Search
Filters
total: 46
Search results for: work hardening
-
Relationship between cavitation resistance of laser produced alloys and their ability to work hardening
PublicationBadano odporność kawitacyjną laserowo wytworzonych stopów na stalach konstrukcyjnych i ich związek ze zdolnością do umacniania się pod wpływem działania obciążeń kawitacyjnych. Wykazano, że mikrotwardość powierzchni wykazuje monotoniczną zależność z odpornością kawitacyjną i zdolnością do umacniania.
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublicationThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
SEM examination of surface layer of C45 steel after grinding on defferent depth
Open Research DataFerrite examination for the medium carbon structural steel with low content of Mn, Si, Cu, Cr and Ni after its grinding to a depth of 2 µm, 8 µm, 14 µm and 20 µm, at constant wheel circumferential speed of vs = 25 m/s and constant feed rate vft = 1 m/min. It was shown that the grinding of C45 steel causes strong work hardening of ferrite in surface...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublicationIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (),were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublicationIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (s), were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
Effect of annealing temperature on slurry erosion resistance of ferritic X10CrAlSi18 steel
PublicationIn the present work, the slurry erosion tests were carried out to investigate the influence of heat treatment on slurry erosion process of ferritic X10CrAlSi18 stainless steel using a slurry pot test rig. X10CrAlSi18 stainless steel was tested in as-received condition and after annealing at three different temperatures: 600°C, 800°C and 1000°C. Degradation of materials due to slurry erosion depends on many factors connected with...
-
Cyclic behaviour modelling of additively manufactured Ti-6Al-4V lattice structures
PublicationThe present work is concerned with the numerical modelling of the cyclic behaviour of Ti-6Al-4V lattice structures. In the study, diamond structures of titanium alloy produced by the additive laser powder bed fusion (LPBF) method with different degrees of relative density were used. Realistic geometric models of the studied mesostructures were generated using computed microtomography, taking into account the imperfections of the...
-
On modelling and non-linear elasto-plastic analysis of thin shells with deformable junctions
PublicationThe undeformed base surface of the irregular thin shell is modelled by the union of a finite number of regular smooth surface elements joined together along spatial curvilinear surface edges. The equilibrium conditions are formulated by postulating an appropriate form of the principle of virtual work, where also deformability of shell junctions is taken into account. The PVW is then discretised by C1 finite elements and the incremental-iterative...
-
The FEM analysis of pressure installation elements after simulated accidental overheating
PublicationThe paper presents innovative analysis focused on the safety aspects of existing pressure installation operation after overheating accidents. Results presented here can be applied in decision-making process concerning further operation of existing pressure installation after cooling system failure. In this paper the results of FEM analysis performed for a straight pipe and 90 degrees elbow, made of super duplex stainless steel,...
-
Guided waves for nondestructive diagnostics of embedded waveguides
PublicationThe thesis concentrates on comprehensive theoretical, numerical and experimental analysis of guided wave propagation in bars embedded in concrete or mortar. The investigations are focused on a particular type of objects representing a laboratory model of a ground anchor. Complex description of wave propagation phenomena in partially embedded bars is given and its application in...
-
Influence of low-temperature physical hardening on stiffness and tensile strength of asphalt concrete and stone mastic asphalt
PublicationThis paper presents laboratory testing of stiffness modulus and indirect tensile strength of three asphalt concrete (AC) and three stone mastic asphalt (SMA) mixes after isothermal storage at temperature of -20oC, at different time intervals up to 16 days. The tests under repeated dynamic loading showed physical hardening of all tested mixes which was manifested by an evident increase of their stiffness moduli after isothermal...
-
A procedure for elastoplastic hardening function identification.
PublicationThe inverse analysis method for identifying a nonlinear hardening function,which governs a plastic yielding of soil and rock materials in the framework of elastoplastic theory is presented. A concept of two stage finite element based on spatial discretization of computational space and hardening function space is introduced. The proposed inverse analysis can be classified as the output least squares method. The Levenberg Marquard...
-
Discussion on “Dynamic soil-structure interaction: A three-dimensional numerical approach and its application to the Lotung case study”. Poor performance of the HSS model
PublicationThe Hardening Soil Small (HSS) is a constitutive model being extension to the well established Hardening Soil Model (HS) accounting for the nonlinearity of small strain stiffness. It is implemented in commercial finite element computer codes for geotechnical analyses and used widely in research and design. The article deals with a problem known as overshooting after very small load reversals. It induces much higher stiffness than...
