Filtry
wszystkich: 1020
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: SZEWALSKI CYCLE
-
Dynamic characteristics of the proton exchange membrane fuel cell module
PublikacjaThe paper describes a fuel cell based system and its performance. The system is based on two fuel cell units, DC/DC converter, DC/AC inverter, microprocessor control unit, load unit, bottled hydrogen supply system and a set of measurement instruments. In the study presented in the paper a dynamic response of the proton exchange membrane (PEM) fuel cell system to unit step change load as well as to periodical load changing cycles...
-
The Magnetic Fluid Seals Research Results vs. Kelvin-Helmholtz (K-H) instability and Preliminary Conclusions
PublikacjaIn the article a magnetic-fluid seals durability research and the tests results are presented. The tests were made with three magnetic fluids using various magnets quantity in magnetic assemblies. If values obtained in the repeated test deviated by more than 10 % from results of the first test an additional control test was made for final characteristics. The characteristics are: critical pressure, critical motion velocity and...
-
Photocatalytic activity of nitrogen doped TiO2 nanotubes prepared by anodic oxidation: The effect of applied voltage, anodization time and amount of nitrogen dopant
PublikacjaNitrogen doped TiO2 nanotube arrays were prepared by anodizing Ti foils in an organic electrolyte containing specified amounts of urea as nitrogen precursor. The photocatalytic activity of the samples was evaluated by analyzing the degradation kinetics of phenol in water. The influence of tubes’ length, tubes’ surface morphology and amount of nitrogen in the TiO2 lattice on hydroxyl radical formation efficiency, photocatalytic...
-
Low temperature processed MnCo2O4 and MnCo1.8Fe0.2O4 as effective protective coatings for solid oxide fuel cell interconnects at 750 °C
PublikacjaIn this study two materials, MnCo2O4 and MnCo1.8Fe0.2O4 are studied as potential protective coatings for Solid Oxide Fuel Cell interconnects working at 750 °C. First powder fabrication by a modified Pechini method is described followed by a description of the coating procedure. The protective action of the coating applied on Crofer 22 APU is evaluated by following the area specific resistance (ASR) of the scale/coating for 5500...
-
Application of microturbines in CHP systems with reciprocating engines
PublikacjaThe analysis was carried out for Combined Heat and Power generation systems with micro-turbines power plants working on heat rejected from the reciprocating engine. The calculations were performed for GE Jerbacher engines of J320 GS- C05, J320 GS- C25 and J416 GS- B05 types. We considered different working media (both wet and dry fluids): water, ammonia, ethanol, methanol, methylacetylene (propyne), dimethyloether, sulphur dioxide,...
-
Application of Barycentric Coordinates in Space Vector PWM Computations
PublikacjaThis paper proposes the use of barycentric coordinates in the development and implementationof space-vector pulse-width modulation (SVPWM) methods, especially for inverters with deformed space-vector diagrams. The proposed approach is capable of explicit calculation of vector duty cycles, independentof whether they assume ideal positions or are displaced due to the DC-link voltage imbalance. The use ofbarycentric coordinates also...
-
Electrochemical behavior of a composite material containing 3D-structured diatom biosilica
Publikacja3D-structured diatom biosilica mixed with conducting carbon black was investigated as an active electrode material for lithium-ion batteries. Diatom biosilica was obtained by cultivation of the selected diatom species under laboratory conditions. Several instrumental techniques (XRD, FTIR, Raman, SEM-EDX, TGA) were used to characterize the physicochemical properties of applied biosilica. It was evidenced that the prepared new composite...
-
Nano Tin/Tin Oxide Attached onto Graphene Oxide Skeleton as a Fluorine Free Anode Material for Lithium-Ion Batteries
PublikacjaHerein, we show a composite formation method of tin/tin oxide nanoparticles with graphene oxide and CMC based on laser ablation technique as an electrode material for energy storage devices. The material exhibited a three-dimensional conducting graphene oxide network decorated with tin or tin oxide nanoparticles. The structure, homogeneous distribution of nanoparticles, and direct contact between inorganic and organic parts were...
