Search results for: Carbonization temperature

• Pulsed UV-irradiated Graphene Sensors for Ethanol Detection at Room Temperature

  Publication

  • K. Drozdowska
  • A. Rehman
  • P. Sai
  • B. Stonio
  • A. Krajewska
  • G. Cywiński
  • M. Haras
  • S. Rumyantsev
  • J. Smulko
  • A. Kwiatkowski

  - Year 2021

  A graphene-based gas sensor fabricated in a FET (GFET) configuration and its sensitivity towards ethanol and methane is reported. Detection of ethanol at the level of 100 ppm was observed under pulsed UV irradiation and after cleaning by UV light in the N2 ambient. Reduction of the frequency of UV irradiation pulses resulted in increased changes in sensor resistance in the presence of ethanol. Improved sensing behavior was ascribed...

  Full text available to download

• Signal filtering method of the fast-varying diesel exhaust gas temperature

  Publication

  • P. Puzdrowska

  - Combustion Engines - Year 2018

  The paper presents the problem of the impact of external distortions originating on laboratory test stands on the results of measurements of fast-varying diesel exhaust gas temperature. It has been stressed how significant the aspect of the test stand adaptation is during an experiment to ensure the smallest possible impact. This paper, however, focuses on the methods of mathematical processing of a signal recorded during experimental...

  Full text available to download

• Influence of the low ambient temperature on the start-up process of hydraulic pumps

  Publication

  • R. Jasiński

  - Year 2019

  Starting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...

• Low-Temperature Requirements for Bitumen in Central East European Road Construction

  Publication

  • P. Radziszewski
  • M. Sarnowski
  • J. Król
  • P. Pokorski
  • P. Jaskuła
  • D. Ryś
  • M. Pszczoła

  - Baltic Journal of Road and Bridge Engineering - Year 2019

  The paper presents the proposition of special assessment of lowtemperature requirements for bitumens in the region of Central and Eastern Europe where there is a moderate transitional area from sea to the continental type of climate. The results of the research program conducted on the road neat bitumens, Styrene-Butadiene-Styrene polymer and polymer-rubber modified bitumen, and multigrade bitumen types were presented and discussed....

  Full text available to download

• Theoretical study of thermofrictional oscillations due to negative friction-temperature characteristic

  Publication

  • O. Nosko
  • T. Nagamine
  • H. Mori
  • Y. Sato

  - TRIBOLOGY INTERNATIONAL - Year 2013

  Analytical study on oscillations of a body on a moving counterbody has been done by assuming imperfect frictional thermal contact and friction that decreases with contact temperature. It has been shown that stick-slip oscillation occurs due to decrease of friction coefficient when the body moves in the opposite direction to the counterbody. Dynamical characteristics, such as conditions for stable sliding and limit cycles, have...

  Full text to download in external service

• Analytical Study of Sliding Instability due to Velocity- and Temperature-Dependent Friction

  Publication

  • O. Nosko

  - TRIBOLOGY LETTERS - Year 2016

  The instability of sliding causes deterioration of performance characteristics of tribosystems and is undesired. To predict its occurrence, the motion of a body of a one-degree-of-freedom system with friction is investigated about the steady sliding equilibrium position. The motion equation is formulated with the friction coefficient dependent on the sliding velocity and contact temperature changing due to transient heat conduction...

  Full text to download in external service

• Low temperature broad band dielectric spectroscopy of multiferroic Bi6Fe2Ti3O18 ceramics

  Publication

  • A. Lisińska-Czekaj
  • M. Rerak
  • D. Czekaj
  • M. Lubina
  • B. Garbarz-Glos
  • W. Bąk

  - ARCHIVES OF METALLURGY AND MATERIALS - Year 2019

  In the present research the tool of broadband dielectric spectroscopy was utilized to characterize dielectric behavior of Bi6Fe2Ti3O18 (BFTO) Aurivillius-type multiferroic ceramics. Dielectric response of BFTO ceramics was studied in the frequency domain (Δν=0.1Hz – 10MHz) within the temperature range ΔT=-100°C – 200°C. The Kramers-Kronig data validation test was employed to validate the impedance data measurements and it was found...

