Filters
total: 1627
filtered: 1440
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: POLIMERY FLUOROWE
-
Fabrication of toughened plastic using styrene butadiene rubber-poly (methyl methacrylate) interpenetrating polymer networks
PublicationA standard set of interpenetrating polymeric networks (IPNs) has been contrived using an elastomerstyrene butadiene rubber and a thermoplastic poly (methyl methacrylate) through sequential polymerization protocol. This low-cost material can be hopefully engaged as a toughened plastic with cocontinuous morphology. Different morphological protocols including Raman imaging are effectively utilized to envisage the effect of blend ratio...
-
Dielectric Properties of BiNbO<sub>4</sub>-Based Ceramic-Polymer Composites with 0-3 Connectivity
PublicationIn the present study two-phase BiNbO4//PVDF composites with 0-3 connectivity were studied by impedance spectroscopy within the frequency range Δν=100Hz-1MHz at room temperature. Polyvinylidene fluoride (PVDF) acted as a matrix whereas bismuth niobate (BiNbO4) powder acted as a dispersed phase. The volume fraction of the ceramic phase was cV=2, 4, 6, 8, 10, 16 and 20vol%. Analysis of the impedance data registered for composites...
-
Excitation energy transfer in partly ordered polymer films differing in donor and acceptor transition moments orientation
PublicationBased on spectroscopic measurements selected properties of nonradiative Förster energy transport are studied in uniaxially stretched polyvinyl alcohol thin films for three systems differing in donor and acceptor transition moments orientation relative to the axis of stretching. In particular, donor – acceptor emission anisotropy spectra yield completely different regularities for these systems in uniaxially stretched films, whereas...
-
Synthesis and photoelectrochemical behaviour of hydrogenated titania nanotubes modified with conducting polymer infiltrated by redox active network
PublicationIn this work, we show preparation of ordered inorganic-organic composite electrode material where hydrogenated titania nanotubes H-TiO2 with tubularly developed surface modified with poly(3,4-ethylenedioxythiophene) matrix permeated by Prussian Blue (PB) inorganic redox network in order to reach highly photoactive heterojunction. The polymer deposition was realized via two subsequent processes covering: i) potentiostatic polymerization...
-
Electroactive polymer/graphene oxide nanostructured composites; evidence for direct chemical interactions between PEDOT and GOx
PublicationThis work concerns electrochemical synthesis of nanocomposites consisting of conducting polymer and reduced graphene oxide (rGOx) as electrode materials for supercapacitors. The electrosynthesis was performed in an aqueous solution of the 3,4-ethylenedioxytiophene (EDOT) monomer and graphene oxide (GOx) without supporting electrolyte. The amount of GOx was optimized to obtain the best electrochemical performance of the nanocomposite...
-
Characterization of various drinking waters by new potentiometric taste sensor with lipid, lipid-like polymer membranes
PublicationA new sensing system comprising five all-solid-state electrodes with lipid, lipid like-polymer membranes was applied for rapid qualitative and quantitative analysis of various drinking waters. The results elaborated by chemometric methods revealed sensitivity to CO2 content in drinking water, suggesting that this sensing system could be used as a taste sensor. The ability of taste sensor to perform quantitative analysis of minerals...
-
Evaluation of apparent Young׳s modulus of the composite polymer layers used as sliding surfaces in hydrodynamic thrust bearings
PublicationHydrodynamic bearings with a polymer sliding layer are able to operate in severe conditions, mainly due to favorable properties of the polymers. The goal of this research was to evaluate apparent Young׳s modulus of two types of the polymer composite layers used for sliding surfaces in hydrodynamic bearings, as a function of temperature. The Young׳s modulus was evaluated on the basis of compression tests carried out on samples obtained...
-
New bioactive polymer filtering material composed of nonwoven polypropylene containing alkylammonium microbiocides on a perlite carrier
Publication -
Reactions of solute species at an electrode modified with titanocene functionalized polypyrrole film: ferrocene and titanocene dichloride
PublicationPo raz pierwszy zbadano możliwość intermediacji ładunku poprzez centra tytanocenowe polimeru modyfikowanego chemicznie związanymi grupami dichloro tytanocenowymido polipirolu. Badano reakcje elektrodowe ferrocenu i dichlorotytanocenu. Wykazano aktywność elektrodową w zakresie potencjałów redoks pary Ti(IV/TiIII)w stosunku do reakcji redoks ferrocenu i reakcji dichlorotytanocenu. Wykazano, że centra TcCl2 polimeru są zadowalająco...
