prof. dr hab. inż. Kazimierz Darowicki
Publikacje
Filtry
wszystkich: 435
Katalog Publikacji
Rok 2016
-
Opracowanie systemu monitorowania korozji instalacji podstawowej Alkilacji HF w celu bieżącej oceny zagrożenia korozyjnego instalacji
PublikacjaWykonano analizę stanu zagrożenia korozyjnego instalacji alkilacji HF w PKN Orlen S.A. Wytypowano miejsca które powinny zostać objęte systemem monitorowania korozji. Zaprojektowano śluzę korozyjną. Dokonano oceny merytorycznej oraz finansowej różnych rozwiązań systemów monitorowania korozji
-
Performance of zinc-rich coatings evaluated using AFM-based electrical properties imaging
PublikacjaThe paper presents the results of investigation of polyvinyl zinc-rich coating exposed to 97% relativehumidity atmosphere for 40 days. Condition of the coating and evolution of its protective properties weredetermined with the novel AFM-based approach capable of providing surface profiles, local dc currentmaps as well as local impedance spectra. The proposed technique allowed insight into the local changesof coating topography...
-
Research on causes of corrosion in the municipal water supply system
PublikacjaThis paper presents results of failure analysis study to characterize the corrosion damage that occurred in the water supply system in Krakow. This analysis includes: electrochemical noise, linear polarization and resistometric measurements. Water aggressiveness of four water intakes was defined using Langelier and Ryznar indices. Results from this indices did not reveal the causes of considerable corrosion losses in water systems....
-
Restoration and preservation of the reinforced concrete poles of fence at the former Auschwitz concentration and extermination camp
PublikacjaThe objective of this study was to assess the present state of the reinforced concrete poles of fence at the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp. The poles were subjected to renovation about 10 years ago. After this time some deficiencies of applied renovation method were noticed. Cracks appeared between fresh and original part of concrete cover. Analysis of the reasons of these failures...
-
Restoration and preservation of the reinforced concrete poles of fence at the former Auschwitz concentration and extermination camp
PublikacjaThe objective of this study was to assess the present state of the reinforced concrete poles of fence at the former Auschwitz I and Auschwitz II-Birkenau concentration and extermination camp. The poles were subjected to renovation about 10 years ago. After this time some deficiencies of applied renovation method were noticed. Cracks appeared between fresh and original part of concrete cover. Analysis of the reasons of these failures...
-
Study on surface termination of boron-doped diamond electrodes under anodic polarization in H2SO4 by means of dynamic impedance technique
PublikacjaAnodic oxidation is a popular way to modify termination bonds at boron doped diamond electrodes altering their electrochemical and physicochemical properties. Our studies, performed with dynamic electrochemical impedance spectroscopy technique, supported with X-ray photoelectron spectroscopy and ellipsometry analysis prove its utility in continuous on-line monitoring of impedance changes on the electrode surface under polarization...
-
System pomiaru szybkości korozji metodą polaryzacji liniowej w zbiorniku zatłaczającym wodę złożową oraz systemu wody morskiej na platformie wydobywczej Baltic Beta
PublikacjaWykonano analizę sprawności systemu monitorowania szybkości korozji na Platformie wydobywczej Baltic Beta. Dokonano niezbędnych czynności, które umożliwiły ponowne uruchomienie systemu. Przedstawiono rejestry szybkości korozji w okresie od 01.01.2015 do 24.11.2016
-
Wyjaśnienie przyczyn pocienienia rur w piecu technologicznym PC-1 na instalacji DRW II
PublikacjaWykonano analizę przyczyn korozji rur pieca instalacji DRW w oparciu o badania wizualne, SEM, EDX oraz literaturowe. W ciągu 5 lat eksploatacji nastąpiły znaczne ubytki korozyjne rur w wyniku procesów korozyjnych. Z uwagi na zbyt wysoką temperaturę rurek pieca nastąpił proces wysokotemperaturowego pylenia metalu.
