Search
Search results for: AIR COOLING
-
Measurement of the temperature change of PVCP tissue phantom illuminated by dermatological laser 1.series
Open Research DataApplication of laboratory set-up for characterization of thermal properties of optical tissue phantoms during laser irradiation is presented. The produced system utilizes a thermographic camera VIGOcam v50 and a dermatological laser system with a 975 nm diode laser module. The set-up was used to perform measurements of the temporal and spatial temperature...
-
Promising Nanoparticle-Based Heat Transfer Fluids—Environmental and Techno-Economic Analysis Compared to Conventional Fluids
PublicationProviding optimal operating conditions is one of the major challenges for effective heating or cooling systems. Moreover, proper adjustment of the heat transfer fluid is also important from the viewpoint of the correct operation, maintenance, and cost efficiency of these systems. Therefore, in this paper, a detailed review of recent work on the subject of conventional and novel heat transfer fluid applications is presented. Particular...
-
Interaction of Acoustic and Thermal Modes in the Gas with Nonequilibrium Chemical Reactions: Possibilities of Acoustic Cooling
PublicationNonlinear generation of thermal mode during propagation of dominative sound in a chemically reacting gas is considered. The dynamic equation of excess temperature associated with the thermal mode is derived. It is instantaneous and includes quadratic nonlinear acoustic source reflecting the nonlinear character of interaction between acoustic and non-acoustic types of gas motion. Both periodic and aperiodic sound may be considered...
-
THERMAL ANALYSIS AND DESIGN OF HYBRID MICROCHANNEL-MICROJET TEST PROBE
PublicationThe paper presents the numerical investigation of a microjet- microchannel cooling module. In which microjets of water are impinging into the microchannels and forming a liquid film on the impingement surface. Applied technology takes benefits from two very attractive heat removal techniques. When lminar jets are impinging on the surface have a very high kinetic energy at the stagnation point, also in microchannels boundary layer...
-
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublicationWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
On description of periodic magnetosonic perturbations in a quasi-isentropic plasma with mechanical and thermal losses and electrical resistivity
PublicationMagnetosonic periodic perturbations in a uniform and infinite plasma model are considered. Damping due to compressional viscosity, electrical resistivity, and thermal conduction are taken into account, as well as some heating–cooling function, which may destroy the isentropicity of wave perturbations. The wave vector forms arbitrary angle h with the equilibrium straight magnetic field, and all perturbations are functions...
-
On the Nonlinear Effects of Magnetoacoustic Perturbations in Optically Thin Quasi-Isentropic Plasmas
PublicationNonlinear effects of planar magnetosound perturbations in a plasma are discussed. Plasma is non-adiabatic due to optically thin radiation and external heating. For these reasons, thermal instability of a plasma may appear which makes it acoustically active. The plasma is assumed to be initially homogeneous ideal gas with infinite electrical conductivity permeated by a straight magnetic field which is orthogonal to the trajectories...
-
SAMPLE-AND-HOLDING METHOD FOR GAS SENSING APPLIED FOR RESISTANCE GAS SENSORS
PublicationThe DC resistance of a Taguchi gas sensor is influenced by the ambient gas. To improve the selectivity and sensitivity of a sensor the fluctuation enhanced sensing (FES) was used. The paper proposes a novel methodology of utilizing FES technique that sample composition of an ambient atmosphere and hold it for further processing (sample-and-holding technique). The method uses the heated gas sensor to sample an ambient atmosphere...
-
Relations between magnetosonic perturbations as an indicator of a magnetosonic exciter and equilibrium parameters of a plasma
PublicationThe thermodynamic relations between perturbation of pressure and pertur- bation of mass density and between components of velocity which specify a magnetosonic wave are theoretically studied. A planar flow with the wave vec- tor forming a constant angle with the equilibrium magnetic field is investigated. The theory considers deviation from the adiabaticity of a flow due to some kind of heating–cooling function and thermal conduction...
-
Selected aspects of determining the reliability of the pump subsystems with redundancy, used in main engine auxiliary systems
PublicationThe rules of classification societies require the use of redundancy in the systems essential for the safety of the ship. Duplication of pumps in the main engine auxiliary systems like cooling water system, lubricating oil system, fuel oil system is a good example here. Therefore, in the author's opinion, some attention should be paid to this issue. Two important questions arise here. Does duplication of pumps in marine systems...
