Search
displaying 1000 best results Help
Search results for: CONTROLLERS PLACEMENT
-
Infraclavicular, Ultrasound-Guided Percutaneous Approach to the Axillary Artery for Arterial Catheter Placement: A Randomized Trial
Publication -
Proportional-Derivative and Model-Based Controllers for Control of a Variable Mass Manipulator
PublicationIn the paper, numerical analysis of dynamics of a variable mass manipulator is presented. A revolute joints composed manipulator is considered. Payload of the gripper is considered as the only element characterized by unknown value of its mass (variable between subsequent operations). As in other cases of the revolute joints composed manipulators, its behaviour dependents significantly on the pose of the manipulator. When the manipulator...
-
Robust design in delta domain for SISO plants: PI and PID controllers
PublicationW pracy przedstawiono zunifikowaną metodę numerycznie odpornej syntezy sterowników (regulatorów) działających w dyskretnym czasie w układach sterowania skalarnymi obiektami czasu ciągłego. Wykorzystano dyskretnoczasowe modele takich obiektów, oparte na tak zwanym operatorze delta, charakteryzującym się korzystnymi odpornościowymi cechami w przypadku stosowania dostatecznie małych wartości okresu próbkowania przetwarzanych sygnałów....
-
Proportional-derivative and Model-based Controllers for Control of a Variable Mass Manipulator
PublicationW artykule prezentowano wyniki analiza numeryczna dynamiki manipulatora o zmiennej masie. W skład manipulatora wchodzą jedynie członu i przeguby obrotowe. Ładowność chwytaka jest traktowana jako jedyny element o zmiennej masie. Podobnie jak w przypadku innych manipulatorów wyposażonych w przeguby obrotowe, parametry jego dynamika zależą od aktualnego ustawienia. Gdy przemieszczenia obejmują większy zakres roboczy, w równaniach...
-
Impregnation vibro-pressed concrete pavement bricks.
PublicationW materiałach przedstawiono wyniki badań uzyskanych podczas prób impregnacji wibroprasowanych elementów betonowych. Celem badań było określenie odpowiedniego składu kompozycji impregnacyjnej, aby uzyskać najlepszy efekt zabezpieczenia powierzchni betonu przed wnikaniem cieczy organicznych np. oleju mineralnego.
-
Asphalt pavement structure optimization with alternative materials
PublicationThe paper briefly describes modern method assessment of the pavement structure based on the simplified viscoelastic continuum damage (S-VECD) model. The method was used to compare two types of pavement structures. There were analysed classical cstructures with asphalt concretes with neat bitumen and innovative one- or two layered structures with SMA 16 with highly polymer modified bitumen (HiMA). Pavement structures using SMA 16...
-
Contribution of dynamic vehicle loads to pavement failure
PublicationPavement surfaces are not ideally even, which causes dynamic loads of vehicle axles. Distribution of dynamic loads of a given axle is similar to normal distribution and can be described by static load and dynamic load coefficient. The dynamic load coefficient depends on road profile, vehicle speed, properties of suspensions and static load of axle. While for a given road section road profile remains constant, vehicle speed and...
-
Pavement ageing influence on tyre/road noise
PublicationRoad surface should be constructed in a way that ensures safe and comfortable traffic conditions, not only when it is newly paved but also during its entire lifetime. An important factor in the asphalt mixture design process is also the expected pavement durability and stability of pavement properties over time. In many countries, road surface starts to play a significant role in traffic noise reduction actions. Selecting a particular...
-
Employing economical methods for pavement defects estimation
PublicationIt is a common practise that measurements of road surface conditions are made using professional and expensive apparatus. Typically a van or a truck equipped with a set of professional sensors i.e. laser scanners of surface is used, therefore the measurement update period is often quite long. Two alternative low-cost methods for estimating road pavement defects and failures were proposed and investigated by the authors. The first...
-
An optimised placement of the hard quality sensors for a robust monitoring of the chlorine concentration in drinking water distribution systems
PublicationThe problem of an optimised placement of the hard quality sensors in drinking water distribution systemsunder several water demand scenarios for a robust monitoring of the chlorine concentration is formulatedin this paper. The optimality is understood as achieving a desired trade off between the sensors and theirmaintenance costs and the accuracy of estimation of the chlorine concentration. The contribution of thiswork is a comprehensive...
