Filters
total: 2162
filtered: 1232
displaying 1000 best results Help
Search results for: sacrifice zones
-
Study of structures and properties of the laser cladding exhaust valve after service
PublicationPrzylgnie zaworów wydechowych silnie obciążonego silnika okrętowego zostały pokryte warstwą wykonana ze stopu kobaltu za pomocą techniki napawania laserowego. Tak przygotowane zawory były eksploatowane przez 3000 godzin w silniku Daru Młodzieży. Po tym czasie zostały zdemontowane i poddane szczegółowej analizie. Warunki pracy spowodowały powstanie na powierzchni przylgni warstwy tlenków o różnej grubości, wykazującej skłonność...
-
The use of can in automation test bench to test the engine cooling system
PublicationW publikacji opisano zasady rejestracji danych pomiarowych w hamowni silnikowej do badań układów chłodzenia silników samochodowych. Założeniami projektu stanowiska było użycie standardu przesyłu danych typu CAN. Opracowano metodę dużej gęstości zapisu przesyłanych danych.
-
Dependence of the toxic components exhaust emission from the car engine starting temperature
PublicationW publikacji opisano wyniki badań empirycznych zależności stężeń toksycznych składników spalin od stanu cieplnego silnika w chwili rozruchu. Zwrócono uwagę na duże stężenia w pierwszych kilkudziesięciu sekundach po rozruchu. Badano silniki samochodów osobowych zarówno w eksploatacji jak i na hamowni podwoziowej.
-
Some problems with operation of engines fueled with landfill biogas
PublicationW referacie przedstawiono wybrane problemy związane z eksploatacją tłokowych silników spalinowych zasilanych biogazem pozyskiwanym z wysypiska śmieci. Biogaz wysypiskowy charakteryzuje się znaczną zmiennością zawartości metanu, co ma istostny wpływ na pracę silników zasilanych tym paliwem. W referacie przedstawiono wyniki badań przeprowadzonych na wysypisku śmieci, w wyniku których zaprezentowano zrówno wielkość zmian zawartości...
-
The Influence of Abrasive Machine on Temperature During One Side Lapping
PublicationPrzedstawiono wyniki badań temperatury układu wykonawczego docierarki jednotarczowej. Analizowano temperaturę trzech pierścieni prowadzących separatory przy wykorzystaniu kamery termograficznej V-20 II firmy VIGO System S.A.
-
The influence of plastic working on the selection properties of the nickel - aluminium alloy coatings = Wpływ obróbki plastycznej na wybrane właściwości powłok stopowych nikiel - aluminium
PublicationW pracy przedstawiono wyniki badań nad możliwością zastosowania technologii obróbki plastycznej (walcowania na zimno i gorąco, oraz prasowania) do kształtowania wybranych właściwości natryskiwanych płomieniowo powłok stopowych Ni-5%Al o strukturze jednofazowej, a mianowicie granicznego roztworu stałego , o maksymalnej 10% rozpuszczalności glinu w sieci krystalograficznej niklu. Celem pracy jest wstępna analiza możliwości zastąpienia...
-
Effect of tungsten content on the corrosion resisntance of the cobalt base PTA cladding layers = Wpływ zawartości wolframu w stopach kobaltu na odporność korozyjną warstw napawanych plazmowo
PublicationBadaniom poddano napawane plazmowo warstwy wytworzone na powierzchni przylgni zaworów wylotowych silnie obciążonych silników Diesla stosowanych w okrętownictwie. Jako materiał do napawania zastosowano trzy rodzaje proszków wykonanych ze stopów na bazie kobaltu i chromu zawierających różne ilości wolframu ( 4.9, 5.3 i 9 % masowych). Wykonane napoiny wielowarstwowe po odpowiednim przygotowaniu poddano działaniu podwyższonej temperatury...
-
Stochastic model of the load spectrum for main engines of sea-going ships
PublicationW artykule przedstawiono możliwość zastosowania procesów semimarkowskich do probabilistycznego opisu widma obciążeń silników o zapłonie samoczynnym, zastosowanych do napędu statków - czyli silników głównych. W rozważaniach uwzględnione zostały charakterystyki zewnętrzne mocy tego rodzaju silników. Umożliwiły one sformułowanie czteroelementowego zbioru stanów procesu obciążeń tego rodzaju silników. Do opisu rzeczywistego procesu...
