Filtry
wszystkich: 1757
wybranych: 1367
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: MCREYNOLDS CONSTANTS.
-
On-Line Partitioning for On-Line Scheduling with Resource Conflicts
PublikacjaWithin this paper, we consider the problem of on-line partitioning the sequence of jobs which are competing for non-sharable resources. As a result of partitioning we get the subsets of jobs that form separate instances of the on-line scheduling problem. The objective is to generate a partition into the minimum number of instances such that the response time of any job in each instance is bounded by a given constant. Our research...
-
Simultaneous Removal of Al, Cu and Zn Ions from Aqueous Solutions Using Ion and Precipitate Flotation Methods
PublikacjaThis paper presents the results of investigations concerning the simultaneous removal of Al(III), Cu(II), and Zn(II) from dilute aqueous solutions using ion and precipitate flotation methods. The effects of initial solution pH, surface active substance concentration, and the gas velocity on the flotations’ efficiency and course are studied. Experimental results are discussed in terms of physicochemical aspects related to aqueous...
-
The σ-phase superconductors Nb20.4Rh5.7Ge3.9 and Nb20.4Rh5.7Si3.9
PublikacjaWe show that the previously unreported ternary σ phases Nb20.4Rh5.7Ge3.9 and Nb20.4Rh5.7Si3.9 are both superconductors with Tc values of approximately 1.9 K. The superconducting transitions were characterized through temperature-dependent magnetic susceptibility, electrical resistance, and specific heat measurements. The Sommerfeld constants, γ, for Nb20.4Rh5.7Ge3.9 and Nb20.4Rh5.7Si3.9 are 89(1) mJ mol-f.u.−1K−2 and 86(1) mJ mol-f.u.−1K−2...
-
Dead-Time Effect Compensation Based on Additional Phase Current Measurements
PublikacjaThis paper proposes a new method of dead-time effect compensation. The proposed solution is based on additional phase current measurements realized by analog-to-digital converters. These measurements are carried out at the time instants specified by a pulsewidth-modulation (PWM) strategy. This makes it possible to estimate inverter currents at the commutation instants and, finally, to estimate the voltage error caused by dead time. This...
-
Effect of Nb and Al on in vitro dissolution behavior and structure of Na2O-MgO CaO-P2O5 glasses
PublikacjaIn vitro dissolution, structure, and thermal properties of the glass series Na2O-MgOsingle bondCaOsingle bondNb2O5 -Al2O3-P2O5 were studied. The dissolution behavior in phosphate-buffered saline (PBS) confirmed the potential bioactive properties of tested glasses. The dissolution process was found to depend on the Al, Nb, and Mg contents. Al, respectively, suppresses the Nb and accelerates the Mg release process from the glasses....
-
Study on Strategy in University Laboratory Class Teaching
PublikacjaLaboratory teaching is a critical way to ensure the effective input of techniques in engineering learning. Laboratory teaching not only contributes to improving course quality but also helps enrich comprehensive engineering application ability. However, there are some typical problems in current university laboratory teaching, such as rigid and isolated course design, outdated contents and materials, and not encouraging innovation...
-
Mineral and Organic Matter Constituents in Weak Interfaces in Shales
PublikacjaThis paper identifies formation interfaces that would appear to be "weak interfaces", in the Jurassic, Early- Cretaceous Vaca Muerta formation, in the Neuquén Basin, Argentina. Significant distribution of the weak interfaces was observed including contacts between volcanic ash layers of varying thicknesses, calcite-filled veins, and contacts between lithology changes, such as between argillaceous mudstone and mottled carbonates....
-
ANALIZA POSTAW INTERNAUTÓW WOBEC MARKI W MEDIACH SPOŁECZNOŚCIOWYCH
PublikacjaCelem opracowania jest ukazanie roli, jaką odgrywają media społecznościowe i wypowiedzi internautów w kształtowaniu wizerunku marki wśród użytkowników Sieci. Artykuł prezentuje także wyniki obserwacji aktywności polskich internautów dotyczące jednej z polskich marek spożywczych. Internauci zamieszczają w Internecie różnorodne treści powiązane pośrednio lub bezpośrednio z markami. Zadaniem organizacji, podobnie jak w przypadku pozostałych...
-
A new approach to active noise and vibration control - [Part II: unknown frequency case]
PublikacjaThis paper presents a new approach to rejection of complex-valued sinusoidal disturbances acting at the output of a discrete-time stable linear plant with unknown and possibly timevarying dynamics. It is assumed that both the instantaneous frequency of the sinusoidal disturbance and its amplitude may be slowly varying with time and that the output signal is contaminated with wideband measurement noise. It is not assumed that a...
