Filtry
wszystkich: 3844
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: Influenza vaccines
-
Influence of statistical errors on damage detection based on structuralflexibility and mode shape curvature
PublikacjaDamage detection procedures based on measured natural frequencies and building structure mode shapes are discussed in this paper. Modal curvature and structural flexibility approaches are tested. Attention is paid to the modal identification errors that influence damage detection. This problem is studied using a computer simulation of a simple supported beam. For practical cases, the peak picking methodand its statistical errors...
-
Influence of accelerometer signal pre-processing and classification method on human activity recognition
PublikacjaA study of data pre-processing influence on accelerometer-based human activity recognition algorithms is presented. The frequency band used to filter-out the accelerometer signals and the number of accelerometers involved were considered in terms of their influence on the recognition accuracy. In the test four methods of classification were used: support vector machine, decision trees, neural network, k-nearest neighbor.
-
Influence of Gas-Flow Conditions on the Evolution of Thermally Insulating Si3N4 Nano-Felts
Publikacja -
The influence of UV-irradiation on the poly(vinyl alcohol)/hyaluronic acid film properties
Publikacja -
The Influence of Input Data Standardization Method on Prediction Accuracy of Artificial Neural Networks
Publikacja -
Influence of TiO2 hydrophilicity on the photocatalytic decomposition of gaseous acetaldehyde in a circulated flow reactor
Publikacja -
Influence of phonon-phonon coupling on superconducting state in honeycomb-type crystal lattice
Publikacja -
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublikacjaIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (),were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublikacjaIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (s), were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
Influence of Osmolytes on Protein and Water Structure: A Step To Understanding the Mechanism of Protein Stabilization
PublikacjaResults concerning the thermostability of hen egg white lysozyme in aqueous solutions with stabilizing osmolytes, trimethylamine-N-oxide (TMAO), glycine (Gly), and its N-methyl derivatives, N-methylglycine (NMG), N,N-dimethylglycine (DMG), and N,N,N-trimethylglycine (betaine, TMG), have been presented. The combination of spectroscopic (IR) and calorimetric (DSC) data allowed us to establish a link between osmolytes’ influence on...
-
Cough influence on fascia-mesh system built for a hernia repair - an experimental research
PublikacjaAn experimental approach to identify stronger and weaker fixation schemes in laparoscopic ventral hernia repair is presented in the paper. Two types of implants, whose mechanical properties are significantly different and five kinds of connectors are considered. Physical models of operated hernia have been built using those materials and porcine abdominal tissue. The models have been subjected to dynamic impulse load, similar to...
-
Influence of separation gap on the structural response of colliding structures under earthquake excitation
PublikacjaThe high level of urbanization in the XXIst century forces the designers to design closely-separated structures and to take into account many factors influencing their response during seismic excitation, which are the most unpredictable loads which can affect civil engineering structures. Interactions between insufficiently adjacent buildings, known as the earthquake-induced structural pounding, may cause serious damage to the structures,...
-
INFLUENCE OF TEMPERATURE ON THE ACTIVITY OF ANAMMOX GRANULAR BIOMASS - SHORT AND LONG-TERM ASPECT
PublikacjaThe aim of this study was to determine a short-term and long-term effect of temperature on the anammox process rate and determination of temperature coefficients in the Arrhenius and Ratkowski equations. The short-term effects of temperature on the anammox biomass were investigated in batch tests at ten different temperatures in the range of 10-55 ̊C. The maximum rate 1.3 gN (gVSS·d)-1 observed at 40 ̊C. The minimum rate, close...
-
Influence of water salinity on corrosion risk - the case of the southern Baltic Sea coast.
PublikacjaWater corrosivity in Gdansk Bay, Poland, the southern part of the Baltic Sea, was investigated. The analysed region is heavily industrialized, and the coastline is very diverse. Twenty-seven test points along the coastline were selected. Water parameters such as salinity, total dissolved solids content, resistivity, conductivity, oxygenation, pH and corrosion rate were determined. The results of the investigation are presented....
