Wyszukiwarka
Filtry
wszystkich: 1145
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: platwie dachowe
-
Heat transfer intensification by enlarged surface roughness in the plate heat exchanger
PublikacjaIn the paper an experimental analysis of passive heat transfer intensification technique employed in the case of the plate heat exchanger is presented. The passive intensification was obtained by a modification of the heat transfer surface. The roughness of surface was increased by a use of glass micro-beads. Single-phase convective heat transfer in the water-water system was studied. The experiment was accomplished in two stages....
-
The Influence of Workpiece Hardness on Plate Temperature during One Side Lapping
PublikacjaLapping leads to a surface with low roughness and high precision. Because of required parts accuracy tool flatness is the key to the successful machining. To avoid its excessive thermal expansion, plate temperature research was taken. The goal was to determine the correlation between the basic lapping conditions and wheel temperature. In work Bulsara et al. authors developed model to estimate the maximum and average temperature...
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublikacjaThe paper discusses the effect of application of water-Al2O3 nanofluid, as a working fluid, on the efficiency of a flat plate solar collector. The mass concentration of nanoparticles was 0.1%, 0.2% and 0.4%. The tests were conducted for two values of radiation of about 1050 W/m2 and 400 W/m2, and volume flow rates of 60 l/h, 120 l/h and 170 l/h. The efficiency was calculated according to recommendations of the Polish Standard....
-
Applying of thin plate boundary condition in analysis of ship’s magnetic field
PublikacjaThis paper presents computer simulations of ship’s magnetic signatures using a new thin plate boundary condition implemented in the Opera-3d 18R2 program. The paper aims to check the magnetic signatures’ numerical calculations precision of objects using the thin plate boundary conditions and analysis of the magnetic signature of ship with a degaussing system and with and without inner devices.
-
Detection and size estimation of crack in plate based on guided wave propagation
PublikacjaThe paper presents results of the comprehensive theoretical and experimental investigation of crack detection in metallic plate using guided wave propagation. The main aim of the paper is to develop the novel method which would allow for linear crack size estimation with the use of minimal number of the transducers. In general, there exists the relation between length of the propagation path and the wave amplitude value. However,...
-
Performance of the flat plate solar collector operated with water-Al2O3 nanofluid
PublikacjaThis paper shows the experimental results of the performance a flat plate solar collector with water-Al2O3 nanofluid as a working fluid. The weight fractions of nanoparticles were 0.1%, 0.2% and 0.4%. The volume flow rate of nanofluid varied from 60 l/h to 170 l/h. The results show that application of nanofluids instead of pure water resulted in higher efficiency of the tested flat plate solar collector for given range of thermal...
-
Effect of surface roughness on thermal-hydraulic characteristics of plate heat exchanger
PublikacjaIn the paper the experimental analysis of passive heat transfer intensification in the case of modeled plate heat exchanger is conducted. The plate heat exchanger is chosen for the analysis because this kind of heat exchangers could be prospectively applied in the ORC systems, however other areas or application are equally possible. The experimental setup was assembled at the Department of Energy and Industrial Apparatus of Gdansk...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
Plate heat exchanger with porous structure for potential use in ORC system
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The passive intensification was obtained by a modification of the heat transfer surface, which was covered by a metallic porous microlayer. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one...
-
CAPABILITY OF IDENTIFYING AND PREDICTING THE TECHNICAL CONDITION OF PLATE HEAT EXCHANGERS IN OPERATION
PublikacjaThe paper presents a test stand for plate heat exchangers, allowing to identify the technical condition and to predict durability of the heat exchangers used aboard the sea-going ships: ”Oceanograf”, ”Władysław Orkan”and a passenger-car ferry, under the condition that they are of the same type and manufactured by the same company. In the first part three different installations with plate heat exchangers in the engine rooms...
-
Guided waves for monitoring of plate structures with linear cracks of variable length
PublikacjaDamage occurring at the work of plate structures may grow to a considerable size. The joint action – the detection of a defect at the earliest possible stage, the monitoring of its growth and the determination of its critical size in the context of structural reliability allows optimizing the cost of the maintenance and repair of structural elements. Thus the development of monitoring systems for permanent observation of fault...
-
The role of heterotrophic plate count bacteria in bottled water quality assessment
PublikacjaThe ever-growing popularity of bottled water is the result of many factors. One of the most relevant is the widespread belief that bottled water is safer for drinking than tap water. In fact many literature sources describe the rapid growth of the amounts of microorganisms in bottled water samples following the bottling process. The main purpose of this article is to collect the information on the factors which may affect this...
-
Effect of the Unit Pressure on the Selection Parameters of Intermetallic Coastings NiAl and Ni3Al after Platic Working
PublikacjaW artykule omówiono wpływ zgniotu na wybrane parametry warstwy międzymetalicznej NiAl i Ni3Al napawanej na stali C45 podanej obróbce plastycznej poprzez prasowanie na zimno.