  Full text available to download

• Ultrafast high-temperature sintering (UHS) of cerium oxide-based compound

  Publication

  • A. Kabir
  • B. Lemieszek
  • J. Karczewski
  • E. De Bona
  • M. Varenik
  • S. Molin
  • M. Biesuz

  - Open Ceramics - Year 2024

  Ultrafast high-temperature sintering (UHS) is an innovative sintering technique that can densify ceramics in a few seconds, dramatically reducing the carbon footprint and firing costs. In this work, the feasibility of applying UHS in Gd-doped ceria (GDC) and GDC-Er-stabilized bismuth oxide (ESB) composite powders was investigated. At high UHS currents (22-24 A), a fully dense GDC sample with a large grain size was obtained. Nonetheless,...

  Full text available to download

• Experimental and Numerical Investigations of the Effect of Curing Conditions on the Temperature Rise of Concrete

  Publication

  • A. Kuryłowicz-Cudowska

  - International Journal of Civil Engineering - Year 2024

  This paper presents experimental and numerical studies investigating the impact of three curing conditions on temperature evolution in concrete cubes. The tests were performed on samples of the same volume (3.375 dm3) under different curing conditions: room temperature, insulation boxes, and adiabatic calorimeter. Various cements (Portland cement, Portland composite cement, and blast furnace slag cement) and aggregates (gravel...

  Full text available to download

• The effect of elevated temperature on LCF damage growth in 2024AA – Experiment and modeling

  Publication

  • A. Falkowska
  • A. Tomczyk
  • A. Seweryn

  - ENGINEERING FAILURE ANALYSIS - Year 2024

  This paper presents the results of experimental low-cycle fatigue (LCF) tests conducted on EN-AW 2024 alloy in T3511 temper at 100 ◦C, 200 ◦C and 300 ◦C. The material’s basic fatigue characteristics were determined, such as fatigue life curve and cyclic strain curve. Both the hysteresis loop and nature of fracture surfaces obtained in macro- and microscopic observations (scanning electron microscope, SEM) were accounted for. The...

  Full text to download in external service

• Modelling of temperature field of flat boiling section with active single nucleation site

  Publication

  • J. Cieśliński
  • R. Jasiński
  • J. Polewski

  - Turbulence : International Journal - Year 2007

  Zaprezentowano główne założenia wybranych modeli wrzenia dla pojedynczego centrum nukleacji. Przedstawiony model numeryczny dotyczy zagadnienia dwuwymiarowego, osiowo-symetrycznego, nieizotropowego przewodzenia ciepła dla warunków brzegowych pierwszego, drugiego i trzeciego rodzaju. Warunek brzegowy drugiego rodzaju reprezentuje gęstość strumienia ciepła połączoną z generacją pęcherzy z pojedynczego centrum nukleacji.

• Materiały zmiennofazowe do stabilizowania temperatury nawierzchni asfaltowych

  Publication

  • P. Wcisło-Kucharek
  • M. Ryms
  • W. Lewandowski
  • E. Klugmann-Radziemska

  - Drogownictwo - Year 2015

  W artykule przedstawiono możliwość wykorzystania lekkiego kruszywa budowlanego modyfikowanego materiałem zmiennofazowym (PCM), jako dodatku do nawierzchni asfaltowej, w celu zwiększenia jej stabilności termicznej przy zachowaniu dotychczasowych właściwości mechanicznych. Cel ten może zostać osiągnięty przez nasączenie porowatych granulek lekkiego kruszywa odpowiednim materiałem zmiennofazowym, co umożliwi magazynowanie określonych...

  Full text to download in external service

• Evaluation of Pavement Temperatures in Poland During Winter Conditions

  Publication

  • M. Pszczoła
  • J. Judycki
  • D. Ryś

  - Transportation Research Procedia - Year 2016

  The paper presents the analysis of pavement temperatures from meteorological stations located at the Polish national roads during the impact of low winter temperatures. Presented issue is particularly important in view of the problem of low-temperature cracks that occur in the asphalt pavement under the influence of low temperatures. For each location of meteorological station there were analysed measurements of the temperature...