-
Influence of electric, magnetic and electromagnetic fields on the circadian system – current stage of knowledge
PublikacjaOne of the side effects of each electrical device work is the electromagnetic field generated near its workplace. All organisms, including humans, are exposed daily to the influence of different types of this field, characterized by various physical parameters. Therefore, it is important to accurately determine the effects of an electromagnetic field on the physiological and pathological processes occurring in cells, tissues and...
-
The influence of pre- and postharvest treatments on selected biological and epigenetic activities of Brassica sprouts
PublikacjaIntroduction The Brassica vegetables are rich in glucosinolates (GLs), which are enzymatically hydrolysed to bioactive isothiocynates (ITC) and indoles, regarded as the most promising chemopreventing agents. However, in the majority of brassica sprouts the GL conversion into these beneficial derivatives occurs at the level of about 1 %, while in cabbage leaves exceeds 70%. Since sprouts represent plant material, which is frequently...
-
The influence of precursor selection on electrochemical properties of radiofrequency thermal plasma synthesized graphene
Publikacja -
Electrochemical oxidation of sulphamerazine at boron-doped diamond electrodes: Influence of boron concentration
Publikacja -
INFLUENCE OF THE MARINE 4-STROKE DIESEL ENGINE MALFUNCTIONS ON THE NITRIC OXIDES EMISSION
Publikacja -
Influence of the rare-earth impurities on the Ga and Ge local structure in the Ca3Ga2Ge3O12 glass
PublikacjaW pracy przedstawione zostały wyniki analizy EXAFS realizowanejza pomocą metody GNXAS dla serii szkieł typu Ca3Ga2Ge3O12 domieszkowanych metalami ziem rzadkich (0.7 wt.% - Ce, Eu, Ho, Er; oraz 1.0 wt.% Nd). Badaniu poddano lokalne otoczenie wokół jonów Ge i Ga. Porównanie wyników z danymi strukturalnymi otrzymanymi dla szkła niedomieszkowanego wskazuje, że domieszka metali ziem rzadkich modyfikuje jedynie otoczenie jonów galu,...
-
Influence of composition of raw wastewater on removal of nitrogen compounds in multistage treatment wetlands
PublikacjaInfluence of composition of raw wastewater on the efficiency of organic matter and nitrogen removal in multistage treatment wetlands has been examined. Commonly used indicators, like COD/BOD5 and BOD5/TN ratio, determining wastewater susceptibility to biodegradation in conventional treatment technologies were assessed. It was confirmed that multistage treatment wetland may be used for treatment of wastewater with high loads of...
-
The influence of roasting and additional processing on the content of bioactive components in special purpose coffees
PublikacjaCoffee being the beverage consumed worldwide is also a very competitive commodity. Consequently, producers seek ways of attracting consumers by proposing e.g. novel ingredient combinations usually without evaluating their health quality. In this study, variations in health-promoting determinants for five special purpose coffee brews were characterized. The major bioactive components - chlorogenic acids (CAs) - detected by HPLC-DAD-MS...
-
The Influence of Selected Parameters of Numerical Modelling on Strains and Stresses at Weld Toe Notch
PublikacjaLatest development in the field of welding technology and prefabrication enabled massive production of thin-walled sandwich structures. Multi-layered sandwich structures are fabricated with the use of high-power CO2 lasers, friction welding, arc welding, hybrid welding, or other technique designed for the special purpose. Steel or aluminium alloy plates with thickness between 1 and 5 mm are connected by internal stiffeners. Strength...
-
An influence of the ship's block coefficient implementation on the evaluation of it's hull girder bending
PublikacjaAn influence of the three different ways of implementation ship's block coefficient δ (three geometrical models) on the stresses due to wave bending moment have been investigated. Two models have been applied and compared: beam one (description of the shape usingparameters) and FEM shell model (direct representation of the shape). The outcomes have been compared to Polish Register of Shipping (PRS) rules. The results show that...