-
Analiza przestępstwa niealimentacji w prawie polskim. Analysis of the crime of non-alimentation in Polish law.
PublikacjaPrzedmiotowa monografia (składająca się ze wstępu, ośmiu rozdziałów oraz zakończenia) dokonuje analizy zagadnienia przestępstwa niealimentacji w prawie polskim, zarówno w aspekcie historycznym, jak i w zakresie obecnie...
-
Numerical modelling of asymetric double-layer Al-Cu plate rolling process
PublikacjaNiekorzystnym zjawiskiem towarzyszącym procesom walcowania płaskich wyrobów bimetalowych jest krzywizna pasma na wyjściu z kotliny walcowniczej wynikająca z nierównomierności odkształcenia warstw bimetalowej blachy. Możliwość szybkiego i łatwego przeciwdziałania temu zjawisku daje wprowadzenie asymetrii prędkości bądź średnic walców roboczych. W przedstawionym artykule zaprezentowano badania komputerowe procesu walcowania blach...
-
Operational Properties Investigation of The Flat-Plate Solar Collector with Poliuretane Foam Insulation
Publikacja -
Thermal performance of a prototype plate heat exchanger with minichannels under boiling conditions
PublikacjaTo solve the problem and to meet the requirements of customers in the field of high heat fluxes transfer in compact units, a new design of plate heat exchanger with minichannels (minichannels PHE) was proposed. The aim was to construct a compact heat exchanger of high effectiveness for the purpose of household cogeneration ORC system. In this paper the experimental analysis of an assembled prototype of such compact heat exchanger...
-
Random field modelling of mechanical behaviour of corroded thin steel plate specimens
PublikacjaThe objective of this work is to explore the possibility of corrosion degradation modelling of thin steel plate specimens with the use of random field approach. The mechanical properties are obtained via the nonlinear Finite Element Analysis with the use of an explicit dynamic solver. The fully nonlinear material model is adopted to obtain the proper stress-strain response. Sensitivity analysis considering the main statistical...
-
Heat transfer and pressure drop characteristics of the silicone-based plate heat exchanger
PublikacjaThe paper presents an experimental investigation of a silicone based heat exchanger, with passive heat transfer intensification by means of surface enhancement. The main objective of this paper was to experimentally investigate the performance of a heat exchanger module with the enhanced surface. Heat transfer in the test section has been examined and described with precise measurements of thermal and flow conditions. Reported...
-
Shell model of multiple-row moment I-section end-plate joint
PublikacjaThe paper deals with a problem of application of shell elements in the models of multiple-row moment end-plate connections. The extended connection of I-section with a cross-section W760x265x220 made of steel S355 was analyzed. Comparison analysis of FEM, complex volume and shell models has been done. Three cases with different end-plate thickness: 14, 18 and 36 mm were analyzed and compared with the reference results. Comparison...
-
Pressure drop related to flow maldistribution in a model minichannel plate heat exchanger
PublikacjaThe paper describes the issues related to the pressure drop that accompanies the phenomenon of maldistribution of working fluid between the channels of a model minichannel plate heat exchanger. The research concerns a single exchanger's plate containing 51 (in every geometry) parallel rectangular minichannels of hydraulic diameters 461 µm, 571 µm, 750 µm and 823 µm. In addition, the more complex geometry has been investigated,...
-
Photocatalytical properties of maze-like MoO3 microstructures prepared by anodization of Mo plate
PublikacjaIn this work, we present a simple method of the formation of MoO3 microstructures via an electrochemical anodization of Mo plate carried out under varied conditions. The morphology, composition and structure of samples were investigated by SEM, EDX, XRD and Raman spectroscopy. The band gap energy was estimated using the Kubelka–Munk function and was found to be 2.87 eV. Finally, the photocatalytic activities of MoO3 samples were...
-
Bead-on-plate welding on S235JR steel by underwater local dry chamber process
PublikacjaThe article presents the results of the effect of parameters of underwater local dry chamber welding on the properties of padding welds. The effect of heat input and the type of shielding gas on the structure and hardness of welds was established. the functions for estimating the maximum hardness of the heat affected zone have been also elaborated.
-
Flow visualization and heat transfer investigations on the flat plate with streamwise pressure gradient
PublikacjaPaper presents experimental investigations results for film cooling on a flat plate. The main objective of the design is the streamwise pressure distribution on the flat plate as in the blade cascade. The transient and steady-state technique with liquid crystals for the surface temperature distribution with film cooling has been used in experiments in a low speed wind tunnel.
