Search
Filters
total: 874
filtered: 755
-
Catalog
Chosen catalog filters
Search results for: MARITIME REFRIGERATION
-
Influence of pitting corrosion on strength of steel ships and offshore structures
PublicationPraca dotyczy wpływu korozji wżerowej na własności mechaniczne stali o zwykłej i podwyższonej wytrzymałości oraz na wytrzymałość stalowych konstrukcji przy obciążeniach statycznych i quasi- statycznych. Artykuł oparty jest głównie na japońskich publikacjach. W próbie rozciągania, korozja wżerowa obniża nieznacznie obciążenie odpowiadające granicy plastyczności Re(nieznacznie) i wytrzymałości na rozciąganie Rm (silniej, redukuje...
-
Multi-objective weather routing of sailboats considering wave resistance
PublicationThe article presents a method to determine the route of a sailing vessel with the aid of deterministic algorithms. The method assumes that the area in which the route is to be determined is limited and the basic input data comprise the wind vector and the speed characteristic of the vessel. Compared to previous works of the authors, the present article additionally takes into account the effect of sea waves with the resultant resistance...
-
OPERATION OF TWO-SHAFT GAS TURBINE IN THE RANGE OF OPEN ANTI-SURGE VALVE
PublicationThis paper presents experimental tests of full-scale two-shaft gas turbine in the range of open anti-surge valve (ASV). The tests were carried out in a laboratory gas- turbine test stand belonging to Department of Automation and Power Engineering , Faculty of Ocean Engineering and Ship Technology , Gdańsk University of Technology. The tests covered the start-up and low load operation of the turbine set in the range of open...
-
Bearing estimation using double frequency reassignment for a linear passive array
PublicationThe paper demonstrates the use of frequency reassignment for bearing estimation. For this task, signals derived from a linear equispaced passive array are used. The presented method makes use of Fourier transformation based spatial spectrum estimation. It is further developed through the application of two-dimensional reassignment, which leads to obtaining highly concentrated energy distributions in the joint frequency-angle domain...
-
Theoretical Model of Acoustic Wave Propagation in Shallow Water
PublicationThe work is devoted to the propagation of low frequency waves in a shallow sea. As a source of acoustic waves, underwater disturbances generated by ships were adopted. A specific feature of the propagation of acoustic waves in shallow water is the proximity of boundaries of the limiting media characterised by different impedance properties, which affects the acoustic field coming from a source situated in the water layer “ deformed”...
-
Simulation studies into quayside transport and storage yard operations in container terminals
PublicationThe focus of the paper is on quayside transport and storage yard operations in the sea container terminals. Developed algorithms for solving the issues of load handling and storage space allocation have been applied in the frame of adopted simulation model. The criteria chosen for decision making involved the total makespan of vessel unloading and the utilisation levels of the transportation trucks. Recommendations for unloading...
-
Features of load and wear of main propulsion devices on sea-going ships with piston combustion engines and their impact on changes in technical states of the systems
PublicationThe paper presents the specificity of operation of propulsion systems of seagoing ships which causes the need to control the load on them, especially on their engines called main engines. The characteristics of the load on the propulsion systems, especially on the main engines as well as on the shaft lines and propellers driven by the engines, along with the process of wear in tribological joints (sliding tribological systems)...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART V) METHODS ENSURING CORRECT START-UP OF HYDRAULIC COMPONENTS OF SHIP’S ONBOARD DEVICES IN LOW AMBIENT TEMPERATURES
PublicationA large number of hydraulic devices and systems are started in low ambient temperatures. A good example of such a device is the hoisting winch on the ship. Starting hydraulic drive units in thermal shock conditions (rapid supply of hot oil to the cold unit) may lead to incorrect operation of the actuating system, for instance, due to the loss of clearance between cooperating elements. The article presents methods to prevent the...