  Full text to download in external service

• Characterization of CaWO4 scintillator at room and liquid nitrogen temperatures

  Publication

  • M. Moszyński
  • M. Balcerzyk
  • W. Czarnacki
  • A. Nassalski
  • T. Szczęśniak
  • H. Kraus
  • V. Mikhailik
  • I. Solskii
  • M. Balcerzyk

  - NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION A-ACCELERATORS SPECTROMETERS DETECTORS AND ASSOCIATED EQUIPMENT - Year 2005

  Full text to download in external service

• Study of pure nai at room and liquid nitrogen temperatures

  Publication

  • M. Moszynski
  • M. Balcerzyk
  • W. Czarnacki
  • M. Kapusta
  • W. Klamra
  • P. Schotanus
  • A. Syntfeld
  • M. Szawlowski
  • M. Balcerzyk

  - IEEE TRANSACTIONS ON NUCLEAR SCIENCE - Year 2003

  Full text to download in external service

• Badania mieszanek mineralno-asfaltowych w niskiej temperaturze

  Publication

  • M. Pszczoła
  • J. Judycki

  - Drogownictwo - Year 2013

  W artykule przedstawiono metody badań w niskiej temperaturze betonu asfaltowego przeznaczonego do warstwy ścieralnej. Przedstawione zostały wyniki badań dla 4 różnych metod badawczych: zginania, pełzania, pośredniego rozciągania oraz rozciągania termicznego przy ograniczonym odkształceniu (test TSRST). Próbki betonu asfaltowego były przygotowywane w laboratorium z wykorzystaniem 3 rodzajów asfaltów: asfaltu zwykłego, asfaltu modyfikowanego...

• Zmiany temperatury elementów układu wykonawczego docierarki jednotarczowej

  Publication

  • A. Barylski

  - Mechanik - Year 2013

  Przedstawiono wyniki badań docierania powierzchni płaskich na docierarce jednotarczowej. Praca stanowi wstęp do badań zagadnienia wzrostu temperatury elementów układu wykonawczego obrabiarki. Eksperymenty przeprowadzono na docierarce jednotarczowej ABRALAP 380 przy użyciu kamery termowizyjnej MICRO-EPSILON/TM 160.

  Full text available to download

• Badania temperatury elementów układu wykonawczego docierarki jednotarczowej

  Publication

  • J. Molenda
  • A. Barylski

  - Mechanik - Year 2012

  Przedstawiono wyniki badań własnych wpływu parametrów obróbki na wzrost temperatury docieraka żeliwnego. Badano docieranie powierzchni płaskich na docierarce jednotarczowej. Określono wpływ nacisku jednostkowego i wielkości mikroziaren węglika krzemu i węglika boru na przyrost temperatury maksymalnej po 180 i 300 min. obróbki. Przeprowadzono analizę statystyczną wyników badań i określono współczynniki istotności F.

• Badania temperatury elementów układu wykonawczego docierarki jednotarczowej

  Publication

  • J. Molenda
  • A. Barylski

  - Year 2012

  Przedstawiono wyniki badań własnych wpływu parametrów obróbki na wzrost temperatury docieraka żeliwnego. Badano docieranie powierzchni płaskich na docierarce jednotarczowej. Określono wpływ nacisku jednostkowego i wielkości mikroziaren węglika krzemu i węglika boru na przyrost temperatury maksymalnej po 180 i 300 min. obróbki. Przeprowadzono analizę statystyczną wynikow badań i określono współczynniki istotności F.

• Nadtapianie laserowe biostopu Ti6al4v w niskiej temperaturze

  Publication

  • M. Jażdżewska

  - Year 2005

  Praca prezentuje wstępne wyniki projektu badawczego, dotyczącego modyfikacji powierzchni stopu Ti6al4v laserem dużej mocy w temperaturze ciekłego azotu.

  Full text to download in external service

• Wpływ temperatury austenityzacji na twardość staliwa wysokostopowego.

  Publication

  • M. Głowacka
  • T. Jankowski

  - Year 2004

  Przedstawiono badania mikrostruktury i twardości odlewów ze staliwa wysokochromowego z dodatkami wolframu i wanadu w stanie odlanym, po wyżarzaniu, hartowaniu i odpuszczaniu. Zastosowano trzy temperatury austenityzowania 950, 980 i 1000ºC, pośrednia temperatura zapewniła najwyższą twardość po pełnej obróbce cieplnej badanego staliwa.