-
Concept for interpretation and assessment of slide bearings operation in Diesel enfines in probabilistic approach
PublicationW artykule zaproponowano interpretację wartościującą działania, które (podobnie jak przedstawione w mechanice klasycznej działania Hamiltona i Maupertiusa oraz działanie wynikające ze zmiany pędu ciała) jest rozpatrywane jako wielkość fizyczna o jednostce miary zwanej''dżulosekundą''. Przedstawiono propozycję ilościowej interpretacji działania dowolnego poprzecznego łożyska ślizgowego, w którym zachodzą oddziaływania energetyczne...
-
Energy-time method for assesment of main diesel engine operation
PublicationW publikacji przedstawiono rozwinięcie prezentowanej w literaturze metody ilościowej oceny działania na przykładzie okrętowego silnika głównego z zapłonem samoczynnym. Według tej interpretacji, działanie silnika może zostać przedstawione jako wielkość fizyczna. W tym aspekcie, na przykładzie wybranego układu funkcjonalnego, silnika dokonano oceny przydatności tej wielkości do opisu własności niezawodnościowych tego układu.
-
Lubricity-based estimation of the changes in the brake fluid quality
PublicationW artykule przedstawiono, na podstawie wyników badań laboratoryjnych, możliwość określenia wartości smarności łączącej własności fizykochemiczne i reologiczne płynów. Smarność, która została określona dla trzech płynów hamulcowych (oznaczenia zastrzeżone przez firmę zlecającą porównanie ich własności), umożliwiła wybór najlepszego, który pewnie zostanie zastosowany w instalacjach hamulcowych samochodów.
-
Selected problems of experimental investigation of dynamically loaded journal bearings
PublicationIn the paper some problems concerning relations between external bearing loadings and critical lining stresses are described for test stand with rotating load vector. According to the standard ISO 7905/1 this type of test stand, for dynamically loaded slide bearing, is recommended as a basic research unit for material testing in a complete bearing unit. The lining stress calculation results occurred being dependent on applied calculation...
-
Some problems of slide bearing material fatigue evaluation.
PublicationA slide bearing alloy resistance against fatigue failures have been investigated for three different lubricants, different heat loadings and different stress ratio κ values. The research methods and data handling procedures for determination of particular parameter effects on fatigue strength have been described and analysed for experiments that were set and performed in laboratory tester SKMR-2. Main and interaction effects of...
-
Fatigue resistance investigation of the IC engine MB11 bearings, working under conditions of dynamic unidirectional loadings
PublicationThe slide bearing material MB11 fatigue resistance has been investigated with the application of SMOK - test stand in which dynamic unidirectional loadings to the test bearing is generated. Slide bearing layer consists of the bronze MB11 ( Cu Pb22 Sn 3 ) sintered to the steel shell. Each of the tested bearing has been subject to the standard 20-hour test, under conditions of the full fluid lubrication. Methodology of the experiments,...
-
Gas corrosion influence on the exhaust valve face of the marine engine = Wpływ korozji gazowej na stan przylgni zaworów wylotowych silnika okrętowego
PublicationIstotnym czynnikiem wpływającym na poprawność funkcjonowania silnika okrętowego jest szczelność zaworów. Szczególnie w odniesieniu do zaworów wylotowych brak szczelności prowadzi do pogorszenie warunków spalania a przede wszystkim do przyspieszonego zniszczenia zawory poprzez uszkodzenia przylgni.Przylgnia grzybka zaworowego współpracuje z przylgnią gniazda zaworowego tworząc cykliczny szczelny kontakt stykowy w trakcie pracy silnika....
-
Arch bridges under test loadings
PublicationThis paper illustrates experience in arch bridges test loadings of the research team of Department of Structural Mechanics and Bridge Structures from the Gdansk University of Technology. The presented calculations results constist the analysis of spatial construction schemes made using the finite elements method (FEM) and its comparison to the field studies. Arch bridges with the longest spans, visualisation of the computational...