-
MAPPING SOUTH BALTIC NEAR-SHORE BATHYMETRY USING SENTINEL-2 OBSERVATIONS
PublicationOne of the most promising new applications of remote observation satellite systems (RO) is the near-shore bathymetry estimation based on spaceborn multispectral imageries. In recent years, many experiments aiming to estimate bathymetry in optically shallow water with the use of remote optical observations have been presented. In this paper, optimal models of satellite derived bathymetry (SDB) for relatively turbid waters of the...
-
Technical State Assessment of Charge Exchange System of Self-Ignition Engine, Based On the Exhaust Gas Composition Testing
PublicationThis paper presents possible use of results of exhaust gas composition testing of self - ignition engine for technical state assessment of its charge exchange system under assumption that there is strong correlation between considered structure parameters and output signals in the form of concentration of toxic compounds (ZT) as well as unambiguous character of their changes. Concentration of the analyzed ZT may be hence considered...
-
Visualization of a lifeboat motion during lowering along ship’s side
PublicationThis paper presents description of a computer program for motion visualization of a lifeboat lowered along ship’s side. The program is a post-processor which reads results of numerical calculations of simulated objects’ motions. The data is used to create scene composed of 3D surfaces to visualize mutual spatial positions of a lifeboat, ship’s side and water waving surface. Since the numerical data contain description of a simulation...
-
A method to assess transverse vibration energy of ship propeller shaft for diagnostic purposes
PublicationThe article discusses a key problem of ship propulsion system vibration diagnostics, which concerns assessing this part of mechanical energy transmitted from the main engine to the ship propeller which is dissipated due to propeller shaft vibration. A simplified calculation model is proposed which allows the total energy of the generated torsional vibration to be assessed from the shaft deflection amplitude measured at the mind-span...
-
CAUSALITY IN MODELS OF THERMAL PROCESSES IN SHIP ENGINE ROOMS WITH THE USE OF BOND GRAPH (BG) METHOD
PublicationWith a single approach to modeling elements of different physical nature, the method of Bond Graph (BG) is particularly well suited for modeling energy systems consisting of mechanical, thermal, electrical and hydraulic elements that operate in the power system engine room. The paper refers to the earlier presented new concept of thermal process modeling using the BG method. The authors own suggestions for determining causality...
-
MEMS Technology Quality Requirements as Applied to Multibeam Echosounder
PublicationSmall, lightweight, power-efficient, and low-cost microelectromechanical system (MEMS) inertial sensors and microcontrollers, available in the market today, help reduce the instability of Multibeam Sonars. Current MEMS inertial measurement units (IMUs) come in many shapes, sizes, and costs — depending on the application and performance required. Although MEMS inertial sensors offer affordable, appropriately scaled units, they are...
-
APPLICABILITY OF INLET AIR FOGGING TO MARINE GAS TURBINE
PublicationThe dependency of marine gas turbine on the ambient temperature leads to a decrease of the gas turbine power output in arid areas. Very often gas turbine power output demand is high and the power margins originally designed into the driver , has been exhausted. In such circumstances the inlet air fogging is an effective compensation of gas turbine power. In this paper an analysis of inlet air fogging applicability to marine gas...
-
ANALYSIS OF IMPACT of SHIP model parameters on changes of control quality index in ship dynamic positioning system
PublicationIn this work there is presented an analysis of impact of ship model parameters on changes of control quality index in a ship dynamic positioning system designed with the use of a backstepping adaptive controller. Assessment of the impact of ship model parameters was performed on the basis of Pareto-Lorentz curves and ABC method in order to determine sets of the parameters which have either crucial, moderate or low impact on objective...