Rok 2015
-
Application of multisine nanoscale impedance microscopy to heterogeneous alloy surface investigations
PublikacjaIn the recent years atomic force microscopy is recognized as valuable tool for investigation of surficial features of construction materials. It concerns, among other things, studies of changes caused by such phenomena as galvanic corrosion, passivation associated with the growth of oxide layers, or sensitization of austenitic steels with the formation of carbide phases. In addition, atomic forcemicroscopy allows easy coupling...
-
Assessment of protective properties of rubber lining in absorbers of flue gas desulphurization systems.
PublikacjaResults of research on degradation of rubber lining which is the main protection of absorbers in flue gas desulphurization (FGD) systems were presented. The power plant where the system operated is lignite-fired. Owing to measurements using electrochemical impedance spectroscopy and gravimetric determination of water content in the lining, the areas of the system which are most exposed to degradation were shown. The results obtained...
-
Electrical and mechanical characterization of two-phase alloys by means of scanning probe microscopy in dynamic impedance spectroscopy mode
PublikacjaDynamic impedance spectroscopy, evaluated for measuring non-stationary systems, was used in combination with scanning probe microscope. Using this approach, localized impedance measurements in the AFM contact mode could be carried out. Additionally, impedance–force curves were made at each phase of investigated materials to illustrate the relation between impedance and the force applied to a probe. Therefore, correlation of electrical...
-
Evidence for solid state electrochemical degradation within a small molecule OLED
PublikacjaAcridone derivative have been synthesised and used as OLED (Organic Light Emitting Diode) emitters which were found to be electroactive. Electrochemical investigations showed a side reaction takes place inside an active layer which diminished the overall device efficiency. By using a dopant and host active layer architecture, the formation of the by product was removed. The by-product was identified as a σ-dimer formed inside an...
-
Formation of Highly Conductive Boron-Doped Diamond on TiO2 Nanotubes Composite for Supercapacitor or Energy Storage Devices
PublikacjaIn the present paper, we report the phenomena of the formation of the novel composite nanostructures based on TiO2 nanotubes (NTs) over-grown by thin boron-doped diamond (BDD) film produced in Microwave Plasma Enhanced Chemical Vapor Deposition (PE MWCVD). The TiO2 nanotube array overgrown by boron-doped diamond immersed in 0.1 M NaNO3 can deliver high specific capacitance of 7.46 mF cm−2. The composite electrodes were characterized...
-
Impedance monitoring of fuel cell stacks
Publikacja -
Impedance monitoring of fuel cell stacks
PublikacjaThis paper presents an innovative, electrochemical impedance method for monitoring of electrochemical behaviour of a multi-cell, direct methanol fuel cell (DMFC) device. This method not only provides classical voltage changes at successive cells but also allows their detailed impedance behaviour to be presented. Impedance characteristics of individual cells within a fuel cell stack (depending on actual operating conditions) are...
-
Improved surface coverage of an optical fibre with nanocrystalline diamond by the application of dip-coating seeding
PublikacjaGrowth processes of diamond thin films on the fused silica optical fibres (10 cm in length) were investigated at various temperatures. Fused silica pre-treatment by dip-coating in a dispersion consisting of detonation nanodiamond (DND) in dimethyl sulfoxide (DMSO) with polyvinyl alcohol (PVA) was applied. Nanocrystalline diamond (NCD) films were deposited on the fibres using the microwave plasma assisted chemical vapour deposition...
-
Instantaneous impedance monitoring of AA 7075 aluminum alloy corrosion in borate buffer with admixed chloride ions
PublikacjaThe study presents a research capabilities of Dynamic Electrochemical Impedance Spectroscopy (DEIS) as a tool used for instantaneous on-line monitoring of corrosion processes on the example of AA 7075 aluminum alloy. A borate buffer with admixed chloride ions in a quantity ranging from 0.05 to 25 mM was used to represent different types of corrosion attack. The surface of samples specimens was evaluated before and after the tests...
-
Method of sacrificial anode dual transistor-driving in stray current field
PublikacjaIn order to control a magnesium anode in a stray current interference field, a dual transistor driving system has been proposed. It consisted of a combination of PNP and NPN transistors. Dual transistor driven system and direct anode to cathode connection were electrochemically tested in 3% NaCl solution. The dual transistor driven system increased the anode efficiency and reduced hydrogen evolution and the risk of embrittlement....
