Filters
total: 652
filtered: 597
Search results for: HYBRID BEAMS, AIR CONCRETE, PRESTRESSED CONCRETE, PREFABRICATED LINTEL
-
Modeling the effect of electric vehicles on noise levels in the vicinity of rural road sections
PublicationNumerous European countries experience a steady increase in the share of electric (EV) and hybrid electric (HEV) vehicles in the traffic stream. These vehicles, often referred to as low- or zero-emission vehicles, significantly reduce air pollution in the road environment. They also have a positive effect on noise levels in city centers and in the surroundings of low-speed roads. Nevertheless, issues related to modeling noise from...
-
The potential of raw sewage sludge in construction industry – A review
PublicationExcess sewage sludge produced in any municipal or industrial wastewater treatment plant becomes a serious problem due to its increasing amount. This increase is related to the improvement of treatment technologies, expansion of sewage systems and the development of new industrial plants. The implementation and development of new technologies related to the utilization of sewage sludge is currently based on treating it as a substrate....
-
Testing of low temperature behaviour of asphalt mixtures in bending creep test
PublicationThe paper presents a method of bending beam test and its importance for evaluation of asphalt mixtures behaviour at low temperatures. Two types of asphalt mixtures: asphalt concrete AC with normal paving grade bitumen and stone mastic asphalt SMA with SBS-modified bitumen were tested. Long-term oven ageing (LTOA) test was also used in the laboratory according to SHRP procedure. The Burgers model was applied and rheological parameters...
-
DESIGN AND CONSTRUCTION OF TILTED WALLS IN ACCORDANCE WITH CODES' PROVISIONS ON THE EXAMPLE OF THE CONSTRUCTION OF THE MUSEUM OF THE SECOND WORLD WAR IN GDAŃSK
PublicationThe purpose of this article was to introduce the design and construction of tiled walls in accordance to codes' restrictions. The construction of the Museum of the Second World War in Gdańsk was chosen to be an example of its successful use in practice. Theoretical knowledge was based on PN-EN 1992-1-1:2008 and fib Model Code for Concrete Structures 2010. Although codes' recommendations seem curt, practice prove structural advance....
-
Polymeric Bearings as a new base isolation system suitable for mitigating machine-induced vibrations
PublicationThe present paper summarizes the preliminary results of the experimental shaking table investigation conducted in order to verify the effectiveness of a new base isolation system consisting of Polymeric Bearings in reducing strong horizontal machine-induced vibrations. Polymeric Bearing considered in the present study is a prototype base isolation system, which was constructed with the use of a specially prepared flexible polymer...
-
Utilization of Gaseous Carbon Dioxide and Industrial Ca-rich Waste for Calcium Carbonate Precipitation: A Review
PublicationTechnologies for the management of various types of waste and the production of useful products from them are currently widely studied. Both carbon dioxide and calcium-rich waste from various production processes are problematic wastes that can be used to produce calcium carbonate. Therefore, the purpose of this paper is to provide an overview about the state of the development of processes that use these two wastes...
-
Shear Cap Size Selection Method Based on Parametric Analysis of ACI-318 Code and Eurocode 2 Standard
PublicationThe scope of the paper is to propose a method for determining the size of shear caps in a slab–column-connections-reinforced concrete structure. Usually, shear heads are used to enhance slab–column connection, especially when the transverse reinforcement does not give the required punching shear load capacity. The dimensions of the shear head should provide the punching shear resistance of the connection inside and outside the...
-
Właściwości niskotemperaturowe betonów asfaltowych o wysokim module sztywności (AC-WMS) w badaniach trzypunktowego zginania
PublicationArtykuł przedstawia właściwości niskotemperaturowe betonów asfaltowych o wysokim module sztywności. Przedstawione wyniki zostały uzyskane w dwóch badaniach zginania trzypunktowego próbek belkowych: ze stałą prędkością przemieszczenia oraz pod stałym obciążeniem. Obie te metody są od dawna stosowane na Politechnice Gdańskiej do oceny właściwości niskotemperaturowych betonów asfaltowych. Badaniu poddano pięć betonów asfaltowych –...
-
Method of determining the degree of liquid aeration in a variable capacity displacement pump
PublicationThe Author concludes, that there is a possibility of determining a concrete value of the liquid aeration coefficient during the pump operation by finding such value of coefficient with which the increase of torque of mechanical losses is proportional to the indicated torque determined with a fixed value of increase of pressure in the pump working chambers. The fixed value of increase of pressure assumed in searching the liquid...
