Filters
total: 3844
filtered: 3567
displaying 1000 best results Help
Search results for: Influenza vaccines
-
INFLUENCE OF TEMPERATURE ON THE ACTIVITY OF ANAMMOX GRANULAR BIOMASS - SHORT AND LONG-TERM ASPECT
PublicationThe aim of this study was to determine a short-term and long-term effect of temperature on the anammox process rate and determination of temperature coefficients in the Arrhenius and Ratkowski equations. The short-term effects of temperature on the anammox biomass were investigated in batch tests at ten different temperatures in the range of 10-55 ̊C. The maximum rate 1.3 gN (gVSS·d)-1 observed at 40 ̊C. The minimum rate, close...
-
Influence of a Radio Frequency on RF Fingerprinting Accuracy Based on Ray Tracing Simulation
PublicationIn this paper the influence of a radio signal frequency on performance of Indoor Positioning System based on fingerprinting has been examined using ray-tracing simulations. It has been simulated how spatial distribution of an RF signal strength change with the signal’s frequency. The results were used to show its’ impact on the behavior of localization algorithms that are employing RSS measurements to determine node’s position...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublicationIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (),were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublicationIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (s), were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
The influence of pre- and postharvest treatments on selected biological and epigenetic activities of Brassica sprouts
PublicationIntroduction The Brassica vegetables are rich in glucosinolates (GLs), which are enzymatically hydrolysed to bioactive isothiocynates (ITC) and indoles, regarded as the most promising chemopreventing agents. However, in the majority of brassica sprouts the GL conversion into these beneficial derivatives occurs at the level of about 1 %, while in cabbage leaves exceeds 70%. Since sprouts represent plant material, which is frequently...
-
The influence of accumulation area and the length of pedestrian route on functioning of roundabouts with traffic signals
Publicationtraffic volumes. This kind of intersection is commonly used in the centres of Polish cities on multilane roads and fairly common in the case of tram lines running through a central island. The increase of traffic flow volumes on left turn and U-turn has made this type of roundabout difficult to operate. Small storage areas around central islands are critical places that significantly influence the capacity of this kind of intersection....
-
Influence of Spatial Structures of 316L Stainless Steel on Its Cavitation Erosion Resistance
PublicationCavitation erosion performance of modified macroscopic internal structure 316L stainless steel was investigated. The samples processed by means of SLM method were subjected to cavitation erosion test. The scanning electron microscope Philips 30/ESEM was used to examine morphology of eroded surface.
-
Oxidation Time Influence on the Structure of the Cobalt Base Clad Layer and Scale Morphology
PublicationZbadano wpływ czasu utleniania na mikrosrukutręi własności mechaniczne a w szczególności mikrotwardość, warstw wykonanych ze stopu kobaltu.Warstwy były wykonane za pomocą napawania plazmowego (PTA). Stop kobaltu podlegał utlenianiu w powietrzu w temperaturze 800 topni celsjusza w czasie 1, 22 i 200 godzin. w wyniku utleniania nastapiło uformowanie warstw zgorzeliny oraz nastapiły zmiany w mikrostrukturze. Zaobserwowano także zmiany...
-
An influence of the ship's block coefficient implementation on the evaluation of it's hull girder bending
PublicationAn influence of the three different ways of implementation ship's block coefficient δ (three geometrical models) on the stresses due to wave bending moment have been investigated. Two models have been applied and compared: beam one (description of the shape usingparameters) and FEM shell model (direct representation of the shape). The outcomes have been compared to Polish Register of Shipping (PRS) rules. The results show that...
-
Influence of the glycolysis agent on the structure of the glycolysates obtained from polyether-urethane wastes
PublicationW pracy zaprezentowano wybrane wyniki badań wpływu środków glikolizujących na strukturę glikolizatów otrzymywanych w procesie glikolizy odpadowych pianek polietero-uretanowych.
-
The influence of selenium addition during seeds' germination on the biological properties of obtained sprouts
PublicationSelenium plays a vital role in human body, because in the form of aminoacids (Se-methionine, Se-cysteine) it is found in the active centres of over 25 enzymes, including those regarded as 'cytoprotective'. Unfortunatelly, its daily intake in Poland and other European countries is lower than predicted by dietary recommendations. The consequences of selenium deficiency in diet might be severe, including higher susceptibility to cardio-vascular...
