Search
Search results for: DRUM-BUFFER-ROPE
-
Determination of the Bending Properties of Wire Rope Used in Cable Barrier Systems
PublicationThis paper presents research on the bending properties of 3 × 7 19-mm wire rope commonly used in road cable barriers. A total of 19 experimental tests were conducted. In addition, two nonlinear 3D numerical models of the wire rope using beam and solid finite elements were developed. Based on these models, four numerical simulations were carried out. The numerical results were validated against the experimental ones and a very good...
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublicationTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
Influence of the jitter buffer on the quality of service VoIP.
PublicationVoIP (Voice over IP) is a modern service with enormous potential for yet further growth. It uses the already available and universally implemented IP transport platform. One significant problem, however, is ensuring the Quality of Service, abbreviated QoS. This paper addresses exactly that issue. In an extensive investigation the influence of jitter buffers on QoS is being examined in depth. Two implementations, namely a passive...
-
Drum Replacement Using Wavelet Filtering Podmienianie próbek perkusyjnych przy zastosowaniu filtracji falkowej .
PublicationThe paper presents the solution that can be used to unify snare drum sound within a chosen fragment. The algorithm is based on the wavelet transformation and allows replacement of sub-bands of particular sounds, which are outside a certain range. Five experienced sound engineers put the algorithm under the test using samples of five different snare drums. Wavelet filtering seems to be useful in terms of drum replacement, while...
-
Temperature influence on tire/road noise evaluated by the drum method
PublicationAmbient air and road surface temperatures substantially affect the road vehicle noise emission. The temperature influence on tire/road noise depends mainly on tire-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tires. The correction procedures for temperature effect are still under consideration and preparation. Laboratory experiment was prepared to...
-
Drum Replacement Using Wavelet Filtering Podmienianie próbek perkusyjnych przy zastosowaniu filtracji falkowej
PublicationThe paper presents the solution that can be used to unify snare drum sound within a chosen fragment. The algorithm is based on the wavelet transformation and allows replacement of sub-bands of particular sounds, which are outside a certain range. Five experienced sound engineers put the algorithm under the test using
-
Compensation of Voltage Drops in Trolleybus Supply System Using Battery-Based Buffer Station
PublicationThis paper analyzes the results of a trial operation of a battery-based buffer station supporting a selected section of trolleybus power supply systems in Pilsen, Czech Republic. The buffer station aims to prevent the catenary from excessive voltage drops in a part of the route that is most remote from the traction substation. Compensation of voltage drops is carried out by continuously measuring the catenary voltage and injecting...
-
The analysis of the system towing rope with long underwater object
PublicationW artykule zawarta jest analiza zestawu złożonego z liny holującej i długiego obiektu podwodnego o małej sprężystości.Sformułowane zagadnienie brzegowe rozwiązywane jest iteracyjnie z zastosowaniem metody elementów skończonych. Z warunków brzegowych znany jest punkt zaczepienia liny holującej na okręcie oraz głębokość na jaką zanurza się koniec holowanego obiektu. Rozwiązanie tego zagadnienia doprowadziło do równań źle uwarunkowanych...
-
Classification of Music Genres Based on Music Separation into Harmonic and Drum Components . Klasyfikacja gatunków muzycznych wykorzystująca separację instrumentów muzycznych
PublicationThis article presents a study on music genre classification based on music separation into harmonic and drum components. For this purpose, audio signal separation is executed to extend the overall vector of parameters by new descriptors extracted from harmonic and/or drum music content. The study is performed using the ISMIS database of music files represented by vectors of parameters containing music features. The Support Vector...
-
Ladder-Based Synthesis and Design of Low-Frequency Buffer-Based CMOS Filters
PublicationBuffer-based CMOS filters are maximally simplified circuits containing as few transistors as possible. Their applications, among others, include nano to micro watt biomedical sensors that process physiological signals of frequencies from 0.01 Hz to about 3 kHz. The order of a buffer-based filter is not greater than two. Hence, to obtain higher-order filters, a cascade of second-order filters is constructed. In this paper, a more...
-
Unity-Gain Zero-Offset CMOS Buffer with Improved Feedforward Path
PublicationA voltage unity-gain zero-offset CMOS amplifier with reduced gain error and increased PSRR (power supply rejection ratio) is proposed. The amplifier uses two feed mechanisms, negative feedback and supporting positive feedforward, to achieve low deviation from unit gain over the entire input range. The circuit, designed in a standard 180-nanometer 1.8-voltage CMOS process, is compared with two known buffers of similar topology,...