-
The lethal effect of hydrotechnical concrete on freshwater Bivalvia
PublicationMost hydrotechnical buildings under construction demand the concrete mixture to be set directly under water. The main reason for such a procedure is to limit the washing away of the the concrete binding mixture and to increase the efficiency of organisation of work so as to ensure continuity in concreting. The impact on the aquatic environment of recent developments in concrete technology and the use of new components has not yet...
-
Influence of PWHT Parameters on the Mechanical Properties and Microstructural Behavior of Multi-Pass GTAW Joints of P92 Steel
PublicationThe 9% Cr steels were developed for ultra-supercritical (USC) power plants to meet the requirements of high operating temperature and pressure. These steels are produced to operate at high temperatures where impact toughness is not a concern; however, it becomes important for the welded joints to have good impact toughness at room temperature for manufacturing. The present work investigates the effect of the post-weld heat treatment...
-
Advancements in the Additive Manufacturing of Magnesium and Aluminum Alloys through Laser-Based Approach
PublicationComplex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives such as reduced part numbers, greater functionality, and lightweight, among others. Polymers, metals, and ceramics are the few materials that can be used in AM technology, but metallic materials (Magnesium and Aluminum) are attracting more attention from the research and industrial point of view. Understanding the role...
-
Kształtowanie właściwości warstwy wierzchniej podczas szlifowania
PublicationW artykule scharakteryzowano szlifowanie powierzchni płaskich połączone ze zmianami właściwości warstwy wierzchniej, zwłaszcza poprzez jej zahartowanie. Omówiono problemy związane z tzw. technologią grind-hardening. Dodatkowo przedstawiono badania, w których po procesie szlifowania uzyskano lepsze właściwości elementu obrabianego wskutek odkształcenia plastycznego.
-
Determination of Thermophysical Parameters Involved in The Numerical Model to Predict the Temperature Field of Cast-In-Place Concrete Bridge Deck
PublicationThe paper dealswith a concept of a practical computationmethod to simulate the temperature distribution in an extradosed bridge deck. The main goal of the study is to develop a feasible model of hardening of concrete consistent with in-situ measurement capabilities. The presented investigations include laboratory tests of high performance concrete, measurements of temperature evolution in the bridge deck and above all, numerical...
-
Elastoplastic material law in 6-parameter nonlinear shell theory
PublicationWe develop the elastoplastic constitutive relations for nonlinear exact 6-parameter shell theory. A J2-type theory with strain hardening is formulated that takes into account asymmetric membrane strain measures. The incremental equations are solved using implicit Euler scheme with closest point projection algorithm. The presented test example shows the correctness of the proposed approach. Influence of micropolar material parameters...
-
The electromagnetic field intensity in industrial buildings
Open Research DataThe dataset contains the results of measurements of electromagnetic fields, separately electric and magnetic, carried out at selected places in the building of an operating industrial enterprise.
-
Dual-Setting Bone Cement Based On Magnesium Phosphate Modified with Glycol Methacrylate Designed for Biomedical Applications
PublicationMagnesium phosphate cement (MPC) is a suitable alternative for the currently used calcium phosphates, owing to beneficial properties like favorable resorption rate, fast hardening, and higher compressive strength. However, due to insufficient mechanical properties and high brittleness, further improvement is still expected. In this paper, we reported the preparation of a novel type of dual-setting cement based on MPC with poly(2-hydroxyethyl...
-
Comparative analysis of mechanical conditions in bone union following first metatarsophalangeal joint arthrodesis with varied locking plate positions: A finite element analysis
PublicationFirst metatarsophalangeal joint arthrodesis is a typical medical treatment performed in cases of arthritis or joint deformity. The gold standard for this procedure is arthrodesis stabilisation with the dorsally positioned plate. However, according to the authors’ previous studies, medially positioned plate provides greater bending stiffness. It is worth to compare the mechanical conditions for bone formation in the fracture callus...
-
Refinement of the Hardening Soil model within the small strain range
PublicationThe popularity of the elasto-plastic Hardening Soil (HS) model is based on simple parameter identification from standard testing and empirical formulas. The HS model is implemented in many commercial FE codes designed to analyse geotechnical problems. In its basic version, the stress–strain behaviour within the elastic range is subject to the hypoelastic power law, which assures the barotropy of the elastic stiffness. However,...