-
A study of the electronic states of pyrimidine by electron energy loss spectroscopy
PublikacjaThe electron energy loss spectra were measured in pyrimidine at the constant electron residual energy varied from 15 meV to 10 eV and in the scattering angle range 0–180°. The spectra were analysed applying an iteration fitting procedure to resolve the energy loss bands corresponding to excitation of the electronic states of pyrimidine. The vertical excitation energies of the singlet states of pyrimidine and of a number of the...
-
Sulfur compounds: Gas chromatography
PublikacjaSulfur compounds, due to their properties, are responsible for the damage of our environment. For this reason sulfur containing compounds are of constant concern in many fields. Gas chromatography (GC), due to combination of separation capability and sensitive detection is a prime technique for the analysis of thes compounds in various matrices. The chapter rewies general problems of the determination of these compounds by GC and...
-
Small rov to detection and identification of dangerous underwater objects
PublikacjaA small unmanned underwater vehicle (UUV) to inspection of an undersea space is presented in the paper. Its behavior is controlled by a trained pilot. Correct detection and identification of targets depends on vehicle'sprecise displacement along a predefined route. Nowadays, the UUVs are equipped with an automatic control system to execute some basic maneuvers without constant human interventions. Hence, in the paper, an autopilot...
-
Fuel systems of high power stationary engine
PublikacjaThe use of alternative fuels and, in the future, synthetic fuels has forced changes in the design of fuel supply systems in internal combustion engines. When operating a stationary engine at constant load, the possibility of using lean fuel mixtures appears. The selection of a precise operating mixture ignition system requires changes in traditional fuel systems. The article presents the current designs of fuel supply systems and...
-
Influence of the Square Wave Voltage on Dynamical Properties of a Flat Voltammetric Electrode in the Time Domain by the Electrochemical Reversible Reaction
PublikacjaIn this article there is a presentation of the analysis of the polarizing voltage shape influencing dynamic properties of voltammetric electrodes when on their surface reversible reaction takes place in the time domain. The electrode polarization with linearly increasing voltage and with a square component, was analyzed. The analysis that were conducted showed that the voltammetric electrode behaves like a first order transducer....
-
Research on the wear evenness of the tool in flat lapping
PublikacjaIn this paper, the dimensionless distribution of the material removal stock and the trajectories of abrasive grains cutting in single-sided lapping process are presented. They were numerically simulated based on the tribological model and kinematics equations. It can be observed that the trajectories geometry of single abrasive as well the velocities have a great influence on the final geometrical deviation. During machining, the...
-
Errors of a Linear Current Approximation in High-Speed PMSM Drives
PublikacjaCurrent sampling techniques and predictive algorithms used in the digital control of electric drives rely on a simple mathematical model that assumes linear current changes upon constant supplying voltages. This paper identifies rotor movement as a factor that makes this assumption invalid when the rotor covers an angular distance of a few tens of degrees during the control interval duration. The errors of the linear current approximation...
-
Navier number and transition to turbulence
PublikacjaThe motivation behind this article is to explain a role of the Navier number (Na -dimensionless slip-length) in prediction of closures for laminar to turbulent transition undergoing via eddies detachment from the slip layer in nano-cannals. Additionally the role of the Navier number Na in universal modeling of phenomenon of enhanced mass flow rate reported in micro- and nano-channels has been explained. The Na number should be...
-
An advanced Thermal-FSI approach to flow heating/cooling
PublikacjaActually, two-way thermal-energy exchange between working fluid and solid material of a casing is a leading problem for modern – semi automatic – design techniques. Many questions should be solved, especially, the turbulent mode of thermal energy transport both in fluid and solid, should be re-examined and reformulated from the primary principles. In the present paper, a group of researchers from Energy Conversion Department of...
-
TIME-DOMAIN NUMERICAL EVALUATION OF SHIP RESISTANCE AND MOTION IN REGULAR WAVES BY USING THE CFD URANS METHOD
PublikacjaTaking into account the International Maritime Organisation’s (IMO) strategy to radically reduce the GHG emitted by the shipping industry towards zero emission operation, today's assessment of ship behaviour in waves, its seakeeping characteristics and resistance and their interrelation with fuel consumption and emissions are one of the most attended research subject. There are three methods to conduct this analysis, which are...
-
Numerical Modelling of Forced Convection of Nanofluids in Smooth, Round Tubes: A Review
PublikacjaA comprehensive review of published works dealing with numerical modelling of forced convection heat transfer and hydrodynamics of nanofluids is presented. Due to the extensive literature, the review is limited to straight, smooth, circular tubes, as this is the basic geometry in shell-and-tube exchangers. Works on numerical modelling of forced convection in tubes are presented chronologically in the first part of the article....