-
Optimised Robust Placement of Hard Quality Sensors for Robust Monitoring of Quality in Drinking Water Distribution Systems
PublicationA problem of optimised robust placement of the hard quality sensors in Drinking Water Distribution Systems under several water demand scenarios for robust quality monitoring is formulated. Numerical algorithms to solve the problem are derived. The optimality is meant as achieving at the same time a desired trade off between the sensor capital and maintenance costs and resulting robust estimation accuracy of the monitoring algorithm...
-
Model Predictive Controller for Integrated Wastewater Treatment System
Publication -
Teaching Adaptive Control with DS1102 DSP Controller Board
Publication -
Adaptive neural voltage controller with tunable activation gain
PublicationW artykule przedstawiono model adaptacyjnego neuronowego regulatora napięcia dla turbogeneratora z nastrojonym współczynnikiem wzmocnienia funkcji przynależności. Ten model jest kombinacją klasycznego neuronowego modelu i neuronowego modelu z współczynnikiem wzmocnienia funkcji przynależności zależnym od warunków pracy obiektu.Przedstawiono, także wyniki symulacji mające na celu badania efektywności proponowanego regulatora dla...
-
Predictive current controller for sensorless induction motor drive
PublicationPrzedstawiono układ bezczujnikowego sterowania dla napedu z silnikiem klatkowym przy zastosowaniu predykcyjnego regulatora pradu. Zastosowany obserwator adaptacyjny wykazuje dużą odporność na zmiany parametrów silnika. W obserwatorze obliczane są wartości sił elektromotorycznych wykorzystywane w procesie regulacji predykcyjnej pradu silnika. Pokazano wyniki badań symulacyjnych i eksperymentalnych.
-
Quadrotor Flight Controller Design Using Classical Tools
PublicationA principal aspect of quadrocopter in-flight operation is to maintain the required attitude of the craft’s frame, which is done either automatically in the so-called supervised flight mode or manually during man-operated flight mode. This paper deals with the problem of flight controller (logical) structure and algorithm design dedicated for the man-operated flight mode. The role of the controller is to stabilise the rotational...
-
Intelligent turbogenerator controller based on artifical neural network
PublicationThe paper presents a desing of an intelligent controller based on neural network (ICNN). The ICNN ensures at the same time two fundamental functions : the maintaining of generator voltage at the desired value and the damping of the electromechanical oscillations. Its performance is evaluted on a single machine infinite bus power system through computer simulations. The dynamic and transient operation of the proposed controller...
-
Model predictive controller for integrated wastewater treatment systems.
PublicationSterowanie optymalizujace systemem oczyszczania ścieków (WWTS) pozwala na zmniejszenie kosztów operacyjnych przy jednoczesnym spełnieniu narzuconych ograniczeń na wypływające ścieki, jednak wymaga zaawansowanych technologii sterowania. Sterowanie predykcyjne z modelem (MPC) jest bardzo użyteczną technologią sterowania takimi systemami. MPC doskonale radzi sobie z obecnością ogrniczeń na wielkości wyjściowe, wielowymiarowością problemu...
-
Integrated controller for ultra high frequency technique laboratory
PublicationDepartment of Microwave and Antenna Engineering decided to modernize the laboratory of Ultra High Frequency Techniques. The main change was to replace measurement of the field distribution inside rectangular waveguides by analysing the fields around striplines. This involved the need to overcome several technical and conceptual problems. Precise positioning of the probe and reading the field distribution near the stripline is important...
-
Designing a ship course controller by applying the adaptivebackstepping method
PublicationThe article discusses the problem of designing a proper and efficient adaptive course-keeping control system for a seagoingship based on the adaptive backstepping method. The proposed controller in the design stage takes into account thedynamic properties of the steering gear and the full nonlinear static maneuvering characteristic. The adjustable parametersof the achieved nonlinear control structure were tuned up by using the...
-
Measurement system based on USB Z-Wave controller
PublicationA wireless measurement system based on the Z-Wave standard is presented in this paper. The system is composed of a U SB Z-Stick Gen5 controller connected to a Personal Computer and a Fibaro controller FGRGBWM-441. Operation of the system is controlled by software written in C++ using OpenZWave library. Some metrological aspects of the system are evaluated: accuracy, linearity, resolution and frequency of voltage measurements.
-
Speech synthesis controlled by eye gazing
PublicationA method of communication based on eye gaze controlling is presented. Investigations of using gaze tracking have been carried out in various context applications. The solution proposed in the paper could be referred to as ''talking by eyes'' providing an innovative approach in the domain of speech synthesis. The application proposed is dedicated to disabled people, especially to persons in a so-called locked-in syndrome who cannot...