-
Ocena techniczna określająca stan i efektywność zabezpieczenia antykorozyjnego w postaci ochrony katodowej obiektów PPPP „NAFTOPORT” sp. z o.o.
PublikacjaDokonano oceny skuteczności ochrony katodowej realizowanej za pomocą anod galwanicznych w Bazie Przeładunku Paliw Płynnych w Porcie Północnym w Gdańsku na następujących obiektach: zapory przeciwrozlewowe, stanowiska przeładunkowe, estakady rurociągów, pomosty, dalby cumownicze i odbojowe, monitory p.poż. Oceny dokonano na podstawie wykonanych pomiarów potencjału polaryzowanych katodowo obiektów.
-
Protection of bridges against stray current corrosion
PublikacjaA case study of Siennicki Bridge stray current corrosion hazard is presented. A corrosion risk was caused by incorrectly designed tram line traction which goes over the bridge. No dielectric insulation between running rails and bridge steel construction was used. A variety of protection methods against stray currents are described. Characteristics of the endangered bridge were described. Impressed current cathodic protection system...
-
The protection and monitoring of a distribution piping network for potable water supply
PublikacjaPurpose – The purpose of this paper is to implement the corrosion protection method for steel pipes used in a municipal water-pipe network. Results of an inhibitor protection system installed on the system are presented. Inhibitor protection was required due to the high corrosivity of the water collected by a surface intake, which had resulted in a large number of failures and low water quality, due to the presence of corrosion...
-
Weryfikacja dokumentacji technicznej systemu ochrony katodowej rurociągu paliwowego
PublikacjaZweryfikowano dokumentację techniczną systemu ochrony katodowej rurociągu paliwowego
Rok 2014
-
Analiza działania substancji chemicznej na elementy sprzętu elektronicznego
PublikacjaW pracy dokonano analizy działania czynnika chłodniczego oraz środka gaśniczego, a także współoddziaływania obydwu powyższych na korozyjność elementów elektronicznych
-
Analiza weryfikująca poprawność istniejącego układu ochrony przed korozją i osadami instalacji DRW4 w kontekście obecnych warunków pracy instalacji
PublikacjaCelem pracy były pomiary korozyjności kondensatów pochodzących z kolumny destylacyjnej z dodatkiem neutralizatora oraz inhibitora korozji, ponadto przeprowadzono badania SEM i EDX produktów korozji pochodzących z rurek chłodnicy powietrznej. Wykazano, że znacznie większą agresywnością charakteryzują się kondensaty które pochodzą z przerobu ropy naftowej zawierającą slopy.
-
Application of dynamic impedance spectroscopy to scanning probe microscopy.
PublikacjaDynamic impedance spectroscopy, designed for measuring nonstationary systems, was used in combination with scanning probe microscopy. Using this approach, impedance mapping could be carried-out simultaneously with topography scanning. Therefore, correlation of electrical properties with particular phases of an examined sample was possible. The sample used in this study was spheroidal graphite cast iron with clearly defined phases...
-
Application of Dynamic Impedance Spectroscopy to Scanning Probe Microscopy
Publikacja -
Determination of causes of accelerated local corrosion of austenitic steels in water supply systems
PublikacjaThis paper concerns an inspection of a water supply system, made of AISI 304 steel, which showed signs of local corrosion at the weld. Such corrosion caused material perforation after very short periods of operation. It was revealed that steel was sensitised during the welding process. It was also proven that chromium micro-segregation occurred in the alloy leading to galvanic cell formation which initialised the process of pitting...
-
Determination of pseudocapacitance chan ges of nickel oxide NiO electrode with use of dynamic electrochemical impedancje spectroscopy
PublikacjaThe electrochemical capacitors (ECs) are attractive energy storage devices which can be applied in many electronic products (e.g., cameras, laptops, cell phones) or hybrid electric vehicles (HEV). The energy storage in ECs is based on capacitive (the electrical double layer charging/discharging) and pseudocapacitive (additional charge provided by faradic reaction) phenomena. Considering the electrodes exhibiting pseudocapacitance,...
