Publications
Filters
total: 804
Catalog Publications
-
Comparative study of operation of condensing and traditional boilers equipped with the ORC module for electricity generation
PublicationCondensing technology applied to boilers is to make full use of thermal energy contained in the fuel. That means that additionaly the heat from condensation of exhaust gases can be used for the purposes of heating the domestic hot water and to cover the demand for central heating. The study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler....
-
Nucleate pool boiling on porous metallic coatings
PublicationPrzedstawiono wyniki systematycznych badań eksperymentalnych przejmowania ciepła podczas wrzenia pęcherzykowego wody destylowanej w stanie nasycenia od płaskich i cylindrycznych powierzchni o specjalnie przygotowanej powierzchni: gładkiej, chropowatej oraz pokrytej warstwą porowatą.
-
Modelling of two-component turbulent mass and heat transfer in air-fed pressurised suits
PublicationIn this paper the modelling of an important industrial problem is addressed, which involves the two-component turbulent flow with heat transfer that takes place inside protective clothing. The geometry of the flow boundaries is reconstructed in a CAD system from photogrammetry scan data. The overall model is sufficiently realistic to allow, after validation, design improvements to be tested. Those presented here allow the reduction...
-
Magazyny ciepła ze złożem naturalnym i złożem na bazie materiałów zmiennofazowych
PublicationW artykule zaprezentowano możliwości wykorzystania magazynowania energii w technologii budowlanej. Przedstawiono najnowsze trendy rozwoju tej technologii w oparciu o wykorzystanie materiałów zmiennofazowych oraz nowoczesnych materiałów konstrukcyjnych . Pokazano historyczne jak i najnowsze rozwiązania magazynów i obiektów budowlanych z nimi współpracujących. Autorzy dokonali swoistego przeglądu rozwiązań mogących mieć zastosowanie...
-
Nowe czynniki chłodnicze i zmiany w instalacjach chłodniczych. Cz.3
PublicationArtykuł jest kontynuacją tematyki przedstawionej w części pierwszej (nr 9 -2015) oraz części drugiej (nr 10-2015). Autorzy nawiązują do konsekwencji jakie niosą ze sobą ograniczenia stosowania syntetycznych czynników chłodniczych z grupy CFC i HFC. W artykule przedstawiono analizę wpływu rodzaju czynnika chłodniczego na efektywność sprężarkowego układu chłodzenia przeznaczonego do współpracy z komorą chłodniczą do przechowywania...
-
AN EXPERIMENTAL AND NUMERICAL STUDY ON THE PERFORMANCE OF AN INNOVATIVE VERTICAL-AXIS WIND TURBINE
PublicationThis paper introduces the innovative modification of the Savonius wind turbine being able to significantly increase efficiency in comparison with the classic design. This innovative design is equipped with a stator directing the flow. The presence of the stator increases the active surface area and generates higher torques acting on a shaft. Additionally, it makes it possible to take better advantage of wind energy and compensate...
-
ECU calibration for gaseous dual fuel supply system in compression ignition engines
PublicationThe dual fuel (DF) combustion mode is proven solution that allows to improve or get at the same level engine performance and reduce toxic compounds in exhaust gases which is confirmed by researchers and end-users. DF combustion mode uses two fuels gaseous fuel as a primary energy source and a pilot quantity of diesel fuel as ignition source. However, in order, to fully take advantage of the potential of the dual fuel mode, DF system...
-
The effect of reduced pressure on carbon dioxide flow boiling heat transfer in minichannels
Publication. In the paper presented are the results of the study on the effect of reduced pressure on flow boiling heat transfer data in minichannels as well as conventional ones. That effect renders that most of heat transfer correlations fail to return appropriate results of predictions. Mostly they have been developed for the reduced pressures from the range 0.1-0.3. The special correction has been postulated to the in-house model of flow...
-
The use of liquid crystal thermography TLC and particle image velocimetry PIV in selected technical applications
PublicationNowadays, the energy cost is very high and this problem is carried out to seek techniques for improvement of the aerothermal and thermal (heat flow) systems performances in different technical applications. The transient and steady-state techniques with liquid crystals for the surface temperature and heat transfer coefficient or Nusselt number distribution measurements have been developed. The flow pattern produced by transverse...
-
Simple Computational Methods in Predicting Limit Load of High-Strength Cold-Formed Sections due to Local Buckling: A Case Study
PublicationCold-formed thin-walled sections are prone to local buckling caused by residual stresses, geometrical imperfections and inconsistency of material properties. We present a real case of buckling failure and conduct a numerical and experimental study aimed to identify methods capable of predicting such failures. It is important because designers of structures are getting more FEA-oriented and tend to avoid lengthy procedures of cold-formed...
-
Pre-swirl energy saving device in marine application
PublicationThis paper covers topics of energy saving device (ESD) with application to marine propulsors. The form of ESD, considered in this paper, consists of fixed lifting foils mounted in front of the screw propeller (the pre-swirl stator/guide vanes). An algorithm for designing propulsion systems, consisting of guide vanes and screw propeller, is presented. The proposed method relies on hybrid lifting line (guide vanes)-lifting surface...