-
ANALYSIS OF ROLLING RESISTANCE OF TIRES WITH RUN FLAT INSERT APPLYING DRUM METHOD AND RADIAL CHARACTERISTIC
PublicationThis paper presents analysis of rolling resistance of tires with RUN FLAT insert applying drum method and radial characteristic. The conducted studies indicated changes in operational properties of wheel, occurring as a result of inflation pressure drop in the wheel. As regards radial elasticity, such changes result in significant drop of radial rigidity and increase of static deflection and increase of tire rolling resistance....
-
3D Form analysis of rope deformation with long towed underwater hydroacoustic antenna
PublicationArtykuł opisuje rozwiązanie zagadnienia brzegowego dla zestawu długiej liny holującej i podwodnej anteny hydroakustycznej o gęstości, tej ostatniej, nieznacznie większej od gęstości wody i małej sztywności. Znane jest tylko położenie punktu zamocowania liny do okrętu (p-kt początkowy holowanego zestawu) oraz głębokość, na której znajduje się koniec anteny. Przedstawiono analizę sił działających na holowany zestaw, ich równania...
-
Instantaneous impedance monitoring of AA 7075 aluminum alloy corrosion in borate buffer with admixed chloride ions
PublicationThe study presents a research capabilities of Dynamic Electrochemical Impedance Spectroscopy (DEIS) as a tool used for instantaneous on-line monitoring of corrosion processes on the example of AA 7075 aluminum alloy. A borate buffer with admixed chloride ions in a quantity ranging from 0.05 to 25 mM was used to represent different types of corrosion attack. The surface of samples specimens was evaluated before and after the tests...
-
Beyond the helium buffer: 12C−2 rotational cooling in cold traps with H2 as a partner gas: interaction forces and quantum dynamics
Publicationabstract = { The scattering cross-sections and corresponding rate coefficients for rotationally inelastic collisions of $^{12}$C$_2$^-$ ($^2 \Sigma_g^+$) with H$_2$ ($^1 \Sigma_g^+$) are presented over a broad range of cold-trap temperatures. They have been calculated using quantum scattering theory that employs a new ab initio potential energy surface. The rate coefficients for the inelastic processes in the anionic partner are...
-
Pitting corrosion and stress-corrosion cracking of buffer tanks in a brewery
PublicationW pracy przedstawiono wyniki ekspertyzy zbiornika magazynowego na ciepłą wodę do produkcji piwa w browarze. Zbiornik uległ przyśpieszonym procesom korozyjnym, które doprowadziły do jego perforacji. Podczas eksploatacji zbiornika wystąpił proces korozji wżerowej oraz pękania korozyjnego. Przyśpieszone procesy korozyjne zbiornika związane były z wysoką zawartością jonów chlorkowych w wodzie oraz statycznymi naprężeniami mechanicznymi....
-
Investigation of thin perovskite layers between cathode and doped ceria used as buffer layer in solid oxide fuel cells
PublicationIn this paper, thin perovskite layers between cathode material of solid oxide fuel cells and gadolinia-doped ceria buffer layer are investigated. Thin layers made of LaNi0.6Fe0.4O3-δ (LNF), La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF), or SrTi0.65Fe0.35O3-δ (STF) were symmetrically deposited by spin coating method from metallo-organic polymer precursors on a Ce0.8Gd0.2O2-δ (CGO) substrate. Porous and about 40-μm-thick LNF cathodes were deposited...
-
A versatile analog CMOS cell: voltage - buffer /current - conveyor/ multiplier
PublicationW pracy przedstawiono koncepcję uniwersalnej komórki analogowej przeznaczonej dla programowalnych układów analogowych (FPAA). Komórka może pełnić funkcję bufora napięciowego, konwjora prądowego lub mnożnika analogowego. Układ przesymulowano w technologii CMOS 2 ćm.
-
Effect of Sieve Drum Inclination Angle on Wheat Grain Cleaning in a Novel Rotary Cleaning Device
Publication -
Two-photon induced fluorescence of Cy5-DNA in buffer solution and on silver island film
PublicationOpisano fluorescencję barwnika CY5 połączonego z DNA w roztworze buforowym na wysepkach srebrowych.