• Działanie podzespołów hydraulicznych w niskiej temperaturze otoczenia

  Publication

  • R. Jasiński

  - Year 2005

  W referacie przedstawiono wyniki badań podzespołów hydraulicznych: silników satelitowych SOK, silników orbitalnych, pomp i silników zębatych, rozdzielaczy suwakowych w warunkach szoku termicznego. Stwierdzono, że w warunkach szoku termicznego może dochodzić do nieprawidłowej pracy podzespołów, szczególnie przy dużej różnicy temperatur oleju i podzespołów w chwili początkowej. Badania podzespołów i układów hydraulicznych w tych...

• Pomiar temperatury zeszklenia metodą zmiennotemperaturowej elipsometrii spektroskopowej

  Publication

  • B. Hajduk

  - LAB Laboratoria, Aparatura, Badania - Year 2019

• Influence of selected CO2 absorption promoters on the characteristics of calcium carbonate particles produced by carbonation of the post-distillation liquid from the Solvay process

  Publication

  • N. Czaplicka
  • D. Konopacka-Łyskawa
  • P. Lewandowska
  • M. S. Łapiński
  • R. T. Bray

  - POWDER TECHNOLOGY - Year 2021

  The aim of this work is to compare the effect of selected process parameters, gas flow rate, CO2 absorption promoter concentration and its pKa, on the precipitation of CaCO3 by the gas-liquid method using a model post-distillation liquid from the Solvay process. To ensure effective capture of CO2, the absorption promoters used were ammonia, triethanolamine and triethylamine. The Box-Behnken Design was applied to plan the experiments....

  Full text available to download

• Hard carbon derived from rice husk as low cost negative electrodes in Na-ion batteries

  Publication

  • M. Rybarczyk
  • Y. Li
  • M. Qiao
  • Y. Hu
  • M. Titirici
  • M. Lieder

  - Journal of Energy Chemistry - Year 2019

  Here, we report the synthesis of hard carbon materials (RH) made from natural rice husk through a single pyrolysis process and their application as an anode in sodium-ion batteries. The studies show that the electrochemical properties of RHs are affected by the treatment temperatures, which determine the materials morphology, in particular, their degree of graphitization and extent of continuous channels (nanovoids). The latter...

  Full text to download in external service

• Temperate Phages, Prophages, and Lysogeny

  Publication

  • J. Łoś
  • S. Zielińska
  • A. Krajewska
  • Z. Michalina
  • A. Małachowska
  • K. Kwaśnicka
  • M. Łoś

  - Year 2020

  Full text to download in external service

• Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test

  Publication

  • M. Pszczoła
  • M. Jaczewski
  • D. Ryś
  • P. Jaskuła
  • C. Szydłowski

  - Materials - Year 2018

  Low-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...

  Full text available to download

• The influence of the substrate temperature on the preparation of DNA films for studies under vacuum conditions

  Publication

  • M. Śmiałek-Telega
  • N. C. Jones
  • R. Balog
  • N. J. Mason
  • D. Field

  - EUROPEAN PHYSICAL JOURNAL D - Year 2011

  Experiments were carried out to determine the dependence of the physical form of supercoiled DNA films on the initial temperature of the substrate. Such films are often used in irradiation experiments involving low energy particles, like electrons or photons. In order to obtain absolute values for cross sections for such experiments, the spatial distribution of the sample in the film has to be well estimated. These investigations...

  Full text to download in external service

• The effect of high pressure and subzero temperature on gelation of washed cod and salmon meat

  Publication

  • E. Malinowska-Pańczyk
  • I. Kołodziejska

  - FOOD TECHNOLOGY AND BIOTECHNOLOGY - Year 2017

  The objective of the present work is to examine the infl uence of pressure up to 193 MPa at subzero temperature (without freezing of water) on myofi brillar proteins of salmon and cod meat and on the properties of gels obtained from washed mince of these fi sh. The solubility of proteins from myofi brils of cod and salmon meat suspended in 100 mM KCl solution increased aft er treating the samples with pressure above 60 MPa. The...