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublicationExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
-
Effect of Flow Normalization in Micro-Pin-Finned Heat Sink: Numerical Study
PublicationThe micro-pin-fin heat sink (MPFHS) is widely employed for the heat transfer enhancement of microchannel heat sinks. In the current paper, the effect of flow normalization on the thermohydraulic performance of micro-pin-finned heat sinks is studied numerically. Two geometries of MPFHSs, the conventional design micro-pin-fin heat sink (CD-MPFHS) with a uniform-width micro pin fin and the proposed design micro-pin-fin heat sink (PD-MPFHS)...
-
Experimental and theoretical study of dryout in annular flow in small diameter channels
PublicationW pracy zaprezentowano badania eksperymentalne kryzysu wrzenia II rodzaju w kanałach o małej średnicy. Badania prowadzone były w rurach pionowych o średnicy 1.15 i 2.3 mm, w których badanym czynnikiem były płyny niskowrzące, takie jak SES36 i R123. W badaniach zastosowano nowoczesne techniki pomiarowe do określania lokalizacji kryzysu wrzenia na ściance kanału, np. kamerę termowizyjną. Na podstawie pozyskanych punktów eksperymentalnych...
-
Carbon Dioxide Recovery Skid
PublicationIn the face of tightening climate regulations, the adoption of carbon dioxide recovery systems is inevitable. Modular process skid units have been widely adopted across the industry. The gas-steam power plant skid unit with the carbon dioxide recovery system was described. The proposed skid module consists of the compact cycle with the oxy-combustion and the carbon dioxide capture skid unit producing pure compressed CO2. The compactness...
-
Comparison of predictive methods for flow boiling heat transfer in conventional channels and minichannels - the effect of reduced pressure
PublicationIn the paper are presented the results of follow on studies from [1]–[3] using authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data collected from various researchers to investigate the sensitivity of the in-house developed model. The collected experimental data came from various studies from literature and were conducted for the full...
-
Dynamic characteristics of the proton exchange membrane fuel cell module
PublicationThe paper describes a fuel cell based system and its performance. The system is based on two fuel cell units, DC/DC converter, DC/AC inverter, microprocessor control unit, load unit, bottled hydrogen supply system and a set of measurement instruments. In the study presented in the paper a dynamic response of the proton exchange membrane (PEM) fuel cell system to unit step change load as well as to periodical load changing cycles...
-
LCT, PIV and IR Imaging Detection in Selected Technical and Biomedical Applications
PublicationThermochromic liquid crystals (TLC), Particle Image Velocimetry (PIV) and Infrared Imaging Themography (IR) have been successfully used in non-intrusive technical, industrial and biomedical studies and applications. These four tools (based on the desktop computers) have come together during the past two decades to produce a powerful advanced experimental technique as a judgment of quality of information that cannot be obtained...
-
An improved method for flow boiling heat transfer with account of the reduced pressure effect
PublicationIn the paper are presented the results using the authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data to investigate the sensitivity of the in-house developed model. In the work are presented the results of calculations obtained using the semi-empirical model on selected experimental flow boiling data of the refrigerants: R134a, R1234yf,...
-
COMPARISON OF PREDICTIVE METHODS FOR FLOW BOILING HEAT TRANSFER IN CONVENTIONAL CHANNELS AND MINICHANNELS – THE EFFECT OF REDUCED PRESSURE
PublicationIn the paper are presented the results of follow on studies from [1]–[3] using authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data collected from various researchers to investigate the sensitivity of the in-house developed model. The collected experimental data came from various studies from literature and were conducted for the full...
-
Experimental and comparative study on the two-phase pressure drop of air-water mixture in U-bend and straight pipe annuli
PublicationIn this paper, the experimental and theoretical analysis of pressure drop in singlephase and two phase-flow were presented for straight and U-bend smooth tube annulus and tube annulus with wire coil insert. Experiments for various boundary conditions were performed. In case of U-tube and straight tube with and without turbulator, tests were made for the water-water and air-water systems. The study covered a wide measuring range,...
-
LCT, PIV and IR Imaging Detection in Selected Technical and Biomedical Applications
PublicationPaper presents the brief summary of the history of Thermochromic liquid crystals (TLC), Particle Image Velocimetry (PIV) and Infrared Imaging Themography (IR). Principal methods and tools are described and some examples are presented. With this objective, a new experimental technique have been developed and applied to the study of heat and mass transfer and for biomedical diagnosis. Selected results of experiments using these methods...
-
Comparative analysis of the theoretical models of ideal propulsor, ideal fluid brake, ideal screw propeller and ideal axial wind turbine
PublicationThe article presents a detailed discussion of four different fluid dynamics devices.These devices are presented with all relevant mathematical formulae regarding the forces, the power and the efficiency. It is demonstrated that application of the Betz theorem to axial wind turbines is not correct and it underestimates the maximujm achievable efficiency. This conclusion is supported by numerical calculations.
-
Working fluid selection for Organic Rankine Cycle applied to heat recovery systems
PublicationPrzedstawiono algorytm obliczeń sprawności systemu ORC na bazie dużej liczby cieczy organicznych.