-
Cyclic analysis of thermal impedance of a passive layer of aluminium in a neutral borate buffer solution
PublicationW pracy przedstawiono wyniki badań warstwy pasywnej tworzącej się na stopie 1050 A w warunkach zmieniającej się temperatury. Zmiany realizowano w sposób cykliczny zwiększając a następnie zmniejszając temperaturę. W czasie zmian temperatury prowadzono badania metodę dynamicznej elektrochemicznej spektroskopii impedancyjnej. Stwierdzono największe zmiany parametrów elektrycznego schematu zastępczego w czasie pierwszego cyklu zmian....
-
Preparation of DNA films for studies under vacuum conditions. The influence of cations in buffer solutions
PublicationBadania zostały przeprowadzone w celu określenia optymalnych warunków wymaganych do przygotowania jednolitych filmów superskręconego plazmidowego DNA do wykorzystania w doświadczeniach napromieniowania w warunkach wysokiej próżni. Badania pokazują, że znaczne szkody w DNA powstają w wyniku odpompowywania filmów DNA z roztworów zawierających jedynie czysta wodę.
-
Effect of buffer layers on performance of organic photovoltaic devices based on copper phthalocyanine-perylene dye heterojunction
PublicationPraca przedstawia wyniki badań układu fotowoltaicznego złożonego z cienkich warstw organicznych tworzących złącze (CuPc i MePTCDI), elektrod (ITO i Ag) oraz z warstw buforowych (MoO3 przy ITO i BCP przy Ag).
-
Application of multistage treatment wetlands as a buffer for effluent from Anammox treatment for reject water from centrifugation
PublicationAccording to the newest knowledge concerning TW technology multistage treatment wetland could be easily applied for ensuring stable and low concentration of biogenic compounds form the effluent of SBR reactor (with nitritation/annamox process) for treatment of digested sludge dewatering in side stream. The working condition and optimising of such MTW will be the issue of carried out investigation.
-
Buffer contribution to formation enthalpy of copper(II)–bicine complex determined by isothermal titration calorimetry method
Publication -
Application of Vertical Reed Beds as a Buffer for Effluent from SBR ANAMMOX Treatment for Reject Water from Centrifugation
PublicationThe main purpose of this study is to determine the removal efficiency of nitrogen compounds in the effluentfrom ANAMMOX process used to treat reject water after centrifugation. A pilot model was bulit consisting of fourdifferent Treatment Wetlands beds with different filter substrate and with or without macrophytes growth. Verticalsubsurface flow type filters have been choosen thanks to their highest efficiency in NH4-N removal...
-
Separation of nicotinic acid and its structural isomers using 1-ethyl-3-methylimidazolium ionic liquid as a buffer additive by capillary electrophoresis
Publication -
The combined effect of moderate pressure and chitosan on Escherichia coli and Staphylococcus aureus cells suspended in a buffer and on natural microflora of apple juice and minced pork
PublicationW pracy określono przeżywalność bakterii Escherichia coli i Staphylococcus aureus oraz naturalnej mikroflory soku jabłkowego i rozdrobnionego mięsa świńskiego po działaniu ciśnienia 193 MPa w temp. -20 C w obecności chitozanu. Stwierdzono, że traktowanie mikroorganizmów ciśnieniem w obecności chitozanu pozwala na przedłużenie trwałości badanych produktów przechowywanych w temperaturze chłodniczej o około 8-10 dni.
-
Marek Adamowicz dr hab. inż.
PeopleStopień naukowy doktora uzyskał w 2008 r. na Wydziale Elektrotechniki i Automatyki Politechniki Gdańskiej. W latach 2005 – 2011 pracował na Akademii Morskiej w Gdyni. W 2010 r. jako laureat programu NCBR LIDER wybrał Wydział Elektrotechniki i Automatyki Politechniki Gdańskiej jako jednostkę realizującą swój projekt z zakresu szerokopasmowych przyrządów półprzewodnikowych i ich zastosowań w elektrowniach wiatrowych. Od 2011 roku...
-
Consideration of the safety of bungee jumping in relation to mechanical properties of the instalation based on a jump accident in Gdynia
PublicationThis paper considers a bungee jumping accident that took place in July 2019 in Gdynia, Poland. The authors conducted an investigation to determine the cause of the bungee rope failure. It was based on mechanical tests concerning the strength of the rope as well as the calculation of the force induced in the rope during the jump. Based on the theoretical and experimental results, the rope safety factor was estimated. It appeared...