-
Influence of the glycolysis agent on the structure of the glycolysates obtained from polyether-urethane wastes
PublikacjaW pracy zaprezentowano wybrane wyniki badań wpływu środków glikolizujących na strukturę glikolizatów otrzymywanych w procesie glikolizy odpadowych pianek polietero-uretanowych.
-
The influence of selenium addition during seeds' germination on the biological properties of obtained sprouts
PublikacjaSelenium plays a vital role in human body, because in the form of aminoacids (Se-methionine, Se-cysteine) it is found in the active centres of over 25 enzymes, including those regarded as 'cytoprotective'. Unfortunatelly, its daily intake in Poland and other European countries is lower than predicted by dietary recommendations. The consequences of selenium deficiency in diet might be severe, including higher susceptibility to cardio-vascular...
-
Influence of spatial structures of 316L stainless steel on its cavitation erosion resistance
Publikacja -
The influence of temperature on properties of the polymer flexible joint used for strengthening historical masonries
PublikacjaA new method of repairing damaged structures by filling the cracks with a specially prepared elastomeric polymer mass has been recently proposed. This new and innovative technique, known as the Flexible Joint Method (FJM), is mainly dedicated to masonries and historical objects, where minimum intervention is permitted. The flexible joint bonds the disrupted elements and ensures further safe exploitation of a damaged structure....
-
The influence of the substrate temperature on the preparation of DNA films for studies under vacuum conditions
PublikacjaPrzeanalizowano wpływ temperatury na formowanie warstw DNA. Sprawdzono wpływ stabilizatorów na jakość otrzymanych próbek. Stwierdzono, że optymalnymi warunkami przygotowywania filmów do badań w warunkach próżniowych jest - 10 st. C przy minimalnej zawartości NaOH.
-
Allergic Reactions as a Defense of the Organism to the Influence of Implants Components Made of Stainless Steel
PublikacjaDue to the increasing number of cases of hypersensitivity caused by direct contact with metals, as well as the increasing demand for implants in humans all ages numerous studies on the effects of the impact of implant components are being carried out. The paper presents the phenomenon of etiology of allergy in general terms and in relation to the biomaterials used in medicine. There have been characterized in terms of impact on...
-
Oxidation Time Influence on the Structure of the Cobalt Base Clad Layer and Scale Morphology
PublikacjaZbadano wpływ czasu utleniania na mikrosrukutręi własności mechaniczne a w szczególności mikrotwardość, warstw wykonanych ze stopu kobaltu.Warstwy były wykonane za pomocą napawania plazmowego (PTA). Stop kobaltu podlegał utlenianiu w powietrzu w temperaturze 800 topni celsjusza w czasie 1, 22 i 200 godzin. w wyniku utleniania nastapiło uformowanie warstw zgorzeliny oraz nastapiły zmiany w mikrostrukturze. Zaobserwowano także zmiany...
-
Allergic reactions as a defense of the organism to the influence of implants components made of stainless steel
PublikacjaDue to the increasing number of cases of hypersensitivity caused by direct contact with metals, as well as the increasing demand for implants in humans all ages numerous studies on the effects of the impact of implant components are being carried out. The paper presents the phenomenon of etiology of allergy in general terms and in relation to the biomaterials used in medicine. There have been characterized in terms of impact on...
-
Influence of pore formers on electrical properties of CaTi0.9Fe0.1O3-δ perovskite-type ceramics
PublikacjaPorous CaTi0.9Fe0.1O3-δ (CTF) perovskites were synthesized by the standard solid state method at different sintering temperatures with carbon black (CB), corn starch (CS) and potato starch (PS) as pore-forming agents. The ceramic samples of porosity between 9% and 42% with 5 - 40 μm pore sizes, were obtained by a 6 h sintering at either 1130º C or 1200º C of precursor powder prepared at 1470º C. X-ray diffraction analysis proved...