-
Jadalne folie oraz powłoki powierzchniowe z polimerów naturalnych stosowane do opakowań żywności. Część 1. Właściwości
PublicationArtykuł stanowi przegląd literatury dotyczącej wykorzystania polimerów naturalnych (białek i polisacharydów) do wytwarzania jadalnych powłok powierzchniowych bądź opakowań artykułów żywnościowych. Omówiono ich właściwości ze szczególnym uwzględnieniem przepuszczalności pary wodnej oraz wymagania stawiane takim materiałom. Przedstawiono sposoby modyfikacji folii z polimerów naturalnych poprzez włączenie w ich struktury substancji...
-
Jadalne folie oraz powłoki powierzchniowe z polimerów naturalnych stosowane do opakowań żywności. Część 2. Modyfikacje
PublicationArtykuł jest kontynuacją przeglądu literatury dotyczącego jadalnych opakowań żywności wytwarzanych z polimerów naturalnych (białek lub polisacharydów). Przedstawiono różne rodzaje modyfikacji na drodze sieciowania (fizycznego, chemicznego i enzymatycznego) folii opakowaniowych uzyskanych z takich materiałów.
-
Assessing ecotoxicity, synergic and antagonistic actions of commonly used components of polymerization mixture in molecularly imprinted polymers preparation process
PublicationIncreasingly, the challenge is the optimal process of developing a suitable MIP-type sorptive material (taking into account its final form and application area), which is mainly related to the efficiency/effectiveness of the polymerization process. The lack of reaction or its low efficiency generates additional waste and puts it into the environmental cycle. The main aim of the performed research was the estimation of ecotoxicity,...
-
Electrochemical synthesis of 2D copper coordination-polymers: Layer-stacking deviation induced by the solvent and its effect on the adsorptive properties
PublicationA 2D Cu-based Metal-Organic Framework (MOF), namely copper-terephthalate (Cu(1,4-BDC)), was successfully synthesized by electrochemical method for effective methylene blue (MB) sorption from aqueous solutions. The composition, morphology, and the presence of functional groups in the obtained material were verified by Fourier Transform Infrared spectroscopy (FTIR), Powder X-Ray Diffraction (PXRD), Thermal (TGA), and Elemental (EA)...
-
Lead(II) coordination polymers with imidazole-4- and pyrazole-3-carboxylate isomeric linkers: Structural diversity and luminescence properties
PublicationUsing 1H-imidazole-4-carboxylic acid (4imCOOH) and 1H-pyrazole-3-carboxylic acid (3pyrCOOH) coordination polymers [Pb(4imCOO)2(H2O)]n (1) and [Pb2(3pyrCOO)4]n (2) were constructed. Obtained polymers were characterized via FT-IR, X-ray, PL and TG methods. The coordination polyhedron around Pb(II) in 1 is described as distorted pentagonal pyramid with hemidirected coordination sphere (based on DFT calculations). Compound 2 consists...
-
Statyczne i dynamiczne badania własności masy polimerowej
PublicationPolimer jest materiałem, który coraz częściej znajduje zastosowanie w budownictwie w przypadku konstrukcji narażonych na wpływy dynamiczne. Poprzez dodanie do składu polimeru odpowiednich składników możliwe jest otrzymanie materiału o specjalnych parametrach, np. o zwiększonym tłumieniu. Od kilku lat masa polimerowa stosowana jest w tzw. metodzie złączy podatnych. Potwierdzono również jej efektywność w zastosowaniu do elementów...