-
The new concept of capillary forces aided evaporator for application in domestic organic rankine cycle
PublicationThis paper presents studies on the possibility of applying capillary forces induced in the porous structure to a modern design of evaporator. The potential application of such heat exchanger is for example an evaporator of the domestic micro combined heat and power (CHP) unit. One of the problems in the micro-CHP is excessive demand for pumping power. The proposed design helps in overcoming that issue. In the evaporator outlined...
-
Investigation of the aerodynamics of an innovative verticalaxis wind turbine
PublicationThis paper presents a preliminary three dimensional analysis of the transient aerodynamic phenomena occurring in the innovative modification of classic Savonius wind turbine. An attempt to explain the increased efficiency of the innovative design in comparison with the traditional solution is undertaken. Several vorticity measures such as enstrophy, absolute helicity and the integral of the velocity gradient tensor second invariant...
-
Smart heating system for home extending utilization of renewable energy sources
PublicationIn the paper a modern approach to smart home heating is presented. Proposed solution utilizes at least two low-polluting energy source technologies. The main idea is to connect well known ecological energy sources in a way that they can support each other and minimize risks of failure when using single system or even both of them but managed in separate way. Considered energy technologies, used separatelly, have disadvan-tages,...
-
Heat transfer intensification by jet impingement – numerical analysis using RANS approach
PublicationJet impingement is a method of the heat transfer enhancement applied in the engineering systems. The idea is to generate fast-flow fluid jet which impinge on the heated (or cooled) surface, causing significantly higher heat transfer rate. Although some flat surface jet impingement cases are described in the literature, the validated data is still limited. The reason is coming from the fact, that these flows are hydrodynamically...
-
The effectivness of fault detection in common rail injectors examination methods
PublicationThe article presents the effectiveness tests of fault detection in common rail injectors. 40 injectors with different wear levels were tested. Testing was made on two test benches of a completely different design. Research includes comparison of accuracy, reproducibility and testability to detect specific defects. A device was created for visualization of the fuel injector spraying steam.
-
Energetic model of hydraulic system of refuse collection vehicle based on simulation and experimental data
PublicationThis paper presents an energetic model of hydraulic system of a refuse collection vehicle. First, benefits resulting from implementation of an energetic model in the industry and operation of a Refuse Collection Vehicle are briefly explained. Then, components of the energy consumption in hydraulic circuits of compactor and lifting device are described and combined into a comprehensive model that can be evaluated using basic measurement...
-
Experimental determination of general characteristic of internal combustion engine using mobile test bench connected via Power Take-Off unit
PublicationThe general characteristics of the engine include information about the regions of the engine's operating area that are most efficient, where specific fuel consumption reaches the smallest values. Economic operation based on those characteristics can contribute to a significant reduction of fuel consumption and consequently less pollutant emissions and lower costs. The paper presents an experimental method of determination of general...
-
Modelling of heat transfer in supercritical pressure recuperators
PublicationIn the paper presented is analysis of convective flow heat transfer at supercritical pressure in channels of heat exchanger working in the thermodynamic cycle. The modelling is based on the division of the flow into three regions, namely the heavy fluid, a two phase flow consisting of the heavy and light fluids and finally the light fluid flow. Modelling is concentrated on the region of simultaneous flow of two fluids divided into...
-
Thermal energy storage using stearic acid as PCM material
PublicationThis work presents an experimental study of thermal energy storage by use of PCM. The aim of the study was to establish the influence of different inlet temperature of heat transfer fluid (HTF) and different Reynolds number of HTF on intensity of charging process. The PCM used in this study was stearic acid and water was used as HTF. A copper helical coil mounted in cylindrical container served as a heat transfer surface.
-
PRESSURE DROP OF HFE7000 AND HFE7100 IN FLOW CONDENSATION IN MINICHANNELS WITH ACCOUNT OF NON-ADIABATIC EFFECTS
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena involving the change of phase. There is a temptation to describe both these phenomena with one only correlation. From amongst the structures present in flow boiling and flow condensation at least the annular flow structure seems to be mostly appropriate to the common modeling. However, the shear stress acting between vapor phase and liquid...
-
Numerical prediction of steady and unsteady tip vortex cavitation on hydrofoils
PublicationArtykuł przedstawia metodę numeryczną do wyznaczania kawitujących wirów wierzchołkowych powstających za płatami nośnymi. Metoda ta jest oparta na rozwiązywanie dwufazowego turbulentnego przepływu cieczy lepkiej. Pozwala ona wyznaczyć geometrię kawitującego wiru dla różnych geometrii płata nośnego i dla różnych parametrów przepływu. Pokazano porównanie wyników obliczeń z pomiarami i rejestracjami wykonanymi na modelu płata w tunelu...
-
Analysis of start energy of Stirling engine type alpha
PublicationThe Stirling engine type alpha is composed of two cylinders (expansion space E and compression space C), regenerator that forms the space between the cylinders and the buffer space (under the pistons). Before the start-up and as a result of long-term operation, the average pressure in the working space (above the pistons) and in the buffer space is the same. However, in the initial phase of operation, the average pressure in the...