-
Scaled agile framework. Dealing with software process‐related challenges of a financial group with the action research approach
PublikacjaThis article reports on a domain-specific software development venture at Nordea. We explore organizational constraints, challenges, and corrective actions undertaken when scaling the agile development approach of their Core Banking Platform program. The fit and required customizations of the rather complex and rigid SAFe framework in a policy-heavy financial institution are audited against the organic growth of the program. In...
-
Fatigue life improvement using low transformation temperature weld material with measurement of residual stress
PublikacjaWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Highly sensitive large strain cellulose/multiwalled carbon nanotubes (MWCNTs)/thermoplastic polyurethane (TPU) nanocomposite foams: From design to performance evaluation
PublikacjaAerogel-based polymer composite foams are promising for large strain piezoresistive sensors, but their aerogel skeleton is partially destroyed during the foaming process, limiting their sensitivity. Herein, the thermoplastic polyurethane was synthesized on the aerogel skeleton to obtain cellulose/multiwalled carbon nanotubes (MWCNTs)/thermoplastic polyurethane (TPU) nanocomposite materials foamed with the aid of supercritical carbon...
-
Selected design and construction aspects of supercritical steam generators for high temperature reactors = Wybrane aspekty konstrukcyjne i projektowe generatorów pary nadkrytycznej ogrzewanych z reaktorów wysokotemperaturowych
PublikacjaW artykule zaprezentowano uwarunkowania projektowe i konstrukcyjne nadkrytycznego generatora pary (jednoprzepływowego) wykorzystującego do ogrzewania hel z reaktorów HTR i VHTR. Wymiennik helikoidalny jest preferowany dla zwiększenia wymiany ciepła i zwartości. Badano własności czynników wymieniających ciepło z parą w obszarach przy- i nadkrytycznych. Analizowano korelacje, aby wybrać najbardziej wiarygodne. Przedyskutowano najbardziej...
-
Anticancer Imidazoacridinone C-1311 is Effective in Androgen-Dependent and Androgen-Independent Prostate Cancer Cells
PublikacjaAndrogen receptor (AR) plays a crutial role in prostate cancer (PCa) development and metastasis. Here, we reported potent anti-PCa activity of a small molecule imidazoacridinone C-1311. In AR-positive PCa cells, C-1311 was found to inhibit the transcriptional activity of AR uncovering a novel mechanism that may be relevant for its anticancer effect. Mechanistically, C-1311 decreased AR binding to prostate-specific antigen (PSA)...
-
Improved cytotoxicity and preserved level of cell death induced in colon cancer cells by doxorubicin after its conjugation with iron-oxide magnetic nanoparticles
PublikacjaA promising strategy for overcoming the problem of limited efficacy in antitumor drug delivery and in drug release is the use of a nanoparticle-conjugated drug. Doxorubicin (Dox) anticancer chemotherapeutics has been widely studied in this respect, because of severe cardiotoxic side effects. Here, we investigated the cytotoxic effects, the uptake process, the changes in cell cycle progression and the cell death processes in the...
-
Management of low-temperature heat source by ORC aided by additional heat source
PublikacjaThe presented work is aimed at utilisation of waste heat in the manner to produce electricity in ORC installation. Therefore the precondition of the study was to use the waste heat available in the form of a stream of hot water at 90°C. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. That was the incentive to search for the ways of increasing the temperature of the...
-
Nitrogen transformations and mass balances in anaerobic/anoxic/aerobic batch experiments with full-scale biomasses from BNR activated sludge systems.
PublikacjaThe aim of this study was to investigate nitrogen mass balances occurring inside full-scale BNR activated sludge systems, with special attention to colloidal and dissolved organic nitrogen (CON and DON) transformations. For this purpose, laboratory experiments were carried out using process biomass from two large BNR plants in northern Poland. Two parallel batch reactors were operated in a 3-phase (anaerobic/anoxic/aerobic) cycle....
-
Nitrogen transformations and mass balances in anaerobic/anoxic/aerobic batch experiments with full-scale biomasses from BNR activated sludge systems.
PublikacjaThe aim of this study was to investigate nitrogen mass balances occurring inside full-scale BNR activated sludge systems, with special attention to colloidal and dissolved organic nitrogen (CON and DON) transformations. For this purpose, laboratory experiments were carried out using process biomass from two large BNR plants in northern Poland. Two parallel batch reactors were operated in a 3-phase (anaerobic/anoxic/aerobic) cycle....