-
The influence of accumulation area and the length of pedestrian route on functioning of roundabouts with traffic signals
Publikacjatraffic volumes. This kind of intersection is commonly used in the centres of Polish cities on multilane roads and fairly common in the case of tram lines running through a central island. The increase of traffic flow volumes on left turn and U-turn has made this type of roundabout difficult to operate. Small storage areas around central islands are critical places that significantly influence the capacity of this kind of intersection....
-
Influence of Spatial Structures of 316L Stainless Steel on Its Cavitation Erosion Resistance
PublikacjaCavitation erosion performance of modified macroscopic internal structure 316L stainless steel was investigated. The samples processed by means of SLM method were subjected to cavitation erosion test. The scanning electron microscope Philips 30/ESEM was used to examine morphology of eroded surface.
-
Influence of water and mineral oil on the leaks in satellite motor commutation unit clearances
PublikacjaThe article describes the flow rates of mineral oil and water flowing, as working media, through the commutation unit of a hydraulic satellite motor. It is demonstrated that geometrical dimensions of commutation unit clearances change as a function of the machine shaft rotation angle. Methods for measuring the rate of this flow and the pressure in the working chamber are presented. The results of pressure measurements in the working...
-
Geometry optimization of steroid sulfatase inhibitors - the influence on the free binding energy with STS
PublikacjaIn the paper we review the application of two techniques (molecular mechanics and quantum mechanics) to study the influence of geometry optimization of the steroid sulfatase inhibitors on the values of descriptors coded their chemical structure and their free binding energy with the STS protein. We selected 22 STS-inhibitors and compared their structures optimized with MM+, PM7 and DFT B3LYP/6–31++G* approaches considering separately...
-
Influence of yttria surface modification on high temperature corrosion of porous Ni22Cr alloy
PublikacjaProtective coatings for porous alloys for high temperature use are relatively new materials. Their main drawback is high temperature corrosion. In this work protective coatings based the on Y-precursor infiltrated into the sintered Ni22Cr alloys are studied at 700°C. Effects of the amount of the protective phase on the resulting corrosion properties are evaluated in air and humidified hydrogen. Weight gain of the samples, their...
-
Influence of bitumen type on cracking resistance of asphalt mixtures used in pavement overlays
PublikacjaCracking is one of the predominant distresses occurring in flexible pavements, especially in old pavements that were rehabilitated with an asphalt overlay. In such cases asphalt mixtures should be designed to ensure high resistance to reflective cracking because new asphalt layers are exposed to existing cracks of the old pavement. The nature of these cracks can be various (transverse, longitudinal as well as crazy cracking). One...
-
The influence of microjet array area ratio on heat transfer in the compact heat exchanger
PublikacjaThe paper describes the comprehensive study on the effect of microjet array geometrical parameters on the heat transfer enhancement in the modular heat exchanger. The conducted experimental study provides an experimental database on single phase submerged microjet heat transfer. The Wilson plot method was applied to determine the heat transfer coefficients in the laminar and transition flow regimes of a liquid-to-liquid heat exchanger....
-
The influence of the development of private air communication on the architecture and urban planning of the 21st century
PublikacjaIn the first part, the article describes the stages of the development of gyroplanes and the influence of wartime policy on the interest in light aircraft. Also presented are links and the possibilities of using gyroplanes in various sectors of the economy. The authors, based on source texts, present the current position of the aviation industry in the Polish economy and attempt to diagnose its development capabilities. As a result,...
-
THE INFLUENCE OF THE URBAN DESIGN ON THE AIR EXCHANGE IN CITIES. SELECTED PROBLEMS IN POLISH REALITY
PublikacjaThe progress of the architecture and urbanism raises problems requiring interdisciplinary research conducted with the use of advanced experimental techniques and computer simulation. The fields of this research include aerodynamics, especially in intensively developed area of Environmental Wind Engineering (EWE). Aerodynamic phenomena occurring around buildings have a significant impact on the quality of the climate in the cities....
