Search
Filters
total: 427
filtered: 318
-
Catalog
Chosen catalog filters
Search results for: LFM
-
Broadband LFM signal source for a module-based diver detection sonar
PublicationPraca przedstawia koncepcję źródła impulsów sondujących sonaru DDS, dla pogrupowanych po stronie nadawczej elementarnych sekcji przetwornika w moduły 8 lub 16 elementowe. Na podstawie oszacowania teoretycznego i pomiarów czwórnikowych określono potrzebną moc wyjściową i topologię tych nadajników. Przedstawione są też uzyskane na drodze pomiarów charakterystyki częstotliwościowe modułów przetwornika, razem z zastosowanym układem...
-
The study of harmonic imaging by AFM = Badania harmonicznych w obrazowaniu AFM
Publication -
A novel method of local chirp-rate estimation of LFM chirp signals in the time-frequency domain
PublicationIn the paper, novel dynamic representations of a complex signal in the time-frequency domain are introduced. The proposed approach is based on using the gradient of the short-time Fourier transform complex phase. A channelized instantaneous complex frequency (CICF) and a complex local group delay (CLGD) are included in the presented signal representations. An application of the newly-introduced distributions is demonstrated by...
-
Simulation and measurements for the substance identification by AFM
Publication -
Morphology of polyurethanes revisited by complementary AFM and TEM
PublicationPrzedmiotem badań mikroskopowych TEM i AFM były lane segmentowe poliuretany o zawartości 30 i 50% segmentu sztywnego. Stwierdzono obecność sferolitów (poziom mikrometrów), fibryl i globul. Ponadto zastosowanie AFM pozwoliło na zbadanie nanomorfologii badanych poliuretanów. Zaobserwowano krótkie, cylindropodobne domeny segmentów sztywnych rozproszone w matrycy segmentów giętkich.
-
AFM-assisted investigation of conformal coatings in electronics
PublicationPurpose – This paper aims to presents a new method of investigation of local properties of conformal coatings utilized in microelectronics. Design/methodology/approach – It is based on atomic force microscopy (AFM) technique supplemented with the ability of local electrical measurements, which apart from topography acquisition allows recording of local impedance spectra, impedance imaging and dc current mapping. Potentialities...
-
Improving AFM images with harmonic interference by spectral analysis
PublicationPrzedstawiono sposób usunięcia zakłóceń pojawiających się na obrazach uzyskiwanych z mikroskopu sił atomowych (AFM). Przybliżono kilka metod stosowanych do redukcji zakłóceń w obrazach. Następnie opisano zidentyfikowane zakłócenia harmoniczne oraz zaproponowany sposób ich znaczącej redukcji. W pracy zamieszczono szereg obrazów uzyskanych z mikroskopu AFM ilustrujących efekty powodowane zakłóceniami oraz skuteczność zaproponowanej...
-
Corrosion process monitoring by AFM higher harmonic imaging
PublicationThe atomic force microscope (AFM) was invented in 1986 as an alternative to the scanning tunnelling microscope, which cannot be used in studies of non-conductive materials. Today the AFM is a powerful, versatile and fundamental tool for visualizing and studying the morphology of material surfaces. Moreover, additional information for some materials can be recovered by analysing the AFM's higher cantilever modes when the cantilever...
-
RFM-based repurchase behavior for customer classification and segmentation
Publication -
Evaluation of organic coatings condition with AFM-based method
PublicationThe paper presents an atomic force microscopy (AFM)-based approach to evaluation of local protective properties of organic coatings. Apart from topography, it provides local ac and dc characteristics of examined coating. The method consists in application of ac voltage perturbation signal between conductive AFM tip and coated metal substrate. The resulting current is used to determine local impedance characteristics. Both impedance...
-
Beyond Traditional Learning: The LLM Revolution in BPM Education at University
PublicationLarge Language Models (LLMs) significantly impact higher education, requiring changes in educational processes, especially in Business Process Management (BPM) practical exercises. The research aims to evaluate the effectiveness of LLMs in BPM education to determine if LLMs can supplement educators. The study involved 33 master’s degree students. Students’ works were manually evaluated and compared to LLM-generated responses. Results...
-
AFM, XRD and HRTEM studies of annealed FePd thin films
Publication -
Exploring the nanoscale: AFM-IR visualization of cysteine adsorption on gold nanoparticles
Publication -
Estimation of the uncertainty of the LEM CV 3-500 transducers processing function
PublicationThe paper presents the methodology for estimating uncertainty of a voltage transducer processing function based on the example of LEM CV 3-500 transducer. The analysis was performed using the method based on the GUM Guide propagation of uncertainty law and the Monte Carlo numerical method. The article also presents a comparative analysis of the results of a voltage measurement evaluation done using the Monte Carlo simulation method,...