-
The thermal effort during marine steam turbine flooding with water
PublicationThe work discussed an extreme case of cooling a steam turbine. The ship's steam turbine was used as an example. In marine transport units with low-speed engines dominate, however, there are also units with steam turbines. An example of analysed marine steam turbine is shown in Fig. 1. When considering the issue of cooling steam turbines, it is necessary to estimate the extreme conditions that may occur during operation of the turbine....
-
Alternative cogeneration thermodynamic cycles for domestic ORC
PublicationThe Organic Flash Cycle (OFC) is suggested as a vapor power cycle that could potentially improve the efficiency of utilization of the heat source. Low and medium temperature finite thermal sources are considered in the cycle. Additionally the OFC’s aim is to reduce temperature difference during heat addition. The study examines 2 different fluids. Comparisons are drawn between the OFC and an optimized basic Organic Rankine Cycle...
-
EXPERIMENTAL AND NUMERICAL VALIDATION OF THE IMPROVED VORTEX METHOD APPLIED TO CP745 MARINE PROPELLER MODEL
PublicationThe article presents a numerical analysis of the CP745 marine propeller model by means of the improved vortex method and CFD simulations. Both numerical approaches are validated experimentally by comparing with open water characteristics of the propeller. The introduced modification of the vortex method couples the lifting surface approach for the propeller blades and the boundary element method for the hub. What is more, a...
-
Experimental study of pressure rise at the evaporator of capillary pumped loop with acetone and water as working fluids
PublicationIn this work studied is the possibility of fluid pumping using capillary forces in the capillary pumped loop. Experimental and theoretical studies have been performed to understand the phenomena associated with heat transfer in porous structure of the evaporator. The capillary effect was studied during operation of two different capillary porous structures with two different working fluids, namely water and acetone. The results...
-
Capillary pumped loop as a tool for collecting large heat fluxes from electronic devices on warships
PublicationThe combat potential of future warships will be directly related to the use of modern electronic devices being parts of advanced systems, such as, for instance, radar systems, fire aiming systems, fire detection systems, electric drive systems, and even electronic and radio-electronic weaponry, railguns and lasers, installed on these warships. The capacity and functionality of these devices is continually increasing, at decreasing...
-
Pilot installation for thermal utilization of meat-and-bone meal using the rotary kiln pyrolyzer and the fluidised bed boiler
PublicationThe technology of thermal utilization of meat-and-bone meal (MBM) is still at the research state. However, there are already a number of existing pilot-scale installations that provide the complete, effective and environmentally safe process conducting. The universal technology was developed that allows to combust various types of waste, including animal waste, municipal waste and sludge, mixed at any ratio with different types...
-
Thermal-hydraulic issues of flow boiling and condensation in organic Rankine cycle heat exchangers
PublicationW pracy przedstawiono szereg zagadnień cieplno-przepływowych podczas wrzenia i kondensacji w przepływie w wymiennikach ciepła obiegu ORC. Uwzględniono przemiany fazowe. Analizowano zagadnienia stabilności pracy wymienników oraz ich dynamikę
-
Flow Boiling in Minigap in the Reversed Two-Phase Thermosiphon Loop
PublicationThe paper presents the results of experimental investigations of a model of a heat exchanger featuring a minigap, which is perceived as an evaporator for an inverted thermosiphon. The system works with a single component test fluid. The tested evaporator generates pumping power in the test loop in a way similar to the mammoth pump. The tests regarded a module of the heat exchanger, consisting of a hot leg and a cold leg with the...
-
Analysis of the possibility of determining the general characteristics using the operational data of a vehicle engine
PublicationThe paper presents an analysis of the possibility of determining the general characteristics using the operational data of an engine of refuse collection vehicle. Data acquisition was done by reading information from the CAN network using FMS standard (Fleet Management System), which is widely used in heavy duty vehicles since year 2002. The paper presents the analysis of the expected measurement uncertainties resulting from the...
-
Experimental investigation of forced convection of water/EGAl2O3 nanofluids inside horizontal tube
PublicationIn this paper, forced convection of water/EG-Al2O3 nanofluids inside horizontal stainless steel tube is studied experimentally. As base fluid served water/EG mixture of two ratios (60:50 and 50:50). Nanoparticle mass concentrations was 0.1% or and 1%. Transition and turbulent flow regimes were tested. Average heat transfer coefficient and pressure drop values were determined for nanofluids and compared to base fluids. Deterioration...
-
Thermodynamic modeling of combustion process of the internal combustion engines – an overview
PublicationThe mathematical description of combustion process in the internal combustion engines is a very difficult task, due to the variety of phenomena that occurring in the engine from the moment when the fuel-air mixture ignites up to the moment when intake and exhaust valves beginning open. Modeling of the combustion process plays an important role in the engine simulation, which allows to predict incylinder pressure during the combustion,...
-
Analysis of the possibilities of using of DME fuel in motor boat drive systems
PublicationThe characteristics of alternative fuel for diesel: dimethyl ether (DME) and an analysis of the potential to reduce emissions of toxic compounds by the engines when running on this fuel have been presented in this work. Basic types of design solutions of gas supply and control systems, possible for use in internal combustion engines with DME supply have been also presented. The paper presents a study of the legislation and an analysis...
