Filters
total: 657
Search results for: MAXIMUM EFFICIENCY
-
Overhead wires detection by FPGA real-time image processing
PublicationThe paper presents design and hardware implementation of real-time image filtering for overhead wires detection divided on image processing and results presentation blocks. The image processing block was separated from the whole implementation, and its delay and hardware complexity was analysed. Also the maximum frequency of image processing of the proposed implementation was estimated.
-
A resistivity peak close to Tc in Nd2-xCexCuO4-y single crystals.
PublicationW pracy dyskutowane jest maximum oporu elektrycznego występujące tuż powyżej temperatury przejścia nadprzewodzącego. Maksimum jest obserwowane tylko przy jednej z dwóch możliwych konfiguracji pomiarowych w metodzie van der Pauw.Proponowany, na bazie niejednorodności składu ceru, prosty model wyjaśnia w pełni pochodzenie efektu.
-
Issues of Estimating the Maximum Distributed Generation at High Wind Power Participation
PublicationThis paper presents the methods of estimating the maximum power that can be connected to the power system in distributed generation sources. Wind turbine generator systems (WTGS) were selected as the subject for analysis. Nonetheless, the considerations presented in this paper are only general and also apply to other types of power sources, including the sources that are not considered part of distributed generation.
-
Magnetic Field Generated by Short Circuit Current in the 110 kV Power System
PublicationElectric fields within tissues induced by magnetic fields including transients or short-term peaks should not be time averaged and be regarded as instantaneous values as established in the ICNIRP (International Commission on Non - Ionizing Radiation Protection) guidelines. Measurements of power lines magnetic fields with regard to human beings exposure are carried out typically with maximum current load at current balance condition...
-
Modelling Wetland Growing Season Rainfall Interception Losses Based on Maximum Canopy Storage Measurements
PublicationThis study estimates rainfall interception losses from natural wetland ecosystems based on maximum canopy storage measurements. Rainfall interception losses play an important role in water balance, which is crucial in wetlands, and has not yet been thoroughly studied in relation to this type of ecosystem. Maximum canopy storage was measured using the weight method. Based on these measurements, daily values of interception losses...
-
Broadband Compact Single-Layer Magic-T Junction with Separation of DC Signals between All Ports
PublicationA novel structure for a four-port microstrip magic-T junction is presented. The device is composed of microstrip and slotline circuits etched onto two sides of a dielectric substrate. The device is extremely compact and occupies an area more than three times smaller than similar structures recently reported in the literature. The novelty of the device lies in the use of microstrip/slotline transitions for both input ports: summation...
-
A new cold-adapted beta-D-galactosidase from the Antarctic Arthrobacter sp. 32c - gene cloning, overexpression, purification and properties
PublicationThe development of a new cold-active β-D-galactosidases and microorganisms that efficiently ferment lactose is of high biotechnological interest, particularly for lactose removal in milk and dairy products at low temperatures and for cheese whey bioremediation processes with simultaneous bio-ethanol production. In this article, we present a new β-D-galactosidase as a candidate to be applied in the above mentioned biotechnological...
-
Effect of Overloaded Vehicles on Whole Life Cycle Cost of Flexible Pavements
PublicationThe phenomenon of vehicle overloading—illegal exceeding of maximum legal weight of vehicles, is a serious problem both in developing and developed countries around the world. Overloaded vehicles occur less frequently in comparison to properly loaded vehicles but due to their greater potential to cause damage they significantly contribute to distress of pavement structure. As studies show, the number of overloaded vehicles increases...
-
Sharp bounds for the complexity of semi-equitable coloring of cubic and subcubic graphs
PublicationIn this paper we consider the complexity of semi-equitable k-coloring of the vertices of a cubic or subcubic graph. We show that, given n-vertex subcubic graph G, a semi-equitable k-coloring of G is NP-hard if s >= 7n/20 and polynomially solvable if s <= 7n/21, where s is the size of maximum color class of the coloring.
-
Chapter 4. Electricity generation from glucose microbial fuel cell
PublicationThe microbial fuel cell was constructed to generate electricity with simultaneous digestion of a glucose fuel by a bacterial biofilm. The decomposition of glucose resulted in releasing of electrons to an anode and to production of some by-products, e.g. metane or organic acids. It was found that maximum electric power density strongly depended on the proton transport through the proton exchange membrane seperating the anolyte and...