-
Dynamic Electrochemical Impedance Spectroscopy (DEIS) as a Tool for Analyzing Surface Oxidation Processes on Boron-Doped Diamond Electrodes
Publikacja -
Dynamic Electrochemical Impedance Spectroscopy (DEIS) as a Tool for Analyzing Surface Oxidation Processes on Boron-Doped Diamond Electrodes
PublikacjaSurface oxidation processes play a key role in understanding electrochemical properties of boron-doped diamond (BDD) electrodes. The type of surface termination groups, which create the potential window of electrolytic water stability or hydrophobicity, influences such properties. In this study the kinetics of oxidation process under anodic polarization were studied in situ by means of Dynamic Electrochemical Impedance Spectroscopy...
-
Dynamic Nanoimpedance Characterization of the Atomic Force Microscope Tip-Surface Contact
PublikacjaNanoimpedance measurements, using the dynamic impedance spectroscopy technique, were carried out during loading and unloading force of a probe on three kinds of materials of different resistivity. These materials were: gold, boron-doped diamond, and AISI 304 stainless steel. Changes of impedance spectra versus applied force were registered and differences in the tip-to-sample contact character on each material were revealed. To...
-
Effect of native air-formed oxidation on the corrosion behavior of AA 7075 aluminum alloys
Publikacja -
Effect of native air-formed oxidation on the corrosion behavior of AA7075 aluminum alloys
PublikacjaThe microstructure of aluminum alloys plays a key role in their corrosion resistance. In particular, the presence of intermetallic precipitates differing in the potential from the alloy matrix induces local corrosion. The study presents the effect of native air-formed oxidation on the corrosion behavior of AA 7075 aluminum alloy. Various microscopic and spectroscopic techniques were used to examine the changes occurring in the...
-
Ekspertyza oddziaływania napowietrznych linii wysokiego napięcia
PublikacjaWykonano obliczeń oddziaływania linii 400kV i 110kV na gazociągi DN500, DN400 i DN100 w miejscach ich kolizji oraz wyznaczono gęstości upływających prądów przez jednostkowy defekt o powierzchni 1cm^2.
-
EVALUATION OF CAUSES OF CORROSION OF PLATE HEATEXCHANGER
PublikacjaPrzeprowadzono analizę zniszczeń korozyjnych wykrytych na płycie wymiennika ciepła stosowanego do chłodzenia silnika głównego statku. Stwierdzono obecność wżerów korozyjnych oraz korozji szczelinowej. Przedstawiono możliwe przyczyny wystąpienia w.w. uszkodzeń.
-
Implementation and Validation of Multisinusoidal, Fast Impedance Measurements in Atomic Force Microscope Contact Mode
Publikacja -
Implementation and Validation of Multisinusoidal, Fast Impedance Measurements in Atomic Force Microscope Contact Mode.
PublikacjaThis study presents a novel approach to impedance measurements. The methodology discussed is limited to contact in the sample-probe system under ambient conditions without the presence of electrolyte. Comparison with results of direct and alternating current measurements for well-defined metallic surfaces are made. In spite of idealization related to the type of contact examined, the proposed technique provides an improvement of...
-
Influence of water salinity on corrosion risk - the case of the southern Baltic Sea coast.
PublikacjaWater corrosivity in Gdansk Bay, Poland, the southern part of the Baltic Sea, was investigated. The analysed region is heavily industrialized, and the coastline is very diverse. Twenty-seven test points along the coastline were selected. Water parameters such as salinity, total dissolved solids content, resistivity, conductivity, oxygenation, pH and corrosion rate were determined. The results of the investigation are presented....
-
Local impedance imaging of boron-doped polycrystalline diamond thin films
Publikacja -
Local impedance imaging of boron-doped polycrystalline diamond thin films
PublikacjaLocal impedance imaging (LII) was used to visualise surficial deviations of AC impedances in polycrystalline boron-doped diamond (BDD). The BDD thin film electrodes were deposited onto the highly doped silicon substrates via microwave plasma-enhanced CVD. The studied boron dopant concentrations, controlled by the [B]/[C] ratio in plasma, ranged from 1 × 1016 to 2 × 1021 atoms cm−3. The BDD films displayed microcrystalline structure,...