-
Influence of spatial structures of 316L stainless steel on its cavitation erosion resistance
Publication -
Studies on the influence of technological variants of finishing machining on flow of parts in flexible manufacturing
PublicationIn the article below the problems of influence of variants of finishing processing on flow of machining parts in flexible manufacturing system were presented. The investigations were carried out the technological processes for piston rods and rams of hydraulic cylinders. There were also presented model variants of technological processes for piston rods finished with the burnishing. In these studies the influence of technological...
-
Allergic reactions as a defense of the organism to the influence of implants components made of stainless steel
PublicationDue to the increasing number of cases of hypersensitivity caused by direct contact with metals, as well as the increasing demand for implants in humans all ages numerous studies on the effects of the impact of implant components are being carried out. The paper presents the phenomenon of etiology of allergy in general terms and in relation to the biomaterials used in medicine. There have been characterized in terms of impact on...
-
Interactions of dissolved dsDNA with intercalating drug by anodic voltammetry and spectroscopy. Influence of pH
PublicationOddziaływanie związku przeciwnowotworowego C-1305 z DNA było badane przy pomocy impulsowej voltametrii różnicowej oraz spektroskopii UV/Vis. Triazoloakrydon C-1305 oddziałuje z DNA na dwóch drogach: przez interkalacje pomiedzy pary zasad oraz przez wiązanie sie w małym rowku helisy. W fizjologicznym pH (7,4) stałe wiązania wynoszą: K1=3,36E+5 i K2=0,18E+5 [1/M] a wielkość miejsca wiązania: n1=2,5 i n2=4,0, odpowiednio dla pierwszego...
-
Influence of Pumped-Storage Power Plant on Physical and Ecological State of Lake Żarnowiec
PublicationOd 1983 roku istnieje elektrownia szczytowo-pompowa w Żarnowcu. Od 1973 roku do chwili obecnej prowadzono badania stanu ekologicznegi, chemicznego i fizicznego wód jeziora Żarnowieckiego. W artykule przedstawiono wyniki tych badań i na ich podstawie oceniono wpływ pracy elektrowni na stan jeziora.
-
Influence of landfill leachate on municipal wastewater treatment - model plant(WWTP-MP)
PublicationAbstract In the current study, wastewater treatment model plant (WWTP-MP) was used to investigate the possibilities of landfill leachate co-treatment together with municipal wastewater. The WWT-MP, designed as an A2O multiphase system, was fed with the raw municipal wastewater (from the WWTP Gdańsk "Wschód'', Qav.=82x103 m3/d) with increasing, from 1 to 5 % (vol.), quantity of landfill leachate (collected from Gdańsk landfill ''Szadółki")....
-
Influence of laser remelting at cryogenic conditions on corrosion resistance of non-ferrous alloys
PublicationCelem nadtapiania laserowego elementów wytwarzanych z stopów aluminium, miedzi i tytanu jest uzyskanie wysokiej twadrości i odporności na korozję dla wydłużenia okresu ich eksploatacji w rezultacie ich szybkiej krystalizacji. Końcowa mikrostruktura, skład fazowy i właściwości wymienionych stopów zależą od parametrów obróbki laserowej oraz budowy wykresów równowagi fazowej. W artykule przedstawiono wpływ laserowego nadtapiania...
-
Influence of Preparation Procedure on Physicochemical and Antibacterial Properties of Titanate Nanotubes Modified with Silver
Publication -
Influence of Magnesium Oxide on the Structure and Catalytic Activity of the Wustite Catalyst for Ammonia Synthesis
Publication -
Influence of titanium dioxide activated under visible light on survival of mold fungi
Publication -
The influence of magnetic water treatment on CaCO3 scale formation in membrane distillation process
Publication -
Influence of morphology of PVDF capillary membranes on the performance of direct contact membrane distillation
Publication -
Influence of porous coating on heat transfer during R22 and R134a flow boiling.
PublicationPrzedstawiono wpływ powłoki porowatej na przenoszenie ciepła i spadku ciśnienia podczas wrzenia w przepływie czynników chłodniczych, R22 i R134a.