-
Small Scale Gasification of Biomass and Municipal Wastes for Heat and Electricity Production using HTAG Technology
PublicationCombustion and gasification technology utilizing high-cycle regenerative air/steam preheater has drawn increased attention in many application areas. The process is to be realized at temperature level above ash melting point using highly preheated agent. The use of highly preheated media above 900degC provides additional energy to conversion processes and results in considerable...
-
APPLICATION OF VORTEX FLOW MODEL IN PROPELLER-STATOR SYSTEM DESIGN AND ANALYSIS
PublicationThe paper covers basics of the vortex model used for propeller-stator systems. The outline of the design algorithm is given and the results of its application are shown. The designed propeller-stator system was the subject of model tests run at the CTO model basin and cavitation tunnel. Stator’s influence on the delivered power required by the propeller and its revolution rate has been examined by conducting self-propulsion...
-
Determination of dryout localization using a five-equation model of annular flow for boiling in minichannels
PublicationDetailed studies have suggested that the critical heat flux in the form of dryout in minichannels occurs when the combined effects of entrainment, deposition, and evaporation of the film make the film flow rate go gradually and smoothly to zero. Most approaches so far used the mass balance equation for the liquid film with appropriate formulations for the rate of deposition and entrainment respectively. It must be acknowledged...
-
Advanced Turbine Cycles with Organic Media
PublicationOrganic Rankine Cycle (ORC) power plants have become very popular and have found their applications in systems with renewable sources of energy. So far their overall efficiencies are not very impressive and only for the upper temperature of about 300 °C do they exceed 20%. A drawback of these cycles is the limitation of the cycle upper temperature due to the heat exchanger technology and the materials used. However, it is possible...
-
Experimental investigation on straight and u-bend double tube heat exchanger with active and passive enhancement methods
PublicationAuthors in this work want to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. In the study, Wilson plot approach was applied in order to estimate heat transfer coefficients for all heat exchanger (HX) configurations. The study focuses on experimental values of heat transfer coefficient...
-
Extremal thermal loading of a bifurcation pipe
PublicationThe subject of considerations is a spherical bifurcation pipe of a live steam made of steel P91, which is an element of a block of coal-fired power plant working with a 18K370 turbine. As experience shows, it is a very sensitive element of the boiler pipelines. An extreme work scenario for such a block has been adopted, in which the turbine is shutting down to a warm state three times in 24 hours. This is an action dictated by...
-
A simplified energy dissipation based model of heat transfer for post-dryout flow boiling
Publicationmodel for post dryout mist flow heat transfer is presented based on considerations of energy dissipation in the flow. The model is an extension of authors own model developed earlier for saturated and subcooled flow boiling. In the former version of the model the heat transfer coefficient for the liquid singlephase convection as a reference was used, due to the lack of the appropriate model for heat transfer coefficient for the...
-
Evaluation of the efficiency of the duty cycle of refuse collection vehicle based on real-world data
PublicationIn this paper a method of the efficiency evaluation of the duty cycle of Refuse Collection Vehicle is presented. Using real world data, two representative duty cycles were analysed. Total cycle efficiency was calculated, as well as the efficiency of particular cycle phases. Then, energy needed to collect and compact the waste and energy from fuel were compared. Measured and calculated values were shown on the diagrams illustrating...
-
Numerical simulation of natural convection of Glycol-Al2O3 nanofluids from a horizontal cylinder
PublicationThis paper deals with natural convection around a circular cylinder with constant heat flux in a cavity using computational fluid dynamics. As fluids ethylene glycol and a mixture of ethylene glycol with Al2O3 nanoparticles (mass concentrations of nanoparticles: 0.1% and 1%) are chosen. Rayleigh number ranges from 3104 to 3105. The nanofluids are modeled with single-phase approach. For the investigated range of nanoparticle concentration, the...
-
Evaluati on of long-term start up costs impact on short-term price based operational optimization of a CCGT using MILP
PublicationAn increasing share of the weather-dependent RES generation in the power system leads to the growing importance of flexibility of conventional power plants. They were usually designed for base load operation and it is a challenge to determine the actual long-term cycling costs, which account for an increase in maintenance and overhaul expenditures, increased forced outage rates and shortened life expectancy of the plant and components....
-
Mathematical modeling of hydrogen production performance in thermocatalytic reactor based on the intermetallic phase of Ni3Al
PublicationThe main goal of the following work is to adjust mathematical modelling for mass transfer, to specific conditions resulting from presence of chemical surface reactions in the flow of the mixture consisting of helium and methanol. The thermocatalytic devices used for decomposition of organic compounds incorporate microchannels coupled at the ends and heated to 500 oC at the walls regions. The results of the experiment were compared...
-
Heavy Duty Vehicle Fuel Consumption Modelling Based on Exploitation Data by Using Artificial Neural Networks
PublicationOne of the ways to improve the fuel economy of heavy duty trucks is to operate the combustion engine in its most efficient operating points. To do that, a mathematical model of the engine is required, which shows the relations between engine speed, torque and fuel consumption in transient states. In this paper, easy accessible exploitation data collected via CAN bus of the heavy duty truck were used to obtain a model of a diesel...