-
Rozwiązania konstrukcyjne układów chłodzenia cieczą silników tłokowych
PublicationW artykule przedstawiono różne rozwiązania konstrukcyjne układów chłodzenia tłokowych silników spalinowych. Szczególną uwagę poświęcono sposobom chłodzenia cylindrów. Zwrócono uwagę na możliwości sterowania parametrami pracy układów.
-
Transport system integration - a challenge of our times
PublicationKażdego dnia w systemie transportowym na świecie ginie ponad 3 tys. osób, z czego większość w wypadkach drogowych. W Polsce, podobnie jak w innych krajach UE, obserwuje się podobne dysproporcje pomiędzy skalą wypadków drogowych i wypadków w innych rodzajach transportu. Z punktu widzenia zarządzania bezpieczeństwem, każdy z systemów gałęziowych jest zorganizowany w inny sposób. Dotyczy to baz danych, instytucji zarządzających infrastrukturą...
-
The resistance investigation of the marine engine exchaust valve using the modelling chamber = Badania odporności zaworów wylotowych silnika okrętowego w komorze modelowej
PublicationWe współczesnej technice szereg części urządzeń i instalacji pracuje w długich okresach czasu i w złożonych warunkach obciążenia mechanicznego, termicznego i chemicznego. Próby wprowadzenia nowych rozwiązań technicznych muszą być poprzedzone szczegółowymi badaniami, które stwierdzą przydatność do konkretnych zastosowań. Problemem występującym w przemyśle okrętowym, a dokładniej w procesie eksploatacji silników okrętowych jest trwałość...
-
Możliwości zmniejszenia mocy potrzebnej do napędu pompy cieczy chłodzącej silnika samochodowego
PublicationW artykule opisano wybrane problemy napędu pompy cieczy chłodzącej silnika samochodowego. W tradycyjnych układach chłodzenia wydajność pompy jest zbyt duża przy wysokich prędkościach obrotowych silnika. Mierząc temperaturę tulei cylindrowych autor proponuje obniżenie wydajności pompy dla zmniejszenia mocy potrzebnej do jej napędu.
-
Uwagi o adekwatności warunków testów emisyjnych ISO 8178 w odniesieniu do rzeczywistych warunków eksploatacji silników okrętowych
PublicationW referacie przedstawiono ogólną charakterystykę testów badawczych NOx silników jednostek pływających, ocenę trudności realizacji cykli badawczych silników głównych napędzających śrubę o skoku ustalonym podczas morskich prób zdawczych a także uwagi i ocenę adekwatności obciążeń zalecanych poszczególnymi testami w stosunku do obciążeń występujących podczas eksploatacji statków różnych typów.
-
Conception of valuation of combustion engine operation
PublicationW artykule zaproponowano interpretację wartościującą działania, które jest przyrównane do wielkości fizycznej o jednostce miary zwanej dżulosekundą, podobnie jak przedstawione w mechanice klasycznej działania Hamiltona i Maupertiusa. Działanie w tym ujęciu rozpatrywane jest także w mechanice kwantowej, w odniesieniu do żródła promieniowania elektromagnetycznego ciała, którego działanie charakteryzuje stała Planca. Przedstawiono...
-
Możliwości parametrycznej identyfikacji warunków eksploatacji pojazdu samochodowego
PublicationW pracy zaprezentowana została nowa metoda parametrycznej identyfikacji warunków eksploatacji pojazdu samochodowego. Warunki eksploatacji pojazdu identyfikowane będą za pomocą parametru, który obejmuje zarówno wpływ warunków zewnętrznych jak również styl jazdy kierowcy. Ilość energii mechanicznej przekazywanej kołom napędowym w czasie cyklu pomiarowego może wynikać w równym stopniu z zaistniałych warunków ruchu pojazdów, co ze...