-
Projektowanie budynków użyteczności publicznej narażonych na ataki terrorystyczne z wykorzystaniem systemu ochrony pasywnej
PublicationW artykule przedstawiono projektowanie systemów ochrony pasywnej w budynkach użyteczności publicznej, które mogą posłużyć jako przykład i stanowić podstawę do dalszych założeń przy projektowaniu budynków narażonych na obciążenie wybuchem spowodowanym przez ataki terrorystyczne. W pracy przeprowadzono symulacje numeryczne na przykładzie ściany budynku użyteczności publicznej wykonanego w technologii żelbetowej. Obliczenia wykonano...
-
Recommendations for Urban Freight Policy Development in Gdynia
PublicationThe purpose of this paper was to provide practical recommendations on how to develop Gdynia’s urban freight policy based on actual planning experience and characteristics of potential measures. Freight policy scheme was developed as a result of three interrelated factors: a) the general procedure of the urban freight planning, b) the city's current planning stage analysis and, c) characteristics of urban freight objectives and...
-
Models of Structures in Didactics
PublicationThe final aim of teaching students subjects, such as structural mechanics, reinforced concrete, and steel structures is to teach them how structures work in a given building as well as to provide them with skills enabling them to calculate and design structures. The behavioral model of the structure, contrary to the architectural model, which focuses mainly on the external form of the building, shows workings from both the static...
-
Photogrammetric and total station's measurement of compressed column's model
PublicationModelling studies continue to play an important role. One of such study is stress determination in the reinforcement bars of reinforced columns and determine column's axis deformation. The article presents measurements results of control points located on the model of reinforced concrete column. The column was compressed in few series till it's destruction. In this studies, photogrammetric method and total station measurements...
-
A Survey of Fast-Recovery Mechanisms in Packet-Switched Networks
PublicationIn order to meet their stringent dependability requirements, most modern packet-switched communication networks support fast-recovery mechanisms in the data plane. While reactions to failures in the data plane can be significantly faster compared to control plane mechanisms, implementing fast recovery in the data plane is challenging, and has recently received much attention in the literature. This survey presents a systematic,...
-
Numerical Study on Seismic Response of a High-Rise RC Irregular Residential Building Considering Soil-Structure Interaction
PublicationThe objective of the present study is to investigate the importance of soilstructure interaction effects on the seismic response of a high-rise irregular reinforced-concrete residential building. In order to conduct this research, a detailed three-dimensional structure model was subjected to various earthquake excitations, also including a strong mining tremor. Soil-foundation flexibility was represented using the spring-based...
-
Optimized Computational Intelligence Model for Estimating the Flexural Behavior of Composite Shear Walls
PublicationThis article presents a novel approach to estimate the flexural capacity of reinforced concrete-filled composite plate shear walls using an optimized computational intelligence model. The proposed model was developed and validated based on 47 laboratory data points and the Transit Search (TS) optimization algorithm. Using 80% of the experimental dataset, the optimized model was selected by determining the unknown coefficients of...
-
Direct design of Controlled Modulus Columns (CMC) based on in-situ testing
PublicationIn this paper, the serviceability limit state and bearing capacity of tension screw displacement piles were analyzed using the results of static pile load tests, carried out on the test plot near the Elbląg city, and field, and laboratory tests. The paper presents the methodology of determining the pile load-settlement curve using different types of t-z transfer functions. The new method of constructing the pile load-settlement...
-
Wave Method for Structural Health Monitoring: Testing Using Full-Scale Shake Table Experiment Data
PublicationAn algorithm of the wave method for structural health monitoring (SHM) is tested and calibrated using shake table experiment data of a full-scale, seven-story, reinforced-concrete building slice. The method is based on monitoring changes in the velocity of waves propagating vertically through the structure, identified by least-squares (LSQ) fit of beam models. The experiment was conducted by a team from the University of California,...
-
The use of fibre-reinforced polymers (FRP) in bridges as a favourable solution for the environment
PublicationThe purpose of this article is to show the modern engineering, in which sustainability and taking care of ecology play a significant role. The authors are focused on FRP composite materials and their applications in civil engineering. Case studies showing renovation and design of new bridges with the use of FRP are presented and discussed to clarify benefits, which this solution provides. Main advantages of FRP materials in comparison...
