Search
Filters
total: 1339
-
Catalog
displaying 1000 best results Help
Search results for: BIOGAS MANUFACTURE
-
Salud y Drogas
Journals -
Lignocellulosic waste biosorbents infused with deep eutectic solvents for biogas desulfurization
PublicationThis paper introduces an innovative method for treating biogas streams, employing lignocellulosic biosorbents infused with environmentally friendly solvents known as deep eutectic solvents (DES). The primary focus of this study was the elimination of volatile organosulfur compounds (VSCs) from model biogas. Biosorbents, including energetic poplar wood, antipka tree, corncobs, and beech wood, were used, each with varying levels...
-
Biogas upgrading using supported liquid membranes based on ionic liquids
PublicationZastosowanie cieczy jonowych osadzonych w porach nośników polimerowych bądź ceramicznych jest nowoczesnym podejściem do separacji ditlenku węgla z mieszanin gazowych. Znikoma prężność par cieczy jonowych i możliwość modyfikacji budowy kationu i wyboru anionu wchodzących w skład cieczy jonowych sprawiają, że związki te mogą zastąpić obecnie stosowane w procesach separacji aminy. W publikacji przedstawiono wpływ struktury chemicznej,...
-
The Impact of Technological Processes on Odorant Emissions at Municipal Waste Biogas Plants
Publication -
Historical, technical and economic aspects of biogas development: Case Polanda and Ukraine
PublicationThe paper describes 3700 years of biogas manufacture with more details of last 120 years. Due to V. Omelianskij׳s researches 120 years ago, Ukrainians achieved a share in biogas manufacture in the overall biogas development. Poland started to take part in biogas development 96 years ago by finishing biogas plant in Posen 1928. History and current status of biogas plants achievements are collected and analyzed. Faults and achievements...
-
Selected Problems of Cogeneration Energy Systems Designing, Fueled with Landfill Biogas
PublicationThe article discusses the impact of the quality of biogas fuel for operation of generating sets with internal combustion engines. There are presented selected investigation results of landfill biogas fueled gensets operation. The article includes also discussion of the possibility of increasing the efficiency of biogas fuelled cogeneration systems. It also presents guidelines for the optimal design of landfill biogas fueled engines,...
-
Purification of model biogas from toluene using deep eutectic solvents
PublicationBiogas from landfills and wastewater treatment facilities typically contain a wide range of volatile organic compounds (VOCs), that can cause severe operational problems when biogas is used as fuel. Among the contaminants commonly occur aromatic compounds, i.e. benzene, ethylbenzene, toluene and xylenes (BTEX). In order to remove BTEX from biogas, different processes can be used. A promising process for VOCs removal is their absorption...
-
Cyclic deformation and fracture behaviour of additive manufactured maraging steel under variable-amplitude loading
PublicationThe cyclic deformation and fracture behaviour of 18Ni300 maraging steel produced by laser beam powder bed fusion is studied under variable-amplitude loading. The tests were conducted under fully-reversed strain-controlled conditions with a loading sequence comprising three ascending cycles and three descending cycles repeated sequentially until failure. After the tests, fracture surfaces were examined using height and volume surface...
-
GROUPS OF GERMAN DOMESTIC APPLIANCE MANUFACTURERS ACCORDING TO NEW PRODUCT DEVELOPMENT PRACTICES
PublicationFinding the best way to develop new products has been always a hot topic for practitioners and academics. However, so far only a few of these kinds of studies have concentrated on a single industry. In this paper, we group German domestic appliance manufacturers with regards to their new product development (NPD) practices to discover their attitude to NPD effort. By conducting a survey we found that three different groups of manufacturers...
-
Low-Cost Method for Internal Surface Roughness Reduction of Additively Manufactured All-Metal Waveguide Components
PublicationIn this study, a novel low-cost polishing method for internal surface roughness reduction of additively manufactured components, developed for waveguide (WG) circuits operating in the millimeter frequency range is proposed. WG components fabricated using powder bed fusion (PBF) generally feature roughness of ten to fifty microns, which influences the increase of roughness-related conductor power losses having a major effect on...