-
Isotropic damage in viscoplastic flow conditions, fem applications with practical examples
PublicationW pracy omówiono niektóre zagadnienia zniszczenia w warunkach płynięcia lepkoplastycznego. Podano podstawowe prawa konstytutywne jakie mogą tu być zastosowane oraz sposoby identyfikacji parametrów materiałowych. Pokazano przykład zastosowania.
-
Wstępna ocena wpływu niektórych parametrów docierania na wzrost temperatury elementów układu wykonawczego docierarki jednotarczowej
PublicationPrzedstawiono wyniki badań rozpoznawczych procesu docierania w aspekcie wzrostu temperatury elementów układu wykonawczego docierarki jednotarczowej. Temperaturę mierzono zdalnie, wykorzystując kamerę termograficzną serii V-20 II firmy VIGO Sytem SA. Obróbkę prowadzono na docierarce Abralap 380. Analizowano wpływ podstawowych parametrów docierania: czasu, prędkości i nacisków jednostkowych. Docierano stal w stanie miękkim mikroziarnami...
-
Application of the finite element methods in long-term simulation of the multi-physics systems with large transient response differences
PublicationApplication of the Finite Element Method (FEM) and the Multibody Dynamics Method allows analyzing of complex physical systems. Complexity of the system could be related both to the geometry and the physical description of phenomenon. The metod is the excellent tool for analyzing statics or dynamics of the mechanical systems, and permits tracking of Multi Body System (MBS) transient response for the long-term simulations and application...
-
Behavior of the exhaust valve cladding face under the service conditions
PublicationPodczas eksploatacji silnika okrętowego kluczowym problemem jest trwałośc zaworów wylotowych a w szczególności wąskiego fragmentu - przylgni grzybka zaworu, która decyduje o szczelności zaworu.Przylgnia wykonana przez laserowe napawanie stopu kobaltu została poddana badaniom w warunkach normalnej eksploatacji silnika L22 przez 2 lata. W tym czasi silnik był zasilany zarówno paliwem lekkim jak i biopaliwem. Po zdemontowaniu głowicy...
-
Intelligent microbearing project with memory of stress-strain history
PublicationTaking into account the increasing need of intelligent micro-bearing with memory, this paper presents the optimization, simulation and practical application of operating parameters(load carrying capacity, friction forces, friction coefficient, wear), simulation for hydrodynamic HDD micro-bearing with curvilinear nano-grooved journal profile. One of the reason of such journal profile is that this journal profile contributes to the...
-
INFLUENCE OF INLET GEOMETRY ON THE EFFICIENCY OF 1MW STEAM TURBINE
PublicationThe process of the design of the 1MW steam turbine includes designing the stator and rotor blades, the steam turbine inlet and exit, the casing and the rotor. A turbine that operates at rotation speeds other than 3000 rpm requires a gear box and generator with complex electronic software. This paper analyses the efficiency of eight turbine variants, including seven inlet geometries and three stages of stator as well as an eight...
-
INNOVATIVE RUN FLAT SYSTEMS
PublicationOne of the most essential threats to the mobility of wheeled vehicles is their relatively high sensitivity to tire damage. Tires can be damaged as a result at vehicle-targeting fire, after running on a mine or an improvised charge. The purpose of the article is to analyze the current technical solutions in wheeled vehicle tires, allowing for the unobstructed use of the vehicle despite the damage of one or several tires (RUN FLAT...
-
EXPERIMENTAL RESEARCH ON INFLUENCE OF THE FUEL NOZZLE GEOMETRY ON THE FUEL CONSUMPTION OF THE MARINE 4-STROKE DIESEL ENGINE
PublicationThe article presents experimental research that has been carried out on a marine, 4-stroke, 3-cylinder, turbocharged engine. During testing, the engine operated at a constant rotational speed of 750 rpm and a load from 0 kW to 280 kW. The engine was fuelled by diesel oil of known specification and loaded by electric generator with water resistance. The fuel consumption was measured during the engine operation with fuel nozzles...