-
Thermal and Electrodynamic Risk of Residual Current Devices in the Case of Back-Up Protection by Overcurrent Circuit Breakers
PublicationResidual current operated circuit breakers without integral overcurrent protection should be back-up protected. As back-up protection devices, overcurrent circuit breakers are used. The maximum let-through energy and let-through current of the overcurrent devices were evaluated under laboratory conditions. The thermal and electrodynamic risk of residual current devices was analyzed.
-
Investigation of sensing mechanism of Nasicon electrocatalytic sensors in nitrogen dioxide and ammonia
PublicationIn this paper a sensing mechanism of Nasicon electrocatalytic sensor in nitrogen dioxide and ammonia is investigated. Both gases are environmentally hazardous and contain nitrogen atom in the molecule. However, it seems that their sensing mechanism in electrocatalytic sensor could be totally different. Namely, the maximum sensitivity for each gas was obtained at different temperatures. Also, different auxiliary layers are formed...
-
Homoclinics for singular strong force Lagrangian systems
PublicationWe study the existence of homoclinic solutions for a class of generalized Lagrangian systems in the plane, with a C1-smooth potential with a single well of infinite depth at a point ξ and a unique strict global maximum 0 at the origin.Under a strong force condition around the singular point ξ, via minimization of an action integral, we will prove the existence of at least two geometrically distinct homoclinic solutions.
-
Analytical methodologies for determination of artificial sweeteners in foodstuffs- a review
PublicationArtificial high-intensity sweeteners are more and more frequently used for food production. Food industry tends to highlight beneficial aspects of their use, such as tooth-friendliness, rising-up quality of life of those suffering from different forms of diabetes and possibility of weight control without sacrificing favorite unhealthy drinks or snacks. On the other hand some of the consumers are deeply concerned about safety of...
-
Evaluation of the Influence of Farming Practices and Land Use on Groundwater Resources in a Coastal Multi-Aquifer System in Puck Region (Northern Poland)
PublicationThis study focuses on the modeling of groundwater flow and nitrate transport in a multi-aquifer hydrosystem in northern Poland, adjacent to Puck Bay (Baltic sea). The main goal was to investigate how changes in land use and farming practices may affect groundwater recharge and submarine groundwater discharge (SGD) to the sea and the associated N-NO3 fluxes. An integrated modelling approach has been developed, which couples the...
-
Computational fluid dynamics simulation of heat transfer from densely packed gold nanoparticles to isotropic media
PublicationThis work aims to determine and compare heat generation and propagation of densely packed gold nanoparticles (Au NPs) induced by a resonant laser beam (532 nm) according to the Mie theory. The heat flux propagation is transferred into the materials, which here are: silica glass; soda-lime-silica glass; borosilicate glass; polymethyl methacrylate (PMMA); polycarbonate (PC); and polydimetylosiloxane (PDMS). This analysis aims to...
-
Cyclic behavior of FeCoCrNiMn high entropy alloy coatings produced through cold spray
PublicationeCoCrNiMn high entropy alloy powders were employed to produce coatings on carbon steel through high pressure cold spray (at 1100 °C and 7 MPa in temperature and pressure respectively). X-ray diffraction of the sprayed material revealed a dense coating with the retention of the original crystallographic structure. Once splatted, particles revealed high flattening ratio with consequent excellent adhesion of the coating to the substrate....
-
Lateral load resistance of piled raft foundation - A case study of District Jail, Saidu Sharif, Swat Pakistan
PublicationPiled raft foundations under lateral loads are usually designed as a pile group, ignoring the contribution of the raft to resisting the lateral loads. In this paper, a case study was performed to determine the raft's contribution to the lateral load resistance. This study analyzed a pile-supported reinforced concrete retaining wall for two different foundation conditions, i.e., pile group foundation and pile raft foundation. Pile group...
-
LCF behavior of 2024AA under uni- and biaxial loading taking into account creep pre-deformation
PublicationThis study presents the results of experimental low-cycle fatigue (LCF) tests of aluminum 2024 alloy T3511 temper in uni- and biaxial loading states. Tests were carried out on both the as-received material (hardened extruded rods) and material with different pre-deformation histories. These deformations were carried out in the creep process at 200 °C and 300 °C for two different levels of at each temperature. The pre-deformed material’s...
-
Homoclinic orbits for a class of singular second order Hamiltonian systems in ℝ3
PublicationWe consider a conservative second order Hamiltonian system \ddot{q}+ ∇V(q)=0 in R3 with a potential V having a global maximum at the origin and a line l ∩ {0} = ∅ as a set of singular points. Under a certain compactness condition on V at infinity and a strong force condition at singular points we study, by the use of variational methods and geometrical arguments, the existence of homoclinic solutions of the system.