-
PROPELLER INVESTIGATIONS BY MEANS OF NUMERICAL SIMULATION
PublikacjaThe analyses of hydroacoustics are of high interest at the moment due to strong impact of hydroacoustic phenomena on marine environment; the noises, generated e.g. by marine traffic, may be harmful for sea life. The analyses presented here are focused on one of main sources of noises generated by ships, i.e. cavitating propeller. The goal of the work is the assessment of the cavitation phenomenon, carried out with the standard...
-
Możliwości wydłużania krzywych przejściowych w układach geometrycznych torów
PublikacjaW pracy przedstawiono analizę problemu wydłużania krzywych przejściowych, wykorzystując do tego celu analityczną metodę projektowania. Podstawę analizy stanowiły obliczenia numeryczne przeprowadzone dla zestawu parametrów charakteryzujących standardowy układ geometryczny: krzywa przejściowa – łuk kołowy – krzywa przejściowa (w wersji niesymetrycznej). Ocenie poddano różnice rzędnych poziomych układu istniejącego oraz układu z...
-
LOKALIZACJA OBIEKTÓW BUDOWLANYCH W SĄSIEDZTWIE LINII 110 kV
PublikacjaW artykule omówiono wymagania przepisów w zakresie dopuszczalnych wartości pola elektrycznego i magnetycznego niskiej częstotliwości. Przedstawiono wyniki obliczeń rozkładu pola elektrycznego metodą ładunków stymulowanych i w programie FEMM dla przykładowej lokalizacji obiektu przemysłowego w sąsiedztwie linii 110 kV.
-
Mushroom Toxins
PublikacjaToxins and Other Harmful Compounds in Foods provides information on the contents, distribution, chemical properties, and biological activity of toxins and other harmful compounds in foods that are natural components of the raw materials, accumulated due to microbial actions and environmental pollution, or are generated due to processing.
-
Effects of deviations from thermo-rheologically simple behavior of asphalt mixes in creep on developing of master curves of their stiffness modulus
PublikacjaThe paper presents the deviations from the thermo-rheologically simple behavior of asphalt mixes and their effects on the developing of master curves of stiffness modulus. Eleven different mixes were tested in three point bending test under constant load at temperatures –20°C, –10 °C and 0 °C, and in some cases at +10 °C. The test method was developed at the Gdansk University of Technology, Poland. The applied stress level was...
-
Kinetic characterization of hydrogen sulfide inhibition of suspended anammox biomass from a membrane bioreactor
PublikacjaThe inhibition effects of hydrogen sulfide (H2S) on anammox-enriched biomass from a laboratory membrane reactor were analyzed in a series of batch respirometric experiments. The determined half maximal inhibitory concentration (IC50) was 4.67 mg H2S-S L−1 at the constant pH = 7.0 and the total sulfide concentration varying between 1 and 15 mg TS-S L−1. In another test, the IC50 was found to be 4.25 mg H2S-S L−1 under a constant...
-
Organic matter removal efficiency in treatment wetlands simulation by COD fractions
PublikacjaThe objective of this paper was to investigate the organic fraction (colloidal, particulate, and dissolved) in sewage treatment in treatment wetland. Performance of TWs was simulated well with a simple first order model k – C* based on monitoring data. In this investigation background or residual concentration (C*) was assumed to be equal concentration of input influent organic matter in particulate (CODp). Calculated reaction...
-
Measuring the density of DNA films using ultraviolet-visible interferometry
PublikacjaIn order to determine a proper value for the density of dry DNA films we have used a method based upon the measurement of interference effects in transmission spectra of thin DNA layers. Our results show that the methodology is effective and the density of DNA in this state, 1.407 g/cm3, is much lower than the commonly used 1.7 g/cm3. Obtaining accurate values for the DNA film density will allow the optical constants for DNA to...
-
EVOLUTIONARY MULTI–OBJECTIVE WEATHER ROUTING OF SAILBOATS
PublikacjaThe paper presents a multi-objective method, which optimises the route of a sailboat. The presented method makes use of an evolutionary multi-objective (EMO) algorithm, which performs the optimisation according to three objective functions: total passage time, a sum of all course alterations made during the voyage and the average angle of heel. The last two of the objective functions reflect the navigator’s and passenger’s comfort,...