-
Local properties of organic coatings close to glass transition temperature
PublikacjaAcrylic coating applied on copper substrate has been investigated at different temperatures starting from the ambient one up to the level above the glass transition temperature. Its local topographic and electric properties have been examined with the atomic force microscopy (AFM) based approach including dc current mapping and local impedance spectroscopy. The local findings have been compared with the information from global...
-
Method of sacrificial anode transistor-driving in cathodic protection system
PublikacjaA magnesium anode driving system has been proposed. A PNP driving transistor has been used. Electrochemical testing in 3%NaCl, results and comparison of the driving system and classic direct anode to cathode connection are presented. The driving system reduced the protection current and stabilized the working conditions of the anode. Higher anode efficiency was achieved. Overprotection and hydrogen embrittlement threats were prevented...
-
Multivariate analysis of impedance data obtained for coating systems of varying thickness applied on steel
PublikacjaElectrochemical impedance spectroscopy (EIS) has proven to be a valuable test method for the electrochemical characterization of protective coatings on metals. The common way of analysis in impedance spectroscopy is to model the impedance spectrum by means of an equivalent circuit and to extract the quantity of interest using optimization techniques. A model, corresponding to the behavior of the sample under testing, is important...
-
Pomiary skuteczności ochrony katodowej stanowiska przeładunkowego T1 w Bazie Przeładunku Paliw Płynnych w Porcie Północnym w Gdańsku.
PublikacjaWykonano pomiary potencjału oraz określono skuteczność działania ochrony katodowej stalowych konstrukcji podwodnych na nowo wybudowanym stanowisku przeładunkowym T1 przy falochronie wewnętrznym północnym w Bazie Przeładunku Paliw Płynnych w Porcie Północnym w Gdańsku.
-
Simultaneous impedance and volumetric studies and additionally potentiodynamic polarization measurements of molasses as a carbon steel corrosion inhibitor in 1M hydrochloric acid solution
PublikacjaThe inhibition effect of molasses on the corrosion of low carbon steel in 1M hydrochloric acid solution was investigated by volumetric and electrochemical measurements. Potentiodynamic polarization and dynamic electrochemical impedance spectroscopy (DEIS) results were obtained and compared with to those, obtained with the hydrogen evolution technique. All results indicate that molasses functioned as a good inhibitor in 1M hydrochloric...
-
WYKONANIE BADAŃ I POMIARÓW POWŁOK ANTYKOROZYJNYCH ZABEZPIECZAJĄCYCH ELEMENTY METALOWE KONSTRUKCJI STALOWYCH, APARATÓW I URZĄDZEŃ INSTALACJI ODZYSKU OPARÓW BENZYN W BAZIE PALIW GRUPY LOTOS S.A. w POZNANIU
PublikacjaPrzeprowadzono inspekcję powłok malarskich na konstrukcji odzysku oparów w bazie Paliw Płynnych Grupy Lotos. Na podstawie wyników inspekcji przedstawiono wnioski i zalecenia związane ze stanem powłok i ich ewentualną naprawą.
-
Zbadanie środowiska korozyjnego oraz jego wpływu na rozkład, wielkość i głębokość wżerów korozyjnych rur.
PublikacjaPrzedstawiono wyniki oceny wizualnej rurociągów składowanych w okolicy Warszawy. Stwierdzono występowanie korozji galwanicznej w wyniku tworzenia się ogniw zmiennego napowietrzenia. Obserwacje poparto badaniami laboratoryjnymi.
Rok 2013
-
A measurement system for nonlinear surface spectroscopy with an atomic force microscope during corrosion process monitoring
PublikacjaIn addition to traditional imaging the surface, atomic force microscopy (AFM) enables wide variety of additional measurements. One of them is higher harmonic imaging. In tapping mode the nonlinear contact between tip and specimen results in higher frequency vibrations. More information available from the higher harmonics analysis proves to be helpful for more detailed imaging. Such visualization is espe-cially useful for heterogeneous...