-
Controlled English Interface for Knowledge Bases
PublicationThis paper describes the approach to interface for OWL Knowledge Bases based on Controlled English that is transformed directly to OWL 2 expressions and back. Two possible modes enable usage of the interface to specify Terminology, World Description as well as Integrity Constrains. Knowledge Base then can be validated against the Integrity Constrains to enable its continuous validation.
-
Comparison of Different Course Controllers of Biomimetic Underwater Vehicle with Two Tail Fins
Publication -
Experimental test results of an automatic voltage regulator with independent phase voltage controllers
PublicationThe growing number of distributed renewable energy sources and dynamic constant-power loads (e.g. electric vehicle charging stations) pose new challenges for network operators. These changes result in alterations to network load profiles and load flows, leading to greater voltage volatility. One effective solution to these problems can be the use of automatic voltage regulators (AVRs), which stabilize and symmetrize voltage output,...
-
Model reference method and continuous-time system identification in tuning the PID controllers.
PublicationW pracy opisano zagadnienie doboru nastaw sterowników PID w układach regulacji automatycznej. W rozważaniach wzięto pod uwagę zarówno klasyczną strukturę jednopętlowego układu sterowania z regulatorem PID umieszczonym w torze głównym, jak też odmienną realizację I-PD z członem całkującym występującym w torze głównym i sterownikiem proporcjonalno-różniczkującym ulokowanym w dodatkowej pętli sprzężenia zwrotnego. Ponieważ powszechnie...
-
Tire camber angle influence on tire-pavement noise
PublicationTaking into account tire-pavement noise and tires classification with respect to noise emission special measurement methods are usually used. When two of them are applied (the Laboratory Drum Method (DR) and the Close-Proximity Method (CPX)) the investigator has to be sure that the position of the tire is correct. The authors of this paper thought about tire position as tire (wheel) alignment in particular tire camber angle. They...
-
Evaluation of Pavement Temperatures in Poland During Winter Conditions
PublicationThe paper presents the analysis of pavement temperatures from meteorological stations located at the Polish national roads during the impact of low winter temperatures. Presented issue is particularly important in view of the problem of low-temperature cracks that occur in the asphalt pavement under the influence of low temperatures. For each location of meteorological station there were analysed measurements of the temperature...
-
The best porous asphalt pavement in Sweden so far
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Influence of Road Wetness on Tire-Pavement Rolling Resistance
PublicationRolling resistance of tires is one of the most important factors influencing energy consumption of road vehicles, especially on rural roads. For practical reasons, most of rolling resistance measurements are usually performed for dry road conditions. Based on the fact that roads are wet during a considerable time over the year and as part of the projects MIRIAM, ROLRES and ROSANNE, the TUG (Technical University of Gdańsk) in Poland...
-
Effects of the replacement of wheat flour with cricket powder on the characteristics of muffins
Publication -
Selected Aspects of 3D Printing for Emergency Replacement of Structural Elements
PublicationThe paper presents a synthetic characterization of modern methods of manufacturing or regenerating machine elements. Considered methods are machining and additive methods, in particular 3D printing in the FDM/FFF technique. For the study, the authors made samples of the holder bracket using selected methods. Samples made by machining operations, 3D printing with various filling were tested. The paper contains a technical and economic...
-
Management of MV/LV Transformer Replacement Based on AMI Platform
PublicationThe paper presents the extended possibilities of managing the selection and replacement of MV/LV transformers using the measurement data from the Advanced Metering Infrastructure (AMI) system. The analysis was conducted on samples of over 1900 transformers that operate in two different types of MV grids: rural and urban. The analysis has shown that there is a great potential in the field of optimizing the rated power of the transformers.
-
CURRENT CONTROLLED TRIALS IN CARDIOVASCULAR MEDICINE
Journals -
FPGA-based cavity simulator and controller for TESLA test facility
Publication -
The excitation controller with gain scheduling mechanism for synchronous generator control
PublicationThe power systems, including the synchronous generators and power systems networks, are complex nonlinear systems with configuration and parameters which change through time. That leads to electromechanical oscillations occurring in that system. Thus synchronous generator excitation controller must be capable of providing appropriate stabilization signal over broad range of operating conditions and disturbances. In this paper,...
-
Adaptacyjny regulator transformatora blokowego = Adaptive controller of generator transformer
PublicationW referacie przedstawiono koncepcję adaptacyjnego regulatora transformatora blokowego jako narzędzia do rozszerzenia ograniczeń generacji mocy biernej generatora synchronicznego.