-
CPLFD-GDPT5: High-resolution gridded daily precipitation and temperature data set for two largest Polish river basins
PublicationThe CHASE-PL (Climate change impact assessment for selected sectors in Poland) Forcing Data–Gridded Daily Precipitation & Temperature Dataset–5 km (CPLFD-GDPT5) consists of 1951–2013 daily minimum and maximum air temperatures and precipitation totals interpolated onto a 5 km grid based on daily meteorological observations from the Institute of Meteorology and Water Management (IMGW-PIB; Polish stations), Deutscher Wetterdienst...
-
Two families of infinitely many homoclinics for singular strong force Hamiltonian systems
PublicationWe are concerned with a planar autonomous Hamiltonian system with a potential possessing a single well of infinite depth at a point X and a unique strict global maximum 0 at a point A. Under a strong force condition around the singularity X, via minimization of an action integral and using a shadowing chain lemma together with simple geometrical arguments, we prove the existence of infinitely many geometrically distinct homoclinic...
-
Metrological analysis of precision of the system of delivering a water capsule for explosive production of water aerosol
PublicationIn this paper an analysis of precision of the system controlling delivery by a helicopter of water-capsule designed for extinguishing large scale fires is presented. The analysis was performed using the numerical method of distribution propagation (Monte Carlo method) supplemented with results of application of the uncertainty propagation method. In addition the optimum conditions for the airdrop are determined to ensure achievement...
-
Sizes of iron hydroxide particles formed during ferric coagulation processes
PublicationThe aim of the study was to apply laser granulometer for measuring sizes of particles formed in iron-based coagulation process in water, which did not contain significant amounts of organic compounds. The research was conducted using tap water, obtained from underground sources. Iron sulfate in doses of 2.0–10.0 mgFe L–1 was added to water. During initial stage of flocculation, iron hydroxide particles reached dimensions between...
-
NEW SOLUTIONS FOR THE SOLAR CHARGE CONTROLLERS DESIGN FOR OBTAINING TRUE MPP IN PARTLY SHADED PV MODULES
PublicationSoft shading sources such as tree limbs, structural elements of buildings and chimneys, scatter and refract sunlight, significantly reducing the amount of radiation reaching the surface of the module. The hard shadings located directly on the surface (i.e. bird droppings, leaves, snow) tend to stop sunlight completely. These phenomena significantly affects the output characteristics of photovoltaic modules and often contribute...
-
Postquarter-Point Case of Ship’s Side-Berthing and Its Influence on Marine Fender Pitch
PublicationThis paper presents a critical analysis of some selected codes and practical recommendations used as basic rules in the design procedures of modern marine fender systems. The first part of the discussion pertains to the existing equations used in calculating the eccentricity coefficient in the ship’s kinetic energy equation and the maximum allowable fender pitch (spacing) in a set of fenders installed along a quay wall. A new approach...
-
Feedline Alterations for Optimization-Based Design of Compact Super-Wideband MIMO Antennas in Parallel Configuration
PublicationThis letter presents a technique for size reduction of wideband multiple-input-multiple-output (MIMO) antennas. Our approach is a two-stage procedure. At the first stage, the antenna structure is modified to improve its impedance matching. This is achieved through incorporation of an n-section tapered feedline, followed by reoptimization of geometry parameters. Reducing the maximum in-band reflection well beyond the acceptance...
-
Ice Load Characteristics on Floating Photovoltaic Platform
PublicationNowadays, based upon human needs and preferring perpetual types of energy, photovoltaic system (PV) is a suitable alternative and more frequently used in northern countries, which are recently more attracted by solar power. The new floating type of the structure is installed in the water bodies instead of land. One of the main elements in floating photovoltaic structures is the forces imposed on the panels. In the northern regions,...
-
Electrochemical capacitor temperature fluctuations during charging/discharging processes
PublicationThepaperpresentsaproposalofusingadditionalstatisticalparameterssuchas:standarddeviation,variance, maximum and minimum increases of the observed value that were determined during measurements of temperature fields created on the surface of the tested electrochemical capacitor. The measurements were carriedoutusingthermographicmethodsinordertosupportassessmentoftheconditionofelectrochemical capacitorunderclassicdurabilitytestsbasedonmethodsofdeterminationofcapacityandequivalentseries...