-
Numerical simulations of transonic flow with film cooling and jet vortex generators
PublicationW pracy przedstawiono wyniki obliczeń przepływu transonicznego na stronie ssącej łopatki turbiny gazowej. Obliczenia wykonano dla geometrii komory pomiarowej w tunelu transonicznym IMP PAN, zaprojektowanej tak, aby odwzorować warunki przepływowe istniejące w palisadzie turbinowej. Przedstawiono wyniki obliczeń przepływu z zastosowaniem otworów chłodzących (film cooling) oraz strumieniowych generatorów wirów. Porównano je z danymi...
-
Innovative Railway Stations
PublicationIn relation to modern demographic trends, evolving technologies and environmentfriendly solutions increases the potential of rail considered as sustainable form of public transport. Contemporary tendencies of designing railway stations in Europe are focused on lowering energy consumption and reducing carbon emission. The main goal of the designers is to create a friendly and intuitive space for its users and at the same time a...
-
Possibilities and benefits of a new method of modifying conventional building materials with phase-change materials (PCMs)
PublicationThe paper presents a current study devoted to the optimization of the amount of PCM present within traditional building materials, utilized in this case in hollow-brick walls. Authors focus on proposing an alternative to typical direct addition of PCM to existing building materials: introducing two- and three-component mixtures, based on a porous PCM carrier, which in this case was construction aggregate. Preliminary studies of...
-
Assessment of Tensile Strength Reserve of Asphalt Mixtures at Low Temperatures
PublicationDuring winter conditions, low-temperature cracks develop at the surface of the asphalt pavement when tensile thermal stress induced in the asphalt layer during cooling equals and exceeds the tensile strength of the material. The paper presents the results of tensile strength reserve assessment of asphalt mixtures with neat and SBS-polymer modified bitumen application. The tensile strength reservewas calculated as difference between...
-
Standing Acoustic Waves and Relative Nonlinear Phenomena in a Vibrationally Relaxing Gas-Filled Resonator
PublicationStanding acoustic waves in one-dimensional resonator filled with vibrationally relaxing gas, are studied. Two regimes of excitation of molecular vibrational degrees of freedom are considered, equilibrium and nonequilibrium. The acoustic energy enlarges with time in the non-equilibrium regime and decreases otherwise before formation of discontinuity. After that, it decreases due to nonlinear absorption and tends to zero in equilibrium...
-
Corrigendum to “Fatigue life improvement using low transformation temperature weld material with measurement of residual stress” [Int. J. Fatigue 164 (2022) 107137]
PublicationWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
Fatigue life improvement using low transformation temperature weld material with measurement of residual stress
PublicationWelding processes often produce high levels of tensile residual stress. Low transformation temperature (LTT) welding wires utilise phase transformation strains to overcome the thermal contraction of a cooling weld. In this paper, the residual stress within each weld was quantified using the milling/strain gauge method, being the strain change measured as the weldment was milled away. The fatigue tests were conducted under uniaxial...
-
ARRAY OF MINIJETS – THERMAL AND HYDRAULIC PHENOMENA IN BOUNDARY LAYER
PublicationPresented work considers flow and thermal phenomena occurring in the system consisting of minijets array and heated with constant heat flux surface. Numerical analyses, based on the mass, momentum and energy conservation laws, were conducted. Focus was placed on the proper model construction, in which turbulence and boundary layer modelling was crucial. Calculations were done for various mass flow rates. The main calculations were...
-
Instantaneous Heating and Cooling Caused by Periodic or Aperiodic Sound of Any Characteristic Duration in a Gas with Vibrational Relaxation
PublicationThermodynamic relaxation of internal degrees of a molecule's freedom in a gas occurs with some characteristic time. This makes wave processes in a gas behave differently depending on the ratio of characteristic duration of perturbations and the relaxation time. In particular, generation of the secondary non-wave modes by intense sound in a nonlinear flow dependens on frequency. These kinds of interaction are considered in this...
-
Linear impedance of V2O5 nanorods obtained at 903K
Open Research DataThe DataSet contains the linear electrical properties of V2O5 nanorods which were measured by the impedance spectroscopy method. V2O5 nanorods were obtained by the sol-gel method. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The precursor powder was pressed into the disk-shaped pellets (12mm in diameter...