-
Determining the conditions for temperature measurements during flat lapping
PublicationPrzedstawiono pomiary temperatury układu wykonawczego docierarki jednotarczowej ABRALAP 380. Badano wpływ liczby stosowanych pierścieni prowadzących przy docieraniu elementów ceramicznych mikroziarnami węglika krzemu. Analizowano przyrost temperatury układu w czasie do trzech godzin. W badaniach zastosowano kamerę termowizyjną V-20II firmy VIGO System S.A.
-
Bond graph modeling of the new generation engine cooling systems = Zastosowanie metody grafów wiązań do modelowania nowej generacji układów chłodzenia silników spalinowych
PublicationW referacie szczegółowo opisano modele wymiany ciepła i przepływów w układzie chłodzenia. Metoda grafów wiązań okazała się szczególnie użyteczną dla modelowania skomplikowanych systemów energetycznych o różnych postaciach energii. Jako przykładu użyto obiegu chłodzenia silnika badawczego na hamowni silnikowej.
-
Automated Diagnostics of Current Pick-Up Disturbances in Electric Traction Networks
PublicationThe present work defines the basic causes of bow disturbances of current pick-up, sets a task of establishing a system of automated control of bow disturbances at feeder zones of electric traction networks, proposes structural variants of the technical system implementation, describes the algorithm of detection of bow disturbances of current pick-up.
-
Low-Temperature Requirements for Bitumen in Central East European Road Construction
PublicationThe paper presents the proposition of special assessment of lowtemperature requirements for bitumens in the region of Central and Eastern Europe where there is a moderate transitional area from sea to the continental type of climate. The results of the research program conducted on the road neat bitumens, Styrene-Butadiene-Styrene polymer and polymer-rubber modified bitumen, and multigrade bitumen types were presented and discussed....
-
Game-based Sprint retrospectives: multiple action research
PublicationIn today’s fast-paced world of rapid technological change, software development teams need to constantly revise their work practices. Not surprisingly, regular reflection on how to become more effective is perceived as one of the most important principles of Agile Software Development. Nevertheless, running an effective and enjoyable retrospective meeting is still a challenge in real environments. As reported by several studies,...
-
Settlement of a historic building due to seepage-induced soil deformation
PublicationThe research paper reviews issues associated with the impact of groundwater flow on soil characteristics and parameters, hence, the entire structure of a building set on it. Water seepage through the ground, building subsoil or structural elements of buildings made of soil affects the soil skeleton and may lead to changes in the arrangement of individual grains relative to each other, i.e., a modified soil structure. Soil solid...
-
Role of bead sequence in underwater welding
PublicationThis paper presents examinations of the role of the bead sequence in underwater welding. Two specimens of wet welded layers made by covered electrodes with the use of normalized S355G10+N steel were welded by a reasonable bead sequence. For each specimen, metallographic macro- and micro-scopic tests were done. Then, Vickers HV10 hardness measurements were conducted for each pad weld in the welded layer. The results show that welding...
-
Agile Methods In Formation of Metropolis Neighbourhood
PublicationA study of the zone adjoining the metropolis area of Tricity (Poland) was conducted on the basis of analyses of changes in spatial development, outline planning decisions and local plans of spatial development. Localities placed at several dozen kilometres from strongly urbanized areas do not constitute metropolis outskirts. The vicinity of large urban centres is an obstacle to the development of localities as self-sufficient units...
-
The Effects of Pin Profile on HDPE Thermomechanical Phenomena during FSW
PublicationFriction stir welding (FSW) of polymeric materials has recently attracted significant attention. Herein, we present the effect of the tool pin profile on the FSW of high-density polyethylene (HDPE) joints through joint experimental analysis and thermomechanical simulations. For analysis of pin profile effects on the thermomechanical properties of HDPE joints, frustum (FPT), cubic (CPT), and triangular (TPT) pin shapes were selected...
-
Meso‐scale analyses of size effect in brittle materials using DEM
PublicationThe paper describes numerical meso-scale results of a size effect on strength, brittleness and fracture in brittle materials like concrete. The discrete element method (DEM) was used to simulate the size effect during quasi-static splitting tension with the experimental-based meso-structure. The two-dimensional (2D) calculations were carried out on concrete cylindrical specimens with two diameters wherein two different failure...