-
The reduction of auxiliaries power demand: The challenge for electromobility in public transportation
PublikacjaAn important role in the consumption of electric energy in urban transport are non-traction needs (auxiliaries), the main part of which is heating and air condition (HVAC). Auxiliaries are responsible for almost half of total energy consumption (normal weather conditions) and in the winter (or hot summer) it reaches up to 70% in daily scale. The reduction of energy used for non-traction needs is currently the main challenge related...
-
Fabrication of Durable Ordered Ta2O5 Nanotube Arrays Decorated with Bi2S3 Quantum Dots
PublikacjaOne of the most important challenges in the fabrication of ordered tantalum pentaoxide (Ta2O5) nanotube arrays (NTs) via the electrochemical method is the formation of nanotubes that adhere well to the Ta substrate. In this paper, we propose a new protocol that allows tight-fitting Ta2O5 nanotubes to be obtained through the anodic oxidation of tantalum foil. Moreover, to enhance their activity in the photocatalytic reaction, in...
-
Interactions of telomeric proteins with nucleic acids: sequence recognition on intact and oxidatively damaged telomeres
PublikacjaTelomeres are complex nucleoprotein assemblies that play a vital role in the maintenance of functional ends of linear chromosomes. Telomeric DNA, composed of tandem repeats of the 5'-TTAGGG-3' motif, solves the so-called end replication problem: as chromosomes shorten with each cell division, no information is lost, and the telomere can be re-extended. In the cell, many protein factors regulate telomere length, nuclear positioning...
-
Design and computational fluid dynamics analysis of the last stage of innovative gas-steam turbine
PublikacjaResearch regarding blade design and analysis of flow has been attracting interest for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics and computational flow mechanics. Currently a combination of mentioned methods is used for the design of turbine blades. These methods enabled us to improve flow efficiency...
-
Modyfikacja cementu kostnego w celu uzyskania długotrwałej ochrony antybakteryjnej
PublikacjaNiniejsza rozprawa doktorska stanowi przewodnik po jednotematycznym cyklu publikacji, dotyczącym modyfikacji akrylowego cementu kostnego celem uzyskania długotrwałej i efektywnej ochrony antybakteryjnej. W ramach niego przeprowadzono badania eksperymentalne polegające na opracowaniu technologii wytwarzania modyfikowanego cementu kostnego oraz procedury medycznej jego stosowania. Cement kostny był modyfikowany przez zastosowanie...
-
Wavelet transform analysis to assess oscillations in pial artery pulsation at the human cardiac frequency
PublikacjaPial artery adjustments to changes in blood pressure (BP)may last only seconds in humans. Using a novelmethod called near-infrared transillumination backscattering sounding (NIR-T/BSS) that allows for the non-invasive measurement of pial artery pulsation (cc-TQ) in humans, we aimed to assess the relationship between spontaneous oscillations in BP and cc-TQ at frequencies between 0.5 Hz and 5 Hz. We hypothesized that analysis of...
-
The topography of strontium–borate glasses and glass-ceramics containing bismuth and vanadium oxides measured with SEM method
Dane BadawczeThe topography of strontium–borate glasses and glass-ceramics containing bismuth and vanadium oxides was measured by SEM.
-
Development of banking sectors in Kosovo and Montenegro in the years 2000 - 2010
PublikacjaThe article presents main aspects of development of banking markets in two Balkan countries - Kosovo and Montenegro. Both of them are charaterised by similar recent history, both in political and economical fields. Their financial sectors have had to be built almost from scretch. The author describes stages of development of competition in the banking sectors, using the following ratios: performace, structure, liquidity. The data...
-
Understanding the capacitance of thin composite films based on conducting polymer and carbon nanostructures in aqueous electrolytes
PublikacjaIn this work electrochemical performance of thin composite films consisted of poly(3,4-ethylenedioxythiophene) (PEDOT), graphene oxide (GOx) and oxidized multiwalled carbon nanotubes (oxMWCNTs) is investigated in various sulphates (Li2SO4, Na2SO4, K2SO4, MgSO4) and acidic (H2SO4) electrolytes. Capacitance values, rate capability and cycling stability achieved for the composite layers are correlated with the electrolytes’ properties...