-
TEM and AFM studies of segmented polyester polyurethanes obtained by quasi-prepolymer method.
PublicationPrzedmiotem badań były poliestrouretany o zawartości 50% segmentów sztywnych i zmiennym stosunku NCO/OH. Wykazano, że poliestrouretany otrzymane metodą quasi-prepolimerową wykazują inną morfologię niż otrzymane za pomocą metody prepolimerowej. W poliuretanach quasi- prepolimerowych obserwowano za pomocą mikroskopu AFM agregację segmentów sztywnych o wymiarze poprzecznym rzędu200nm. Segmenty te tworzyły fazę ciągłą. Kruche...
-
Hyperelastic Microcantilever AFM: Efficient Detection Mechanism Based on Principal Parametric Resonance
PublicationThe impetus of writing this paper is to propose an efficient detection mechanism to scan the surface profile of a micro-sample using cantilever-based atomic force microscopy (AFM), operating in non-contact mode. In order to implement this scheme, the principal parametric resonance characteristics of the resonator are employed, benefiting from the bifurcation-based sensing mechanism. It is assumed that the microcantilever is made...
-
Localized impedance measurements of AA2024 and AA2024-T3 performed by means of AFM in contact mode
PublicationPurpose: The purpose of this paper is to present the results of an atomic force microscopy (AFM) based approach to local impedance spectroscopy (LIS) measurement performed on AA2024 and AA2024-T3 aluminium alloys. Design/methodology/approach: AFM-LIS measurements were performed ex-situ without the electrolyte environment, so in fact the electrical not electrochemical impedance was obtained. Findings: Relative local impedance values...
-
Localized impedance measurements of AA2024 and AA2024‐T3 performed by means of AFM in contact mode
Publication -
Szacowanie niepewności funkcji przetwarzania przetwornika LEM CT -5T metodą Monte Carlo
PublicationW referacie zaprezentowano metodologię szacowania niepewności funkcji przetwarzania przetwornika prądowego, na przykładzie przetwornika LEM CT-5T, przy zastosowaniu metody opartej na Przewodniku GUM z zastosowaniem prawa propagacji niepewności oraz metody numerycznej Monte Carlo. Przedstawiono szczegółową analizę doboru rozkładu wielkości wejściowej. W przypadku metody Monte Carlo dobór rozkładu wielkości wejściowych jest bardzo...
-
Szacowanie niepewności funkcji przetwarzania przetwornika LEM CT -5T metodą Monte Carlo
PublicationW referacie zaprezentowano metodologię szacowania niepewności funkcji przetwarzania przetwornika prądowego, na przykładzie przetwornika LEM CT-5T, przy zastosowaniu metody opartej na Przewodniku GUM, z zastosowaniem prawa propagacji niepewności oraz metody numerycznej Monte Carlo. Przedstawiono szczegółową analizę doboru rozkładu wielkości wejściowej. W przypadku metody Monte Carlo dobór rozkładu wielkości wejściowych jest bardzo...
-
Modelowanie osiągów niskoemisyjnych ogniw paliwowych za pomocą modeli matematycznych typu CFM.
PublicationW artykule przedstawiono matematyczny model rurkowego ogniwa paliwowego i jego implementację do własnego kodu typu CFM (Computational Flow Mechanics) o nazwie COM-GAS. Kody numeryczne CFM pozwalają przewidzieć podstawowe parametry ogniwa takie jak: prąd, napięcie, skład spalin etc. Napięcie generowane przez ogniwo paliwowe wyznaczono na podstawie rozszerzonego równania Nernsta. Skład spalin oszacowano opierając się o stałą równowagi...
-
Performance of zinc-rich coatings evaluated using AFM-based electrical properties imaging
PublicationThe paper presents the results of investigation of polyvinyl zinc-rich coating exposed to 97% relativehumidity atmosphere for 40 days. Condition of the coating and evolution of its protective properties weredetermined with the novel AFM-based approach capable of providing surface profiles, local dc currentmaps as well as local impedance spectra. The proposed technique allowed insight into the local changesof coating topography...
-
Doppler effect in the CW FM sonar
PublicationWhen sonars are used for military purposes they have to ensure unobtrusive operation, a feature that can be potentially secured by 'silent sonar' or continuous wave frequency modulation sonars (CW FM sonars). The article presents how these sonars operate and identifies the relations between their parameters. The Doppler effect and its impact on the CW FM sonar are studied to identify how it affects the sonar's parameters. The results...
-
Temporal sequence of the human RBCs' vesiculation observed in nano-scale with application of AFM and complementary techniques
Publication -
Assessment of copper surface coverage with corrosion inhibitor using AFM-based local electrical measurements
PublicationThe paper presents a new method of assessment of metal surface coverage with corrosion inhibitor and thus of inhibitor protective performance. It is based on the atomic force microscopy measurement performed in a contact mode. Apart from topography images the proposed approach allows acquisition of local DC maps and local electrical impedance spectra via application of DC bias voltage or AC perturbation signal between the conductive...