-
Amperometric sensing of chemical oxygen demand at glassy carbon and silicon electrodes modified with boron-doped diamond
Publikacja -
Amperometric sensing of chemical oxygen demand at glassy carbon and silicon electrodes modified with boron-doped diamond
Publikacja.A boron-doped diamond (BDD) sensor is proposed for effective detection of chemical oxygen demand (COD) by means of amperometric technique. Boron-doped diamond thin films, acting as active sensors, were deposited on both silicon wafer and glassy carbon (GC) substrates by microwave plasma assisted chemical vapour deposition. SEM micrographs showed that BDD–Si displays triangle-faceted crystallites ca. 0.5–3 μm in size, while BDD–GC...
-
ANALIZA STANU TECHNICZNEGO RUROCIĄGÓW: WODY PRZeMYSŁOWEJ I SOLANKI
PublikacjaPracę wykonano na zlecenie Przedsiębiorstwa Badawczo-Wdrożeniowego "HYDRO-POMP" Sp. z o.o. ul. Wróblewskiego 19, 93-578 Łódź. Wykonawcą zlecenia jest Politechnika Gdańska, Wydział Chemiczny, Katedra Elektrochemii, Korozji i Inżynierii Materiałowej, 80-233 Gdańsk, ul. G. Narutowicza 11/12. Celem pracy była analiza stanu technicznego i badania dwóch rurociągów: solanki oraz wody przemysłowej. Badania wykonywano w warunkach terenowych...
-
Application of electrochemical impedance spectroscopy to monitoring discharging process of nickel/metal hydride battery
Publikacja -
Application of electrochemical impedance spectroscopy to monitoring discharging process of nickel/metal hydride battery.
PublikacjaThis paper presents the possibility of applying impedance analysis to cell diagnostics. In order to obtain characteristic curves of both electrodes of a NiMH battery simultaneously, a reference electrode was added into the circuit. The authors analysed the cell under three cases, i.e. when its properties are determined only by the state of the positive electrode, only by the state of the negative electrode, or when both electrodes...
-
Application of impedance imaging to evaluation of organic coating degradation at a local scale
Publikacja -
BADANIA SKŁADU ORAZ OCENY DOBORU STALI I KOROZJI KANAŁU WENTYLACYJNEGO NA PŁYWALNI AQUA CENTRUM W KOŚCIERZYNIE
PublikacjaW ramach zlecenia dokonano badania oraz oceny składu doboru stali i korozji kanału wentylacyjnego na pływalni Aqua Centrum w Kościerzynie.
-
Badanie przyczyn korozji skraplaczy aluminiowych.
PublikacjaPrzeprowadzono badania aluminiowych skraplaczy pracujących w układach chłodzenia tramwajów. Stwierdzono, że problemy z korozją są wynikiem stosowania środków myjących o właściwościach korozyjnych w stosunku do zastosowanego aluminium.
-
Badanie przyczyn korozji zbiorników magazynowych na paliwa na terenie stacji benzynowej grupy Lotos w Pruszkowie
PublikacjaPrzedstawiono wyniki oględzin zbiornika na olej napędowy eksploatowany na stacji benzynowej w Pruszkowie. Przedstawiono możliwe przyczyny powstania zniszczeń korozyjnych w dolnej części zbiornika.
-
BADANIE REAKTYWNOŚCI CZYNNIKA ORGANICZNEGO W STOSUNKU DO WYBRANYCH STOPÓW
PublikacjaPrzeprowadzono badanie odporności korozyjnej stali konstrukcyjnej zwykłej jakosci, stali ferrytycznej oraz stopu łozyskowego i próbek uszczelnienia gumowego na działanie oleju silikonowego o sciśle zdefiniowanych właściwościach fizyko-chemicznych. Stwierdzono praktycznie brak znaczących ubytków korozyjnych przekazanych do badań materiałów.
-
Ekspertyza dotycząca potrzeby zastosowania ochrony katodowej zbiorników podziemnych na terenie Bazy Paliw w Poznaniu
PublikacjaWykonano badania terenowe i laboratoryjne w celu określenia potrzeby zastosowania ochrony katodowej projektowanych zbiorników podziemnych na terenie Bazy Paliw w Poznaniu.