-
Linear impedance of V2O5 nanorods obtained at 913K
Open Research DataThe DataSet contains the linear electrical properties of V2O5 nanorods which were measured by the impedance spectroscopy method. V2O5 nanorods were obtained by the sol-gel method. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The precursor powder was pressed into the disk-shaped pellets (12mm in diameter...
-
Linear impedance of V2O5 nanorods obtained at 893K
Open Research DataThe DataSet contains the linear electrical properties of V2O5 nanorods which were measured by the impedance spectroscopy method. V2O5 nanorods were obtained by the sol-gel method. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The precursor powder was pressed into the disk-shaped pellets (12mm in diameter...
-
A New Approach for the Mitigating of Flow Maldistribution in Parallel Microchannel Heat Sink
PublicationThe problem of flow maldistribution is very critical in microchannel heat sinks (MCHS). It induces temperature nonuniformity, which may ultimately lead to the breakdown of associated system. In the present communication, a novel approach for the mitigation of flow maldistribution problem in parallel MCHS has been proposed using variable width microchannels. Numerical simulation of copper made parallel MCHS consisting of 25 channels...
-
Magnetoacoustic Heating in Nonisentropic Plasma Caused by Different Kinds of Heating-Cooling Function
PublicationThe nonlinear phenomena which associate with magnetoacoustic waves in a plasma are analytically studied. A plasma is an open system with external inflow of energy and radiation losses. A plasma’s flow may be isentropically stable or unstable. The nonlinear phenomena occur differently in dependence on stability or instability of a plasma’s flow. The nonlinear instantaneous equation which describes dynamics of nonwave entropy mode...
-
Macroscopic examination of CuNiFeR pipeline
Open Research DataCopper and nickel alloys called cunifers (Cu, Ni, Fe and R – rest of alloy elements) have found wide application in the production of ship pipeline components in contact with sea water, such as, for example, the main engine cooling system. These alloys are characterized by a very high corrosion resistance, which is ensured by appropriately carried out...
-
Microscopic examination of CuNiFeR pipeline
Open Research DataCopper and nickel alloys called cunifers (Cu, Ni, Fe and R – rest of alloy elements) have found wide application in the production of ship pipeline components in contact with sea water, such as, for example, the main engine cooling system. These alloys are characterized by a very high corrosion resistance, which is ensured by appropriately carried out...
-
Linear impedance of V2O5 nanorods obtained at 923K
Open Research DataThe DataSet contains the linear electrical properties of V2O5 nanorods which were measured by the impedance spectroscopy method. V2O5 nanorods were obtained by the sol-gel method. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The precursor powder was pressed into the disk-shaped pellets (12mm in diameter...
-
Sodium nitrite as a corrosion inhibitor of copper in simulated cooling water
PublicationThe corrosion inhibition behavior of sodium nitrite (NaNO2) towards pure copper (99.95%) in simulated cooling water (SCW) was investigated by means of electrochemical impedance spectroscopy (EIS) and dynamic electrochemical impedance spectroscopy (DEIS). NaNO2 interferes with metal dissolution and reduce the corrosion rate through the formation or maintenance of inhibitive film on the metal surface. Surface morphologies illustrated...
-
Nonlinear generation of non-acoustic modes by low-frequency sound in a vibrationally relaxing gas
PublicationTwo dynamic equations referring to a weakly nonlinear and weakly dispersive flow of a gas in which molecular vibrational relaxation takes place. are derived. The first one governs an excess temperature associated with the thermal mode, and the second one describes variations in vibrational energy. Both quantities refer to non-wave types of gas motion. These variations are caused by the nonlinear transfer of acoustic energy into...
-
The Effect of Welding Conditions on Diffusible Hydrogen Content in Deposited Metal
PublicationThe article presents the results of a literature survey and preliminary tests which set out effects of welding conditions on the amount of diffusible hydrogen in deposited metal. Experiments were conducted by using rutile coated electrodes which generate high contents of diffusible hydrogen in deposited metal. The amount of diffusible hydrogen was determined by a glycerin test.Eleven factors were considered: the electrode angle,...
-
Nowoczesne metody termochemicznej konwersji biomasy w paliwa gazowe, ciekłe i stałe = Modern methods of thermochemical biomass conversion into gas, liquid and solid fuels
PublicationBiomass utilization through direct- or co-combustion with coal, based on coal, hydrogen and oxygen compounds chemical energy conversion into heat in boilers, is simultaneously the cheapest and - according to experts - economically least effective solution. In case of heat and electricity production in cogeneration process in biomass fueled heat and power stations (wood, straw, energetic plants, RDF etc), investment costs are little...