-
Towards a global historical emission inventory for selected PCB congeners - a mass balance approach. 3. An update
PublicationPoprzednie prace autorów zawierały bardzo istotne informacje do oceny stężeń związków polychlorobifenylowych (PCB) w rejonach oddalonych od dużych źródeł emisji tych związków jak i w środowisku globalnym. Okazało się, że niezbędna jest modyfikacja emisji PCB po roku 2000. Przedstawiono nowe dane o produkcji PCB w Polsce oraz nowe dane nt. składu chemicznego różnych produktów technicznych opartych na PCB. Ulepszono też metody oceny...
-
Valence and lowest Rydberg electronic states of phenol investigated by synchrotron radiation and theoretical methods
PublicationWe present the experimental high-resolution vacuum ultraviolet (VUV) photoabsorption spectra of phenol covering for the first time the full 4.3–10.8 eV energy-range, with absolute cross sections determined. Theoretical calculations on the vertical excitation energies and oscillator strengths were performed using time-dependent density functional theory and the equation-of-motion coupled cluster method restricted to single and double...
-
Investigation of the 0.4C-35Cr-45Ni-Nb Alloy after Service in High-Temperature Steam and Hydrocarbons Environment
PublicationThe paper presents the results of investigation of the 0.4C-35Cr-45Ni-Nb alloy, which operated in the cracked hydrocarbon feeds and dilution steam at 1125 C. The material originated from the pyrolytic furnace coil tubes, of which internal walls were in contact with the aforementioned medium, whereas the external walls were in contact with the flue gases. The examination included metallographic and mechanical tests on the material...
-
Modelling of heat transfer in supercritical pressure recuperators
PublicationIn the paper presented is analysis of convective flow heat transfer at supercritical pressure in channels of heat exchanger working in the thermodynamic cycle. The modelling is based on the division of the flow into three regions, namely the heavy fluid, a two phase flow consisting of the heavy and light fluids and finally the light fluid flow. Modelling is concentrated on the region of simultaneous flow of two fluids divided into...
-
The Optical Coherence Tomography and Raman Spectroscopy for Sensing of the Bone Demineralization Process
PublicationThe presented research was intended to seek new optical methods to investigate the demineralization process of bones. Optical examination of the bone condition could facilitate clinical trials and improve the safety of patients. The authors used a set of complementary methods: polarization-sensitive optical coherence tomography (PS-OCT) and Raman spectroscopy. Chicken bone samples were used in this research. To stimulate in laboratory...
-
Metallurgical characterization and high-temperature tensile failure of Inconel 617 alloy welded by GTAW and SMAW—a comparative study
PublicationTwo types of the weld joint of Inconel 617 alloy were produced using gas tungsten arc welding (GTAW) and shielded metal arc welding (SMAW) processes with ERNiCrCoMo-1 filler metal and ENiCrCoMo-1 electrode, respectively. The weld metal showed the segregation of the principle alloying elements like Mo and Cr along the inter-dendritic spaces, triggering the formation of secondary phases. The microstructure characterization of the...
-
Comparative modeling of shear localization in granular bodies with FEM and DEM
PublicationThe intention of the paper is to compare the calculations of shear zones in granular bodies using two different approaches: a continuum and a discrete one. In the first case, the FEM based on a micro-polar hypoplastic constitutive law was used. In the second case, the DEM was taken advantage of, where contact moments were taken into account to model grain roughness. The comparative calculations were performed for a passive case...
-
Behaviour of orthotropic surgical implant in hernia repair due to the material orientation and abdomen surface deformation
Publicationrelation to the different range of typical deformations observed in different directions and zones of abdomen surface due to the patients’ life activities, has a significant influence on the extreme junction forces in the mesh–tissue connections and hence the repair persistence. The finite element model of the orthotropic implant was developed, and the junction forces in the connections of tissue and mesh were studied. The kinematical...
-
The allergic and irritating reactions to metallic implants with trauma - orthopaedic patients
PublicationThe article presents the analysis of clinical operation complications after the treatment of long bones by mean of ostheosynthesis with the use of metal implants and endoprothesoplastic of hip joints.