Filters
total: 1939
-
Catalog
displaying 1000 best results Help
Search results for: FUEL SPRAY
-
Protection of bridges against stray current corrosion
PublicationA case study of Siennicki Bridge stray current corrosion hazard is presented. A corrosion risk was caused by incorrectly designed tram line traction which goes over the bridge. No dielectric insulation between running rails and bridge steel construction was used. A variety of protection methods against stray currents are described. Characteristics of the endangered bridge were described. Impressed current cathodic protection system...
-
EXPERIMENTAL RESEARCH ON INFLUENCE OF THE FUEL NOZZLE GEOMETRY ON THE FUEL CONSUMPTION OF THE MARINE 4-STROKE DIESEL ENGINE
PublicationThe article presents experimental research that has been carried out on a marine, 4-stroke, 3-cylinder, turbocharged engine. During testing, the engine operated at a constant rotational speed of 750 rpm and a load from 0 kW to 280 kW. The engine was fuelled by diesel oil of known specification and loaded by electric generator with water resistance. The fuel consumption was measured during the engine operation with fuel nozzles...
-
Impedance monitoring of fuel cell stacks
Publication -
Impedance monitoring of fuel cell stacks
PublicationThis paper presents an innovative, electrochemical impedance method for monitoring of electrochemical behaviour of a multi-cell, direct methanol fuel cell (DMFC) device. This method not only provides classical voltage changes at successive cells but also allows their detailed impedance behaviour to be presented. Impedance characteristics of individual cells within a fuel cell stack (depending on actual operating conditions) are...
-
Estimation of vehicle operational fuel consumption
PublicationW pracy przedstawiono metodę umożliwiającą wyznaczenie referencyjnego zużycia paliwa dla zarejestrowanych warunków eksploatacji. Warunki eksploatacji opisane są rozkładem energochłonności jednostkowej, która obejmuje zarówno wpływ warunków zewnętrznych jak również styl jazdy kierowcy. W pracy przedstawiono zestawienie wyników uzyskanych dla przejazdów wykonanych na terenie Gdańska, w regularnym ruchu miejskim. Przedstawiono także...
-
Perovskites in Solid Oxide Fuel Cells
PublicationPrzeglądowa publikacja dotycząca wykorzystania ceramicznych materiałów perowskitowych w tlenkowych ogniwach paliwowych.
-
Denitrification Process Enhancement and Diversity of the Denitrifying Community in the Full Scale Activated Sludge System after Adaptation to Fusel Oil
PublicationImplementation of anaerobic digestion of primary sludge in modern wastewater treatment plants (WWTPs) limits the availability of organic carbon for denitrification in conventional nitrification-denitrification (N/DN) systems. In order to ensure efficient denitrification, dosage of the external carbon source is commonly undertaken. However, application of commercial products, such us ethanol or acetate, greatly increases operational...
-
CO2 capture through direct-contact condensation in a spray ejector condenser and T- junction separator
PublicationThe design principle underlying the steam condensation and CO2 purification in a gas power plant with a focus on reducing CO2 emissions encompasses the deployment of a spray ejector condenser (SEC) and separator. This innovative system facilitates direct-contact condensation of steam with non-condensable gas (CO2) by inter acting with a spray of subcooled water, seamlessly integrated with a T-junction separator mechanism aimed...
-
Some Aspects of Potential Measurements in a Stray Current Field
Publication -
Reforma papieskich instytucji do spraw komunikacji społecznej
Publication -
Emission of CO2 and Fuel Consumption for Automotive Vehicles
Publication -
Performance of the methanol PEM fuel cell module
PublicationPrzedstawiono charakterystyki układu zasilania składającego się z dwóch ogniw paliwowych o mocy 1.2 kW każde. Układ był zasilany metanolem, który podlegał procesowi reformowania w reformerze firmy Genesis Fueltech. Sprawność reformera wzrastała od 33% dla obciążenia minimalnego do 78% przy obciążeniu maksymalnym. Czystość uzyskiwanego wodoru była satysfakcjonująca w całym zakresie pracy reformera.
-
Influence of traffic conditions on the operating fuel consumption
PublicationPrzedstawiona w pracy metoda umożliwia ocenę warunków eksploatacji pojazdu. Warunki te mogą wynikać zarówno z lokalnej specyfiki ruchu pojazdów jak również ze sposobu prowadzenia auta przez kierowcę. W pracy zamieszczono przykłady oceny zarejestrowanych w normalnej eksploatacji warunków ruchu pojazdu i ich wpływu na przebiegowe zużycie paliwa.
-
Review on electrolyte ceramic materials for fuel cells
PublicationPublikacja stanowi przegląd materiałów wykorzystywanych w tlenkowych ogniwach paliwowych ze szczególnym uwzględnieniem materiałów elektrolitowych.
-
Fuel systems of high power stationary engine
PublicationThe use of alternative fuels and, in the future, synthetic fuels has forced changes in the design of fuel supply systems in internal combustion engines. When operating a stationary engine at constant load, the possibility of using lean fuel mixtures appears. The selection of a precise operating mixture ignition system requires changes in traditional fuel systems. The article presents the current designs of fuel supply systems and...
-
Heterotrophic Anodic Denitrification in Microbial Fuel Cells
PublicationNowadays, pollution caused by energy production systems is a major environmental concern. Therefore, the development of sustainable energy sources is required. Amongst others, the microbial fuel cell (MFC) seems to be a possible solution because it can produce clean energy at the same time that waste is stabilized. Unfortunately, mainly due to industrial discharges, the wastes could contain nitrates, or nitrates precursors such...
-
9 - Solid oxide fuel and electrolysis cells
PublicationIn this chapter, the fundamental reactions, the geometrical designs, the material requirements, and the status of SOFCs and SOECs are presented. In the following seven chapters, the most important components of an SOC are described and the chapter ends with a summary and outlook. The described components are: (i) oxygen-ion conductors (electrolyte), (ii) anode materials for SOFCs (cathode in SOEC mode), (iii) cathode materials...
-
Ceramic composites for single-layer fuel cells
PublicationComposite materials consisting of acceptor doped lanthanum orthoniobate electrolyte phase (La0.98Ca0.02NbO4) and Li2O:NiO:ZnO semiconducting phase were synthesized. The precursor powder of La0.98Ca0.02NbO4 was prepared in nanocrystalline (mechanosynthesis) and microcrystalline (solid-state synthesis) form. The composite can be applied in a single-layer fuel cell, because of the presence of two phases acting as an anode and a cathode...
-
Degradation of xylose using a microbial fuel cell
PublicationIt is generally known, that many kind of microorganisms are capable of using carbohydrates as a source of carbon and energy in an environment. The biodegradation process of monosaccharides from pentoses (in this case- racemic mixture of D - and L – xylose) is an immense opportunity for an entire reduction of biological contamination to neutral compounds through MFC. The process is occurred in a single-chamber MFC, which is contained...
-
A novel concept of enhanced direct-contact condensation of vapour- inert gas mixture in a spray ejector condenser
PublicationAn analytical model of direct steam condensation (DCC) in the novel idea of spray ejector condenser (SEC) in the presence of inert gas has been developed. It is based on continuity, momentum and energy equations for the steam-carbon dioxide mixture and direct contact condensation mechanisms due to heat transfer and concentration. Crucial in the process of DCC is atomisation of the motive fluid in the ejector. The effect of atomised...
-
The importance of individual spray properties in performance improvement of a urea-SCR system employing flash-boiling injection
PublicationThe appropriate mixing of a urea–water solution (UWS) with exhaust gases in a selective catalytic reduction system is crucial to efficiently reduce nitrogen oxides and diminish the deposition of liquid wall film. One of the methods to enhance the mixing of the UWS with the exhaust gases is a flash-boiling injection. Its positive effect has been linked with a reduced Sauter mean diameter (SMD) and improved evaporation, but the...
-
Fuel cell noise data
Open Research DataMeasurement data of Hydrogen PEM fuel cels. The voltage fluctuations were measured over single cels of stack of 10 cels.
-
Jerzy Kowalski dr hab. inż.
People -
Case Study of Stray Current Corrosion of Tall Ship Mast
PublicationNowadays, in the present technical civilization there are numerous complex technical systems that may generate various hazards. Large transport units like ships can be considered as the most dangerous systems. Therefore, it is important to eliminate all possible hazards, especially for ship crewmembers. Destruction of ship structural components caused by vast corrosion is one of these hazards. Usually, its activity leads to a decrease...
-
JAKOŚĆ KSZTAŁCENIA W EDUKACJI SPECJALISTÓWDO SPRAW BEZPECZEŃSTWA WEWNĘTRZNEGO
PublicationPRZEDSTAWIONO WYBRANE ASPEKTYJAKOŚCI KSZTAŁCENIA SPECJALISTÓW DS. BEZPIECZEŃSTWA WEWN.
-
Improvement of Oxygen Electrode Performance of Intermediate Temperature Solid Oxide Cells by Spray Pyrolysis Deposited Active Layers
PublicationIntermediate temperature solid oxide fuel cells oxygen electrodes are modified by active interfacial layers. Spray pyrolysis is used to produce thin (≈500 nm) layers of mixed ionic and electronic conductors: Sm0.5Sr0.5CoO3−δ (SSC), La0.6Sr0.4CoO3−δ (LSC), La0.6Sr0.4Co0.2Fe0.8O3−δ (LSCF), and Pr6O11 (PrOx) on the electrode–electrolyte interface. The influence of the annealing temperature on the electrode polarization (area specific...
-
Direct-contact condensation from vapour- gas mixture in a spray ejector condenser for negative CO2 power plant
PublicationDirect-contact condensation of vapour containing the inert gas on a spray of subcooled liquid exists in a number of technical applications. For example, it may be found in the nuclear industry (e.g. pressurized jet under normal operating conditions, in safety analyses) or in the chemical industry (e.g. mixing-type heat exchanger, degasser, sea water desalting). The problem is also essential to modelling and analysis of some...
-
Evaluation of structural and electrical properties of multicomponent spinel oxide thin films deposited via spray pyrolysis technique
PublicationThis work reports the preparation of (Mn,Co,Fe,Ni,Cr)3O4 high-entropy spinel oxide in the form of a ~ 500 nm thin film utilising a facile spray pyrolysis technique. The structural and electrical properties of the layers were characterised after exposure to temperatures in the range of 400–900 ◦C. The as-deposited layers were amorphous, and crystallised upon heat treatment at 500 ◦C. Microstructural analyses proved a homogeneous...
-
Production of tropane alkaloids in Hyoscyamus niger (black henbane) hairy roots grown in bubble-column and spray bioreactors
PublicationHairy root cultures of Hyoscyamus niger were cultivated in shake-flasks, a bubble-column bioreactor and a hybrid bubble-column/spray bioreactor and evaluated for alkaloid production.
-
Marine Fuel Sulphur Limit Impact on Air Pollution
PublicationThe article presents calculation of Sulphur oxides percentage drop rate in marine industry recorded after 01.01.2020 when new limits, provided by International Maritime Organizations legislation, became effective. Ships’ SOx global emission was estimated and compared between 4th quarter 2019 and 1st quarter 2020. For more accurate estimation 3 seaside cities with big harbors were selected for statistical analysis. Noticeable...
-
The Influence of External Load on the Performance of Microbial Fuel Cells
PublicationIn this work, the effect of the external load on the current and power generation, as well as on the pollutant removal by microbial fuel cells (MFCs), has been studied by step-wise modifying the external load. The load changes included a direct scan, in which the external resistance was increased from 120 Ω to 3300 Ω, and a subsequent reverse scan, in which the external resistance was decreased back to 120 Ω. The reduction in the...
-
Protonic Ceramic Fuel Cells as novel electrochemical devices
PublicationProton ceramic conductors are novel materials which are interesting from the application point of view. For example, Protonic Ceramic Fuel Cells (PCFCs) is a type of a solid oxide fuel cell, which uses proton ceramic conductors as an electrolyte. Scientists are looking for the most efficient materials for these devices. In recent years main focus has been put on the search for new proton and mixed proton-electron conductors which...
-
Tyre rolling resistance and its influence on fuel consumption
PublicationRolling resistance of tyres is one of the major resistive forces acting on any wheeled vehicle. Unfortunately, it is also one of the forces very difficult to measure. It is estimated that in certain traffic conditions (like for example constant speed driving with slow or moderate speed) so called Rolling Resistance Impact Factor may be as high as 0.3. This means that reduction of rolling resistance by 50% would lead to 15% of energy...
-
Dimethyl ether (DME) as potential environmental friendly fuel
Publication -
Micro solid oxide fuel cells and their fabrication methods
PublicationW pracy przedstawiono obecny stan badań związany z tlenkowymi microogniwami paliwowymi oraz metodami ich wytwarzania.
-
Properties of glass-ceramic for solid oxide fuel cells
PublicationW pracy przedstawiono właściwości krystalicznych pyro- i orto- krzemowych szkieł przygotowanych dla tlenkowych ogniw paliwowych. Zbadano rozszerzalnoność, ubytek masy, zmiany widm rentgenograficznych oraz widm impedancyjnych dla szkieł narażonych przez 60 dni na atmosfere ulteniajacą i redukująca w temperaturze 800C.
-
Micro solid oxide fuel cells and their fabrication methods
PublicationW pracy przedstawiono obecny stan badań i tendencje w rozwoju tlenkowych ogniw paliwowych.
-
Influence of stack temperature on PEM fuel cell performance
PublicationW pracy przedstawiono wpływ temperatury stosu na wydajność ogniwa paliwowego typu PEM dla zadanego obciążenia. Badania ogniwa paliwowego przeprowadzono dla sześciu temperatur pracy stosu z zakresu od 30 oC do 65 oC. Dla najwyższej temperatury stosu, tj. 65 oC, wydajność pracy ogniwa paliwowego była najwyższa. Wraz ze wzrostem temperatury stosu zarejestrowano spadek mocy ogniwa paliwowego od 1015 W dla temperatury 30 oC do 1004...
-
A novel technology of solid oxide fuel cell fabrication
PublicationW pracy przedstawiono metodę wytwarzania wartstw i materiałów elektroceramicznych. Metoda jest kombinacją metod nanoszenia szkieletu z proszków ceramicznych i prekursorów polimerowych. Umożliwia ona otrzymanie zarówno gęstych jak i porowatych warstw i materiałów jednorodnych oraz kompozytowych. W pracy przedstawiono przykłady struktur dla tlenkowych ogniw paliwowych.
-
Advanced XAS analysis for investigating fuel cell electrocatalysts
PublicationW pracy została zaprezentowana analiza XAFS nanocząstek platyny używanych jako materiał katalityczny w niskotemperaturowych ogniwach paliwowych. Analiza danych EXAFS została przeprowadzona za pomocą zaawansowanej metody GNXAS, w której wzięto pod uwagę rozkład rozmiaru granul nano-platyny i niejednorodność warstwy katalitycznej elektrody, badane za pomocą SEM (skaningowy mikroskop elektronowy), TEM (transmisyjny mikroskop elektronowy)...
-
Recent anode advances in Solid Oxide Fuel Cells
PublicationW pracy podsumowano bieżące doniesienia na temat potencjalnych materiałów anodowych dla wysokotemperaturowych tlenkowych ogniw paliwowych z uwzględnieniem wyników otrzymanych przez autora pracy.
-
Dimethyl ether (DME) as potential environmental friendly fuel
PublicationIn recent years, there has been a growing interest in replacing petroleum fuels with so-called second generation environmental friendly fuels. Compared to traditional petroleum fuels dimethyl ether (DME) could be used as a clean high-efficiency compression ignition fuel with reduced particulate matter (PM), sulfur oxides (SOx), hydrocarbons (HC), carbon monoxide (CO) as well as combustion noise. Compared to some of the other leading...
-
Solid oxide fuel cells for distributed energy generation
PublicationW pracy przedstawiono zasadę działania tlenkowego ogniwa paliwowego. Zaprezentowano wybrane problemy oraz rozwiązania technologiczne.
-
On-line Impedance Monitoring of Direct Methanol Fuel Cell
PublicationW niniejszej pracy została przedstawiona technika badawcza Dynamiczna Elektrochemiczna Spektroskopia Impedancyjna w obszarze badań ogniw paliwowych. Obiektem badań było ogniwo paliwowe zasilane bezpośrednio metanolem. Badano on-line wpływ zmian warunków pracy na globalną impedancję ogniwa. Podczas pomiarów zmianie ulegała temperatura, natężenia przepływu utleniacza oraz obciążenie.
-
DME as alternative fuel for compression ignition engines – a review
PublicationThe ecological issues and the depletion of crude oil, has led the researchers to seeking for non-petroleum based alternative fuels, along with more advanced combustion technologies, and after-treatment systems. The use of clean alternative fuels is the one of the most perspective method that aiming at resolving of the said issues. One of the promising alternative fuels that can be used as a clean highefficiency compression ignition...
-
STUDY ON THE RELATIONSHIP BETWEEN VEHICLE MAINTENANCE AND FUEL CONSUMPTION
PublicationA contemporary road vehicle (RV) is a rather complex system, consisting of a large number of subsystems, assemblies, units, and elements (parts). While operating, an RV interacts with the environment, and its elements interact with each other. Consequently, the properties (parameters) of these elements change in the process - hardness, roughness, size, relative position, gapping, etc. A partial solution to the presented problems...
-
Wpływ parametrów strugi paliwa wtryskiwanego do cylindra silnika okrętowego na początkową fazę rozpylania
PublicationPrzedmiotem rozprawy jest analiza procesu wtrysku oleju napędowego do cylindra silnika okrętowego z zapłonem samoczynnym i bezpośrednim wtryskiem paliwa. Analiza tego zagadnienia została przeprowadzona w aspekcie wpływu makro parametrów strugi na początkową fazę rozpylania oleju napędowego. Celem niniejszej pracy jest określenie wpływu współczynnika L/D (długość otworu/średnica) otworu wylotowego wtryskiwacza na zmianę charakterystyki...
-
Fuels and Lubes International
Journals -
Zeitschrift fuer Individualpsychologie
Journals -
Study of swimbladder morphometry of Baltic herring and sprat (development of measurement methodology)
PublicationEffective management of Baltic clupeids, which are valuable commercially and ecologically,requires the biomass control. The acoustical techniques are recognized as effective in fishstock assessment. The study of Baltic herring and sprat individual backscatteringcharacteristics is required for the accurate biomass estimation using acoustical techniques.The previous measurements demonstrated significant...