-
Glomerular disorders in diseases classified elsewhere - Male, 71 - Tissue image [12030630017641981]
Open Research DataThis is the histopathological image of KIDNEY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Glomerular disorders in diseases classified elsewhere - Male, 71 - Tissue image [12030630017646721]
Open Research DataThis is the histopathological image of KIDNEY tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
The Influence of Laser Alloying of Ti13Nb13Zr on Surface Topography and Properties
PublicationThe laser alloying is a continually developing surface treatment because of its significant and specific structuration of a surface. In particular, it is applied for Ti alloys, being now the most essential biomaterials` group for load-bearing implants. The present research was performed on the Ti13Nb13Zr alloy subject to laser modification in order to determine the treatment effects on surface topography and its some mechanical...
-
Transitional cell carcinoma, NOS - Male, 76 - Tissue image [10010729534331321]
Open Research DataThis is the histopathological image of OTHER AND UNSPECIFIED URINARY ORGANS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
Transitional cell carcinoma, NOS - Male, 76 - Tissue image [10010729534327311]
Open Research DataThis is the histopathological image of OTHER AND UNSPECIFIED URINARY ORGANS tissue sample obtained in Medical University Gdańsk and deposited in ZMDL-GUMED. The sample image was taken using: Pannoramic 250 3DHistech slide scanner (20x magnification) and saved to DICOM format.
-
The elasto-plastic numerical study of crack initiation in notched PMMA specimens under uniaxial loading conditions – Tension and torsion
PublicationThis paper presents the results of FEM numerical calculations aimed at describing the plastic strain and stress fields under critical loading conditions: tensile force or torsional moment. The calculations were carried out with reference to the results of experimental tensile and torsional tests of flat PMMA specimens weakened with V-notches of different root radii: 0.5, 2 and 10 mm. The procedure for conducting nonlinear numerical...
-
Isothermal Calorimetry and Compressive Strength Tests of Mortar Specimens for Determination of Apparent Activation Energy
PublicationThe hydration process of cementitious materials involves a thermally activated reaction that depends on the composition of the mixture and the curing temperature. The main parameter affecting the temperature variation of cast-in-place concrete is the apparent activation energy, which can be used for the efficient prediction of the temperature evolution and maturity index of hardening concrete. This paper discusses two methods to...
-
Evaluation of Low Temperature Properties of Rubberized Asphalt Mixtures
PublicationThe paper presents low-temperature test results of asphalt mixtures designed with use of bitumen modified by crumb rubber and also SBS polymer. Laboratory tests were conducted on two types of asphalt mixtures for wearing course – stone matrix asphalt (SMA 8) and porous asphalt (PA 8). This paper presents results of the following laboratory tests at low temperatures: TSRST test, three point bending creep test, fracture toughness...
-
Post-critical buckling of truncated conical carbon nanotubes considering surface effects embedding in a nonlinear Winkler substrate using the Rayleigh-Ritz method
PublicationThis research predicts theoretically post-critical axial buckling behavior of truncated conical carbon nanotubes (CCNTs) with several boundary conditions by assuming a nonlinear Winkler matrix. The post-buckling of CCNTs has been studied based on the Euler-Bernoulli beam model, Hamilton’s principle, Lagrangian strains, and nonlocal strain gradient theory. Both stiffness-hardening and stiffness-softening properties of the nanostructure...
-
Seismic pounding behavior of multi-story buildings in series considering the effect of infill panels
PublicationThe aim of the present paper is to study the influence of the infill panels on the seismic pounding response of adjacent structures in series. The contribution of the masonry infill has been simulated using equivalent diagonal compression struts. Steel frames have been assumed to have elastic-plastic behavior with 1% linear strain hardening. The dynamic contact analysis has been utilized where contact surface model (target and...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublicationThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Hydrogen Embrittlement and Oxide Layer E ect in the Cathodically Charged Zircaloy-2
PublicationThe present paper is aimed at determining the less investigated effects of hydrogen uptake on the microstructure and the mechanical behavior of the oxidized Zircaloy-2 alloy. The specimens were oxidized and charged with hydrogen. The different oxidation temperatures and cathodic current densities were applied. The scanning electron microscopy, X-ray electron diffraction spectroscopy, hydrogen absorption assessment, tensile, and...
-
Influence of soil–structure interaction on seismic pounding between steel frame buildings considering the effect of infill panels
PublicationThe present research aims to study the influence of the soil-structure interaction (SSI) and existence or absence of masonry infill panels in steel frame structures on the earthquake-induced pounding-involved response of adjacent buildings. The study was further extended to compare the pounding-involved behavior versus the independent behavior of structures without collisions, focusing much on dynamic behavior of single frames....