-
Effects of loading pattern and lubricant pressure influence on bearing alloy fatigue characteristics
PublicationOpisano wyniki testów zmęczeniowych przeprowadzonych dla stopu łożyskowego AlSn (11,3 Cu 1,2) osadzonego na taśmie stalowej. Doświadczalnie określono wartości obciążeń niszczących dla różnych warunków obciążenia: dla obciążeń zginających wahadłowych, dla obciążeń zginających wahadłowych przy równoczesnym działaniu słabego lub zmiennego ciśnienia w komorze olejowej.
-
The formal safety assessment and influence of human factor in application to chosen ship's type
PublicationTragedia jednego ze statków typu ro-ro pokazała podatność tego typu statków na utratę stateczności, przewrócenie się, a w ostateczności zatonięcie. Wszystkie ro-rowce charakteryzują się małym zanurzeniem, a wynurzona część kadłuba podatna jest na działanie wiatru. Jeżeli dodatkowo w takich warunkach dochodzi element nieprawidłowego rozmieszczenia pojazdów i ich słabego zamocowania to groźba przesunięcia ładunku staje się realna....
-
The influence of frequency controlled ac drives on vibration and audible noise level on ships
PublicationOkreślono korelacje między zakłóceniami elektrycznymi a wibracjami i hałasem w okrętowych układach napędowych z przemiennikami częstotliwości. Wskazano na destrukcyjny wpływ tych czynników na jakość życia załóg pływających.
-
Influence of sample thickness non-uniformities on the modulated photocur-rents in amorphous solids
PublicationOtrzymano przybliżone wzory opisujące modulowane fotoprądy dla przypadków próbki kanapkowej o nierównomiernej grubości, reprezentowanej przez układ równolegle połączonych próbek o różnych grubościach. Na ich podstawie obliczono przebieg fotoprądów dla przypadku jednorodnego i gaussowskiego rozkładu grubości próbki oraz dla wykładniczego rozkładu pułapek.
-
Rough-neutral approach to testing the influence of visual cues on surround sound perception
PublicationW rozdziale przedstawiono problem wpływu obrazu na odbierany w systemie doo-kólny dźwięk. W celu określenia tego wpływu przeprowadzono testy subiektyw-ne. Do obróbki wyników testów subiektywnych użyto systemu hybrydowego zło-żonego z algorytmu genetycznego, sieci neuronowej oraz algorytmu opartego ometodę zbiorów przybliżonych. Zadaniem tego ostatniego elementu systemu byłowyznaczanie reguł opisujących wpływ postrzeganego obrazu...
-
Influence of ci rcuit parameters on the procces of current transfer in thehybrid circuit breaker.
PublicationW artykule przedstawiono działanie hybrydowego bezstykowego ogranicznika prądów zwarciowych w oparciu o symulację komputerową oraz porównanie eksperymentu z symulacją komputerową przy pomocy programu MATLAB i PSPICE. Przedstawiono również wady i zalety obliczeń numerycznych przeprowadzonych z zastosowaniem komercyjnych programów na analizę działania łącznika hybrydowego.W analizie uwzględniono model hybrydowego ogranicznika...
-
Influence of laser beam machining on the cavitation resistance of Fe-Cr-Co clad.
PublicationW pracy przedstawiono wpływ laserowego nagrzewania bezzmiany stanu skupienia i laserowego przetapiania napoin ze stopu Fe-Cr-Co na ich odporność kawitacyjną. Badania kawitacyjne prowadzono na stanowisku z wirującą tarczą. Plastyczne odkształcenia powierzchni określano za pomocą analizy obrazów erodowanych powierzchni. Uzyskane rezultaty wskazują, że laserowo obrabiane powierzchnie miały różną podatność do plastycznego odkształcania...
-
Influence of the analyzing window on electrode impedance measurement by thecontinuous freqency scanning method
PublicationPrzeprowadzono pomiary impedancyjne modelowego układu elektrycznego RC techniką ciągłego skanowania częstotliwościowego. Wyznaczono impedancję modelowego układu dla różnych okien analizujących oraz ich różnych wielkości. Wyznaczone dla różnych okien analizujących wartości R i C porównywano z wartościami rzeczywistymi. Stwierdzono wpływ rodzaju okna analizującego oraz jego długość na dokładność otrzymywanych wyników.