-
CAUSALITY IN MODELS OF THERMAL PROCESSES IN SHIP ENGINE ROOMS WITH THE USE OF BOND GRAPH (BG) METHOD
PublicationWith a single approach to modeling elements of different physical nature, the method of Bond Graph (BG) is particularly well suited for modeling energy systems consisting of mechanical, thermal, electrical and hydraulic elements that operate in the power system engine room. The paper refers to the earlier presented new concept of thermal process modeling using the BG method. The authors own suggestions for determining causality...
-
Discrete-continuous optimisation of an axial flow blood pump
PublicationThis paper presents results of discrete-continuous optimisation of an axial flow blood pump. Evolution Strategies (ES) are used as a global optimisation method in order to localise the optimal solution in relatively short time. The whole optimisation process is fully automated. This also applies to geometry modelling. Numerical simulations of the flow inside the pump is performed by means of the Reynolds-Average Navier-Stokes...
-
Thermal and Hydrodynamic Phenomena in the Stagnation Zone — Impact of the Inlet Turbulence Characteristics on the Numerical Analyses
PublicationOne of the methods of heat transfer enhancement is utilization of the turbulent impinging jets, which were recently applied, for example, in the heat exchangers. Their positive impact on the heat transfer performance was proven, but many questions related to the origin of this impact are still unanswered. In general, the wall-jet interaction and the near-wall turbulence are supposed to be its main reason, but their accurate numerical...
-
Experimental Investigations on the Influence of Coil Arrangement on Melting/Solidification Processes
PublicationThe latent heat thermal energy storage units are very popular because of their high energy density and almost close to constant temperature during the charging/discharging. In the present study has been proposed new shell-and-coil geometry with a shifted coil position to enhance the performance of phase change thermal magazine. The experimental investigations have been performed both for the melting and solidification process of...
-
Experimental examination and modification of chip suction system in circular sawing machine
PublicationThe article presents the results of experimental examination of the wood chip suction system in the existing sliding table saw before and after its modifi cation. The studies focused on the extraction hood of the mentioned system. The methodical experimental research of the pressure distribution inside the hood during wood chip removal for the selected rotational speed of saw blades of 3500 and 6000 min-1 with a diameter of 300...
-
Local Nusselt number evaluation in the case of jet impingement
PublicationJet impingement still is one of demanding cases regarding computational fluid dynamics, due to its highly turbulent behaviour, with occurrence of turbulent-laminar transition. Even recently developed methods exhibit some drawbacks – RANS based simulations lack accuracy, LES and DNS based ones require too much computational time. Hybrid methods also exist, but their development and validation is in progress. Nevertheless, CFD application...
-
The Discrete-Continuous, Global Optimisation of an Axial Flow Blood Pump
PublicationThis paper presents the results of the discrete-continuous optimisation of an axial flow blood pump. Differential evolution (DE) is used as a global optimisation method in order to localise the optimal solution in a relatively short time. The whole optimisation process is fully automated. This also applies to geometry modelling. Numerical simulations of the flow inside the pump are performed by means of the Reynolds-Average Navier-Stokes...
-
Experimental study on single phase operation of microjet augmented heat exchanger with enhanced heat transfer surface
PublicationThe article presents experimental investigations on a prototype heat exchanger. Presented research is focused on combined active and passive enhancement techniques of surface modification and microjet impingement. The results were compared to reference plate heat exchanger without microjet impingement. The Wilson plot method was applied to determine the heat transfer coefficients in the single phase operation. The heat exchanger...
-
Thermodynamic analysis of the Compressed Air Energy Storage system coupled with the Underground Thermal Energy Storage
PublicationImprovement of flexibility is one of the key challenges for the transformation of the Polish Power System aiming at a high share of renewable energy in electricity generation. Flexible and dispatchable power plants will contribute to this ongoing transformation process as they compensate for fluctuations in electricity generation from renewable energy sources such as wind and photovoltaics. In this context, CAES storage tanks are...
-
Prediction of flow boiling heat transfer data for R134a, R600a and R290 in minichannels
PublicationIn the paper presented is the analysis of the results of calculations using a model to predict flow boiling of refrigerants such as R134a, R600a and R290. The latter two fluids were not used in development of model semiempirical correction. For that reason the model was verified with present experimental data. The experimental research was conducted for a full range of quality variation and a relatively wide range of mass velocity....
-
Optimal boiling temperature for ORC installation
PublicationW pracy przedstawiono oryinalne kryterium wyznaczania optymalnej temperatury odparowania czynnika w obiegu ORC w postaci równań analitycznych. Pokazano przykład obliczeniowy na bazie R134a, wody i etanolu.
-
Analysis of the regenerative braking process for the urban traffic conditions
PublicationIn a regular drive system, with an internal combustion engine, vehicle braking is connected with the unproductive dissipation of kinetic and potential energy accumulated in the mass of the vehicle into the environment. This energy can constitute up to 70% of the energy used to drive a vehicle under urban conditions. Its recovery and reuse is one of the basic advantages of hybrid and electric vehicles. Modern traffic management...