-
Demodulacja AM-FM dyskretnych sygnałów świergotowych
PublicationW pracy zaprezentowano dwa nowe krótkie (4-punktowe) estymatory amplitudy chwilowej rzeczywistych sygnałów świergotowych (ang. chirp) współpracujące z 4-punktowym estymatorem pulsacji chwilowej MODCOV4p. W ten sposób otrzymano dwa demodulatory AM-FM o stosunkowo dużej dokładności obu estymat i o zakresie dynamicznym AM i FM wystarczająco szerokim do większości praktycznych zastosowań.
-
Mutual Clutter Suppression Techniques for FM Sonars
PublicationThe article presents methods that help in the elimination of mutual clutter as well as the consequences of two FM sounding signal sonars operating in the same body of water and frequency band. An in-depth analysis of mutual clutter was carried out. The effects of sounding signal differentiation were determined, as was the Doppler effect on mutual clutter suppression. One of the methods analysed is of particular interest in a situation...
-
THE ECONOMIC EFFICIENCY OF GROWING SWEET POTATO (IPOMOEA BATATAS L. [LAM.]) IN POLISH SOIL AND CLIMATE CONDITIONS
Publication -
Investigation of morphological and electrical properties of the PMMA coating upon exposure to UV irradiation based on AFM studies
PublicationCelem badania było określenie wpływu promieniowania ultrafioletowego na morfologię powierzchni powłoki i na jej właściwości elektryczne. Cienka powłoka z polimetakrylanu metylu została nałożona na podłoże stalowe metodą zanurzeniową. Oceny stanu przed ekspozycją UV i w jej trakcie dokonywano przy użyciu mikroskopu sił atomowych. Na obrazach AFM zaobserwowano pojawienie się mikropęknięć. Celem zweryfikowania czy wykryte nieciągłości...
-
Effect of Differentiated Nitrogen Fertilization on the Enzymatic Activity of the Soil for Sweet Potato (Ipomoea batatas L. [Lam.]) Cultivation
Publication -
The Effects of Temperature on the Quality and Storage Stalibity of Sweet Potato (Ipomoea batatas L. [Lam]) Grown in Central Europe
Publication -
Evaluation of adhesive forces and the specific surface energy of zirconia stabilized by yttria with alumina additions ceramic by AFM method
PublicationThe adhesive forces and the specific surface energy of ceramic material surfaces are very important for further tribological and biomedical applications of ceramics. Partially stabilized zirconia (zirconium oxide) is popular for manufacturing various medical products. ZrO2 stabilized by Y2O3 with additions of 5 wt% alumina was produced by slip casting method with a subsequent sintering. Structure and chemical composition of ceramic...
-
The New LM-PCR/Shifter Method for the Genotyping of Microorganism
PublicationTechniques relies on the ligation of appropriates adapters (LM-PCR) as AFLP, PCR MP and ADSRRS are successfully used for epidemiological studies for prokaryotic and eukaryotic microorganisms. In this study we propose a new method, called the LM-PCR/Shifter, based on the use of a Class IIS restriction enzyme giving restriction fragments with different 4 base 5' overhangs (Shifter) and the ligation of appropriate oligonucleotide...
-
The Effect of Water-Soluble Polysaccharide from Jackfruit (Artocarpus heterophyllus Lam.) on Human Colon Carcinoma Cells Cultured In Vitro
Publication -
DEVONIAN SILICICLASTIC ROCKS OF THE BABÍ LOM LOCALITY (SOUTHERN MORAVIA, CZECH REPUBLIC): SEDIMENTARY ENVIRONMENT RECONSTRUCTION AND PROVENANCE STUDY
Publication -
Antioxidant properties of infusions from leaves of sweet potato (Ipomoea batatas L. Lam) depending on temperature and brewing time
Publication -
Morphological and molecular genetic diversity analysis using SSR markers in Jackfruit (Artocarpus heterophyllus Lam.) genotypes for pulp colour
Publication -
Electrical mapping of AISI 304 stainless steel subjected to intergranular corrosion performed by means of AFM-LIS in the contact mode
PublicationThe paper presents results of the AFM-based approach to local impedance spectroscopy (LIS) measurements performed in a 20 20 lm grid within an austenite grain–grain boundary region for sensitized AISI 304 stainless steel (SS). Maps of electrical parameters obtained on the basis of localized impedance spectra were demonstrated, presenting their changes and correlation with the sample topography. Performed research revealed significant...