-
A HISTORICAL BUILDING'S RESTORATION IN THE CONSTRUCTIONAL ASPECT ON THE EXAMPLE OF A BUILDING LOCATED IN POLAND
PublicationObjects of cultural heritage are an extremely important element in the proper functioning of the social life. They provide information on our ancestors' actions, as well as shape our culture and social awareness. It is important for the historical objects to provide those information accurately, that is without any unnecessary human intervention over the years of the monument's existence. However, it is not always possible due...
-
Influence of the Shear Cap Size and Stiffness on the Distribution of Shear Forces in Flat Slabs
PublicationThe scope of this paper is to investigate analytically and numerically the influence of shear cap size and stiffness on the distribution of shear forces in flat slabs in a slab–column-connections-reinforced concrete structure. The effect of support (shear cap) stiffness on the calculation of the length of the shear control perimeter according to the available methods is presented. Based on the analysis, the authors indicate in...
-
Mechanics of Micro- and Nano-Size Materials and Structures
PublicationNanotechnology knowledge is always looking to expand its boundaries to achieve the mostsignificant benefit to human life and meet the growing needs of today. In this case, we can refer tomicro- and nanosensors in micro/nano-electromechanical systems (MEMS/NEMS). These electricaldevices can detect minimal physical stimuli up to one nanometer in size. Today, micro/nano-sensordevices are widely used in the...
-
Short-Term Observations of Rainfall Chemistry Composition in Bellsund (SW Spitsbergen, Svalbard)
PublicationGlobal warming results in increasingly widespread wildfires, mostly in Siberia, but also in North America and Europe, which are responsible for the uncontrollable emission of pollutants, also to the High Arctic region. This study examines 11 samples of rainfall collected in August in a coastal area of southern Bellsund (Svalbard, Norway). It covers detailed analysis of major ions (i.e., Cl−, NO3−, and SO42−) and elements (i.e.,...
-
Design and Synthesis of NTU-9/C3N4 Photocatalysts: Effects of NTU-9 Content and Composite Preparation Method
PublicationHybrid materials based on graphitic carbon nitride (g-C3N4) and NTU-9 metal–organic frameworks (MOF) were designed and prepared via solvothermal synthesis and calcination in air. The as-prepared photocatalysts were subsequently characterized using Brunauer–Emmett–Teller (BET) analysis, UV-Vis diffuse reflectance spectroscopy (DRS), photoluminescence (PL) emission spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy...
-
Application and modelling of Shape-Memory Alloys for structural vibration control: State-of-the-art review
PublicationOne of the most essential components of structural design for civil engineers is to build a system that is resistant to environmental conditions such as harsh chemical environments, and catastrophic disasters like earthquakes and hurricanes. Under these circumstances and disturbances, conventional building materials such as steel and concrete may demonstrate inadequate performance in the form of corrosion, deterioration, oxidizing,...
-
Investigation on Damage-Involved Structural Response of Colliding Steel Structures during Ground Motions
PublicationEarthquakes are the most unpredictable damaging loads which can affect civil engineering structures. Due to insufficient separation distance between adjacent structures with different dynamic properties, structural collisions may occur during ground motions. Although the research on structural pounding has recently been much advanced, the studies have mainly been conducted for concrete structures. The aim of this paper is to show...
-
Reduction of noise and rolling resistance by horizontal grinding of asphalt pavements
PublicationGrinding of cement concrete pavements to reduce unevenness and noise is common since a long time. Grinding is then made with wheels equipped with diamond blades rotating in the vertical plane. This creates narrow vertical/longitudinal grooves in the pavement. It is not applied to asphalt pavements. In this paper an alternative type of grinding is studied. In this case plates with diamond heads rotate in the same plane as the pavement,...
-
Chemical surface etching methods for ground tire rubber as sustainable approach for environmentally-friendly composites development– a review
PublicationGround tire rubber (GTR) has been used as a sustainable low-cost modifier in various composites. However, due to the hydrophobic nature of GTR, it is in compatible with most matrices and results in deterioration in both mechanical and physical properties of composites. This necessitates pre-modification of the powdered rubber to improve the interfacial bonding at the rubber-matric interface. The most common GTR modification research...
-
Influence of Selected Warm Mix Asphalt Additives on Cracking Susceptibility of Asphalt Mixtures
PublicationWarm mix asphalt (WMA) has been widely accepted as a future asphalt paving technology. Besides clear advantages, there are still some concerns regarding durability and long-term performance of pavements made with this type of asphalt mixtures. One of the most important issues is low temperature behaviour of WMA because certain additives used for temperature reduction can aect bitumen properties. This paper presents the evaluation...