-
A universal NDT method for examination of low energy impact damage in CFRP with the use of TLC film
PublicationThe article presents an attempt to use a sheet of laminated thermochromic liquid crystal film (TLC film) for non-destructive testing of the impact damage (energy values: 1J, 2J, 3J and 4J) in carbon fibre-reinforced polymer (CFRP). This is a new, alternative NDT approach based on the thermo-optical effect. The main advantages of this method are a) the low cost of TLC film, b) the low cost of recording devices due to the usage of...
-
Pressure drop related to flow maldistribution in a model minichannel plate heat exchanger
PublicationThe paper describes the issues related to the pressure drop that accompanies the phenomenon of maldistribution of working fluid between the channels of a model minichannel plate heat exchanger. The research concerns a single exchanger's plate containing 51 (in every geometry) parallel rectangular minichannels of hydraulic diameters 461 µm, 571 µm, 750 µm and 823 µm. In addition, the more complex geometry has been investigated,...
-
Calculation method for flow boiling and flow condensation of R134a and R1234yf in conventional and small diameter channels
PublicationThe paper presents the results of calculations performed using the authors’ model to predict the heat transfer coefficient during flow boiling for two refrigerants R134a and R1234yf. The experimental data from various past studies have been collected and the calculations have been conducted for the full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house...
-
Neoclassical Navier–Stokes Equations Considering the Gyftopoulos–Beretta Exposition of Thermodynamics
PublicationThe seminal Navier-Stokes equations were stated even before the creation of the foundations of thermodynamics and its first and second laws. There is a widespread opinion in the literature on thermodynamic cycles that the Navier-Stokes equations cannot be taken as a thermodynamically correct model of a local "working fluid", which would be able to describe the conversion of "heating" into "working" (Carnot's type cycles) and vice...
-
A model of liquid film breakdown formed due to impingement of a two-phase jet on a horizontal surface
PublicationThe present work aims to provide an explanation to the phenomenon of breakdown of the thin liquid film created by impinging two-phase, liquid-gas jet. Existing in the literature models describe merely thebreakdown of single phase liquid films. The model presented here is based on examination of mass and energy equations under the applied criterion of the minimum of total energy. That allows to determinethe minimum thickness of...
-
Utilisation of bleed steam heat to increase the upper heat source temperature in low-temperature ORC
PublicationW pracy przedstawiono możliwość dogrzewu obiegu ORC za pomocą pary upustowej.
-
A Model of Thermal Energy Storage According to the Convention of Bond Graphs (BG) and State Equations (SE)
PublicationThe main advantage of the use of the Bond Graphs method and State Equations for modeling energy systems with a complex structure (marine power plants, hybrid vehicles, etc.) is the ability to model the system components of different physical nature using identical theoretical basis. The paper presents a method of modeling thermal energy storage, which is in line with basic BG theory. Critical comments have been put forward concerning...
-
Turbulence models impact on the flow and thermal analyses of jet impingement
PublicationAccurate numerical reconstruction of heat and mass transfer processes in particular applications, such a jet impingement, is difficult to obtain even with the use of modern computational methods. In the proposed paper, the flow and thermal phenomena occurring during single minijet impingement on the flat, concave and convex, heated surfaces were considered. Problem of impingement on non-flat surface, still not common and purely...
-
Deformation and Surface Color Changes of Beech and Oak Wood Lamellas Resulting from the Drying Process
PublicationThe drying process was examined relative to parameters’ influence on the deformation and surface layer color changes of beech wood (Fagus sylvatica L.) and oak wood (Quercus robur L.). The goal was to analyze the impact of drying process conditions, wood and growth rings types, and load on the deformation and surface color changes of drying thin wooden elements. A further aim was to reduce the time of the lamella drying and minimize...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena, however their description with a single correlation has yet to be suggested. In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the bubble generation is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationIn the paper a method developed earlier by the first author is applied to calculations of heat transfer coefficient for inside tube condensation. The method has been verified using experimental data from literature on several fluids in different microchannels and compared to three well established correlations.
-
Numerical Analysis of the Unsteady Propeller Performance in the Ship Wake Modified by Different Wake Improvement Devices
PublicationThe paper presents summary of numerical analysis of the unsteady propeller forces and induced pressure pulses generated by the selected real propeller of 7000 tons product tanker, operating in five different wakefields including four inflenced by the different wake improvement devices. The results of the analysis are partly compared with experimental data and univocal conclusions about the optimum wake improvement device are presented.
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symetrical phenomena. Their description however with a single correlation has yet to be suggested.In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the buble generetion is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such case...
-
Porous structures in aspects of transpirating cooling of oxycombustion chamber walls
PublicationA wet oxycombustion chamber, which must be effectively cooled due to high temperature evolved during the oxy-combustion process, by using the phenomena of Reynolds thermal transpiration and Navier slip velocity. Closures needed to execute mass flow rate in a microchannel, which should be treated as a single porous structure in the walls of the combustion chamber, have been obtained by applying a local 3D approach. The Navier-Stokes...