-
Accuracy Of The GPS Positioning System In The Context Of Increasing The Number Of Satellites In The Constellation
Publication -
Position accuracy evaluation of the modernized Polish DGPS
Publication -
Application of an Autonomous/Unmanned Survey Vessel (ASV/USV) in Bathymetric Measurements
Publication -
Polish DGPS System: 1995–2017 – Study of Positioning Accuracy
Publication -
A Method for The Assessing of Reliability Characteristics Relevant to an Assumed Position-Fixing Accuracy in Navigational Positioning Systems
PublicationThis paper presents a method which makes it possible to determine reliability characteristics of navigational positioning systems, relevant to an assumed value of permissible error in position fixing. The method allows to calculate: availability , reliability as well as operation continuity of position fixing system for an assumed, determined on the basis of formal requirements - both worldwide and national, position-fixing accuracy....
-
GNSS INVENTORY OF HISTORIC NARROW-GAUGE RAILWAY LINE IN KOSZALIN UNDER EXTREMELY UNFAVORABLE MEASUREMENTS CONDITIONS FROM THE POINT OF VIEW OF SATELLITE SIGNALS AVAILABILITY
PublicationA team of academic researchers from the Gdańsk University of Technology, Gdynia Maritime University and the Polish Naval Academy have been working since 2009 on the methodology of using active GNSS geodetic networks for geodetic inventory of railways and on adapting this measurement technique for designing geometric layouts of railway and tram lines. Over the years, the team tested a variety of configurations of receivers and settings...
-
Data-driven, probabilistic model for attainable speed for ships approaching Gdańsk harbour
PublicationThe growing demand for maritime transportation leads to increased traffic in ports. From this arises the need to observe the consequences of the specific speed ships reach when approaching seaports. However, usually the analyzed cases refer only to the statistical evaluation of the studied phenomenon or to the empirical modelling, ignoring the mutual influence of variables such as ship type, length or weather conditions. In this...
-
Advanced super-hydrophobic polymer-based porous absorbents for the treatment of oil-polluted water
PublicationThe threat of environmental pollution caused by spilled oil is rapidly increasing along with the expansion of oil exploration, the development of maritime activities and industrial growth. Oil spill incidents usually affect seriously the ecosystem and human life. Therefore, the treatment and recovery of the oil spill have been considered as an ultra-important issue to protect the environment and to minimize its negative impacts...
-
Experimental research on over-laminated steel sandwich panel connection to determine the form of fatigue failure
PublicationThe novel means of transport need to meet rising both the economic and ecologic requirements. In recent years the International Maritime Organization (IMO) introduced new measure of ship energy efficiency (the EEDI index), as well as new regulations regarding higher quality of fuel (so called Tier limits). It resulted in much higher interest of the technological development of ships. One of the solution having great potential is...
-
Three-dimensional geographically weighted inverse regression (3GWR) model for satellite derived bathymetry using Sentinel-2 observations
PublicationCurrent trends of development of satellite derived bathymetry (SDB) models rely on applying calibration techniques including analytical approaches, neuro-fuzzy systems, regression optimization and others. In most of the cases, the SDB models are calibrated and verified for test sites, that provide favourable conditions for the remote derivation of bathymetry such as high water clarity, homogenous bottom type, low amount of sediment...
-
The influence of the development of private air communication on the architecture and urban planning of the 21st century
PublicationIn the first part, the article describes the stages of the development of gyroplanes and the influence of wartime policy on the interest in light aircraft. Also presented are links and the possibilities of using gyroplanes in various sectors of the economy. The authors, based on source texts, present the current position of the aviation industry in the Polish economy and attempt to diagnose its development capabilities. As a result,...
-
Effects of Peripheral Chemoreceptors Deactivation on Sympathetic Activity in Heart Transplant Recipients
Publication -
Ochrona zdrowia i życia na morzu. Statki szpitale
PublicationRatowanie życia oraz opieka nad chorym w środowisku morskim jest szczególnym wyzwaniem i zadaniem. Na początku XX-tego wieku nastąpił przełom w niesieniu pomocy osobom rannym oraz chorym, którzy ze względu na pobyt na obiekcie pływającym miały ograniczony dostęp do lekarza czy ośrodka zdrowia. Pojawiły się statki, które pełniły rolę pływających szpitali. Ich działalność wynikała z określonych sytuacji niosących zagrożenie dla zdrowia...