-
Multi-stage magnetic-fluid seals for operating in water - life test procedure, test stand and research results. Part II Results of life tests of multi-stage magnetic - fluid seal operating in water
PublikacjaThe edge criteria for magnetic-fluid seals durability research were described in previous article [24] and now the tests results are presented. The tests were made with three magnetic fluids using various magnets quantity in magnetic assemblies. If values obtained in the repeated test deviated by more than 10 % from results of the first test an additional control test was made for final characteristics. The characteristics are:...
-
Ag/Pt-modified TiO2 nanoparticles for toluene photooxidation in the gas phase
PublikacjaAg/Pt-modified TiO2nanocomposites were synthesized using the sol–gel method. The effect of metal typeand amount as well as synthesis route on the photocatalytic activity in reaction of toluene removal, usedas a model volatile organic compound, was investigated. Toluene, at the concentration of about 200 ppm,was irradiated over modified TiO2using light-emitting diodes (LEDs, max= 415 nm). The results showedthat toluene could be...
-
99mTc-Galacto-RGD2: A Novel 99mTc-Labeled Cyclic RGD Peptide Dimer Useful for Tumor Imaging
PublikacjaThis study sought to evaluate [99mTc(HYNIC-Galacto-RGD2)-(tricine)(TPPTS)] (99mTc-Galacto-RGD2: HYNIC = 6-hydrazinonicotinyl; Galacto-RGD2 = Glu[cyclo[Arg-Gly-Asp-D-Phe-Lys(SAA-PEG2-(1,2,3-triazole)-1-yl-4-ethylamide)]]2 (SAA = 7-amino-L-glycero-L-galacto-2,6-anhydro-7-eoxyheptanamide, and PEG2 = 3,6-dioxaoctanoic acid); and TPPTS = trisodium triphenylphosphine-3,3',3''-trisulfonate) as a new radiotracer for tumor imaging. Galacto-RGD2...
-
Preparation and X-ray structures of selected aminium thiosulfates
PublikacjaVarious types of aminium thiosulfates (1–6), including hydrates and mixed salts, have been obtained by the reaction of ammonium thiosulfate with amines. Tertbutylamine, cyclo-hexylamine and 1,6-diaminohexane gave crystals of (t-BuNH3)2S2O3·H2O (1), (c-C6H11NH3)2S2O3 (3) and {(NH4)2(H3NC6H12NH3)(S2O3)2} (6), respectively, which were investigated by X-ray structural analysis. Extensive hydrogen bonding of the N-H…O and N-H…S type...
-
Rtęć w rozwoju osobniczym kormorana czarnego i jej biomagnifikacja w odniesieniu do ryb w ekosystemie Zalewu Wiślanego = Mercury in the individual development of Great Cormorants and its biomagnification in relation birds- fish in the Vistula Lagoon
PublikacjaRtęć jest pierwiastkiem, który wykazuje zdolność do kumulacji w glebie, roślinach i organizmach zwierzęcych. Jej związki charakteryzują się zróżnicowanymi właściwościami chemicznymi i fizycznymi, włączane są w różnego rodzaju cykle przyrodnicze. Bardzo szkodliwe sa pary rtęci dostające się do organizmów poprzez drogi oddechowe. Substancje toksyczne mogą zostać również wchłonięte wraz z treścią pokarmową i poprzez krew rozprowadzane...
-
The effect of multiaxial geocomposite reinforcement on fatigue performance and crack propagation delay in double-layered asphalt beams
PublikacjaThe presented study investigates the effect of a recently developed multiaxial geocomposite made of polypropylene geogrid and non-woven fabric on the delay of crack propagation, based on four-point bending tests of large asphalt concrete beams – both for reinforced and non-reinforced specimens. Several approaches are described in this study, including analysis of stiffness modulus decrease and analysis of crack propagation using...