-
Application of g-C3N4/ZnO nanocomposites for fabrication of anti-fouling polymer membranes with dye and protein rejection superiority
Publication -
The Application of Polymer Inclusion Membranes for the Removal of Emerging Contaminants and Synthetic Dyes from Aqueous Solutions—A Mini Review
Publication -
Copper recovery from model chloride solution using polymer inclusion membranes with 1-decyl-2,4-dimethylimidazle
Publication -
The Influence of the Morphology and Mechanical Properties of Polymer Inclusion Membranes (PIMs) on Zinc Ion Separation from Aqueous Solutions
Publication -
MO‐F‐214‐06: Linear Energy Transfer Response of Polymer Gel Dosimeters in Therapeutic Proton Beams
Publication -
SU‐GG‐T‐270: Evaluation of a Novel 3‐D Polymer Gel Dosimetry System for Proton Radiotherapy
Publication -
SU-GG-T-267: Imaging Properties of the OCTOPUSTM-IQ Scanner in Combination with a New Polymer Gel Dosimeter
Publication -
Multistep energy migration between 3,3'-diethyl-9-methylthiacarbocyanine iodide monomers in uniaxially oriented polymer films
PublicationWykonano pomiary obserwabli fluorescencyjnych dla wieloetapowego transferu energii w układzie zawierającym MDTCI (3,3'-diethyl-9-methylthiacarbocyanine iodide) w rozciąganych osiowo foliach polimerowych (PVA). Wyniki doświadczalne porównano z rezultatami symulacji Monte Carlo, stwierdzając ich bardzo dobrą zgodność. Ponadto z symulacji Monte Carlo otrzymano szereg informacji nie dających się zmierzyć doświadczalnie jak np. czas...
-
Characterization of structure and properties of polymer films made from blends of polyethylene with poly(4-methyl-1-pentene)
Publication -
Large deformations formulation and elastic instability of single layer nanoplate embedded on polymer medium in nonlocal continuum mechanic
Publication -
The Effect of Polymer Microstructure on Encapsulation Efficiency and Release Kinetics of Citropin 1.1 from the Poly(ε-caprolactone) Microparticles
Publication -
Composite Materials Based on Polymer-Derived SiCN Ceramic and Disordered Hard Carbons as Anodes for Lithium-Ion Batteries
PublicationNew composite materials based on polymer-derived SiCN ceramics and hard carbons were studied in view of its application as anodes for lithium-ion batteries. Two kinds of composites were prepared by pyrolysis of the preceramic polysilazane (HTT1800, Clariant) at 1000 °C in Ar atmosphere mixed with hard carbons derived from potato starch (HC_PS) or with a hard carbon precursor, namely potato starch (PS), denoted as HTT/HC_PS and...
-
The electrochemical impedance spectroscopy studies of the anode material based on polymer and starch derived ceramic for lithium ion batteries
PublicationThe anode materials derived of preceramic polymer poly(1,2-dimethylsilazane) (PSN) and starch was study. Commercially available polysilazane (poly(1,2-dimethylsilazane (PSN 2M01 Gelest) was mixed with commercially available starch (POCH Gliwice). The ratio polymer/starch (PSN/starch) was 1/1 or 3/7. The polysialazane/starch blend was cross-linked at 230 ºC for 2 h followed by heating to the final temperature (500 ºC, 700 ºC and...
-
Raman scattering measurements in monitoring of polymer synthesis process. Lightmetry 2002 : Metrology and Testing Techniques Using Light.
PublicationW artykule omówiono możliwości wykorzystania pomiarów ramanowskich do monitorowania w czasie rzeczywistym przebiegu procesów syntezy materiałów polimerowych. Wykorzystano sondy światłowodowe do sprzęgnięcia aparatury pomiarowej z typowym stanowiskiem technologicznym. Pomiary miały charakter zdalny, nieniszczący i niezakłócający przebieg reakcji.
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublicationTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
Recycled rubber wastes-based polymer composites with flame retardancy and electrical conductivity: Rational design, modeling and optimization
PublicationPolymer recycling techniques experience a maturity period of design and application. Rubbers comprise a high proportion of polymer wastes, highly flammable and impossible to re-melt. Polymer composites based on ground tire rubber (GTR) and ethylene-vinyl acetate copolymer (EVA) containing carbon black (CB) (1–50 phr), with variable EVA/GTR weight composition (10/90, 25/75, 50/50, 75/25 and 90/10), and processing temperature (Low:...
-
Application of g-C3N4/ZnO nanocomposites for fabrication of anti-fouling polymer membranes with dye and protein rejection superiority
PublicationPolysulfone (PSf) membranes are privileged for water and wastewater treatment, but because of their hydrophobic nature, they suffer from fouling, which lowers their performance and lifetime. In this work, g-C3N4 and g-C3N4/ZnO nanomaterials were synthesized via a hydrothermal method to modify the PSf membrane for effective dye separation and reduction of organic fouling. Since g-C3N4/ZnO possesses –OH and –NH reactive groups, g-C3N4/ZnO/PSf...