-
Reliable Multi-Stage Optimization of Antennas for Multiple Performance Figures in Highly-Dimensional Parameter Spaces
PublikacjaDesign of modern antenna structures needs to account for multiple performance figures and geometrical constraints. Fulfillment of these calls for the development of complex topologies described by a large number of parameters. EM-driven tuning of such designs is mandatory yet immensely challenging. In this letter, a new framework for multi-stage design optimization of multi-dimensional antennas with respect to several performance...
-
Waveform design for fast clutter cancellation in noise radars
PublikacjaCanceling clutter is an important, but computation-ally intensive part of signal processing in noise radars. It is shown that considerable improvements can be made to a simple least squares canceler if minor constraints are imposed onto noise waveform. The proposed scheme is potentially capable of canceling clutter in real-time, even for high sampling rates.
-
Strategie miast powiatowych na obszarze peryferyjnym województwa pomorskiego.
PublikacjaArtykuł nawiązuje do badań problemów rozwoju obszarów peryferyjnych (czyli poza obszarami metropolitalnymi) prowadzonych przez autora od 2009 r. Postawił on hipotezę, że rozwój miast powiatowych może zaktywizować gospodarczo ich otoczenie. W 2013 r. zbadał czynniki rozwojowe wskazane w planach strategicznych miast powiatowych na obszarze peryferyjnym województwa pomorskiego, obecnie - strategie tych miast w części dotyczącej rozwoju...
-
Analysis of the design development of the sliding table saw spindles
PublikacjaProducers of sliding table saws constantly strive for improvement in sawing accuracy. One of the method is an upswing in a spindle behavior, since, it affects to a large degree sawing effects. The design development of sliding table saw spindles during the last quarter-century is presented. The spindle system of the modernized spindle of the sawing machine Fx550 is described.
-
Elctrochemical oxidation and corrosion resistance of the Ti13Nb13Zr alloy
PublikacjaThis paper presents the results of oxidation and corrosion tests carried out on titanium alloy Ti13Nb13Zr. The oxide film was prepared by electrochemical environment 2M H3PO4 for 30 min and 1 h, at a constant voltage 40V. The tests of corrosion resistance were performed by potentiostatic method in Ringer's solution at different pH values: 7, 5 and 3. The change in an appearance of surface and the increase in corrosion resistance...
-
Problem of proper decomposition and initialization of acoustic and entropy modes in a gas affected by the mass force
PublikacjaThe relations connecting perturbations specific for acoustic and entropy modes in an accelerated fluid or in a fluid affected by constant mass force, are derived. They allow to decompose the total vector of perturbations and the overall energy into acoustic and non-acoustic parts uniquely at any instant. In order to do this, three quantities are required, for example total perturbations in entropy, pressure and velocity. The evaluations...
-
Web component for automatic extraction of ontological information from informal description of web services
PublikacjaThis article treats about usage possibilities of Web Services and cooperation in development that leads to constant improvement of these components. It describes the semantic methods which can beused to create the description that is comprehensible for computers. It also presents the two models supporting the automatic generation of the semantic description based on informal description. Thepaper draws upon the comparison of two...
-
Who makes Europe
Publikacja"Obrzeża" seria obrazów Obrzeża to kompozycja złożona z obrazów akwarelowych, połączonych w poziomą linię o wysokości 10 cm, która narasta etapami, ciągle powiększając się. Jest to dość przewrotna opowieść o miejscach, bazująca na subiektywnej selekcji motywów przedstawionych za pomocą realistycznych odwzorowań zestawionych na zasadzie dyptyku z ich abstrakcyjnymi kontrapunktami.
-
On the synthesis of coupled-lossy resonator filters with unloaded quality factor control
PublikacjaA technique for fast synthesis of coupling matrix low-pass prototypes of generalized Chebyshev bandpass filters with lossy resonators is presented in this paper. The coupling matrix is found by solving a nonlinear least squares problem based on zeros and poles of filter's transfer functions. Additional constraints are introduced that allow one to control the level of unloaded quality factor of resonators.
-
A study of concentration depolarization and quenching of photoluminescence of solutions
PublikacjaThe concentration-dependence of emission anisotropy r/r0 and quantum yield eta/eta0 of the photoluminescence of glycerol-water solutions of rhodamine B in two systems of viscosities 7.4 P and 0.72 P is investigated. The experimental data are compared with the new theory of concentraticn depolarization (J. Lumin., 5, 413 (1972)) and concentration quenching of photoluminescence (Acta Phys. Hungar., 30, 145 (1972)), which takes...