-
Effect of austempering temperature on microstructure and cyclic deformation behaviour of multiphase low-carbon steel
PublikacjaThis paper examined the cyclic deformation behaviour of multiphase low-carbon steel that was subjected to austempering heat treatments at four temperatures (190 °C, 230 °C, 275 °C, and 315 °C) below the martensite start temperature (Ms = 353 °C). The tests were conducted at room temperature, under fully reversed strain-controlled conditions, with strain amplitudes in the range 0.5–1.0%. The microstructure was observed by transmission...
-
Strain sequence effect on fatigue life and fracture surface topography of 7075-T651 aluminium alloy
PublikacjaThe paper studies the effect of strain-loading sequence on fatigue lifetime and fracture surface topographies in 7075-T651 aluminum alloy specimens. Fatigue tests were performed in two ways: (i) constant-amplitude loading and (ii) two series of variable amplitude loading with non-zero mean strain values. The topography of the fatigue fractures was measured over their entire surfaces with the help of an optical confocal measurement...
-
A dual-control strategy based on electrode material and electrolyte optimization to construct an asymmetric supercapacitor with high energy density
PublikacjaMetal-organic frames (MOFs) are regarded as excellent candidates for supercapacitors that have attracted much attention because of their diversity, adjustability and porosity. However, both poor structural stability in aqueous alkaline electrolytes and the low electrical conductivity of MOF materials constrain their practical implementation in supercapacitors. In this study, bimetallic CoNi-MOF were synthesized to enhance the electrical...
-
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
PublikacjaThis work aims to compare the mechanical behavior of an AISI H13 steel obtained by additive manufacturing with that obtained by conventional manufacturing methods. The average values of the ultimate tensile strength (UTS) and ductility obtained for the specimens produced by the conventional method were equal to 658 MPa and 18%, respectively, which compares with 503 MPa and 0.75% registered for the selective laser melting (SLM)...
-
Relationship between GIX, SIDX, and ROTI ionospheric indices and GNSS precise positioning results under geomagnetic storms
PublikacjaIonospheric indices give information about ionospheric perturbations, which may cause absorption, diffraction, refraction, and scattering of radio signals, including those from global navigation satellite systems (GNSS). Therefore, there may be a relationship between index values and GNSS positioning results. A thorough understanding of ionospheric indices and their relationship to positioning results can help monitor and forecast...
-
STUDY ON THE RELATIONSHIP BETWEEN VEHICLE MAINTENANCE AND FUEL CONSUMPTION
PublikacjaA contemporary road vehicle (RV) is a rather complex system, consisting of a large number of subsystems, assemblies, units, and elements (parts). While operating, an RV interacts with the environment, and its elements interact with each other. Consequently, the properties (parameters) of these elements change in the process - hardness, roughness, size, relative position, gapping, etc. A partial solution to the presented problems...
-
Tools for road infrastructure safety management in Poland
PublikacjaThe objective of road safety infrastructure management is to ensure that when roads are planned, designed, built and used road risks can be systematically identified, assessed, removed and mitigated. There are a number of approaches to road safety management. European Union Directive 2008/96/EC requires EU member states to use four basic tools of road safety infrastructure management. An overview of the methods in these countries...
-
Decision support system for design of long distance heat transportation system
PublikacjaDistrict Heating (DH) systems are commonly supplied using local heat sources. Nowadays, modern insulation materials allow for effective and economically viable heat transportation over long distances (over 20 km). The paper proposes a Decision Support System (DSS) for optimized selection of design and operating parameters of a long distance Heat Transportation System (HTS). The method allows for evaluation of feasibility and effectiveness...
-
Smart Virtual Product Development (SVPD) System to Support Product Inspection Planning in Industry 4.0
PublikacjaThis paper presents the idea of supporting product inspection planning process during the early stages of product life cycle for the experts working on product development. Aim of this research is to assist a collaborative product development process by using Smart Virtual Product Development (SVPD) system, which is based on Set of Experience Knowledge Structure (SOEKS) and Decisional DNA (DDNA). The proposed system is developed...
-
Optimization of the Aeration Strategies in a Deammonification Sequencing Batch Reactor for Efficient Nitrogen Removal and Mitigation of N2O Production
PublikacjaIn deammonification systems, nitrite-oxidizing bacteria (NOB) suppression and nitrous oxide (N2O) mitigation are two important operational objectives. To carry out this multivariable analysis of response, a comprehensive model for the N cycle was developed and evaluated against experimental data from a laboratory-scale deammonification granular sludge sequencing batch reactor. Different aeration strategies were tested, and the manipulated...