-
Advanced Bayesian study on inland navigational risk of remotely controlled autonomous ship
PublicationThe arise of autonomous ships has necessitated the development of new risk assessment techniques and methods. This study proposes a new framework for navigational risk assessment of remotely controlled Maritime Autonomous Surface Ships (MASS). This framework establishes a set of risk influencing factors affecting safety of navigation of a remotely-controlled MASS. Next, model parameters are defined based on the risk factors, and...
-
A framework to analyse the probability of accidental hull girder failure considering advanced corrosion degradation for risk-based ship design
PublicationShip’s hull girder failure could result from maritime accident that can cause human life loss, environmental disaster, and major economic impacts. In risk-based ship design paradigm, accounting for rare phenomena (e.g. ship-ship collision or grounding) is important to provide safe and durable structure. In-service corrosion-induced hull degradation should be considered at the design stage, as it can significantly affect structural...
-
Thermal efficiency investigations on the self-ignition test engine fed with marine low sulfur diesel fuels
PublicationWithin the article an issues of implementing the new kinds of marine diesel fuels into ships’ operation was described taking into ac-count restrictions on the permissible sulphur content introduced by the International Maritime Organization. This is a new situation for ship owners and fuel producers, which forces the necessity to carry out laboratory research tests on especially adapted engine stands. How to elaborate the method...
-
Equivalent standard manoeuvres for pod-driven ships
PublicationProcedures for carrying out the manoeuvring tests presented in International Maritime Organisation (IMO) resolution MSC.137(76) are based on the capabilities of ships with conventional steering-propulsion systems. Therefore they do not correspond to ships with other steering-propulsion devices, like pod drives. IMO is aware of this shortcoming and for ships with non-conventional steering and propulsion system may permit the use...
-
Determining the Seasonal Variability of the Territorial Sea Baseline in Poland (2018–2020) Using Integrated USV/GNSS/SBES Measurements
PublicationThe Territorial Sea Baseline (TSB) allows coastal states to define the maritime boundaries, such as: contiguous zone, continental shelf, exclusive economic zone and territorial sea. Their delimitations determine what rights (jurisdiction and sovereignty) a given coastal state is entitled to. For many years, the problem of delimiting baseline was considered in two aspects: legal (lack of clear-cut regulations and different interpretations)...
-
Study of the formation of calcareous deposits on cathodically protected steel in Baltic sea water
PublicationPurpose – The purpose of this paper is to investigate whether the sedimentation of calcareous deposits occurs on cathodically protected steel in Baltic sea water. Design/methodology/approach – Steel electrodes were cathodically polarized in natural Baltic sea water at potential þ0.150 V vs Zn electrode in potentiostatic mode. During exposure chronoamperometric measurements were carried out. After the exposure, the electrode’s surface...
-
NUMERICAL ESTIMATION OF HULL HYDRODYNAMIC DERIVATIVES IN SHIP MANOUVERING PREDICTION
PublicationOperating in crowded waterways pose a risk of accidents and disasters due to maneuvering limitations of the ship. In order to predict ship’s maneuvering characteristics at the design stage, model tests are often executed as the most accurate prediction tool. Two approaches can be distinguished here: free running model tests and numerical simulations based on planar motion model with the use of hydrodynamic derivatives obtained...
-
TEORIA DECYZYJNYCH PROCESÓW SEMI-MARKOWA I JEJ ZASTOSOWANIE W PROJEKTOWANIU I EKSPLOATACJI OKRĘTOWYCH SILNIKÓW GŁÓWNYCH I INNYCH URZĄDZEŃ SIŁOWNI OKRĘTOWYCH
PublicationW referacie zaprezentowano znaczenie teorii procesów semi-Markowa w naukach technicznych, zwłaszcza w teorii niezawodności urządzeń technicznych, teorii bezpieczeństwa ich działania oraz statystycznej teorii podejmowania decyzji eksploatacyjnych. W referacie wyeksponowano także przydatność teorii procesów semi-Markowa w teorii i praktyce eksploatacji wspomnianych urządzeń technicznych na przykładzie tak istotnych urządzeń w transporcie...