-
Factors determining selection of production planning and control system
PublicationThe article contains a comparative characteristics of selected systems of production planning and control, such as: MRP, kanban/JiT, DBR/TOC. The results of the performed analyses served as a basis for determining key market factors related to production planning and control functions, which determine the choice of an appropriate system.
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublicationTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
Comparison of road and laboratory measurements of tyre/road noise
PublicationTyre/road noise is one of the major environmental problems related to road traffic. There are several measuring methods of tyre/road noise that may be carried out on the road (for example Coast-down and Close Proximity Method) or in the laboratory (Drum Method). Road measurements are preferred for evaluations of pavement properties while laboratory methods are mostly used to evaluate tyres. One of the biggest problems associated...
-
The microstructure of AA5754 alloy under corrosion in alkaline media (pH=11) with 20 mM of various carboxylic acids
Open Research DataThis dataset contains scanning electron microscopy (SEM) micrographs taken for polished aluminum AA5754 alloy samples, exposed for 100 min in bicarbonate buffer (pH=11) with the addition of 20 mM of carboxylic acids, namely: citric acid, malic acid, maleic acid, succinic acid, tartaric acid, tricarballylic acid and serine. The goal of this study was...
-
The microstructure of AA5754 alloy under corrosion in alkaline media (pH=11) with 4.5 mM of various carboxylic acids
Open Research DataThis dataset contains scanning electron microscopy (SEM) micrographs taken for polished aluminum AA5754 alloy samples, exposed for 100 min in bicarbonate buffer (pH=11) with the addition of 4.5 mM of carboxylic acids, namely: citric acid, malic acid, maleic acid, succinic acid, tartaric acid, tricarballylic acid and serine. The goal of this study was...
-
SEM micrographs of aluminium corrosion in alkaline media with various bee products as corrosion inhibitors
Open Research DataThis dataset contains various scanning electron microscopy (SEM) micrographs of AA5754 aluminum alloy samples exposed to the corrosive alkaline environment without and with the addition of various bee products to act as green corrosion inhibitors. The products are bee pollen, honey, and putty. They were investigated in bicarbonate buffer (pH =10 or...
-
Impact of the surface evenness and texture on tire/road rolling resistance
PublicationThis paper deals with the issue of a surface's roughness and texture impact on tire/road rolling resistance. It includes a brief description of research aims, measurements and an analysis of results. It also presents observations and conclusions regarding drum facility modernisation which allows studies concerning surface's roughness and texture impact on tire/road rolling resistance.
-
Analysis of start energy of Stirling engine type alpha
PublicationThe Stirling engine type alpha is composed of two cylinders (expansion space E and compression space C), regenerator that forms the space between the cylinders and the buffer space (under the pistons). Before the start-up and as a result of long-term operation, the average pressure in the working space (above the pistons) and in the buffer space is the same. However, in the initial phase of operation, the average pressure in the...
-
Photoelectric properties of a novel MEH-PPV/F16ZnPc heterojunction
PublicationPhotoelectric properties of a novel poly[2-methoxy-5-(2-ethylhexyloxy-p-phenylenevinylen)] (MEH-PPV)/perfluorozincphthalocyanine (F16ZnPc) planar heterojunction provided with BCP and MoO3 buffer layers sandwiched between indium tin oxide (ITO) and Ag are shown. Efficient photogeneration of charge carriers at this junction is observed. Effect of bathocuproine (BCP) and MoO3 buffer layers on the performance of cells is analysed....
-
Tyre/road noise reduction of poroelastic road surface tested in a laboratory
PublicationA so-called poroelastic road surface (PERS) is being developed in Europe. This contains a large percentage of rubber particles mixed with hard aggregate (stone and sand) and bound with polyurethane. This gives high air void content (around 30 %), high elasticity and smooth texture, all of which should give low noise properties. Inthis experiment anominally 30 mm thick sample of PERS was mounted on a steel drum. Various car tyres...
-
IKE1-IKE3 (C-1305 derivatives) inhibitory effect of the Yeast Topoisomerase II relaxation activity
Open Research DataInhibition of Yeast Topoisomerase II were analyzed according to relaxation assay kit from Inspiralis. Briefly, 250 ng of supercoiled pBR322 DNA, 1 mM ATP, 1-200 μM of analyzed compound were mixed with reaction buffer (1 mM Tris-HCl (pH 7.9), 10 mM KCl, 0.5 mM MgCl 2, 0.2 % (v/v) glycerol). The reaction was initiated by the addition of an enzyme, allowed...