-
Performance Evaluation of a 650V E-HEMT GaN Power Switch
PublicationGaN power switches have better characteristics compared to the state-of-the-art Si power transistors. These devices offer high operating temperature and current densities, fast switching and low on-resistance. However, currently only a few producers offer technology of high voltage GaN transistors. Immaturity of this technology is the reason why experimental evaluation of GaN parameters must be performed to properly exploit their...
-
Thermal and hydraulic phenomena in boundary layer of minijets impingement on curved surfaces
PublicationPresented work considers flow and thermal phenomena occurring during the single minijet impingement on curved surfaces, heated with a constant heat flux, as well as the array of minijets. Numerical analyses, based on the mass, momentum and energy conservation laws, were conducted, regarding single phase and two-phase simulations. Focus was placed on the proper model construction, in which turbulence and boundary layer modeling...
-
Application of Rapid Prototyping technology in the manufacturing of turbine blade with small diameter holes
PublicationThe article presents the possibilities of using Rapid Prototyping (RP) technology in the manufacturing of turbine blades with small diameter holes. The object under investigation was gas turbine blade with small diameter cooling holes and holes for generating longitudinal vortices. A turbine blade model was produced by means of Direct Metal Laser Sintering (DMLS) technology and subsequently validated in terms of detection and accuracy...
-
(CsX)Cu5O2(PO4)2 (X = Cl, Br, I): A Family of Cu2+ S = 1/2 Compounds with Capped-Kagomé Networks Composed of OCu4 Units
PublicationThree new salt inclusion compounds (CsX)Cu5O2(PO4)2 (X = Cl, Br, I), phosphate analogues of the kagomé mineral averievite, are reported. Their crystal structures are composed of trigonal networks of corner-sharing OCu4 anion-centered tetrahedra, forming capped-kagomé planes, which can also be regarded as two-dimensional slices along the [111] direction of a pyrochlore lattice. Magnetization and heat capacity measurements reveal...
-
WATER LUBRICATED MAIN SHAFT BEAR INGS WITH THREE LAYER BUSH – MODERN SOLUTION FOR MARINE INDUSTRY
PublicationWater lubricated sliding bearings are increasingly popular in marine and hydro power industry. Such popularity is partly due to their simple construction which also means a relatively affordable price. Properly designed and installed water lubricated bearings may well last for over a decade. During the last decade their traditional range has been expanded with new, modern products like three layer bearing bush. The work presents...
-
Tensile test of part of CuNiFeR pipeline
Open Research DataCopper and nickel alloys called cunifers (Cu, Ni, Fe and R – rest of alloy elements) have found wide application in the production of ship pipeline components in contact with sea water, such as, for example, the main engine cooling system. These alloys are characterized by a very high corrosion resistance, which is ensured by appropriately carried out...
-
Evaluation of Thermal Stresses in Asphalt Layers in Comparison with TSRST Test Results
PublicationThe paper presents the results of calculations and laboratory determination of thermal stresses at low temperatures. The modified Hills and Brien's method was used to calculate the thermal stresses in asphalt layers of pavements and the results were compared against the values obtained at a laboratory with the Thermal Stress Restrained Specimen Test (TSRST) method. The laboratory investigations were conducted using plain grade...
-
Influence of process of straightening ship hull structure made of 316L stainless steel on corrosion resistance and mechanical properties
PublicationThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries, for architectural elements, and many others. The chemical composition of corrosion-resistant...
-
An experimental investigation on the effect of new continuous core-baffle geometry on the mixed convection heat transfer in shell and coil heat exchanger
PublicationIn the article, the authors presented the influence of continuous core-baffle geometry at mixed convection heat transfer in shell and coil heat exchanger. Experiments were carried out for a large power range, i.e. from 100W to 1200W and mass flow rates ranging from 0.01 kg/s to 0.025 kg/s. During the experiments, the mass flow rate of cooling water, the temperature of water at the inlet and outlet as well as the wall temperature...