-
Local and global response of sandwich beams made of GFRP facings and PET foam core in three point bending test
PublikacjaIn the paper behaviour of laminated sandwich beams (FRP face sheet – PET foam core – FRP face sheet) subjected to three point bending is studied. The paper aim is to find practical descriptions enabling effective and accurate estimation of the elastic response, damage and failure of the beams, basing on experiments and static calculations. Therefore a number of tests are described, that were done on laminated coupons and foam specimens...
-
A novel heterogeneous model of concrete for numerical modelling of ground penetrating radar
PublikacjaThe ground penetrating radar (GPR) method has increasingly been applied in the non-destructive testing of reinforced concrete structures. The most common approach to the modelling of radar waves is to consider concrete as a homogeneous material. This paper proposes a novel, heterogeneous, numerical model of concrete for exhaustive interpretation of GPR data. An algorithm for determining the substitute values of the material constants...
-
HYDROGEN PRODUCTION PERFORMANCE IN THERMOCATALYTIC REACTOR BASED ON THE INTERMETALLIC PHASE OF NI3AL
PublikacjaThe main aim of the following paper is mathematical modelling for momentum, heat and mass transfer, which is accompanied by chemical surface reactions of the flow of the mixture helium and methanol. The thermocatalytic devices used for decomposition of hydrocarbons incorporate vertical microchannels coupling at the ends and heated to 500 oC at the walls. The results of the experiment were compared with CFD calculations to calibrate...
-
Comparison of the exponential thermal transient parameterization methods with the SMTP method in the unipedicled DIEP flap computer modelling and simulation
PublikacjaThe aim of this paper is to compare the spatial contrast of the image descriptors obtained via three different thermal transient parameterization methods in Active Dynamic Thermography. The thermal constants and amplitude values of the one- and two- exponential parametrization are compared to the Simplified Magnitude-Temporal Parametrization method (SMTP). The comparison is performed using the data obtained by simulating the cold...
-
Influence of electrode geometric arrangement on the operation of narrow circular electrostatic precipitator
PublikacjaIn this work the influence of electrode geometric arrangement on the operation of a circular electrostatic precipitator (ESP) was investigated using Particle Image Velocimetry (PIV) method. The ESP was a glass circular cylinder (29 mm in diameter, 300 mm long) equipped with a wire discharge electrode and circular-cylinder collecting electrode. The stainless-steel discharge wire electrode (0.23 mm in diameter, 100 mm long) was mounted...
-
Determination of stepped plate thickness distribution using guided waves and compressed sensing approach
PublikacjaGuided waves recently have attracted significant interest as a very promising research area. The signals registered by a specially designed sensor network are processed to assess the state of the tested structure. Despite the constant development of novel damage detection algorithms employing guided waves, the phenomenon of wave propagation still needs detailed recognizing and understanding for the further progress of non-destructive...
-
Thermodynamic interpretation and prediction of CO2 solubility in imidazolium ionic liquids based on regular solution theory
PublikacjaRegular solution theory (RST) is the most popular model for the interpretation of the interaction between CO2 and ionic liquids. In the present work, the parameters of this model were determined for the CO2 absorption in eleven imidazolium ionic liquids. The y-intercept (A) of the RST model for the investigated imidazolium liquids increases with increasing temperature whereas the slope (B) remains constant. The values of RST parameters...
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublikacjaThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
Degradation of ferritic X10CrAlSi18 stainless steel caused by slurry
PublikacjaThe slurry erosion tests of ferritic X10CrAlSi18 steel were carried out using a slurry pot device. In order to investigate the erosion process, two series of tests were performed: first one with a constant impact velocity of 5 m/s, 7 m/s and 9 m/s and the second one, during which the impact velocity was changed after every exposure. During each test, an influence of test conditions on volume loss, surface hardness and roughness...
-
Theoretical and experimental analysis of guided wave propagation in plate-like structures with sinusoidal thickness variations
PublikacjaGuided waves have attracted significant attention for non-destructive testing (NDT) and structural health monitoring (SHM) due to their ability to travel relatively long distances without significant energy loss combined with their sensitivity to even small defects. Therefore, they are commonly used in damage detection and localization applications. The main idea of incorporating guided waves in NDT and SHM is based on processing...
-
Environmentally Friendly Fabrication of High-Efficient Fe-ZnO/Citric Acid-Modified Cellulose Composite and the Enhancement of Photocatalytic Activity in the Presence of H2O2
PublikacjaIn the present study, a novel Fe-ZnO/citric acid-modified cellulose composite (x%Fe-ZnOy% CAC) was synthesized using an environmentally friendly hydrothermal method. The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), UV−vis diffuse reflectance spectroscopy (DRS), Fourier transform infrared spectroscopy (FTIR), nitrogen physisorption, and electrochemical and photocurrent density...