-
Independence in uniform linear triangle-free hypergraphs
PublicationThe independence number a(H) of a hypergraph H is the maximum cardinality of a set of vertices of H that does not contain an edge of H. Generalizing Shearer’s classical lower bound on the independence number of triangle-free graphs Shearer (1991), and considerably improving recent results of Li and Zang (2006) and Chishti et al. (2014), we show a new lower bound for a(H) for an r-uniform linear triangle-free hypergraph H with r>=2.
-
Measurement of the Temporal and Spatial Temperature Distribution on the Surface of PVCP Tissue Phantom Illuminated by Laser Dataset
PublicationThe dataset entitled Measurement of the temporal and spatial temperature distribution on the surface of PVCP tissue phantom illuminated by laser was obtained with a laboratory set-up for characterisation of the thermal properties of optical tissue phantoms during laser irradiation. The dataset contains a single image file representing the spatial temperature distribution on the surface of a PVCP tissue phantom. This thermal image...
-
Experimental investigation on heat pipes supported by soy wax and lauric acid for electronics cooling
PublicationThis paper presents an experimental study of heat pipes for electronics cooling that were supported by energy storage materials (i.e. phase change materials - PCMs) coated at the adiabatic section. The PCMs utilized included two materials, namely lauric acid and soy wax, the latter being considered as a more cost-effective alternative. The study focused on three different powers: 20 W, 25 W, and 30 W. Both heating, cooling, and...
-
Bending Moment Control and Weight Optimization in Space Structures by Adding Extra Members in the Optimal Locations
PublicationThis paper investigates the reduction of bending moment in critical members by adding some extra members in the optimum location. Instead of enlarging the size of members to resist the moment, eight additional members are added in the optimum location to reduce the bending moment in the critical members. The total weight of the proposed structure with extra members is less than that of the original structure that resists the induced...
-
Toxicity and chemical analyses of airport runoff waters in Poland
PublicationThe aim of this study was to assess the ecotoxicological effects of various compounds in complex airport effluents using a chemical and ecotoxicological integrated strategy. The present work deals with the determination of sum of PCBs, PAHs, pesticides, cations, anions, phenols, anionic, cationic, non-ionic detergents, formaldehyde and metals – as well as TOC and conductivity – in runoff water samples collected from 2009 to 2011...
-
GreedyMAX-type Algorithms for the Maximum Independent Set Problem
PublicationA maximum independent set problem for a simple graph G = (V,E) is to find the largest subset of pairwise nonadjacent vertices. The problem is known to be NP-hard and it is also hard to approximate. Within this article we introduce a non-negative integer valued functionp defined on the vertex set V(G) and called a potential function of agraph G, while P(G) = max{vinV(G)| p(v)} is called a potential of G. For any graph P(G) <= D(G),...
-
In vivo performance of intraperitoneal onlay mesh after ventral hernia repair
PublicationBackground: Ventral hernia repair needs to be improved since recurrence, postoperative pain and other complications are still reported in many patients. The behavior of implants in vivo is not sufficiently understood to design a surgical mesh mechanically compatible with the human abdominal wall. Methods: This analysis was based on radiological pictures of patients who underwent laparoscopic ventral hernia repair. The pictures...
-
Design of Structure of Tension Leg Platform for 6 MW Offshore Wind Turbine Based On Fem Analysis
PublicationThe article presents the calculation and design stages of the TLP platform serving as a supporting construction of a 6 MW offshore wind turbine. This platform is designed to anchor at sea at a depth of 60 m. The authors presented the method of parameterization and optimization of the hull geometry. For the two selected geometry variants, the load and motion calculations of the platform subjected to wind, wave and current under...
-
Tensile validation tests with failure criteria comparison for various GFRP laminates
PublicationThe paper studies the mechanical properties of glass fibre reinforced polymers (GFRP) with various types and orientation of reinforcement. Analyzed specimens manufactured in the infusion process are made of polymer vinyl ester resin reinforced with glass fibres. Several samples were examined containing different plies and various fibres orientation [0, 90] or [+45, –45]. To assess the mechanical parameters of laminates, a series...
-
Effects of Noncontact Shoulder Tool Velocities on Friction Stir Joining of Polyamide 6 (PA6)
PublicationIn this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the...
-
Position and velocity measurement using incremental encoder and microcontroller.
PublicationThere is presented measurement of position and velocity using Atmel's microcontroller ATTiny2313 with 20 MHz clock and encoder with 1024 pulses per revolution. This configuration allows measuring maximum speed 48800 rpm with 1x accuracy, 20200 rpm with 2x accuracy and 9400 rpm with 4x accuracy (quadrature). Position is measured with resolution of 0.352', 0.176' and 0.088' for 1x, 2x, 4x accuracy respectively. Algorithms of position...