-
Load-carrying capacity and state of effort of tubes made of glass and basalt fibre reinforced polymer filled with concrete
PublicationOpisano badania eksperymentalne słupów wykonanych z rur polimerowych zbrojonych włóknami szklanymi i bazaltowymi. Część rur wypełniano wewnątrz betonem. Słupy z wypełnieniem niszczyły się w sposób powolny, wykazując wysoką nośność pokrytyczną, podczas gdy słupy z rur pustych niszczyły się w sposób gwałtowny, niesygnalizowany. Nośności uzyskane eksperymentalnie porównano do nośności obliczonych teoretycznie na podstawie procedur...
-
Modyfikacja biodegradowalnych poliestrów alifatycznych za pomocą inicjatorów nadtlenkowych
PublicationCzynniki ekologiczne, ekonomiczne oraz większa świadomość społeczeństwa wpływają korzystnie na dynamiczny rozwój bio- degradowalnych materiałów, które sukcesywnie zastępują polimery „konwencjonalne”. Biodegradowalne polimery zarówno ze źródeł odnawialnych, jak i nieodnawialnych wzbudzają duże zainteresowanie wielu jednostek naukowo-badawczych oraz firm, głównie w zakresie ich modyfikacji. W pracy przedstawiono wyniki badań wpływu...
-
Novel Cell Permeable Polymers of N-Substituted L-2,3-Diaminopropionic Acid (DAPEGs) and Cellular Consequences of Their Interactions with Nucleic Acids
Publication -
Molecularly imprinted polymers based on deep eutectic solvents as a greenest materials for selective extraction of emerging contaminants from complex samples
PublicationSome of the reagents applied in the synthesis of molecularly imprinted polymers (MIPs) may impact on health and the environment. Thus, a new generation of promising green chemicals are nowadays introduced and investigated, including deep eutectic solvents (DESs). DESs seems to be a reasonable choice as they are characterized as non-toxic, low cost, easy to prepare and biodegradable chemicals. This review presents the information...
-
Quantum and carbon dots conjugated molecularly imprinted polymers as advanced nanomaterials for selective recognition of analytes in environmental, food and biomedical applications
PublicationSamples with complex matrix analyzed during explanation of pathogenesis of various diseases and food or environmental monitoring request advanced analytical and instrumental devices. Among the materials used for described purposes, quantum (QDs) or carbon dots (CDs) layered by molecularly imprinted polymer (MIP) shells have gained widespread attention. Unique optical and physicochemical properties of QDs/CDs together with high...
-
Copper and copper-manganese 1D coordination polymers: Synthesis optimization, crystal structure and preliminary studies as catalysts for Baylis–Hillman reactions
PublicationThis work reports the influence of experimental parameters (pH and counter-ion) in the synthesis of the 1D coordination polymer [Cu(IDA)(H2O)2]n (IDA = iminodiacetate), named here Cu-IDA. Copper-manganese bimetallic coordination polymers were also obtained by isomorphic replacement into Cu-IDA structure, with different molar ratio of Cu2+ and Mn2+ ions, denoted here as Cu/Mn-IDA (0.9/0.1; 0.7/0.3 and 0.5/0.5). New coordination...
-
Copper(I) halide cluster-based coordination polymers modulated by chiral ditopic dithiodianthranilide ligands: synthesis, crystal structure and photoluminescence
PublicationReaction of copper(I) halides with chiral dithiodianthranilidesmdtaandbdtaafforded polymeric complexeswhere polynuclear CuX clusters were linked together by ditopic bridging ligands into 1D chains or 2D layerstructures. In the case of racemic ligands double stranded chain polymers were formed where the Cu4X4(X = I or Br) cores are connected by enantiomeric pairs of the ditopic ligands. In contrast, a homochiralmdtaligand created...
-
New coordination polymers based on a V-shaped ligand and lanthanides: Structural description and symmetry-luminescence correlation using europium as a probe
PublicationWe have synthesized new luminescent coordination polymers using 4,4'-sulfonyldibenzoic acid (H2SDA) and several lanthanide ions by open crystallization in DMF. Three different 1-D structures were obtained, as determined by single-crystal X-ray diffraction: [La(η2-NO3)(μ-SDA)(DMF)3]n (1), [Sm(η2-NO3)(μ-SDA)(DMF)2 2DMF]n (3), [Ln(η2-NO3)(μ-SDA)(DMF)2 DMF]n (Ln ¼ Eu (4), Dy (5), Ho (6), Er (7), Tm (8) and Lu(9)). A 2-D structure,...