  Full text available to download

• Management of low-temperature heat source by ORC aided by additional heat source

  Publication

  • D. Mikielewicz
  • J. Wajs
  • M. Bajor
  • E. Żmuda

  - Year 2015

  The presented work is aimed at utilisation of waste heat in the manner to produce electricity in ORC installation. Therefore the precondition of the study was to use the waste heat available in the form of a stream of hot water at 90°C. Such low enthalpy heat source is rather insufficient to produce a good quality vapour to feed the ORC turbine. That was the incentive to search for the ways of increasing the temperature of the...

• Recuperator with microjet technology as a proposal for heat recovery from low-temperature sources

  Publication

  • J. Wajs
  • D. Mikielewicz
  • E. Fornalik-Wajs
  • M. Bajor

  - Archives of Thermodynamics - Year 2015

  A tendency to increase the importance of so called dispersed generation, based on the local energy sources and the working systems uti- lizing both the fossil fuels and the renewable energy resources is observed nowadays. Generation of electricity on industrial or domestic scale together with production of heat can be obtained for example through employment of the ORC systems. It is mentioned in the EU directive 2012/27/EU for...

  Full text available to download

• Determination of chlorine concentration using single temperature modulated semiconductor gas sensor

  Publication

  • Ł. Woźniak
  • P. Kalinowski
  • G. Jasiński
  • P. Jasiński

  - Year 2016

  A periodic temperature modulation using sinusoidal heater voltage was applied to a commercial SnO2 semiconductor gas sensor. Resulting resistance response of the sensor was analyzed using a feature extraction method based on Fast Fourier Transformation (FFT). The amplitudes of the higher harmonics of the FFT from the dynamic nonlinear responses of measured gas were further utilized as an input for Artificial Neural...

  Full text to download in external service

• Influence of Bitumen Type and Asphalt Mixture Composition on Low-temperature Strength Properties

  Publication

  • M. Pszczola
  • C. Szydlowski
  • M. Pszczoła

  - Year 2018

  Full text to download in external service

• Spatial and interannual variations of seasonal sea surface temperature patterns in the Baltic Sea

  Publication

  • K. Bradtke
  • A. Herman
  • J. Urbański

  - OCEANOLOGIA - Year 2010

  Full text to download in external service

• <title>Modeling of noncontact temperature measurement system using multiwavelength pyrometry</title>

  Publication

  • A. Mazikowski
  • R. Hypszer
  • M. Jedrzejewska-Szczerska

  - Year 2001

  Full text to download in external service

• Influence of yttria surface modification on high temperature corrosion of porous Ni22Cr alloy

  Publication

  • J. Karczewski
  • K. Dunst
  • P. Jasiński
  • S. Molin

  - International Journal of Applied Ceramic Technology - Year 2018

  Protective coatings for porous alloys for high temperature use are relatively new materials. Their main drawback is high temperature corrosion. In this work protective coatings based the on Y-precursor infiltrated into the sintered Ni22Cr alloys are studied at 700°C. Effects of the amount of the protective phase on the resulting corrosion properties are evaluated in air and humidified hydrogen. Weight gain of the samples, their...

  Full text to download in external service

• Moisture content during and after high- and normal-temperature drying processes of wood

  Publication

  • J. Barański

  - DRYING TECHNOLOGY - Year 2018

  The aim of the article is to present the results of moisture content of wood during and after the high-temperature steam and air–steam mixture drying processes and after an open air-drying process. The knowledge of moisture content changes of wood in the process of its drying is one of the important parameters to economy drying process and to keep the quality of dried wood. Wood samples, namely, spruce (Picea abies K.) and beech...

• APPLICATION OF SATELLITE IMAGERY AND GIS TOOLS FOR LAND SURFACE TEMPERATURE ESTIMATION AND VERIFICATION

  Publication

  • A. Chybicki
  • Z. Łubniewski
  • J. Niedzielko
  • D. Ruciński

  - HYDROACOUSTICS - Year 2013

  Land surface temperature (LST) plays an important role in many land-surface processes on regional as well on global scales. It is also a good indicator of energy flux phenomena and is used as a parameter in various Earth observation related studies. However, LST estimation based on processing and utilisation of satellite derived data constitutes several problems in terms of time limitations, accessibility, atmospheric influence...