-
Orientation effects on the fracture behaviour of additively manufactured stainless steel 316L subjected to high cyclic fatigue
PublicationIn this paper, stainless steel 316L (SS316L) bars were additively manufactured (AM) in three orientations (Z – vertical, XY – horizontal, ZX45 – midway between vertical and horizontal) by using the Laser Powder Bed Fusion Melting (LPBF-M) method. The AM specimens were subjected to load control fatigue testing under full tension and compression (R = -1) at stress amplitudes ±350, ±400 and ±450 MPa. The XY and ZX45 printing orientations...
-
Effect of printing direction on fatigue response and damage development in additive manufactured Haynes 282 nickel superalloy
Publication -
Proteolysis in dry-aged loins manufactured with sonicated pork and inoculated withLactobacillus caseiŁOCK 0900 probiotic strain
Publication -
Improvement of microstructure and mechanical properties of high dense sic ceramics manufactured by high-speed hot pressing
PublicationNon-oxide ceramics possess high physical-mechanical properties, corrosion and radiation resistance, which can be used as a protective materials for radioactive wastes disposal. The aim of the present study was the manufacturing of high density SiC ceramics with advanced physical and mechanical parameters. The high performance on the properties of produced ceramics was determined by the dense and monolithic structure. The densified...
-
Comparison of AHP and Numerical Taxonomy Methods Based on Biogas Plant Location Analysis
PublicationThe paper presents a comparison of the multi-criteria Analytic Hierarchy Process (AHP) method and numerical taxonomy in biogas plant location selection. Biogas plants are sources that will significantly contribute to the implementation of the provisions of the energy and climate package for Poland by 2030. Increasing the share of energy produced from renewable sources, e.g. biogas plants, will increase the country’s energy security....
-
The Use of Chemical Sensors to Monitor Odour Emissions at Municipal Waste Biogas Plants
Publication -
Methods of Assessing Odour Emissions from Biogas Plants Processing Municipal Waste
Publication -
CeCu2O4 as a functional layer on solid oxide fuel cells for synthetic biogas reforming
PublicationSolid Oxide Fuel Cells (SOFC) are one of the most promising electrochemical devices, which can convert chemical energy to the electrical energy these days. Their ability to work with different kind of fuel makes them noteworthy. SOFC can work with biogas. The problem arises when solid carbon starts to be deposited in anode. That leads to degradation of fuel cell. Simple solution is to apply catalytic functional layer, which is...
-
Possibilities of Leachate Co-Treatment Originating from Biogas Production in the Deammonification Process
PublicationIn the methane fermentation process, sewage sludge is the single substrate or serves as a co-substrate with the addition of various waste products. After the treatment stable digestate is obtained, which consists of two phases solid and liquid. Liquid phase, called as a leachate, due to the high content of nutrients must be treated before they are discharged into the final receiver. Physical and chemical methods of leachate treatment...
-
New Carvone-Based Deep Eutectic Solvents for Siloxanes Capture from Biogas
PublicationDuring biogas combustion, siloxanes form deposits of SiO2 on engine components, thus shortening the lifespan of the installation. Therefore, the development of new methods for the purification of biogas is receiving increasing attention. One of the most effective methods is physical absorption with the use of appropriate solvents. According to the principles of green engineering, solvents should be biodegradable, non-toxic, and...
-
Deodorization of model biogas by means of novel non-ionic deep eutectic solvent
PublicationThe paper presents new non-ionic deep eutectic solvent (DES) composed of natural and non-toxic components i.e. guaiacol, camphor and levulinic acid in 1:1:3 molar ratio as a promising absorbent for removal of selected volatile organic compounds (VOCs) including dichloromethane, toluene, hexamethyldisiloxane and propionaldehyde from model biogas. The affi nity of DES for VOCs was determined as vapour-liquid coeffi cients and the...