-
Mitigation of the Flow Maldistribution in Minichannel and Minigap Heat Exchangers by Introducing Threshold in the Manifolds
PublicationIn the present paper, a detailed numerical investigation has been carried out to analyze the flow maldistribution in 50 parallel rectangular cross-section (1 mm depth and 1 mm width) minichannels and minigap section (1 mm depth and 99 mm width) with rectangular/trapezoidal manifolds in Z-type flow configuration. The author carried out numerical investigation with various mass flowrates, namely 0.05 kg/s, 0.1 kg/s and 0.2 kg/s which...
-
Thermal-Hydraulic Studies on the Shell-and-Tube Heat Exchanger with Minijets
PublicationIn this paper a patented design of a heat exchanger with minijets, with a cylindrical construction is presented. It is followed by the results of its systematic experimental investigations in the single-phase convection heat transfer mode. Based on these results, validation of selected correlations (coming from the literature) describing the Nusselt number was carried out. An assessment of the heat exchange intensification level...
-
Thermal and hydraulic phenomena in boundary layer of minijets impingement on curved surfaces
PublicationPresented work considers flow and thermal phenomena occurring during the single minijet impingement on curved surfaces, heated with a constant heat flux, as well as the array of minijets. Numerical analyses, based on the mass, momentum and energy conservation laws, were conducted, regarding single phase and two-phase simulations. Focus was placed on the proper model construction, in which turbulence and boundary layer modeling...
-
Application of Stirling Engine Type Alpha Powered by the Recovery Energy on Vessels
PublicationThe Stirling engine is a device, in which thermal energy is transformed into mechanical without a contact between the heat carrier, and the working gas closed in the engine. Mentioned feature makes this type of engine very attractive for the use of the recovery energy, taken from other heat devices. One of the potential applications of Stirling engines is the use of thermal energy generated in the ship's engine room for producing...
-
Investigations on mixture preparation for two phase adiabatic pressure drop of R134a flowing in 5 mm diameter channel
PublicationThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a. Study cases have been set for a mass flux varying from 200 to 400 kg/m2 s, at the saturation temperature of 19.4 ◦C. Obtained experimental data was compared with the available correlations from the literature for the frictional pressure drop during adiabatic flow. Influence of mixture preparation on pressure drop was investigated, for...
-
Model of heat transfer in the stagnation point of rapidly evaporating microjet
PublicationThe paper presents investigation in the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. It was proved that the phenomenon is similar to that of pool boiling. Results of experiments were compared with predictions by the model showing a good consistency.
-
Model of heat transfer in the stagnation point of rapidly evaporating microjet
PublicationThe paper presents investigation into the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. Experiments were conducted using the nozzle size of 70 and 100 mikrometer respectively. In the course of investigations obtained were experimental relations between heat flux and wall superheating. It was proved that the phenomenon is similar to that of pool boiling...
-
Current Status, Barriers and Development Perspectives for Circular Bioeconomy in Polish South Baltic Area
PublicationThe following article presents the current legal situation in Poland as well as in the European Union. Data on biomass production in the Polish South Baltic area were analyzed, along with an indication of the key sectors for the development of bioeconomy. Presentation of the current state of biomass management was made and areas necessary for development were indicated to facilitate the sustainable management of biomass and waste...
-
Particulate Matter Production of Small Heat Source Depending on the Bark Content in Wood Pellets
PublicationWood pellets as biofuel are more and more used in small heat sources in Europe. Standard wood pellets are produced from wood sawdust without bark. The paper deals about the impact of bark in wood pellets on their properties and combustion process. Special attention in this work is paid to production of particulate matter during combustion of wood pellets depending on bark content. There were experimentally produced spruce wood...
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublicationThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublicationThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...
-
Possibilities of heat transfer augmentation in heat exchangers with minichannels for marine applications
PublicationIn the paper, new trends in development of microchannel heat exchangers are presented. The exchangers developed in this way can be applied in marine applications. Main attention was focused on heat exchangers design with reduced size of passages namely based on microchannels. In our opinion future development of high power heat exchangers will be based on networks micro heat exchangers.
-
A Theoretical and Experimental Study of Moderate Temperature Alfa Type Stirling Engines
PublicationThe Stirling engine is a device that allows conversion of thermal energy into mechanical energy with relatively high efficiency. Existing commercial designs are mainly based on the usage of high temperature heat sources, whose availability from renewable or waste heat sources is significantly lower than that of moderate temperature sources. The paper presents the results of experimental research on a prototype alpha type Stirling...
-
AUGMENTATION OF THE CRITICAL HEAT FLUX IN WATER-Al2O3, WATER-TiO2 AND WATER-Cu NANOFLUIDS
PublicationThe main aim of the proposed study is therefore recognition of the phenomena accompanying nucleate boiling crisis of selected nanofluids during boiling on horizontal tubes of various outside diameters. Of particular interest is impact of contact angle and tube diameter on the value of critical heat flux. The results obtained should give more light on the nature of nucleate boiling crisis and will serve as a basis for future theoretical...