-
PM Motor Controller for an Electric Vehicle with Separate Wheel Drives
PublicationDla pojazdu z elektrycznym niezależnym napędem kół, przedstawiono propozycję hierarchicznej struktury sprzętowej, z jednostką centralną koordynującą sterowanie poszczególnymi silnikami przez sterowniki podporządkowane, realizujące regulację momentu silnika w trybie rozruchu i hamowania. Zaproponowano algorytmy sterowania silnikiem synchronicznym z magnesami trwałymi, a także protokół komunikacji między sterownikami. Przedstawiono...
-
Speed sensorless induction motor drive with predictive current controller
PublicationToday, speed sensorless modes of operation are becoming standard solutions in the area of electric drives. This paper presents a speed sensorless control system of an induction motor with a predictive current controller. A closed-loop estimation system with robustness against motor parameter variation is used for the control approach. The proposed algorithm has been implemented using field-programmable gate arrays (FPGAs) and a...
-
Synthesis of a state feedback controller for an averaging tank with variable filling
PublicationIn paper, a nonlinear averaging tank with variable filling is considered. The main purpose of this research work was the modelling and control system synthesis of an averaging tank. The control objectives included ensuring stability and zero steady-state error of the system and achieving settling time as short as possible, while maintaining a minimal overshoot. In order to achieve the intended purpose, firstly a mathematical model...
-
The distributed model predictive controller for the nuclear power plant turbo-generator set
PublicationTypically there are two main control loops with PI controllers operating at each turbo-generator set. In this paper a distributed model predictive controller DMPC, with local QDMC controllers for the turbine generator, is proposed instead of a typical PI controllers. The local QDMC controllers utilize step-response models for the controlled system components. These models parameters are determined based on the proposed black-box...
-
Piotr Jaskuła dr hab. inż.
PeopleI am a Faculty member (Associate Professor, Highway and Transportation Research Department) at the Faculty of Civil and Environmental Engineering, Gdansk University of Technology, Poland).My main research interests include: pavement structures, interlayer bonding, pavement materials, recycling of road pavements, asphalt mixtures, bitumens, construction and maintenance of pavement structures.My lectures at the University include:...
-
Machine Learning and Text Analysis in an Artificial Intelligent System for the Training of Air Traffic Controllers
PublicationThis chapter presents the application of new information technology in education for the training of air traffic controllers (ATCs). Machine learning, multi-criteria decision analysis, and text analysis as the methods of artificial intelligence for ATCs training have been described. The authors have made an analysis of the International Civil Aviation Organization documents for modern principles of ATCs education. The prototype...
-
International Journal of Pavement Research and Technology
Journals -
Recent progress in controlled carbonization of (waste) polymers
Publication -
Preparation of silver nanoparticles with controlled particle size
PublicationNanocząstki srebra wykazują zdolność absorpcji promieniowania widzialnego, która jest efektem istnienia powierzchniowego plazmonu. W zależności od kształtu i wielkości cząstek obserwuje się różną barwę koloidów srebra. W wyniku przeprowadzonych badań otrzymano nanocząstki srebra metodą chemicznej redukcji. Zaobserwowano wpływ rodzaju reduktora (kwas askorbinowy, borowodorek sodu), stabilizatora (PVP, PVA) oraz prekursora srebra...
-
Implementation of power transformer controlled switching algorithm
PublicationThe article presents two new algorithms of controlled switching the power transformer. The main aim of the paper is to obtain formulas that determine the moments of closing of the circuit breaker poles. The study contains projects of control systems for both algorithms. Mathematical formulas for the time instants of the breaker poles closing were developed on the basis of electric circuit theory and magnetic circuit theory. The...
-
Characterization of carbon deposit with controlled carburization degree
Publication -
Music Mixing Process Controlled by Hand Gestures
PublicationW referacie przedstawiono system umożliwiający sterowanie procesami miksowania śladów nagrania muzycznego za pomocą gestów rąk. Przybliżono podstawy wielomodalnej percepcji argumentujące potrzebę powstania tego typu systemu oraz założenia przyjęte w trakcie jego tworzenia. Część sprzętowa systemu składa się z rzutnika multimedialnego, kamery internetowej, komputera klasy PC z zainstalowanym oprogramowaniem systemu oraz ekranu dla...
-
Novel digitally controlled drive for the vibratory conveyors
PublicationThe presented vibratory conveyors is used in the industry for continuous transportation of loose substances over short distances (2-10 m). The conveyor is applied for transportation in aseptic conditions. To obtain high efficiency for granulatedmass with different size of grain and different physical properties it is necessary to set the appropriate vibration amplitudeindependently of vibration frequency. This is not possible with...