-
Distribution and extent of benthic habitats in Puck Bay (Gulf of Gdańsk, southern Baltic Sea)
PublicationThe majority of the southern Baltic Sea seabed encompasses homogenous soft-bottom sediments of limited productivity and low biological diversity, but shallow productive areas in the coastal zone such as wetlands, vegetated lagoons and sheltered bays show a high variety of benthic habitat types offering favourable biotopic conditions for benthic fauna. Within Polish marine areas, semi-enclosed Puck Bay (the western part of the...
-
An attempt to create a digital reconstruction of the Copper Ship = Próba cyfrowej rekonstrukcji kadłuba wraku Miedziowca
PublicationThis study presents an attempt to create a digital reconstruction of the W-5 shipwreck (the Copper Ship) based on data acquired by 3D scanning of structural components held at the National Maritime Museum in Gdańsk and on a physical reconstruction model of the ship’s hull. A digital reconstruction would facilitate analysis of various possible options for the structural design of the hull, and would enable the preparation of a model for...
-
Design and Evaluation of the Compact and Autonomous Energy Subsystem of a Wave Energy Converter
PublicationThis paper presents the results of the design process focused on the development of the energy subsystem (ES) of a wave energy converter (WEC). The ES is an important electrical part that significantly affects the energy reliability and energy efficiency of the entire WEC device. The designed ES was intended for compact WECs powering IoT network devices working in the distributed grid. The developed ES is an electronic circuit...
-
Museums of Gdansk - Tourism Products or Signs of Remembrance?
PublicationMuseum buildings constitute a significant element in the composition and functionality of contemporary cities. They are both their attractions and landmarks. The article presents a case study illustrating the relation between museum buildings and their location, as well as the showcased exhibition. The article aims at demonstrating the way in which those elements form a harmonious whole - a cultural tourism product affecting the...
-
Laboratory station for research of the innovative dry method of exhaust gas desulfurization for an engine powered with residual fuel
PublicationContemporary methods of exhaust gas desulfurization in marine engines are all expensive methods (4-5 million euro). This is, among other reasons, due to the limited market audience, but primarily due to the monop-olized position of manufacturers offering fabrication and assembly of this type of marine ship installations. Proposed as part of a research project financed by the Regional Fund for Environmental Protection and Maritime...
-
Evaluation Methodology for Ship’s Planned Maintenance System Database
Publication -
Shipowner’s Impact on Planned Maintenance System Database Quality Grades Resemblance Equalization
Publication -
EDD – Economic Benefit Analysis of Extending Dry Docking Interval
Publication -
Cruise Vessels Air Pollution Inventory for the Port of Kotor
Publication -
K-means clustering for SAT-AIS data analysis
Publication -
Modeling the risk of ship grounding—a literature review from a risk management perspective
Publication -
Reliability of Corroded Stiffened Plate Subjected to Uniaxial Compressive Loading
PublicationThe work is focused on the reliability of corroded stiffened plates subjected to compressive uniaxial load based on the progressive collapse approach as stipulated by the Common Structural Rules for Bulk Carriers and Oil Tankers, employing the limit state design. Two different cases have been investigated. In the first model, the corrosion degradation led to uniform thickness loss, whereas the mechanical properties were unchanged,...
-
Simplified Method of Modelling Behaviour of Ship in Waves with Partially Flooded Compartments
PublicationThis paper contains a description of a numerical model for calculating behaviour of ships in waves. There are many models available, but the one described here can be characterised with a set of parameters that have a decisive impact on the final values of roll motion amplitude and frequency. In this paper, it is shown how a fitting of a standard-shape hull characterised by certain readily available parameters affects...