-
Electrical mapping of AISI 304 stainless steel subjected to intergranular corrosion performed by means of AFM-LIS in the contact mode
PublikacjaThe paper presents results of the AFM-based approach to local impedance spectroscopy (LIS) measurements performed in a 20 20 lm grid within an austenite grain–grain boundary region for sensitized AISI 304 stainless steel (SS). Maps of electrical parameters obtained on the basis of localized impedance spectra were demonstrated, presenting their changes and correlation with the sample topography. Performed research revealed significant...
-
EVALUATION OF CAUSES OF CORROSION OF HEATING PIPES AND BALLAST CHAMBERS ON HLVJ INNOVATION
Publikacja..
-
Impedance of cation-coupled electron transfer reaction: Theoretical description of one pathway process
PublikacjaIt has been assumed that cation electron coupled charge transfer can be conducted in accordance with two mutually coupled reactions. Using a differential method an expression was introduced which describes the impedance of a cation electron coupled transfer reaction. Also, an electrical equivalent circuit has been defined. The total faradaic impedance is the sum of electron transfer impedance and cation transfer impedance. Issues...
-
Influence of the boron doping level on the electrochemical oxidation of the azo dyes at Si/BDD thin film electrodes
PublikacjaIn this study the efficiency of electrochemical oxidation of aromatic pollutants, such as reactive dyes, at boron-doped diamond on silicon (Si/BDD) electrodes was investigated. The level of [B]/[C] ratio which is effective for the degradation and mineralization of selected aromatic pollutants, and the impact of [B]/[C] ratio on the crystalline structure, layer conductivity and relative sp3/sp2 coefficient of a BDD electrode were...
-
Local impedance spectra of organic coatings
Publikacja -
Measurement system for nonlinear surface spectroscopy by atomic force microscopy for corrosion processes monitoring
PublikacjaIn addition to traditional imaging the surface, atomic force microscopy (AFM) enables wide variety of additional measurements. One of them is higher harmonic imaging. In tapping mode the nonlinear contact between tip and specimen results in higher frequency vibrations. More information available from the higher harmonics analysis proves to be helpful for more detailed imaging. Such visualization is especially useful for heterogeneous...
-
Multi-sensor monitoring of the corrosion rate and the assessment of the efficiency of a corrosion inhibitor in utility water installations
Publikacja -
Multi-sensor monitoring of the corrosion rate and the assessment of the efficiency of a corrosion inhibitor in utility water installations
PublikacjaThis paper presents an implementation of the monitoring of the corrosion rate and the assessment of the efficiency of a corrosion inhibitor in a utility water installation using an automated corrosion monitoring system. Due to the fact that the corrosion inhibitor was added to water intended for human consumption, it was necessary to build a multi-sensor monitoring system. In order to implement corrosion monitoring using a linear...
-
Ocena właściwości ochronnych preparatu Tectyl 477D oraz preparatu SteelRed
Publikacja..
-
Opinia dotycząca zagrożenia korozyjnego zbiorników wody ciepłej na terenie warzelni browaru w Białymstoku
PublikacjaStwierdzono występowanie pęknięć w zbiorniku wody ciepłej procesowej w browarze w Białymstoku. Propagacja pęknięć ma miejsce w obrębie spawu. Wykonano niezbędne badania, oraz zaproponowano metodę ochrony zbiornika przed dalszym rozwojem korozji naprężeniowej.
-
Wykonanie badań wymalowań (w szczególności badań przyczepności) na konstrukcji w Narvie (Estonia) i wyjaśnienie przyczyn obserwowanych uszkodzeń
PublikacjaDokonano oglądu wizualnego i wykonano badania normowe na wymalowaniach na obiekcie budowanej elektrowni w Narvie (Estonia). Pobrano również próbki farb stosowanych do wymalowań oraz fragment elementu konstrukcji do badań.
Rok 2012
-
A complete impedance analysis of electrochemical cells used as energy sources
PublikacjaA comprehensive description of impedance ofelectrochemical systems has been presented, along withthe assumptions of the method used. In this method, amultisinusoidal current excitation signal is used. Thechanges of potential of both the electrodes and thepotential difference between these electrodes are allregistered simultaneously as a function of time. Theproposed method offers the possibility of separatelydetermining the instantaneous...