-
Influence of the steam within seals and glands of the turbine on its rotor motion stability.
PublicationPrzedstawiono metodę obliczania charakterystyk dynamicznych wpływu parowych uszczelnień turbin na ich dynamikę i stateczność ruchu wirników. Zarysowano model ''masowy'' uszczelnienia. Podano przykłady zastosowań.
-
Influence of frame sawing machine´s kinematics on saw blade tooth wear.
PublicationW pracy przedstawiono wpływ kinematyki pilarki ramowej na zużycie ostrzy piłtrakowych.
-
Influence of Annealing Atmospheres on Photoelectrochemical Activity of TiO2 Nanotubes Modified with AuCu Nanoparticles
PublicationIn this article, we studied the annealing process of AuCu layers deposited on TiO2 nanotubes (NTs) conducted in various atmospheres such as air, vacuum, argon, and hydrogen in order to obtain materials active in both visible and UV–vis ranges. The material fabrication route covers the electrochemical anodization of a Ti plate, followed by thin AuCu film magnetron sputtering and further thermal treatment. Scanning electron microscopy...
-
Influence of the Shear Cap Size and Stiffness on the Distribution of Shear Forces in Flat Slabs
PublicationThe scope of this paper is to investigate analytically and numerically the influence of shear cap size and stiffness on the distribution of shear forces in flat slabs in a slab–column-connections-reinforced concrete structure. The effect of support (shear cap) stiffness on the calculation of the length of the shear control perimeter according to the available methods is presented. Based on the analysis, the authors indicate in...
-
Influence of Different Nanometals Implemented in PMMA Bone Cement on Biological and Mechanical Properties
PublicationCemented arthroplasty is a common process to fix prostheses when a patient becomes older and his/her bone quality deteriorates. The applied cements are biocompatible, can transfer loads, and dampen vibrations, but do not provide antibacterial protection. The present work is aimed at the development of cement with antibacterial effectivity achieved with the implementation of nanoparticles of different metals. The powders of Ag,...
-
In-Reactor Polypropylene Functionalization─The Influence of Catalyst Structures and Reaction Conditions on the Catalytic Performance
PublicationTo unravel the relationship between silylene-bridged metallocene catalyst structures and polymerization conditions and their effect on the performance in in-reactor functionalization of polypropylene, the behaviors of rac-Me2Si(2-Me-4-Ph-Ind)2ZrCl2/MMAO, rac-Me2Si(Ind)2ZrCl2, rac-Me2Si(2-Me-4-Ph-Ind)2HfCl2, and rac-Me2Si(Ind)2HfCl2 in propylene/aluminum alkyl-passivated 10-undecen-1-ol copolymerization were compared. Kinetic analysis...
-
The influence of inflation pressure and ambient temperature on the value of the truck tires rolling resistance
PublicationThe articlediscusses the effect of inflation pressure and the ambient temperature on the value of the rolling resistance of truck tires which directly translates into fuel consumption. For this purpose, a series of measurements was made at two ambient temperatures (at 25°C and -15°C), using different pumping pressures.
-
PARAMETERS OF THE ELECTROPHORETIC DEPOSITION PROCESS AND ITS INFLUENCE ON THE MORPHOLOGY OF HYDROXYAPATITE COATINGS. REVIEW
PublicationMetallic materials intended for bone implants should exhibit not only appropriate mechanical properties, but also high biocompatibility. The surface treatment modifications, for example acidic treatment, laser treatment, ion implantation and deposition of highly biocompatible coatings, are practiced. One of the most popular methods of surface modification is to deposit hydroxyapatite (HAp) coatings. HAp naturally occurs in human...
-
Influence of geometrical and operational parameters on tooth wear in the working mechanism of a satellite motor
PublicationThis article describes the phenomena affecting the wear of the rotor of the working mechanism in a hydraulic satellite motor. The basic geometrical relationships that allow the calculation of the coordinates of the points of contact between the satellite and the rotor and the curvature are presented. A method for calculating the number of contacts of the satellite teeth with the rotor teeth and of the satellite teeth with the curvature...
