaCase study of corrosion failure of urban water supply system caused by environmental factors was presented. Nowadays corrosion monitoring of water distribution systems is an object of major concern. There is possibility of application broad range of techniques like gravimetric and electrochemical. Both kinds of techniques can be applied in laboratory and field conditions. In many cases researches limit the case analysis to measurements...
-
The inhibition effect of mad Honey on corrosion of 2007-type aluminium alloy in 3.5% NaCl solution
PublikacjaThe inhibition effect of mad honey on corrosion of 2007-type aluminium alloy in 3.5% NaCl solution was investigated by Tafel extrapolarisation (TP), electrochemical impedance spectroscopy (EIS) and dynamic electrochemical impedance spectroscopy (DEIS). All the studied parameters exhibited good anti-corrosive properties against corrosion of 2007-type aluminium alloy in the test solution; the corrosion rates decreased with the increase...
-
Investigation of corrosion behavior of 6060 and 6082 aluminum alloys under simulated acid rain conditions
PublikacjaInstantaneous impedance changes of 6060 and 6082 type aluminum alloys in pure water, and simulated acid rain poured into the pure water was investigated by dynamic electrochemical impedance spectroscopy (DEIS). In this way, the influence of aluminum content on the corrosion behavior of 6060 and 6082 type aluminum alloys immersed in simulated acid rain was determined. The corrosion rate of the alloy decreased with increasing Al...
-
Experimental and Quantum Chemical Evaluation of 8-Hydroxyquinoline as a Corrosion Inhibitor for Copper in 0.1 M HCl
PublikacjaThe corrosion inhibition properties of 8-hydroxyquinoline (8-HQ) in 0.1 M HCl for copper have been investigated by using experimental (electrochemical impedance spectroscopy (EIS), dynamic electrochemical impedance spectroscopy (DEIS), and potentiodynamic polarization) and theoretical methods complemented by surface morphological examination with the aid of scanning electron microscopy (SEM) and electron dispersive X-ray spectroscopy...
-
Assessment of copper surface coverage with corrosion inhibitor using AFM-based local electrical measurements
PublikacjaThe paper presents a new method of assessment of metal surface coverage with corrosion inhibitor and thus of inhibitor protective performance. It is based on the atomic force microscopy measurement performed in a contact mode. Apart from topography images the proposed approach allows acquisition of local DC maps and local electrical impedance spectra via application of DC bias voltage or AC perturbation signal between the conductive...
-
THE COST ANALYSIS OF CORROSION PROTECTION SOLUTIONS FOR STEEL COMPONENTS IN TERMS OF THE OBJECT LIFE CYCLE COST
PublikacjaSteel materials, due to their numerous advantages - high availability, easiness of processing and possibility of almost any shaping are commonly applied in construction for carrying out basic carrier systems and auxiliary structures. However, the major disadvantage of this material is its high corrosion susceptibility, which depends strictly on the local conditions of the facility and the applied type of corrosion protection system....
-
Report vconcerning corrosion reasons of s/y Lunar hull surface and possible way of repair
PublikacjaDokonano oceny korozji kadłuba jednostki pływającej, przyczyn powstania korozji oraz zaproponowano sposoby naprawy miejsc skorodowanych.
-
Microstructure and corrosion properties of the (Mn-N-O-P) type layers created on aluminium alloys
PublikacjaPrzedstawiono mikrostrukturę i właściwości korozyjne warstw powierzchniowych typu (Mn-N-O-P) wytworzonych na stopach aluminium. Wykazano, iż warstwy (Mn-N-O-P) podwyższają wielokrotnie odporność korozyjną stopów aluminium i mogą być stosowane jako warstwy ochronne na tych materiałach.
-
High temperature corrosion of steel equipment in modern rafinery environments with high and low sulphur content
PublikacjaPrzedstawiono charakterystykę i mechanizmy procesów wysokotemperaturowej korozji elementów ze stali we współczesnych rafineriach ropy naftowej podczas eksploatacji we frakcjach węglowodorowych o niskiej i wysokiej zawartości siarki. Zwrócono uwagę na procesy korozji siarkowej w obecności wodoru i bez obecności wodoru oraz proces pylenia metalu pod wpływem węgla ze środowiska - w wypadku niskiej zawartości siarki w środowisku.
-
Surface and Corrosion Properties of AA6063-T5 Aluminium Alloy in Molybdate-containing Sodium Chloride Solutions
PublikacjaCorrosion properties of aluminium alloy AA6063-T5 were investigated in molybdate-containing NaCl solutions. Electrochemical, microscopic, and spectroscopic experiments were utilized to examine the mechanism of corrosion inhibition by molybdates. SEM-EDX, magnetic force, and intermodulation electrostatic force microscopy data suggested that the inhibition initiation preferentially occurred over Fe-rich cathodic IMPs. Spectroscopic...
-
A methodology for ultimate strength assessment of ship hull girder accounting for enhanced corrosion degradation modelling
PublikacjaThe presented work shows a methodology for the ultimate strength assessment of a ship hull, considering enhanced corrosion modelling. The approach is based on the classical Smith method. However, the recent findings regarding the impact of corrosion degradation on ultimate strength are incorporated. To this end, the stress–strain relationships for particular elements composing ship hull cross-section are modified using a specially...