-
Cooperation of ORC installation with a gas boiler as a perspective co-generation system for households
PublicationThis paper reports tests of an innovative micro-CHP unit prototype, consisting of a traditional gas boiler and organic Rankine cycle (ORC), which incorporates original system components such as an axial vapour microturbine, evaporator and condenser. The system co-generates heat and electricity for a single household or a group of households. Electricity is only a by-product during production of heat. While testing the prototype,...
-
Computational fluid dynamics simulation of heat transfer from densely packed gold nanoparticles to isotropic media
PublicationThis work aims to determine and compare heat generation and propagation of densely packed gold nanoparticles (Au NPs) induced by a resonant laser beam (532 nm) according to the Mie theory. The heat flux propagation is transferred into the materials, which here are: silica glass; soda-lime-silica glass; borosilicate glass; polymethyl methacrylate (PMMA); polycarbonate (PC); and polydimetylosiloxane (PDMS). This analysis aims to...
-
IR-THERMAL IMAGING IN CARDIOSURGERY
PublicationA method for monitoring the state of the myocardium during cardiosurgical interventions based on thermal IR imaging is presented. These methods called Static Thermography and Active Dynamic Thermography (ADT) uses information about distribution of temperature on the surface and an external excitation source to induce thermal transient processes in a tested object. Recording time series of thermograms allows to calculate parametric...
-
A new diagnostic IR-thermal imaging method for evaluation of cardiosurgery procedures
PublicationTwo methods for monitoring the state of the myocardium during cardiosurgical interventions based on thermal IR imaging are presented below. These methods, called static thermography and active dynamic thermography (ADT), use information about the distribution of temperature on the surface, and an external excitation source to induce thermal transient processes in a tested object. Recording the time series of thermograms allows...
-
Influence of Road Wetness on Tire-Pavement Rolling Resistance
PublicationRolling resistance of tires is one of the most important factors influencing energy consumption of road vehicles, especially on rural roads. For practical reasons, most of rolling resistance measurements are usually performed for dry road conditions. Based on the fact that roads are wet during a considerable time over the year and as part of the projects MIRIAM, ROLRES and ROSANNE, the TUG (Technical University of Gdańsk) in Poland...
-
Comparison of calculated and measured thermal stresses in asphalt concrete
PublicationThe paper presents the comparison of calculated and measured thermal stresses induced in restrained asphalt concrete specimens by cooling. Thermal stresses were measured in the Thermal Stress Restrained Specimen Test. The calculations of thermal stresses were performed with the use of a theoretical formula based on the temperature dependent stiffness modulus. The novel approach applied in this paper was that the stiffness modulus...
-
Thermal, electrical, and magnetic properties of Fe2O3–PbO–SiO2 glass prepared by traditional melt-quenching and twin roller fast-cooling methods
PublicationIn this study, Fe–Pb–Si oxide glasses containing between 12.5 and 17.5 mol% Fe2O3 were prepared using two different methods comprising traditional melt-quenching and twin roller fast-cooling techniques. The topography and structure of the materials obtained were characterized by X-ray powder diffraction and scanning electron microscopy. All of the materials were found to be amorphous. The topography of most of the glasses comprised...
-
Gas selectivity enhancement by sampling-and-hold method in resistive gas sensors
PublicationCommercial resistive gas sensors exhibit various sensitivity to numerous gases when working at different elevated temperatures. That effect is due to a change in velocity of adsorption and desorption processes which can be modulated by temperature. Thus, to reach better selectivity of gas detection, we propose to apply a known method (called the sampling-and-hold method) of cooling down the gas sensor in the presence of the investigated...
-
The description of non-linear interactions of wave and non-wave modes in a non-adiabatic plasma flow
PublicationThe method of derivation of non-linear equations for interacting modes is explained and applied to a plasma's flow affected by a magnetic field. It is based on the linear projecting of the total perturbation field into specific variations of variables in individual modes of a flow. The method may be applied in many examples of fluid flows with different mechanisms of non-adiabaticity. It is of special importance in complex flows...
-
The vibration-based assessment of the influence of elevated temperature on the condition of concrete beams with pultruded GFRP reinforcement
PublicationConcrete beams reinforced with glass fiber reinforced polymer (GFRP) bars subjected to elevated temperature have been experimentally studied. The influence of high temperatures on GFRP-reinforced concrete beams condition has been check both, destructively and nondestructively. The nondestructive tests foresaw vibration-based tests to obtain the natural frequency values after exposure to varying temperatures. The vibration-based...