-
Aquaponics Based Artificial Biosphere Included in Architecture: From Mitigation of Negative Impacts to Positive Added Values of Urban Spatial Structures on Local, Regional and Global Scale
PublikacjaTechnologies may appear faster than spatial planning can afford it. Alt hough applying new technologies solve particular problems, it may also create new ones. Many negative consequences of implementing new technologies are visible a fter years or decades – they accumulate until the need of solving them. According to The Hannover Principles (McDonough & Braungart 2013) one should, by example not think about...
-
Technical and economic conditions of supplying residential consumers with heat from nuclear power plant
PublikacjaThe reduction of CO2 emission requires technological shift towards carbon-free options. Cogeneration of electricity and heat based on coal and natural gas will experience generation cost increase, if the costs of emissions are imposed on the plant operators. Therefore, nuclear and renewable options should be considered. In this paper, we present the concept of electricity and heat supply system with nuclear condensing turbine adapted...
-
Thermodynamic and economic analysis of nuclear power unit operating in partial cogeneration mode to produce electricity and district heat
PublikacjaThis paper presents the methodology of techno-economic analysis for a nuclear unit operating in partial cogeneration mode and its application for the case study: a nuclear power plant planned in Poland. The research objectives were: to propose EPR, AP1000 and ESBWR nuclear condensing-extraction turbine systems modifications required for operation in cogeneration, to determine optimal heat production and heat transport line (HTL)...
-
The impact of sediment, fresh and marine water on the concentration of chemical elements in water of the ice-covered lagoon
PublikacjaThe common use of chemical elements by man has been contributing to their extraction for centuries. As a consequence, they have been directly or indirectly introduced into the biogeochemical cycle. In the framework of many conventions, mining and processing of elements are currently subject to many restrictions. However, their large load that has already been deposited in the soil and bottom sediments can be remobilised and...
-
Expression of cyclin D1 after treatment with doxorubicin in the HL-60 cell line
PublikacjaIncreased levels of cyclin D1 and amplification of CCND1 gene occur in many types of cancers. We have followed the expression of cyclin D1 after treatment with doxorubicin with reference to cell death and other possible therapeutic implications. The effect of the treatment on the cell cycle, survival, intracellular level (flow cytometry), and intracellular localization of cyclin D1 (fluorescence microscopy) and expression of...
-
The newest researches and applications of treatment wetlands in sewage sludge management
PublikacjaIn the paper the newest researches and applications of treatment wetlands conducted by re-searchers of Civil and Environmental Faculty are presented. Among others it was proved that this technology could be successfully implemented for highly polluted wastewater treatment. Within the research project two multistage treatment wetlands, one for landfill leachate and the second for reject water from digested sewage sludge centrifugation,...
-
The early failure of the gamma nail and the dynamic hip screw in femurs with a wide medullary canal. A biomechanical study of intertrochanteric fractures
PublikacjaBackground: Intertrochanteric fractures may occur in a bone with a wide medullary canal that may lead to significant mobility of a intramedullary nail, contrary to an extramedullary device. This study evaluates the Dynamic Hip Screw and the gamma nail in AO 31.A2.1 fractures in these circumstances. Methods: Synthetic femora with canals drilled to 18 mm were used. Five fixation types were examined: a 2 - hole and a 4 – hole Dynamic...
-
ENERGY ANALYSIS OF THE PROPULSION SHAFT FATIGUE PROCESS IN A ROTATING MECHANICAL SYSTEM PART II IDENTIFICATION STUDIES – DEVELOPING THE FATIGUE DURABILITY MODEL OF A DRIVE SHAFT
PublikacjaThe article presents a continuation of research carried out concerning identification of energy consequences of mechanical fatigue within a propeller shaft in a rotating mechanical system, while working under conditions of the loss of the required alignment of shaft lines. Experimental research was carried out on a physical model reflecting a full-sized real object: i.e., the propulsion system of the ship. It is proven, by means...