-
Phosphorus and nitrogen forms in liquid fraction of digestates from agricultural biogas plants
PublicationThe novelty of the presented research is the determination of the nitrogen and phosphorus fraction in the liquid fraction of digestate from agricultural biogas plants. This information is important because it can help in proposing possible further liquid fraction management or developing of new technologies for their purification. The research covered digestates from agricultural biogas plants, obtained from the fermentation of...
-
Suitability of biomass from waste wood composites for liquid biofuel production Możliwość wykorzystania biomasy poużytkowych tworzyw drzewnych w technologii ciekłych biopaliw
Publication -
A procedure for the identification of effective mechanical parameters of additively manufactured elements using integrated ultrasonic bulk and guided waves
PublicationThe subject of the current work was a simple but robust novel two-stage procedure for the non-destructive determination of effective elastic constants using ultrasonic wave propagation. First, ultrasonic bulk wave velocities measured on cubic samples were used to calculate most of the elements of the stiffness matrix. Secondly, the remaining elements were determined using the dispersion curves of elastic guided waves measured on...
-
Study of the influence of high-energy milling time on the Cu–13Al–4Ni alloy manufactured by powder metallurgy process
Publication -
Removal of Siloxanes from Model Biogas by Means of Deep Eutectic Solvents in Absorption Process
PublicationThe paper presents the screening of 20 deep eutectic solvents (DESs) composed of tetrapropylammonium bromide (TPABr) and glycols in various molar ratios, and 6 conventional solvents as absorbents for removal of siloxanes from model biogas stream. The screening was achieved using the conductor-like screening model for real solvents (COSMO-RS) based on the comparison of siloxane solubility in DESs. For the DES which was characterized...
-
Structural and catalytic properties of ceria layers doped with transition metals for SOFCs fueled by biogas
PublicationThe aim of this paper was to investigate an influence of the nanocrystalline Ce0.8A0.2O2-δ (A = Mn, Fe, Co, Ni, Cu) materials on the direct internal reforming of biogas in SOFC. Structural analysis of fabricated compounds has been done. An in-situ analysis of a composition of outlet gases from operating SOFC was performed using FTIR spectroscopy with simultaneous electrical tests. It was found out, that type of dopant strongly...
-
Copper and cobalt co-doped ceria as an anode catalyst for DIR-SOFCs fueled by biogas
PublicationThe nanocrystalline compounds of Co and Cu co-doped ceria (with up to 20 mol.% of dopants) were fabricated by the reverse microemulsion synthesis method. They were deposited in a form of layers on the surface of SOFC anode in an aim to act as electrochemically active materials for biogas reforming process. Fourier Transformed Infrared Spectroscopy was used to analyze a composition of outlet gases simultaneously with the tests of...
-
Monitoring of absorptive model biogas purification process using sensor matrices and gas chromatography
PublicationThis study examined the process of purifying model biogas using a new type of absorbent based on a Deep Eutectic Solvent (DES) and a commercially available absorbent (Genosorb) to remove acetone, toluene, and cyclohexane. The main aim of the research was to control the purification efficiency using gas chromatography (GC) and an alternative method based on sensor matrices (SM). As a result of comparing the multidimensional SM signals...
-
Application of FMEA analysis for assessing reliability and risk in biogas-fueled engines operation process
PublicationW pracy zamieszczono propozycję wykorzystania analizy FMEA (ang. Failure mode and effects analysis) - analizy rodzajów i skutków możliwych błędów występujących w instalacjach przemysłowych z silnikami spalinowymi. Obserwowany w ostatnich latach rozwój energetyki rozproszonej, opartej na tłokowych silnikach spalinowych jest wynikiem m.in. prowadzonej polityki rozwoju wykorzystania odnawialnych źródeł energii (OŹE) związanej z zagospodarowaniem...
-
Identification analysis of dynamic changes in the composition of biogas and their impact on the operation of internal combustion engines
PublicationW pracy zamieszczono wyniki badań składu biogazu pozyskiwanego na komunalnym wysypisku śmieci. Pozyskiwany biogaz jest wykorzystywany do zasilania biogazowych zespołów prądotwórczych wyposażonych w silniki o zapłonie iskrowym dostosowanych do zasilania tym paliwem. Pozyskiwany biogaz powstaje w sposób naturalny w procesie beztlenowej fermentacji zachodzącej przez ok. 20 lat, w organicznej części pryzmy odpadów składowanych na wysypisku...