-
Effect of Thermal Treatment and Erosion Aggressiveness on Resistance of S235JR Steel to Cavitation and Slurry
PublicationS235JR steel is used in many applications, but its resistance to the erosion processes has been poorly studied. To investigate this resistance, cavitation, and slurry erosion tests were conducted. These tests were carried out at different erosion intensities, i.e., different flow rates in the cavitation tunnel with a system of barricades and different rotational speeds in the slurry pot. The steel was tested as-received and after...
-
Correlation between Compressive Strength and Heat of Hydration of Cement Mortars with Siliceous Fly Ash
PublicationThis paper presents the results of calorimetric and strength tests of mortars with ordinary Portland cement and two substitution rates (10 and 20%) of cement by siliceous fly ash. The prepared samples were cured under isothermal conditions at four different temperatures: 23, 33, 43 and 53 °C. Heat of hydration was measured using an isothermal calorimeter dedicated to monitor the hydration process of cementitious composites such...
-
Preparation of Well-Compatibilized PP/PC Blends and Foams Thereof
PublicationThe performance of polypropylene-poly(ethylene brassylate) block and graft copolymers and a polypropylene-polycaprolactone graft copolymer as compatibilizers for polypropylene-rich polypropylene/bisphenol A polycarbonate (PP/PC, 80/20 wt/wt) blends was elucidated. The copolymers were synthesized either by metal-catalyzed ring-opening polymerization or transesterification of a presynthesized polyester, initiated by hydroxyl-functionalized...
-
FEM modelling of screw displacement pile interaction with subsoil
PublicationPredicting the-settlement characteristics of piles is an important element in the designing of pile foundations. The most reliable method in evaluating pile-soil interaction is the static load test, preferably performed with instrumentation for measuring shaft and pile base resistances. This, however, is a mostly post-implementation test. In the design phase, prediction methods are needed, in which numerical simulations play an...
-
The magnetic field measurements in selected places of the industrial building
Open Research DataThe dataset is part of a comprehensive study on the assessment of the electromagnetic field intensity in a building of an operating industrial plant. Detailed results of magnetic field measurements, carried out in selected places of this building, are presented.
-
Nonlinear Free and Forced Vibrations of a Hyperelastic Micro/Nanobeam Considering Strain Stiffening Effect
PublicationIn recent years, the static and dynamic response of micro/nanobeams made of hyperelasticity materials received great attention. In the majority of studies in this area, the strain-stiffing effect that plays a major role in many hyperelastic materials has not been investigated deeply. Moreover, the influence of the size effect and large rotation for such a beam that is important for the large deformation was not addressed. This...
-
Influence of laser melting on surface layer properties of titanium alloy Ti6Al4V
PublicationIn time of rapid technology and medicine progress, implants are becoming more widely used in the human body, ranging from dental implants, stabilizing plates, screws, orthopaedic prostheses. For example, there are many types of hip prostheses used for hip replacement as well as various types of materials used for these orthopaedic prostheses. Properties of titanium alloys used in hip prostheses combined with good strength properties,...
-
Measurements of the heat of hydration released by concrete specimens cured under adiabatic conditions
Open Research DataThe DataSet contains measurements of heat of hydartion of concrete cubes (150 x 150 x 150 mm) cured under adiabatic conditions. The specimens were moulded from six types of concrete mixtures produced in the laboratory conditions. Mix #1: Portland cement CEM I 42.5R and gravel aggregate, mix #2: CEM I 42.5R and basalt aggregate, mix#3: Portland-composite...
-
Surface treatment of C80U steel by long CO2 laser pulses
PublicationThe paper presents the results of laser-melted C80U steel. The processed steel was placed between two permanent magnets and laser beam whose scanning velocity was 10 mm/s. CO2 laser beam was working in pulse mode. Pulses were generated at 100% of the average preset power of 700W, with 45 ms irradiation, zero interval between pulses and beginning of pulse repetition upon the achievement of the average laser power. During the operation,...
-
Potentials of Water Usage in urban Neighbourhood Structures
PublicationThis paper will treat about water influence and possibility of its usage in the urban neighborhood structures (e.g. districts, real estate properties, town parts) in the context of actual regional environmental problems and according to directories determined by European targets. It is not rare yet in the basic stage of urban design that water is treated as a threat, not a chance. In result planned structures are often built,...