-
Influence of diffusion on nonradiative energy transfer between FMN molecules in aqueous solution
PublicationZmierzono zależności wydajności kwantowej roztworów wodnych FMN w zakresie koncentracji od 6,31x10^-5 do 1,8x10^-2 M w temperaturach 298,2 i 323,9 K. Otrzymane wyniki porównano z analogicznymi, uzyskanymi teoretycznie na podstawie modelu nie biorącego i biorącego pod uwagę dyfuzję molekuł fluoroforu. Porównanie wykazuje, że dla badanych roztworów dyfuzja nie może być pominięta, oraz, że dla uzyskania zgodności otrzymanych wyników...
-
Influence of silver nanoparticles addition on antibacterial properties of PEO coatings formed on magnesium
PublicationMagnesium is a biodegradable material and thus could be a choice for bone fixation devices and implants with a specific purpose. This study aims to enhance the anti-corrosive, biocompatible, and antibacterial properties on magnesium-based materials through ceramic coatings formation. To achieve this the silicate-based electrolyte was used to create of Plasma Electrolytic Oxidation (PEO) coatings. During investigation the bioactive...
-
Influence of operating pressure on the durability of a satellite hydraulic motor supplied by rapeseed oil
PublicationThis article describes the results of a durability test of a hydraulic satellite motor supplied by rapeseed oil. The tests were carried out on a test stand in a power recuperation system. The tests of the motor were carried out at a constant shaft speed for three fixed pressure drops in the motor. This made it possible to demonstrate the influence of the motor operating pressure on the durability of the satellite mechanism. The...
-
Numerical simulations of the influence of injection moulding parameters on mechanical properties of the polyamide composite
PublicationZaprezentowano wyniki symulacji numerycznej wpływu parametrów technologicznych procesu wtryskiwania na wybrane właściwości mechaniczne kompozytu poliamidowego. Symulacje przeprowadzono z wykorzystaniem programu Cadmould-3d.
-
Influence of the structure of vanadate-phosphate glasses containing alkali ions on their polaronic properties
PublicationBadano wpływ struktury szkieł wanadanowo-fosforanowych zawierających jony metali alkalicznych na ich właściwości polaronowe metodą NMR.
-
The influence of G2 arrest abrogation on the long-term cytotoxicity of different genotoxic lesions
PublicationJak się uważa, zdolność komórek nowotworowych z uszkodzeniami DNA do zatrzymywania progresji w cyklu komórkowym w fazie G2 wydłuża czas na reperację tych uszkodzeń i zwiększa zdolność do przeżycia tych komórek. W pracy badaliśmy wpływ skrócenia bloku w fazie G2 w komórkach dwóch typów białaczek, poddanych działaniu związków przeciwnowotworowych indukujących różne typy uszkodzeń DNA, na efekt cytotoksyczny tych związków. Zwiększenie...
-
Influence of Laser Modification on the Surface Character of Biomaterials: Titanium and Its Alloys—A Review
PublicationLaser surface modification is a widely available and simple technique that can be applied to different types of materials. It has been shown that by using a laser heat source, reproducible surfaces can be obtained, which is particularly important when developing materials for medical applications. The laser modification of titanium and its alloys is advantageous due to the possibility of controlling selected parameters and properties...
-
Bio‐polyols synthesized by liquefaction of cellulose: Influence of liquefaction solvent molecular weight
PublicationCurrently, the plastics industry including polyurethanes is based on the use of petrochemicals. For this reason, scientists are looking for new types of renewable resources for the substitution of petrochemical substances. This work aims to evaluate the effect of polyethylene glycols (PEG) with different molecular mass impact on properties of bio-based polyols synthesized via biomass liquefaction of cellulose. To date, research...
-
Influence of hydrogen on a nanocrystalline high-entropy oxide with application potential in hydrogen technologies
PublicationThe influence of hydrogen on a (Co0⋅2Cu0⋅2Mg0⋅2Ni0⋅2Zn0.2)O HEO with a rock salt structure was studied. Two forms of this HEO (nanopowder and sinter) were prepared via mechanochemical synthesis (MS) and additional heat treatment, respectively. The chemical stability of the synthesized samples in a pure hydrogen atmosphere was investigated using Sievert’s technique. High-pressure hydrogenation at 250 ◦C had no noticeable effect...