-
Investigation of functional layers of solid oxide fuel cell anodes for synthetic biogas reforming
PublicationSolid oxide fuel cells (SOFCs) are one of the most promising energy conversion devices due to their high efficiency, low pollution and fuel flexibility. Unfortunately, when hydrocarbons are used as a fuel, for example in the form of a biogas, solid carbon can deposit on the anode surface. This process leads to the degradation of the fuel cell performance. A possible solution to this problem is to apply an additional catalytic material,...
-
Investigation of catalytic layers on anode for solid oxide fuel cells operating with synthetic biogas
PublicationIn this paper solid oxide fuel cells operating with dry synthetic biogas have been examined. In order to increase their stability the layers of CuO-CeO2, Cu1.3Mn1.7O4 and Y0.08Sr0.92Ti0.8Fe0.2O3 -δ have been deposited on the Ni-YSZ anode site. These layers should catalyze the internal biogas reforming and prevent the carbon deposition on the anode site. It has been found that CuO-CeO2 and Cu1.3Mn1.7O4 catalysts led to an increase...
-
Sustainable energy system combined biogas-feedSolid Oxide Fuel Cell and Microalgae technology
PublicationIn the new frontier of energy and environmental safety, new efficient and clean safe energy conversion systems are required. In this sense, the present work is framed within the context of Circular Economy and proposes a multidisciplinary study for the development of more efficient, economically viable and non-polluting energy conversion systems, based on the synergetic combination of different technologies: fuel cells, biofuels,...
-
Production of Biogas from Distillation Residue as a Waste Material from the Distillery Industry in Poland
PublicationIn this paper, the possibility to obtain an alternative source of energy from methane fermentation, catalysed by biomass, has been discussed in detail. As a main substrate, the distillation residue from the distillery industry was taken in the case of mono-fermentation and its co-fermentation with sewage sludge. The results showed that higher biogas and methane production can be obtained in a mono-fermentation process. Fermentation...
-
Green monoterpenes based deep eutectic solvents for effective BTEX absorption from biogas
PublicationThe combustion of biogas which contains significant amounts of monoaromatic hydrocarbons, i.e. benzene, ethylbenzene, toluene, and xylene (BTEX) can cause many technological, environmental, and health problems. Therefore, in these studies, a new physical absorption method based on deep eutectic solvents (DES) consisting of monoterpenes and carboxylic acids was developed for BTEX removal. A total of 39 DES were synthesized, of which...
-
Analiza projektowa hybrydowej siłowni kogeneracyjnej wykorzystującej biogaz
PublicationW niniejszej pracy zawarto podstawowe wiadomości związane z biogazem, jego źródłami pozyskiwania i możliwościami wykorzystywania. Przeprowadzono analizę projektową układu hybrydowego pod kątem korzyści energetycznych wynikających z wykorzystania tego rodzaju instalacji do utylizacji biogazu rolniczego pozyskiwanego z przykładowego gospodarstwa rolniczego oraz wstępnie zaprojektowano układ przepływowy mikroturbiny gazowej. Celem...
-
Nowoczesne metody termochemicznej konwersji biomasy w paliwa gazowe, ciekłe i stałe = Modern methods of thermochemical biomass conversion into gas, liquid and solid fuels
PublicationBiomass utilization through direct- or co-combustion with coal, based on coal, hydrogen and oxygen compounds chemical energy conversion into heat in boilers, is simultaneously the cheapest and - according to experts - economically least effective solution. In case of heat and electricity production in cogeneration process in biomass fueled heat and power stations (wood, straw, energetic plants, RDF etc), investment costs are little...
-
Michał Ryms dr hab. inż.
PeopleMichał Ryms, PhD, DSc, Eng. is the physicist, graduate of the Gdańsk University of Technology. PhD thesis defended at the Chemical Faculty. Since 2011 an employee at the Department of Energy Conversion and Storage, Chemical Faculty, Gdansk University of Technology, POLAND – now as an associate professor. His research interests includes: improvement of energy efficiency and possibilities of new application of phase change materials...