-
Influence of sodium dodecyl sulfate presence on esterification of propylene glycol with lauric acid
PublikacjaZbadano wpływ obecności dodecylosiarczanu sodu na bezpośrednią estryfikację glikolu propylenowego kwasem laurynowym. Zbadano także rozkład wielkości cząstek mikroemulsji tworzącej się in situ w trakcie estryfikacji glikolu propylenowego kwasem laurynowym w obecności różnych stężeń dodecylosiarczanu. Oceniono wartość równowagi hydrofilowo - lipofilowej zsyntetyzowanych emulgatorów.
-
Influence of pressure on heat transfer during pool boiling on smooth tube bundle
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia wody, metanolu i R141b na pęu rur głądkich w warunkach podcisnienia i ciśnienia atmosferycznego
-
Influence of geometric imperfections on capacities of silo structures loaded with pressure below atmospheric
PublikacjaPrzedstawiono probabilistyczną analizę nośności aluminiowego silosu ze wstępnymi imperfekcjami geometrycznymi obciążonego podciśnieniem. Imperfekcje opisano za pomocą dyskretnych odchyłek przyjętych zgodnie z maksymalnymi niedokładnościami dopuszczonymi przez normy. Ponadto wygenerowano imperfekcje płaszcza silosu, stosując jednorodne i niejednorodne pola losowe. Wykonano numeryczne obliczenia geometrycznie i materiałowo nieliniowe.
-
Numerical Analysis of Magnetic Core Properties Influence on Residual Current Device Behaviour
PublikacjaW artykule przedstawiono analizę wpływu kształtu prądu w uzwojeniu pierwotnym transformatora prądowego na pracę przekładnika różnicowo-prądowego. Przeprowadzono obliczenia symulacyjne dla wymuszenia o kształcie sinusoidy i sinusoidy wyprostowanej dla częstotliwości 50 Hz. Wzięto pod uwagę dwa typy charakterystyki magnesowania transformatora: dla materiału magnetycznie miękkiego i materiału o prostokątnej pętli histerezy. Analiza...
-
Interactions of dissolved dsDNA with intercalating drug by anodic voltammetry and spectroscopy. Influence of pH
PublikacjaOddziaływanie związku przeciwnowotworowego C-1305 z DNA było badane przy pomocy impulsowej voltametrii różnicowej oraz spektroskopii UV/Vis. Triazoloakrydon C-1305 oddziałuje z DNA na dwóch drogach: przez interkalacje pomiedzy pary zasad oraz przez wiązanie sie w małym rowku helisy. W fizjologicznym pH (7,4) stałe wiązania wynoszą: K1=3,36E+5 i K2=0,18E+5 [1/M] a wielkość miejsca wiązania: n1=2,5 i n2=4,0, odpowiednio dla pierwszego...
-
The influence of small amount of substances present in tissue on the optical spectrum of immunosuppressive drug
PublikacjaIn this paper, we describe how commonly present in tissue substances - sodium chloride and glucose - affect the optical spectrum of an immunosuppressive drug (Cyclaid® by Apotex). Prepared samples were investigated using the spectrophotometer in the spectrum range from 250 nm to 1100 nm. The maximum wavelength shift calculated on the basis of measurement results is not bigger than the measurement wavelength step. So, it can be...
-
Influence of geotechnical conditions on damage states of Gdansk Bay Coast cliff formations
PublikacjaA geotechnical aspect of destruction processes of seashores was identified based on the case of erosion of Gdansk Bay Coast cliff formations. Causative factors of landslide were described in the context of natural phenomena, land development and its anthropogenic transformations. Possible directions of theoretical analysis of changes in groundwater relations were indicated.
-
An in-depth look at the tire rubber hardness influence on tire/road noise measurements
PublikacjaWhen assessing the acoustic quality of a road pavement with the close-proximity (CPX) or the on-board sound intensity (OBSI) method, the rubber hardness of the reference tire substantially affects the measurement. Practical experience shows that measurement tires can get significantly harder within a single measurement season. This is why one would like to normalize measurements to a reference rubber hardness. The recently published...