-
Evaluation of adhesion strength, corrosion, and biological properties of the MWCNT/TiO2 coating intended for medical applications
PublikacjaMulti-wall carbon nanotube (MWCNT) coatings are gaining increasing interest because of their special properties used in many science fields. The titania coatings are known for their improvement of osteoblast adhesion, thus changing the surface architecture. Bi-layer coatings comprising 0.25 wt% of the MWCNTs and 0.30 wt% of titania (anatase structure) were synthesized in a two-stage procedure using the electrophoretic deposition...
-
Application of multisine nanoscale impedance microscopy to heterogeneous alloy surface investigations
PublikacjaIn the recent years atomic force microscopy is recognized as valuable tool for investigation of surficial features of construction materials. It concerns, among other things, studies of changes caused by such phenomena as galvanic corrosion, passivation associated with the growth of oxide layers, or sensitization of austenitic steels with the formation of carbide phases. In addition, atomic forcemicroscopy allows easy coupling...
-
Evaluation of cavitation erosion–corrosion degradation of mild steel by means of dynamic impedance spectroscopy in galvanostatic mode
Publikacja -
The analysis of the influence of the corrosion protection method of selected steel elements on the steel structure life cycle costs
PublikacjaSteel products are widely used in the construction for the performance of essential and additional elements of engineering structures. They are characterized by high tensile strength, compression and bending, the structure homogeneity, the possibility of assembly regardless of the season and climatic conditions, ease of processing and the possibility of almost any shape. The main disadvantage of steel structures is their high susceptibility...
-
Electrochemical investigations on the corrosion behaviour of reinforcing steel in diatomite- and zeolite-containing concrete exposed to sulphuric acid
PublikacjaCorrosion is a major concern for most structural applications. Its detrimental effect significantly reduces the life of metallic components. This paper presents the results of an experimental investigation of corrosion in the steel reinforcement of concrete samples having three different substituents: 20% diatomite, 20% zeolite, and a reference without zeolite or diatomite. All concrete specimens were subjected to a solution of...
-
Effect of Thermal Shock During Legionella Bacteria Removal on the Corrosion Properties of Zinc-Coated Steel Pipes
PublikacjaThe purpose of this investigation was to conduct the failure analysis of a water-supply system made from zinc-coated steel. The observed corrosion process had an intense and complex character. The brownish deposits and perforations were present after 2-3 years of exploitation. The electrochemical study based on the Tafel polarization, corrosion potential monitoring, and electrochemical impedance spectroscopy together with microscopic...
-
Instantaneous impedance monitoring of AA 7075 aluminum alloy corrosion in borate buffer with admixed chloride ions
PublikacjaThe study presents a research capabilities of Dynamic Electrochemical Impedance Spectroscopy (DEIS) as a tool used for instantaneous on-line monitoring of corrosion processes on the example of AA 7075 aluminum alloy. A borate buffer with admixed chloride ions in a quantity ranging from 0.05 to 25 mM was used to represent different types of corrosion attack. The surface of samples specimens was evaluated before and after the tests...
-
Instantaneous Impedance Analysis of Non-Stationary Corrosion Process: a Case Study of Carbon Steel in 1M HCl
PublikacjaThe paper concerns the problem of evaluation of stationarity of carbon steel corrosion in 1M HCl. Comparison of corrosion rate with addition of corrosion inhibitor to the reference measurement is the most often used way of evaluating inhibitor efficiency. Such an approach is valid only if corrosion rate is a stationary process. Two complementary techniques were used simultaneously: volumetric analysis of evolved hydrogen and instantaneous...
-
Complex Corrosion Properties of AISI 316L Steel Prepared by 3D Printing Technology for Possible Implant Applications
Publikacja -
Effect of plasma nitriding process on the fatigue and high temperature corrosion resistance of Inconel 740H nickel alloy
Publikacja -
Evaluation of cavitation erosion-corrosion degradation of mild steel by means of Dynamic Impedance Spectroscopy in galvanostatic mode
PublikacjaPrzedstawiono wyniki badań degradacji stali węglowych na skutek oddziaływania erozji-korozji kawitacyjnej. Do analizy wykorzystano technikę Dynamicznej Elektrochemicznej Spektroskopii Impedancyjnej w trybie galwanostatycznym, bliżej odwzrorowującym warunki naturalne. Do oceny stopnia degradacji posłużyły również funkcja ubytku masy MDPR oraz obrazy mikroskopowe SEM. Potwierdzono wpływ łączonej degradacji erozyjno-korozyjnej na...
-
Corrosion resistance examinations of Ti6Al4V alloy with the use of potentiodynamic method in Ringer`s and artificial saliva solutions
PublikacjaThe research results of corrosion resistance of the Ti6Al4V alloy in the simulated body fluids (SBF) are presented. The polished specimens have shown better corrosion resistance than grinded surfaces in both liquids. The artificial saliva has revealed more aggressive test solution than Ringer`s solution. The pitting tendency has been observed in Ringer`s solution for grinded specimens.
-
Corrosion Inhibition Mechanism and Efficiency Differentiation of Dihydroxybenzene Isomers Towards Aluminum Alloy 5754 in Alkaline Media
PublikacjaThe selection of efficient corrosion inhibitors requires detailed knowledge regarding the interaction mechanism, which depends on the type and amount of functional groups within the inhibitor molecule. The position of functional groups between different isomers is often overlooked, but is no less important, since factors like steric hinderance may significantly affect the adsorption mechanism. In this study, we have presented how...