-
Effect of lag screw on stability of first metatarsophalangeal joint arthrodesis with medial plate
PublikacjaBackground: First metatarsophalangeal joint (MTP-1) arthrodesis is a commonly performed procedure in the treatment of disorders of the great toe. Since the incidence of revision after MTP-1 joint arthrodesis is not insignificant, a medial approach with a medially positioned locking plate has been proposed as a new technique. The aim of the study was to investigate the effect of the application of a lag screw on the stability and...
-
Modeling of free vibrations and resonant frequencies of simply-supported submerged horizontal plate
PublikacjaA theoretical approach was applied to study the vibration of simple-supported submerged horizontal plate. The derived analytical solution was used to determine natural frequencies for a horizontal plate vibrating in fluid. The investigations were conducted for a very wide range of material density and elasticity modulus covering all materials used in engineering practice. Analysis shows that plate vibration frequency decreases...
-
Experimental Research of an Axial Piston Pump with Displaced Swash Plate Axis of Rotation
PublikacjaThe article describes the influence of displacement of the swash plate rotation axis on the efficiency of axial piston pumps. The dead space volume was defined as the volume of the working chamber in the extreme position of the piston at the end of the pumping phase and its variability was determined as a function of the position of the axis of rotation of the swash plate and the swing angle of swash plate. The influence of swash...
-
Numerical simulation of damage detection in rectangular plate by two-dimensional wavelet transform.
PublikacjaW pracy przedstawiono metodę lokalizacji pęknięć w płytach przy zastosowaniu transformaty falkowej.
-
The effect of plate size on the natural convective heat transfer intensity of horizontal surfaces
PublikacjaW pracy przedstawiono badania wpływu rozmiarów płyty prostokątnej poziomej na intensywność wymiany ciepła w warunkach konwekcji swobodnej. Zaproponowano dwa zakresy: dla płyt o wymiarze charakterystycznym mniejszym niż 0,1 m - 0,2 m intensywność konwekcyjnej wymiany ciepła jest odwrotnie proporcjonalna do szerokości płyty, dla płyt szerszych niż 0,2 m szerokość płyty nie wpływa znacząco na współczynnik konwekcyjnej wymiany ciepła....
-
Hierarchia funkcji i celów obowiązku naprawienia szkody w polskim oraz niemieckim prawie karnym
Publikacja -
Quality of roof runoff waters from an urban region (Gdańsk, Poland)
PublikacjaW pracy przedstawiono wyniki badań analitycznych próbek wód spływnych z powierzchni dachów budynków z terenu miasta Gdańska. W próbkach oznaczano stężenia jonów (Na+, K+, NH4+, Mg2+, Ca2+, F-, Cl-, NO2-, PO4-, SO4-) oraz związków organicznych (pestycydy, węglowodory ropopochodne i lotne związki chlorowcoorganiczne). Dodatkowo mierzono pH oraz toksyczność próbek. Próbki zbierano przez okres 6 miesięcy w okresach po zakończeniu opadów....
-
Neuro-wavelet damage detection technique in beam, plate and shell structures with experimental validation
PublikacjaNiniejsza praca poświęcona jest technice diagnostyki konstrukcji bazującej na transfor-macie falkowej oraz sztucznych sieciach neuronowych (tzw. system neuro-wavelet). Zastosowanie analizy falkowej pozwala na lokalizację uszkodzeń wymagającą mini-malnej ilości danych wejściowych. W tym celu niezbędna jest tylko odpowiedź kon-strukcji pomierzona w wielu punktach. Poprawę efektywności lokalizacji zniszczeń uzyskano poprzez użycie...
-
The simultaneous detection of food dyes from different samples in a 96-well plate by spectrophotometry
Publikacja -
Significant Parameters Identification for Optimal Modelling of the Harp-Type Flat-Plate Solar Collector
Publikacja -
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublikacjaThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
-
THE EFFECT OF ALTERNATIVE CUTTER PATHS ON FLATNESS DEVIATIONS IN THE FACE MILLING OF ALUMINUM PLATE PARTS
PublikacjaIn this paper the relationships between the alternative machining paths and flatness deviations of the aluminum plate part, were presented. The flatness tolerance of the main surface of the plate part has crucial meaning due to the assembly requirement of piezoelectric elements on the radiator. The aluminum bodies under investigation are the base part of the radiators with crimped feathers for the train industry. The surface of...
-
Moment resistance of I-section end-plate roof girder splices; a case study
PublikacjaThis article deals with the problem of determining the resistance of end-plate connections. A nonlinear FEM model of the joint was constructed in order to predict its carrying capacity. A standard code procedure was done as well. The analyses have been done to assess atypical end-plate joints designed and constructed as a part of roof structures.
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublikacjaThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
Heat transfer in plate heat exchanger channels: experimental validation of selected correlation equations
PublikacjaThis study is focused on experimental investigation of selected type of brazed plate heat exchanger. The Wilson approach was applied in order to estimate heat transfer coefficients for the PHEx passages. The main aim of the paper was to experimentally check ability of several correlations published in the literature to predict heat transfer coefficients by comparison experimentally obtained data with appropriate predictions. The...
-
Influence of the position of the swash plate rotation axis on the volumetric efficiency of the axial pistons pumps
PublikacjaThe article describes the influence of the position of the swash plate axis of rotation on the size of the dead space and the volumetric efficiency of the axial pistons pump. Superposition of the two motions have been proposed - the rotation of the swash plate with respect to axis intersecting the axis of rotation of the pump shaft and the shifts of swash plate yielding a result of the rotation axis offset effect. In the article...
-
Influence of the Widespread Use of Corten Plate on the Acoustics of the European Solidarity Centre Building in Gdansk
PublikacjaThis paper describes the relationship between a strong architectural vision that is difficult to balance, and user expectations in terms of acoustics. The focus is on the use of corten steel as the dominant finishing material on façades and interiors to achieve an expressive, symbolic message through program-based design. The architectural premises justifying the adopted solutions are presented, especially the universality and...
-
Torque Transmitted by Multi-plate Wet Clutches in Relation to Number of Friction Plates and Their Dimensions
PublikacjaIn the paper results of experimental tests on multi-plate wet clutch torque capacity for various diameters and numbers of friction plates are presented. Construction of an apparatus for laboratory tests of wet clutch engagement, drag torque and maximum torque is shown. Methodology of maximum torque capacity experiment and hydraulic circuit diagram, which supplies a motor and an actuator for the experiment are described. Analytically...
-
Guided wave propagation in debonding detection in CFRP-reinforced steel plate-like structures
PublikacjaThe present study investigates the guided wave propagation in multilayered steel specimens reinforced with carbon fiber reinforced polymer (CFRP) through theoretical, numerical, and experimental means. The effectiveness of externally bonded reinforcement (EBR) relies heavily on the bonding quality between the CFRP and the substrate. Premature debonding, a prevalent and hazardous defect, can arise from suboptimal manufacturing processes,...
-
Determination of stepped plate thickness distribution using guided waves and compressed sensing approach
PublikacjaGuided waves recently have attracted significant interest as a very promising research area. The signals registered by a specially designed sensor network are processed to assess the state of the tested structure. Despite the constant development of novel damage detection algorithms employing guided waves, the phenomenon of wave propagation still needs detailed recognizing and understanding for the further progress of non-destructive...
-
Investigations of hydraulic jump configured by a two phase air water jetimpinging on a flat plate.
PublikacjaPrzedstawiono wyniki badań eksperymentalnych uskoku hydraulicznego powstającego przy napływie strugi uderzającej na powierzchnię płaskiej płyty.
-
Buckling and postcritical behaviour of the elastic infinite plate strip resting on linear elastic foudation
PublikacjaW pracy rozważa się problem von Karmana dla swobodnie podpartego pasma płytowego spoczywającego na sprężystym podłożu i poddanego równomiernie rozłożonemu obciążeniu ściskającemu na krawędzi podparcia. Krytyczne wartości parametrów wyznaczono na podstawie problemu zlinearyzowanego. Stan pokrytyczny badano za pomocą redukcji Liapunowa-Schmidta i twierdzenia Crandalla-Rabinowitza. Wykazano, że istnieje maksymalna częstość fal w kierunku...
-
Damage location in beam and plate structures by wavelet analysis of experimentally determined mode shapes
PublikacjaArtykuł dotyczy zastosowania analizy falkowej do lokalizacji uszkodzeń w konstrukcjach belkowych i płytowych. Wykonano testy dynamiczne belki wspornikowej i płyty utwierdzonej wzdłuż jednej z krawędzi. Lokalizację defektu otrzymano za pomocą transformaty falkowej eksperymentalnie wyznaczonych postaci drgań.
-
Katarzyna Weinerowska-Bords dr hab. inż.
Osoby -
Konieczne zmiany w prawie polskim uwzględniające zwrot nakładów za usługi związane z wodami opadowymi
PublikacjaPrzedstawiono zagadnienia prawne związane z finansowaniem zagospodarowania wód opadowych. Przegląd istniejących regulacji. Konieczne zmiany.
-
Miejsce i znaczenie nauczania praktycznego w planie studiów inżynierskich na Wydziale Mechanicznym Politechniki Gdańskiej
PublikacjaReferat dotyczy znaczenia nauczania praktycznego w kształceniu inżynierów mechaników na przykładzie Wydziału Mechanicznego Politechniki Gdańskiej. Przedstawiono w nim strukturę studiów, sylwetkę i kwalifikacje absolwentów oraz metody nauczania inżynierów. Omówiono proces dostosowania planów studiów i programów nauczania do wymogów Deklaracji Bolońskiej.Dużą uwagę skupiono na takich formach nauczania inżynierów, jak nauczanie grupowe...