-
Two-Level Multivariable Control System of Dissolved Oxygen Tracking and Aeration System for Activated Sludge Processes
PublicationThe problem of tracking dissolved oxygen is one of the most complex and fundamental issues related to biological processes. The dissolved oxygen level in aerobic tanks has significant influence on behaviour and activity of microorganism inhabiting the plant. Aerated tanks are supplied with air from an aeration system (blowers, pipes, throttling valves, diffusers). It is a complex dynamic system governed by nonlinear hybrid dynamics....
-
Assessment of under power ed propulsion machinery in electrically driven small inland waterway passenger ships from classification society point of view
PublicationPaper presents short operat ional a nd engineering analysis of underpowered propulsion in small electrically propelled small inland passenger ships. There is evidence that in certain weather conditions the phenomena of added aerodynamic resistance of small water crafts may have seriou s influence on their speed and manoeuvrability. Existing regulations like class societies rules for ship classification and construction or EU Directive 2006/87/EC do...
-
ASSESSMENT OF UNDERPOWER ED PROPULSION MACHINERY IN ELECTRICALLY DRIVEN SMALL INLAND WATERWAY PASSENGER SHIPS FROM CLASSIFICATION SOCIETY POINT OF View
PublicationPaper presents short operat ional a nd engineering analysis of underpowered propulsion in small electrically propelled small inland passenger ships. There is evidence that in certain weather conditions the phenomena of added aerodynamic resistance of small water crafts may have serious influence on their speed and manoeuvrability. Existing regulations like class societies rules for ship classification and construction or EU Directive 2006/87/EC do...
-
Doraźna nośność słupów o przekroju kołowym z rur FRP wypełnionych betonem Badania, teoria, obliczanie
PublicationPraca ma charakter monografii opisującej aktualny stan wiedzy z zakresu badań, teorii i projektowania słupów CFFT (concrete-filled fiber-reinforced polymer tube). Celem prowadzonych przez autora prac studialnych i badań własnych, w tym eksperymentalnych, jest szczegółowa analiza doraźnej nośności i zachowania się słupów CFFT poddanych ściskaniu osiowemu i mimośrodowemu. W pierwszym rozdziale wyjaśniono motywację autora do podjęcia...
-
Nonlinear numerical simulation of earthquake-induced pounding between timber frame buildings
PublicationEarthquakes may induce serious dynamic loads acting on buildings, which can lead to damage or even destruction of the whole structure. In densely populated areas, it is quite common that buildings are located very close one to another which can result in pounding between them during ground motions. Due to the environmental awareness, multi-story timber frame buildings are gaining popularity and therefore there is a need to investigate...
-
Factors affecting low-temperature cracking of asphalt pavements: analysis of field observations using the ordered logistic model
PublicationAccurate identification of factors that primarily affect the number of low-temperature cracks is crucial for selection of road materials and planning of pavement maintenance. Field investigations of lowtemperature cracks were performed in the years 2014 and 2020 on the same 68 road sections being in service in typical traffic conditions. The collected data were statistically analysed using the ordered logistic regression model....
-
Time travel without paradoxes: Ring resonator as a universal paradigm for looped quantum evolutions
PublicationA ring resonator involves a scattering process where a part of the output is fed again into the input. The same formal structure is encountered in the problem of time travel in a neighborhood of a closed timelike curve (CTC). We know how to describe quantum optics of ring resonators, and the resulting description agrees with experiment. We can apply the same formal strategy to any looped quantum evolution, in particular to the...
-
EVALUATION OF 3D MODEL OF REBAR FOR QUANTITATIVE PARAMETERS
PublicationThe construction industry practices and processes are evolving constantly, and with the emergence of Industry 4.0, the use of technologies is expanding. Construction progress monitoring is an essential project lifecycle process; project success and timely completion are linked with effective progress monitoring operations and adopted tools. In the domain of automated construction progress monitoring, 3D modeling techniques have...
-
Screw displacement pile shaft deformations measured by vibrating wire and fiber optic systems during a static load test
PublicationThis paper describes a full scale static load test performed on a 400 mm diameter screw displacement pile equipped with four different strain measuring systems. Three types of vibrating wire strain gauges (VWSG) were used: global - retrievable, local attached to steel pipe and local concrete embedded. The fourth system was distributed fiber optic sensors based on Rayleigh back scattering (DFOS) - three in the pile cross section....