-
Tire camber angle influence on tire-pavement noise
PublicationTaking into account tire-pavement noise and tires classification with respect to noise emission special measurement methods are usually used. When two of them are applied (the Laboratory Drum Method (DR) and the Close-Proximity Method (CPX)) the investigator has to be sure that the position of the tire is correct. The authors of this paper thought about tire position as tire (wheel) alignment in particular tire camber angle. They...
-
Method of estimating the rolling resistance coefficient of vehicle tyre using the roller dynamometer
PublicationThe tendency in the past few years has been to introduce tyres with lower rolling resistance coefficients to the market. This paper presents a mathematical method for determining the rolling resistance coefficients variation depending on the speed. The method uses power balance which results from automobile dynamics while rolling on chassis dynamometer. The rolling resistance coefficients of tyres obtained through ‘drum test method’,...
-
Interaction of SrTi0.65Fe0.35O3-δ with LaNi0.6Fe0.4O3-δ, La0.6Sr0.4Co0.2Fe0.8O3-δ and Ce0.8Gd0.2O2-δ
PublicationIron doped strontium titanates SrTi1-xFexO3-δ are perovskites of versatile properties. They can be used in solid oxide fuel cells or high temperature oxygen sensors. Their reactivity with electrolyte materials, cathode buffer layer materials, other cathode materials or current collector layers has not been fully tested. In this study we use X-ray diffraction to check SrTi0.65Fe0.35O3-δ compatibility with Ce0.8Gd0.2O2-δ (used as...
-
A method to determine the tightening sequence for standing rigging of a mast
PublicationThe article proposes an alternative method to determine the sequence of generation of pre-tension forces in standing rigging of a mast. The proposed approach has been verified on both a virtual simulation experiment and laboratory tests. In this method, the desired tension values are obtained using the influence matrix which allows to calculate the effect of tension change in an individual rope on the tension distribution in the...
-
A 3D-FEM mesh technique for fast analysis of waveguide problems containing rotatable tuning elements
PublicationIn this paper a meshing technique for 3D Finite Element Method is presented. It allows for fast analysis and optimization of the waveguide structures, which contain rotatable tuning elements. In the proposed procedure a thin layer of varying cylindrical mesh buffer is introduced in order to reuse unchanged mesh and FEM matrices in the rest of the domain.
-
The electrochemical determination of isatin at nanocrystalline boron-doped diamond electrodes: stress monitoring of animals
PublicationUltra-thin nanocrystalline boron-doped diamond electrodes (B:NCD) were used for the electrochemical determination of isatin in dog urine samples using cyclic voltammetry and square wave voltammetry in a phosphate buffer saline, pH = 7.2. No additional modification or pretreatment of the electrode surface was required in this approach, being of high importance for the facile detection procedure. The increase of the peak current...
-
Wytrzymałość pętli wplatanych na linach podwójnie plecionych
PublicationCechą wyróżniającą statki żaglowe z grona innych obiektów pływających są żagle. To cecha widoczna, za którą kryją się mniej romantyczne elementy, takie jak maszty, liny i osprzęt. Rozpostarcie białych płócien na maszcie i następnie żeglowanie wymaga sprawnego operowania nimi, co wiąże się z doborem odpowiedniego ich zestawu, ułożenia i napięcia. To maszty są kręgosłupem takielunku, a liny jego mięśniami i ścięgnami. Do poprawnego...
-
Wpływ kąta pochylenia koła na opór toczenia opon samochodowych
PublicationW pracy przedstawiono wpływ kąta pochylenia koła na opór toczenia opon do samochodów osobowych. Pomiary oporu toczenia kół toczących się z kątem pochylenia od -6º do +3º wykonano na bębnowej maszynie bieżnej metodą momentową. Wyniki pomiarów przedstawiono w formie zależności współczynnika oporu toczenia oraz przyrostu współczynnika oporu toczenia w funkcji kąta pochylenia badanego koła.
-
Morphological and electrochemical characterization of ceramic carbon foam electrodes water treatment applications
Open Research DataThis dataset contains morphological and electrochemical characterization of ceramic carbon foam employed as an electrode (CFFE) for the oxidation of a target pollutant. The dataset includes: