Filters
total: 1139
displaying 1000 best results Help
Search results for: SANDWICH BEAMS
-
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublicationOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
BEHAVIOR OF REINFORCED CONCRETE BEAMS CONTAINING LIGHTWEIGHT AGGREGATE IN THE TENSILE ZONE
Publication.
-
Structural Assessment of Reinforced Concrete Beams Incorporating Waste Plastic Straws
PublicationThe behavior of reinforced concrete beams containing fibers made of waste plastic straws (WPSs) under the three point bending test is examined. The effect of WPS fiber addition on the compressive and split tensile strength is reported. Four concrete mixes were prepared. The control mix PS-0 had a proportion of 1 cement: 1 sand: 2 coarse aggregate and a water cement ratio of 0.4. In the other three mixes PS-0.5, PS-1.5 and PS-3,...
-
Discussion - Experimental study of dapped–end beams subjected to inclined load
PublicationDiscussion - Experimental study of dapped–end beams subjected to inclined load
-
Investigation of influence of space mopdes interaction on nonlinear dynamics of sound beams
PublicationOperatory rzutu na mody są zdefiniowane w dynamice płynów trójwymiarowych. Zostały wyprowadzone równania ewolucyjne. Rezultaty obliczeń numerycznych przedstawione.
-
Cavitation erosion of steels processed by CO2 laser beams of various parameters.
PublicationPrzedstawiono wpływ parametrów przetapiania stali za pomocą wiązki lasera CO2 na jej własności kawitacyjne. Do badań użyto stali 45, 2H13 i OH18N9. Wyniki badań wskazują na znaczny wpływ parametrów przetapiania na poziom odporności kawitacyjnej stali.
-
Identification of discontinuites in composite rods and beams based on Lamb wave propagation
PublicationW pracy omówiono metodę identyfikacji typu nieciągłości w belkach i prętach kompozytowych, oparta o analizę zmain w propagacji fali Lamba.
-
Multi-scale modelling of concrete beams subjected to three-point bending
PublicationW artykule przedstawiono wyniki numeryczne MES dwuskalowego modelowania belek betonowych z nacięciem na poziomie skali makro i mezo. Obliczenia wykonano przy wykorzystaniu modelu degradacji sztywności z nielokalnym osłabieniem. Beton został opisany na poziomie skali mezo jako stochastyczny materiał 3-składnikowy złożony z kruszywa, zaczynu cementowego oraz stref kontaktu. Natomiast na poziomie skali makro został opisany jako materiał...
-
Investigations on strength and fracture in RC beams scaled along height or length
PublicationThe objective of the present paper is to identify experimentally and theoretically differing failure mechanisms in reinforced concrete beams subjected to four-point bending for a separate variation of the depth and length at the constant thickness. Experiments were performed on reinforced concrete beams under four-point bending. Different failure mechanisms included steel yielding, diagonal tension or shear- compression depending...
-
Experimental investigations of size effect in reinforced concrete beams failing by shear
PublicationW artykule omówiono wyniki doświadczalne efektu skali w zbrojonych betonowych belkach niszczących się przez ścinanie. Doświadczenia wykonano dla belek o różnych wymiarach ze zbrojeniem stalowym i bazaltowym. Podczas doświadczeń pomierzono siłę oraz szerokości lokalizacji i rys. Wyniki porównano z modelem skali wg Bazanta.
-
The congruence of mental models in entrepreneurial teams – implications for performance and satisfaction in teams operating in an emerging economy
PublicationPurpose – The paper aims to explore the relationship between the congruence of mental models held by the members of entrepreneurial teams operating in an emerging economy (Poland) and entrepreneurial outcomes (performance and satisfaction). Design/methodology/approach – The data obtained from 18 nascent and 20 established entrepreneurial teams was analysed to answer hypotheses. The research was quantitative and was conducted using...
-
Qiangjiguang Yu Lizishu/High Power Laser and Particle Beams
Journals -
Double wedge prism based beam deflector for precise laser beam steering
Publication -
On small signal capacitance spectra of organic diode formed by ITO-palladium phthalocyanine-Al sandwich system
PublicationPraca poświęcona jest widmom małosygnalowej pojemności w zakresie 25 Hz-1 MHz i charakterystyce prądowo-napięciowej planarnego układu utworzonego przez ITO/ftalocyanina palladu/Al.
-
Electric properties of an Au-CuPc-Au sandwich system: Direct current and low signal admittance studies
PublicationPraca przedstawia wyniki pomiarów stałoprądowych i niskosygnałowej admitancji układu złoto/ftalocyjanina miedzi/złoto. Obserwowana asymetria charakterystyk stałoprądowych sugeruje, że prąd elektryczny płynący przez układ jest prądem ograniczonym elektrodowo i wydajność wstrzykiwania dziur jest uwarunkowana kolejnością nanoszenia warstw. W przypadku wstrzykiwania dziur przez bardziej regularną międzypowierzchnię (tj. gdy ftalocyjanina...
-
Nowe konstrukcje przekładkowe metal-pianka poliuretanowa = New sandwich plate systems metal - PU foam
PublicationWyznaczono statyczne własności mechaniczne przy ściskaniu, rozciąganiu oraz ścinaniu w óżnych kierunkach względem wzrostu piany oraz przy cyklicznych naprężeniach ściskających i ścinających. Stwierdzono różnice własności mechanicznych w zależności od kierunku i formy naprężeń.
-
Sandwich-like mesoporous silica flakes for anticancer drug transport—Synthesis, characterization and kinetics release study
Publication -
In vitro and in vivo evaluation of sandwich-like mesoporous silica nanoflakes as promising anticancer drug delivery system
Publication -
A novel sandwich footbridge - Practical application of laminated composites in bridge design and in situ measurements of static response
PublicationA novel sandwich composite footbridge is presented in the paper, as an example of practical application of laminated composites in civil engineering. The in situ static load tests of the footbridge before its acceptation for exploitation are shown and discussed. The results are compared with the corresponding ones from a numerical equivalent single layer model of the sandwich structure created within the framework of finite element...
-
Stalowe panele typu SANDWICH - nowe elementy konstrukcji statku. IX Krajowa Konferencja Mechaniki Pękania.
PublicationPrzedstawiono ideę zastosowania do konstrukcji kadłuba statku stalowego panelu typu Sandwich. Panele te mogą być użyte na konstrukcje pokładów, grodzic czy ścianek. Jednakże aby mogły być stosowane w konstrukcji kadłuba, należy posiadać informacje na temat ich własności technologiczno-wytrzymałościowych. W referacie przedstawiono badania laboratoryjne paneli SANDWICH prowadzone w Katedrze Technologii Okrętów, Systemów Jakości...
-
COMPARATIVE STUDY OF TRADITIONAL AND VIRTUAL TEAMS
PublicationThe paper presents two kinds of cooperating teams: traditional and virtual, and proposes a new measure of the team virtuality level. Some representative teamwork characteristics, such as team member competencies, team diversity, leadership, and team decision-making are analyzed and compared depending on the degree of virtuality. Moreover, the team climate as one of the team performance measures is also analyzed and compared in...
-
Trust triggers and barriers in intercultural teams
PublicationIntercultural teams are more and more popular nowadays — they constitute a serious challenge in terms of effective cooperation and trust building, however. The article presents the potential problems that can affect intercultural cooperation and stresses the power of trust in cultural diversity conditions. The ten-factor model of intercultural team trust is presented. The main aim was to answer the questions: what are the differences...
-
The preferable ways of decision-making in IT teams
PublicationSoftware development team collaboration requires various decisions regarding essential aspects of a project’s progress. General and particular decision-making models are considered, and their main aspects such as team types, problem solving categories, and decision-making ways are analyzed. The research concerns representative groups of IT specialists and their preferences in decision-making are investigated. Four possible cases were...
-
Zastosowanie stalowych paneli typu sandwicz w konstrukcjach okrętowych i oceanotechnicznych
Publication---do uzupełnienia--------------
-
Time Projection Chamber (TPC) detectors for nuclear astrophysics studies with gamma beams
Publication -
Static analysis of grids assembled with thin-walled beams of the open cross-section
PublicationPraca dotyczny analizy statycznej rusztów zbudowanych z prętów cienkościennych. Przedstawiono w niej koncepcję metody modelowania konstrukcji dźwigarów cienkościennych i rusztów z wykorzystaniem superelementów w połączeniu z klasyczną teorią belek cienkościennych o przekroju nieodkształcalnym. Zamieszczono wyniki przeprowadzonej eksperymentalnej weryfikacji badań teoretycznych.
-
A Diagnostic Method Based on Deflection Analysis for Monitoring Post-elastic Response of Beams
PublicationA non-destructive diagnostic method based on deflection analysis for monitoring the post-elastic response of beams was developed, and a diagnostic indicator was proposed. The indicator was defined as the second moment of the normalised curvature function about the mid-span, where the curvature was computed from the normalised deflection function. Elastic reference values of the indicator were computed for simply supported beams...
-
THE METHOD OF ANALYSIS OF DAMAGE REINFORCED CONCRETE BEAMS USING TERRESTRIAL LASER SCANNING
PublicationThe authors present an analysis of the possibility to assess deformations and mode of failure of R-C beams using terrestrial laser scanning. As part of experiments carried out at the Regional Laboratory of Construction (at Gdansk University of Technology), reinforced concrete beams were subjected to destruction by bending and by shear. The process of press impact on the reinforced concrete beam was recorded using terrestrial laser...
-
The method of analysis of damage reinforced concrete beams using terrestial laser scanning
PublicationThe authors present an analysis of the possibility to assess deformations and mechanisms of destructing bent reinforced concrete beams using the terrestrial laser scanning. As part of the experiments carried out at the Regional Laboratory of Construction of the Concrete Structures Division of the Civil and Environmental Engineering Faculty at Gdansk University of Technology, the reinforced concrete beams were subjected to destruction...
-
Assessment of Wooden Beams from Historical Buildings Using Ultrasonic Transmission Tomography
PublicationThe main goal of this study was non-destructive evaluation of wooden elements using ultrasonic waves. The inspection was carried out on wooden beams from a historical object. Elastic wave signals were processed by ultrasonic transmission tomography to obtain imaging of the internal structure of tested elements without disturbing their state and integrity. The focus was on the influence of wood anisotropy on the propagation of ultrasonic...
-
An isogeometric finite element formulation for geometrically exact Timoshenko beams with extensible directors
PublicationAn isogeometric finite element formulation for geometrically and materially nonlinear Timoshenko beams is presented, which incorporates in-plane deformation of the cross-section described by two extensible director vectors. Since those directors belong to the space R3, a configuration can be additively updated. The developed formulation allows direct application of nonlinear three-dimensional constitutive equations without zero...
-
Nonlocalized thermal behavior of rotating micromachined beams under dynamic and thermodynamic loads
PublicationRotating micromachined beams are one of the most practical devices with several applications from power generation to aerospace industries. Moreover, recent advances in micromachining technology have led to huge interests in fabricating miniature turbines, gyroscopes and microsensors thanks to their high quality/reliability performances. To this end, this article is organized to examine the axial dynamic reaction of a rotating...
-
Neutral Dissociation of Pyridine Evoked by Irradiation of Ionized Atomic and Molecular Hydrogen Beams
PublicationThe interactions of ions with molecules and the determination of their dissociation patterns are challenging endeavors of fundamental importance for theoretical and experimental science. In particular, the investigations on bond-breaking and new bond-forming processes triggered by the ionic impact may shed light on the stellar wind interaction with interstellar media, ionic beam irradiations of the living cells, ion-track nanotechnology,...
-
Performance of isotropic constitutive laws in simulating failure mechanisms in scaled RC beams
PublicationResults of numerical calculations of reinforced concrete (RC) beams are presented. Based on experimental results on longitudinally reinforced specimens of different sizes and shapes are investigated. Four different continuum constitutive laws with isotropic softening are used: one defined within continuum damage mechanics, an elasto-plastic with the Rankine criterion in tension and the Drucker-Prager criterion in compression, a...
-
Spectral criterion of infinite fatigue life of beams under asymmetric random loads
PublicationRozpatrywana jest trwałość zmęczeniowa belek poddanych stałym i zmiennym obciążeniom osiowym, giętnym i skrętnym o znanych gęstościach widmowych mocy. Założono, że materiał posiada granicę zmęczenia i jest zgodny z modelem Kelvina-Voigta, oraz że składowe naprężenia są stacjonarne, stacjonarnie skorelowane i różniczkowalne w sensie średniokwadratowym. Zdefiniowano naprężenie równoważne i sformułowano kryterium nieograniczonej trwałości...
-
Characterization of corrosion in reinforced concrete beams using destructive and non-destructive tests
PublicationThe paper presents both non-destructive and destructive experimental tests on steel-reinforced concrete beams subjected to electrochemical corrosion. To examine the condition and behavior of the specimens, destructive tests were carried out, i.e., a three-point bending together with a modulated ultrasonic wave test. In addition, a series of non-destructive experiments were conducted, such as the potential measurement method, low-frequency...
-
Spectral criterion of infinite fatigue life of beams under combined random loads
PublicationRozpatrywana jest trwałość zmęczeniowa belek poddanych zmiennym obciążeniom osiowym, giętnym i skrętnym o znanych gęstościach widmowych mocy i zerowych wartościach średnich. Założono, że materiał posiada granicę zmęczenia i jest zgodny z modelem Kelvina-Voigta, oraz że składowe naprężenia są stacjonarne, stacjonarnie skorelowane i różniczkowalne w sensie średniokwadratowym. Zdefiniowano naprężenie równoważne i sformułowano kryterium...
-
Measurements and calculations of the width of the fracture process zones on the surface of notched concrete beams
PublicationArtykuł omawia wyniki pomiaru i analizy numerycznej szerokości strefy pękania w belkach betonowych z nacięciem. Do pomiarów zastosowano metodę DIC. Do symulacji zastosowano model sprężysto - plastyczny i model z degradacją sztywności. Oba modele zostały rozszerzone o nielokalne osłabienie. Wyniki symulacji porównano z doświadczeniami.
-
SIMULATIONS OF FRACTURE IN CONCRETE BEAMS UNDER BENDING USING A CONTINUUM AND DISCRETE APPROACH
PublicationThe paper describes two-dimensional meso-scale results of fracture in notched concrete beams under bending. Concrete was modelled as a random heterogeneous 4-phase material composed of aggregate particles, cement matrix, interfacial transitional zones and air voids. Within continuum mechanics, the simulations were carried out with the finite element method based on a isotropic damage constitutive model enhanced by a characteristic...
-
Experimental and numerical investigations on RC beams with stirrups scaled along height or length.
PublicationBelki żelbetowe (RC) ze zbrojeniem poprzecznym (strzemiona) poddane czteropunktowemu zginaniu zostały zbadane eksperymentalnie i numerycznie. Belki były skalowane wzdłuż wysokości lub długości. Były przezbrojone, aby uniknąć płynięcia zbrojenia podłużnego. W pierwszej kolejności przeprowadzono badania laboratoryjne na belkach żelbetowych ze strzemionami. Ze względu na brak podobieństwa geometrycznego zaobserwowano dwa odrębne tryby...
-
Wave propagation in delaminated beam
PublicationW pracy przedstawiono model oraz wyniki analizy propagacji fali sprezystejw belce z delaminacją.
-
Effects of manufacturing and face /core bonding on impact damage in glass/polyester - PVC foam core sandwich panels
PublicationZbadano podatność na inicjację uszkodzeń pod wpływem spadającego obciążenia w konstrukcjach przekładkowych poliestrowo szklanych z rdzeniem z pianki PVC przy dwóch sposobach łączenia okładek z rdzeniem: przy pomocy 2 klejów proponowanych do tego celu przez ich producentów oraz czystej żywicy. Zastosowano oprzyrządowany młot spadowy , określając rozmiar zniszczeń na powierzchni próbki metodą wizualna i ultradźwiękową. Inicjacja...
-
Określanie rozkładu odkształceń i naprężeń w złączach spawanych stalowych paneli typu sandwich metodą MES
PublicationRozwój technologii spawania laserowego umożliwił masową produkcję konstrukcji cienkościennych, w tym również stalowych paneli typu "Sandwich". Technologia wykonywania spoin łączących poszycia paneli z usztywnieniami powoduje powstanie połączenia o szczególnej geometrii i własnościach materiałowych. Złącza spawane laserowo, w porównaniu ze spoinami innego typu, charakteryzują się specyficznym sposobem zachowania pod obciążeniem...
-
Acoustic emission signals in concrete beams under 3-point bending (beams #1, #2, #3)
Open Research DataThe DataSet contains the results of the mechanical behaviour of concrete beams with dimensions 40 x 40 x 160 cm3under the 3-point bending. The beams were made of concrete with the following ingredients: cement CEM I 42.5R (330 kg/m3), aggregate 0/2 mm (710 kg/m3), aggregate 2/8 mm (664 kg/m3), aggregate 8/16 mm (500 kg/m3), water (165 kg/m3) and super-plasticizer...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-002)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-Con)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-004)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Ultrasonic wave propagation and digital image correlation measurements of polyolefin fibre-reinforced concrete beams under 3-point bending (beam B-006)
Open Research DataThe DataSet contains the results of the mechanical behaviour of a concrete beam under a 3-point bending test. The beams had dimensions 15 x 15 x 70 cm3. The beam B-Con was made of concrete without fibres (as the reference beam), while beams B-002, B-004, and B-006 were manufactured from the concrete mix containing 2 kg/m3, 4 kg/m3 and 6 kg/m3 of fibres,...
-
Application of continuous wavelet transform in vibration based damage detection method for beams and plates
PublicationW artykule zaprezentowano metodę lokalizacji uszkodzeń w konstrukcjach belkowych i płytowych bazującą na analizie falkowej. Wyznaczono postacie drgań badanych konstrukcji. Postacie drgań konstrukcji belkowej zostały przeanalizowane jednowymiarową transfrormatą falkową. Sformułowano dwuwymiarową transformatę falkową, którą zastosowano do postaci drgań konstrukcji płytowej.
-
Numerical studies on size effects in concrete beams. Architecture Civil Engineering Environment ACEE
PublicationW artykule przedstawiony wyniki obliczeń efektów skali w belkach betonowych podczas zginania. Zastosowano model sprężysto-plastyczny z nielokalnym osłabieniem. Rozkład wytrzymałości na rozciąganie był stochastyczny - przestrzennie skorelowany. Belki były geometrycznie podobne. Wyniki porównano z modelem efektu skali Bazanta.