-
The Application of Granulated Expanded Glass Aggregate with Cement Grout as an Alternative Solution for Sub-Grade and Frost-Protection Sub-Base Layer in Road Construction
PublicationThe purpose of the research was to assess the possibility of using granulated expanded glass aggregate (GEGA) with cement grout as a replacement of a sub-grade and frost-protection layer, made of natural fine aggregates (NATU), stabilized with a hydraulic binder. Instead of traditional parts of the road construction, such as the sub-grade and frost-protection layer with the application of fine aggregate, stabilized with cement,...
-
Introducing a Computational Method to Retrofit Damaged Buildings under Seismic Mainshock-Aftershock Sequence
PublicationRetrofitting damaged buildings is a challenge for engineers, since commercial software does not have the ability to consider the local damages and deformed shape of a building resulting from the mainshock record of an earthquake before applying the aftershock record. In this research, a computational method for retrofitting of damaged buildings under seismic mainshock-aftershock sequences is proposed, and proposed computational...
-
Assessment of the impact of jet impingement technique on the energy efficiency of air-cooled BIPV/T roof tile
PublicationThe paper concerns a numerical analysis of cooling of the hybrid photovoltaic (PV) modules dedicated to Building-Integrated Photovoltaic/Thermal (BIPV/T) systems. Attention was focused on the photovoltaic roof tiles, using a jet impingement technique, in which the intensification of heat transfer is ensured by streams of air hitting the heat exchange partition. A series of numerical simulations were carried out to assess an influence...
-
Unfolding new values in the landscape of conflict
PublicationThe main objective of the paper is to investigate how the conflict quality of landscape can be used as its asset and potential for creating new values. Like mediation between different overlapping archaeologies offers a basis for the perception of place in the chronology of time, the mediation between conflicted areas creates a capacious zone for enhancing the unique quality of landscape in its architectural, social, cultural and...
-
The best porous asphalt pavement in Sweden so far
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Seismic damage diagnosis in adjacent steel and RC MRFs considering pounding effects through improved wavelet-based damage-sensitive feature
PublicationThis paper aims to propose complex Morlet (cmorfb-fc) wavelet-based refined damage-sensitive feature (rDSF) as a new and more precise damage indicator to diagnose seismic damages in adjacent steel and Reinforced Concrete (RC) Moment Resisting Frames (MRFs) assuming pounding conditions using acceleration responses. The considered structures include 6- and 9-story steel and 4- and 8-story RC benchmark MRFs that are assumed to have...
-
Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test
PublicationLow-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...
-
Acoustic lifecycle study of the double-layer porous asphalt on E4 in Huskvarna, Sweden
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed on the E4 motorway through the Swedish city Huskvarna. Earlier experience in Sweden indicated that it was feasible to obtain a high initial noise reduction but due to the widespread use of studded tires in winter, clogging and ravelling created losses of around 2 dB per year, with an expected acoustical lifetime of only 3 years. However, the improved...
-
Correlation between Compressive Strength and Heat of Hydration of Cement Mortars with Siliceous Fly Ash
PublicationThis paper presents the results of calorimetric and strength tests of mortars with ordinary Portland cement and two substitution rates (10 and 20%) of cement by siliceous fly ash. The prepared samples were cured under isothermal conditions at four different temperatures: 23, 33, 43 and 53 °C. Heat of hydration was measured using an isothermal calorimeter dedicated to monitor the hydration process of cementitious composites such...
-
Desulfurization of raw naphtha cuts using hybrid systems based on acoustic cavitation and advanced oxidation processes (AOPs)
PublicationA combination of dual-frequency acoustic cavitation (acoustic cavitation) and UV assisted advanced oxidation processes (AOPs) reaction system was developed for desulfurization of raw naphtha used to produce aviation fuels. Various types of oxidants in hybrid systems including hydrogen peroxide, acetic acid, acetone, air and ozone were compared. At optimum oxidant to sulfur compounds molar ratio (rox) of 5.0, the hybrid process...
-
Analiza kosztów i czasu budowy domu jednorodzinnego w technologii drewna krzyżowo klejonego CLT
Publication-
-
The importance of the bottom layer in double-layer porous asphalt for noise reduction
PublicationDouble-layer porous asphalt concrete (DPAC) surfaces are generally considered to be the acoustically most effective low noise road surfaces ready for implementation. While DPAC used on highways in warm climates may have an average life of around 8 years, in Scandinavia with severe winter climate DPAC usually survive only about 3 years; partly due to wear of studded tyres. An ongoing project in Sweden, applying DPAC and single-layer...