  Full text available to download

• The influence of temperature on properties of the polymer flexible joint used for strengthening historical masonries

  Publication

  • T. Falborski
  • A. Kwiecień
  • M. Strankowski
  • Ł. Piszczyk
  • R. Jankowski

  - Wiadomości Konserwatorskie - Year 2012

  A new method of repairing damaged structures by filling the cracks with a specially prepared elastomeric polymer mass has been recently proposed. This new and innovative technique, known as the Flexible Joint Method (FJM), is mainly dedicated to masonries and historical objects, where minimum intervention is permitted. The flexible joint bonds the disrupted elements and ensures further safe exploitation of a damaged structure....

  Full text to download in external service

• Influence of geometry and annealing temperature in argon atmosphere of TiO2 nanotubes on their electrochemical properties

  Publication

  • M. Nycz
  • E. Paradowska
  • K. Arkusz
  • D. Pijanowska

  - Acta of Bioengineering and Biomechanics - Year 2020

  Full text to download in external service

• High-Energy-Low-Temperature Technologies for the Synthesis of Nanoparticles: Microwaves and High Pressure

  Publication

  • W. Lojkowski
  • C. Leonelli
  • T. Chudoba
  • J. Wojnarowicz
  • A. Majcher
  • A. Mazurkiewicz

  - Inorganics - Year 2014

  Full text to download in external service

• Comparison of commercial thermoluminescent readers regarding high-dose high-temperature measurements

  Publication

  • P. Bilski
  • W. Gieszczyk
  • B. Obryk
  • K. Hodyr

  - RADIATION MEASUREMENTS - Year 2014

  Full text to download in external service

• TEMPERATURE AND RELATIVE HUMIDITY CONTROL IN MASS AND DECAY PREVENTION IN POSTHARVEST HANDLING OF PEACHES

  Publication

  • G. Lysiak
  • W. Florkowski
  • S. Prussia

  - Acta Horticulturae - Year 2003

  Full text to download in external service

• Cointegration approach for temperature effect compensation in Lamb-wave-based damage detection

  Publication

  • P. Dao
  • W. Staszewski
  • P. B. Dao

  - SMART MATERIALS & STRUCTURES - Year 2013

  Full text to download in external service

• P3HT:PCBM blend films phase diagram on the base of variable-temperature spectroscopic ellipsometry

  Publication

  • B. Hajduk
  • H. Bednarski
  • B. Jarząbek
  • H. Janeczek
  • P. Nitschke

  - Beilstein Journal of Nanotechnology - Year 2018

  Full text to download in external service

• Phase diagram of P3HT:PC70BM thin films based on variable-temperature spectroscopic ellipsometry

  Publication

  • B. Hajduk
  • H. Bednarski
  • B. Jarząbek
  • P. Nitschke
  • H. Janeczek
  • B. Hajduk

  - POLYMER TESTING - Year 2020

  Full text to download in external service

• Processing of polymer‐derived, aerogel‐filled, SiC foams for high‐temperature insulation

  Publication

  • A. Zambotti
  • E. Ionescu
  • N. Gargiulo
  • D. Caputo
  • C. Vakifahmetoglu
  • B. Santhosh
  • M. Biesuz
  • G. Sorarù

  - JOURNAL OF THE AMERICAN CERAMIC SOCIETY - Year 2023

  Full text to download in external service

• Sea surface temperature distribution during upwelling along the Polish Baltic coast

  Publication

  • A. Krężel
  • M. Szymelfenig
  • M. Ostrowski

  - OCEANOLOGIA - Year 2005

  Among over 150 maps of sea surface temperature in the Polish Baltic coastal region derived from satellite data during the warm period of the year (April-October) in 2000-2002, 41 cases were noted where its distribution showed characteristic features indicating the occurrence of coastal upwelling. The fundamental parameters of range, probability of occurrence and temperature modification caused by water from deeper sea layers...

  Full text to download in external service

• Room‐Temperature Multiferroicity and Magnetization Dynamics in Fe/BTO/LSMO Tunnel Junction

  Publication

  • J. Pawlak
  • W. Skowroński
  • A. Żywczak
  • M. Przybylski

  - Advanced Electronic Materials - Year 2021

  Full text to download in external service

• Luminescence quenching in KYb(WO4)2-Tb3+: An example of temperature-pressure equivalence

  Publication

  • S. Mahlik
  • F. Diaz
  • P. Boutinaud

  - Journal of Luminescence - Year 2017

  Full text to download in external service