-
Strain energy density and entire fracture surface parameters relationship for LCF life prediction of additively manufactured 18Ni300 steel
PublicationIn this study, the connection between total strain energy density and fracture surface topography is investigated in additively manufactured maraging steel exposed to low-cycle fatigue loading. The specimens were fabricated using laser beam powder bed fusion (LB-PBF) and examined under fully-reversed strain-controlled setup at strain amplitudes scale from 0.3% to 1.0%. The post-mortem fracture surfaces were explored using a non-contact...
-
The abrasive wear resistance of coatings manufactured on high-strength low-alloy (HSLA) offshore steel in wet welding conditions
PublicationSome marine and offshore structure elements exploited in the water cannot be brought to the surface of the water as this will generate high costs, and for this reason, they require in-situ repairs. One of the repair techniques used in underwater pad welding conditions is a wet welding method. This paper presents an investigation of the abrasive wear resistance of coatings made in wet welding conditions with the use of two grades...
-
Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses
PublicationWire arc additive manufacturing (WAAM) is an additive manufacturing process based on the arc welding process in which wire is melted by an electric arc and deposited layer by layer. Due to the cost and rate benefits over powder-based additive manufacturing technologies and other alternative heat sources such as laser and electron beams, the process is currently receiving much attention in the industrial production sector. The gas...
-
Energetyczne wykorzystanie biomasy
PublicationW artykule przedstawiono energetyczne wykorzystanie biomasy jako alternatywy dla paliwa pierwotnego. Szczególną uwagę poświecono rodzajom, właściwościom i sposobom przygotowania biomasy do procesu spalania.Spalanie stanowi najstarszy sposób pozyskiwania energii z biomasy,jednak ze względu na technologiczno-ekonomiczne aspekty częściej wykorzystywany jest proces współspalania. Wzrost proekologicznej świadomości i rozwój lokalnego...
-
Energetyczne wykorzystanie biogazu
PublicationArtykuł przedstawia przegląd sposobów wykorzystania biogazu będącego jednym z odnawialnych źródeł energii. Pokazano uproszczony schemat pozyskiwania tego surowca. Przeanalizowany został skład biogazu oraz porównano typy odpadów, z jakich może zostać on uzyskany. Zaprezentowano również możliwości wykorzystania energii zawartej w biogazie.
-
Biogas Production in AnMBRs via Treatment of Municipal and Domestic Wastewater: Opportunities and Fouling Mitigation Strategies
Publication -
Effect of meteorological conditions on odour emission at biogas plants processing municipal waste – pilot research
Publication -
Odour Emissions of Municipal Waste Biogas Plants—Impact of Technological Factors, Air Temperature and Humidity
Publication -
Odour Nuisance at Municipal Waste Biogas Plants and the Effect of Feedstock Modification on the Circular Economy—A Review
Publication -
Absorptive Desulfurization of Model Biogas Stream Using Choline Chloride-Based Deep Eutectic Solvents
PublicationThe paper presents a synthesis of deep eutectic solvents (DESs) based on choline chloride (ChCl) as hydrogen bond acceptor and phenol (Ph), glycol ethylene (EG), and levulinic acid (Lev) as hydrogen bond donors in 1:2 molar ratio. DESs were successfully used as absorption solvents for removal of dimethyl disulfide (DMDS) from model biogas steam. Several parameters affecting the absorption capacity and absorption rate have been...
-
Investigation of praseodymium and samarium co-doped ceria as an anode catalyst for DIR-SOFC fueled by biogas
PublicationThe Pr and Sm co-doped ceria (with up to 20 mol.% of dopants) compounds were examined as catalytic layers on the surface of SOFC anode directly fed by biogas to increase a lifetime and the efficiency of commercially available DIR-SOFC without the usage of an external reformer. The XRD, SEM and EDX methods were used to investigate the structural properties and the composition of fabricated materials. Furthermore, the electrical...