-
Integration of Fluorescent, NV-Rich Nanodiamond Particles with AFM Cantilevers by Focused Ion Beam for Hybrid Optical and Micromechanical Devices
PublicationIn this paper, a novel fabrication technology of atomic force microscopy (AFM) probes integrating cantilever tips with an NV-rich diamond particle is presented. Nanomanipulation techniques combined with the focused electron beam-induced deposition (FEBID) procedure were applied to position the NV-rich diamond particle on an AFM cantilever tip. Ultrasonic treatment of nanodiamond suspension was applied to reduce the size of diamond...
-
Chirp-rate estimation of FM signals in the time-frequency domain
PublicationNovel dynamic representations of a complex signal in the time-frequency domain including: a channelized instantaneous complex frequency (CICF), a complex local group delay (CLGD) and a channelized instantaneous chirp-rate (CICR) are introduced. The proposed approach is based on the use of the gradient of the short-time Fourier transform complex phase. An interpretation of the newly-introduced distributions especially of the CICR...
-
Distance measurement errors in silent FM-CW sonar with matched filtering
PublicationThe secretiveness of sonar operation can be achieved by using continuous frequency-modulated sounding signalswith reduced power and significantly prolonged repeat time. The application of matched filtration in the sonarreceiver provides optimal conditions for detection against the background of white noise and reverberation, and avery good resolution of distance measurements of motionless targets. The article shows that target...
-
Electronic conductivity in the SiO2-PbO-Fe2O3 glass containing magnetic nanostructures
PublicationThe linear impedance spectra of iron–silicate–lead glass samples were measured in the frequency range from 1 MHz to 1 MHz and in the temperature range from 153 K to 423 K. The structure was investigated by means of XRD and atomic force microscopy. Local electrical and magnetic properties of the samples were tested with the aid of electrostatic force microscopy (EFM) and magnetic force microscopy (MFM). The obtained results show...
-
The effects of variable nitrogen fertilization on amino acid content in sweet potato tubers (Ipomoea batatas L. [Lam.]) cultivated in central and eastern Europe
Publication -
Analysis of distance measurement errors in CW FM sonar with MLS code modulation
PublicationAlthough used in the classic silent sonar, the CW FM sounding signal has a major flaw which is its inaccuracy in determining the distance to a target. The authors of the article have developed a concept of silent sonar using frequency modulation signals switched by pseudorandom codes, already discussed in their previous work. This article presents a detailed analysis of errors in CW FM sonar with pseudo-random sequence code modulation...
-
Reception of Terrestrial DAB+ and FM Radio with a Mobile Device: A Subjective Quality Evaluation
PublicationNowadays, terrestrial broadcasting enables to receive content anytime and everywhere. People can obtain information both with a portable or desktop receiver, which include pocket-sized devices as well as high-end Hi-Fi equipment, not to mention car audio systems. Numerous manufacturers include FM-compatible chipsets in a variety of user equipment (UE), including mobile phones. However, digital radio signal processing modules, such...
-
Impact response of two-layered grouted aggregate fibrous concretecomposite under falling mass impact
PublicationTwo-layered Grouted Aggregates Fibrous Concrete Composite (TGAFCC) is a new category concrete which became popular recently and attracted the attention of researchers globally. Recent studies indicated that TGAFCC has notable improvement in mechanical properties, which has been sufficiently documented. However, the impact behaviour of TGAFCC when combined with Glass Fibre Mesh (GFM) and Textile Fibre Mesh (TFM) is still unexplored....
-
A Multichannel Receiver of the Experimental FM Based Passive Radar Using Software Defined Radio Technology
Publication -
Digital Transformation of Terrestrial Radio: An Analysis of Simulcasted Broadcasts in FM and DAB+ for a Smart and Successful Switchover
PublicationThe process of digitizing radio is far from over. It is an important interdisciplinary aspect, involving Big Data and AI (Artificial Intelligence) when it comes to classifying and handling content, and an organizational challenge in the Industry 4.0 concept. There exist several methods for delivering audio signals, including terrestrial broadcasting and internet streaming. Among them, the DAB+ (Digital Audio Broadcasting plus)...
-
Surface characteristics of glass fibres covered with an aluminum layer after a chemical modification process using secondary ion mass spectrometry (SIMS) and atomic force microscopy (AFM)
PublicationPrzedstawiono wyniki z badań powierzchni modyfikowanych włókien szklanych (przed i po procesie chemicznej modyfikacji ich powierzchni), które są kandydatem na przyszły oryginalny bezmatrycowy materiał odniesienia lotnych analitów etenu (C2H4) metodami spektrometrii mas jonów wtórnych oraz mikroskopii sił atomowych. Badania miały na celu obserwację zmian oraz procesów, jakie zaszły na powierzchni włókien szklanych pokrytych...
-
LF NMR spectroscopy analysis of water dynamics and texture of Gluten-Free bread with cricket powder during storage
Publication