-
Differential-algebraic systems with maxima
PublicationMetoda numeryczno-analityczna została zastosowana do układów równań różniczkowo-algebraicznych z operatorem maximum. Zakładając warunek Lipschitza na funkcje występujące w zagadnieniu pokazano, że ciąg iteracji prostych jest zbieżny do rozwiązania zagadnienia pomocniczego. Podano warunki dostateczne na istnienie rozwiązania problemu wyjściowego. Iteracje Seidla też były przedmiotem badań. W ostatniej części pracy był dyskutowany...
-
A simple approach to heat exchanger sizing optimisation by means of entrophy generation minimisation
PublicationIn the paper an attempt is presented to find the method of optimization of microtube diameter with respect to optimal thermal-hydraulic conditions in the single-phase shell-and-tube heat exchangers. The approach is based on consideration of pumping power at the condition of maximum heat transfer by the heat exchanger tube system. In the optimization method the tube diameter is first specified and then appropriate calculations are...
-
Impact of maintenance of floodplains of the Vistula River on high water levels on the section from Włocławek to Toruń
PublicationThis article describes the methodology of hydraulic calculations to estimate the water levels in open channels for steady gradually varied flow. The presented method has been used to analyse the water level on the Vistula River from Włocławek cross-section to Toruń cross-section. The HEC-RAS modelling system has been used for parameterization of the river channel and floodplains, as well as for flow simulation. The results obtained...
-
Biomechanics of the front abdominal wall as a potential factorleading to recurrence with laparoscopic ventral hernia repair
PublicationThis study investigated the front abdominal wallto describe its elasticity in vivo and searched for elongationsthat possibly stretched an implanted mesh, therebycausing fixation failure and subsequent recurrence.To measure front abdominal wall elongations, amodel of fascia movements was created. Eight healthyvolunteers were measured during exercise to determine theextent of elongations in their front abdominal wall. Videoswere...
-
Weldability of S460ML High Strength Low Alloy Steel in Underwater Conditions
PublicationThe paper presents experimental evaluation of susceptibility of the high strength S460ML steel to cold cracking in the conditions of wet welding with the use of covered electrodes. From the results of Tekken tests it was found out that the investigated steel was characterised, in the conditions of the carried out experiments (underwater wet welding and air welding with rutile electrodes), of high susceptibility to cold cracking....
-
Study of the influence of thermal factors on the welding process of polyethylene gas pipelines,
PublicationA one-dimensional calculation scheme is proposed with the help of which it is possible to determine and set the technological parameters with the accuracy to be realized in production conditions: the temperature of the heating element and the heating time, which allows maximum mechanization of the technological operations of polyethylene gas pipelines welding. The numerical value of the coefficient of temperature for polyethylene...
-
From a Point Cloud to a 3D Model - an Exercise for Users of AutoCAD and Revit
PublicationThe paper presents a proposal of the topic of an exercise for students of building faculties as part of classes on 3D modelling. The task consists in creating a three-dimensional model based on the measurement obtained with the Leica P30 laser scanner. Due to the maximum number of points in the cloud in the presented programs, the output files must be properly cleared and reduced. The point cloud was pre-processed in Cyclone software....
-
Robustified estimators of radar elevation angle using a specular multipath model
PublicationWe consider the problem of estimating the elevation angle in the presence of multipath. The proposed method belongs to the class of maximum likelihood-like estimators and employs a modified specular reflection model that accounts for the uncertainty of the steering vector by assuming that they are subject to unknown deterministic perturbations with bounded norms. The analysis, performed using convex optimization methods, allows...
-
The protocol for using elastic wall model in modeling blood flow within human artery
PublicationMedical diagnostic tools will play a major role in the future for an effective patient treatment and reduction their mortality, related to the cardiovascular system diseases (CVDs). There is an urgent need for developing diagnostic procedure to be robust, reliable, accurate and efficient, in the framework of a paradigm shift. Application of numerical techniques is seen as a perspective tool for such purpose. Nevertheless, existing...
-
Influence of the Addition of Recycled Aggregates and Polymer Fibers on the Properties of Pervious Concrete
PublicationThe aim of the study was to check the possibility of reusing aggregate from recycled concrete waste and rubber granules from car tires as partial substitution of natural aggregate. The main objective was to investigate the effects of recycled waste aggregate modified with polymer fibers on the compressive and flexural strength, modulus of elasticity and permeability of pervious concrete. Fibers with a multifilament structure and...