-
Preliminary Testing of the Influence of Modified Polycaprolactones on Anabaena Variabilis Growth in Seawater
PublicationSeveral new biodegradable polymer materials have recently come onto the global market. Mostly the results on degradation kinetic studies are presented. This paper suggests using one of the tests to estimate the impact of polymer packaging material on sea life. The microorganism chosen was Anabaena variabilis (identified in many waters, including those of the Baltic Sea, especially in the Gulf of Gdansk and Puck Bay; this cyanobacterium...
-
Temperature Coefficient of Electronic Polarizability in Thin Polymer Films Deposited on Si and SiO2 Substrates Determined via Spectroscopic Ellipsometry
PublicationEllipsometry is widely used to determine the thermo-optical properties of thin polymer films. However, if the thermo-optic coefficient (TOC) and the linear thermal expansion coefficient (LTEC) are to be used to determine the temperature coefficient of electronic polarizability (TCEP) in thin polymer films, their values must be determined with the greatest possible accuracy, as both have the opposite effect. In this article,...
-
SU-FF-T-284: Linear Energy Transfer (LET) Dependence of BANG® Polymer Gel Dosimeters in Proton Beams
Publication -
Three-dimensional visualization and measurement of conformal dose distributions using magnetic resonance imaging of bang polymer gel dosimeters
Publication -
Phosphorus, nitrogen and oxygen co-doped polymer-based core-shell carbon sphere for high-performance hybrid supercapacitors
Publication -
All solid state electrodes taste sensor with modified polymer membranes for discrimination of mineral water with different CO2 content
PublicationA potentiometric taste sensor with All Solid State Electrodes containing five all solid state electrodes with appropriate lipophilic compounds (benzyldimethyltetradecylammonium chloride, dodecyltrimethylammonium bromide, palmitic acid, stearic acid, and phytol) embedded in a polymer membrane was applied for discrimination of mineral water samples differed in CO2 content. Samples of still, slightly sparkling, and sparkling Naleczowianka...
-
Structure and electrical properties of Y, Fe-based perovskite mixed conducting composites fabricated by a modified polymer precursor method
PublicationIn this work, samples of Y0.07Sr0.93Ti1-xFexO3-d with 20, 40, 60 and 80 mol% of iron amount were prepared by a low-temperature polymer precursor method. The SEM-EDS analysis proved that analyzed Y0.07Sr0.93Ti1-xFexO3-d samples were composites of two Ti- and Fe-rich perovskite samples. This kind of composite consists of two phases in which one has a good ionic and the other electronic conductivity, which makes such a composite a...
-
Polymer journal bearings behaviour research under limited lubrication and cooling conditions conducted on high torque test rig
PublicationPolymer journal bearings are frequently used as a water-lubricated bearings of small marine units’ propeller shafts . Choice of these bearings is based on their simple construction and relatively low purchase and maintenance costs. Although properly designed and installed water lubricated bearings may well last for over a decade, rapid wear or failure of these bearings can be observed...
-
Pilot study of the influence of thermoplastic starch based polymer packaging material on the growth of diatom population in sea water environment
PublicationNovel polymeric packaging materials susceptible to environmentally friendly decomposition appeared on the global market. The paper is devoted to an investigation of the impact of degradable polymer packaging on marine life. The chosen polymer was a commercial packaging based on thermoplastic starch (TPS over 85%). The microorganism chosen was Phaeodactylum tricornutum diatom (identified in many aquatic reservoirs, with a tendency...
-
Core-Shell Nanoparticles with Hyperbranched Poly(arylene-oxindole) Interiors
PublicationCore-shell type star polymers composed of poly(tert-butyl acrylate) (poly(t-BuA)) arms and 100% hyperbranched poly(arylene-oxindole) interiors were synthesized via the "core-first" method. Atom transfer radical polymerization of t-BuA initiated by 2-bromopropionyl terminal groups of the hyperbranched core was applied for the synthesis of the stars. The resultant star structures were characterized by gel permeation chromatography...