-
Aplication of impedance imaging to evaluation of organic coating degradation at a local scale
PublikacjaZaproponowano nowe podejście do oceny lokalnych właściwości elektrycznych powłok organicznych. Wykorzystuje ono mikroskop sił atomowych pracujący w trybie kontaktowym. Pomiędzy igłę mikroskopu i podłoże metalowe pokryte powłoką przykładany jest sinusoidalny napięciowy sygnał pobudzenia o zadanej częstotliwości i mierzony jest prądowy sygnał odpowiedzi. Zalety tego podejścia zostały zaprezentowane na przykładzie powłoki akrylowej...
-
Cyclic analysis of thermal impedance of a passive layer of aluminium in a neutral borate buffer solution
PublikacjaW pracy przedstawiono wyniki badań warstwy pasywnej tworzącej się na stopie 1050 A w warunkach zmieniającej się temperatury. Zmiany realizowano w sposób cykliczny zwiększając a następnie zmniejszając temperaturę. W czasie zmian temperatury prowadzono badania metodę dynamicznej elektrochemicznej spektroskopii impedancyjnej. Stwierdzono największe zmiany parametrów elektrycznego schematu zastępczego w czasie pierwszego cyklu zmian....
-
Determination of chemical oxygen demand (cod) at boron-doped diamond (bdd) sensor by means of amperometric technique
PublikacjaA boron-doped diamond (BDD) sensor was proposed for effective detection of chemical oxygen demand (COD) by means of amperometric technique. Thin boron doped diamond active sensor layer was deposited on Si wafer and glassy carbon substrate by Microwave Plasma Enhanced Chemical Vapor Deposition (MW PE CVD). The structure of BDD was confirmed by Raman spectra analysis. Broad Raman bands centered at 482 cm-1 and 1219 cm-1 are typical...
-
Determination of Chemical Oxygen Demand (COD) at Boron-doped Diamond (BDD) Sensor by Means of Amperometric Technique
Publikacja -
Determination of Chemical Oxygen Demand (COD) at Boron-doped Diamond (BDD) Sensor by Means of Amperometric Technique
PublikacjaA boron-doped diamond (BDD) sensor was proposed for effective detection of chemical oxygen demand (COD) by means of amperometric technique. Thin boron doped diamond active sensor layer was deposited on Si wafer and glassy carbon substrate by Microwave Plasma Enhanced Chemical Vapor Deposition (MW PE CVD). The structure of BDD was confirmed by Raman spectra analysis. Broad Raman bands centered at 482 cm-1 and 1219 cm-1 are typical...
-
Diagnostyka stalowej dystrybucyjnej sieci gazowej pod kątem zagrożenia prądami błądzącymi
PublikacjaOmówiono badania zagrożenia gazociągów korozją elektrolityczną, które wykonano na sieci gazowej eksploatowanej przez MSG sp. z o.o. Badaniami objęto wytypowane obszary sieci w rejonach oddziaływania trakcji kolejowej i tramwajowej we wszystkich OZG wchodzących w skład Spółki. W referacie opisano metodykę badań, realizację kolejnych etapów przedsięwzięcia oraz osiągnięte rezultaty. Pomiary terenowe wykonane zostały przez zespoły...
-
Impedance of cation-coupled electron transfer reaction: teoretical description of one pathway process
PublikacjaPrzyjęto możliwość występowanie dwóch wzajemnie sprzężonych reakcji. Opisana została impedancja sprzężonej reakcji przeniesienia elektronu z kationem. Wyznaczony został również model elektrycznego schematu zastępczego. Całkowita impedancja Faradayowska jest sumą impedancji przeniesienia elektronu i impedancji przeniesienia kationu. Przykłady pomiaru impedancyjnego w warunkach potencjostatycznych i potencjodynamicznych zostały omówione....
-
Improving AFM images with harmonic interference by spectral analysis
PublikacjaPrzedstawiono sposób usunięcia zakłóceń pojawiających się na obrazach uzyskiwanych z mikroskopu sił atomowych (AFM). Przybliżono kilka metod stosowanych do redukcji zakłóceń w obrazach. Następnie opisano zidentyfikowane zakłócenia harmoniczne oraz zaproponowany sposób ich znaczącej redukcji. W pracy zamieszczono szereg obrazów uzyskanych z mikroskopu AFM ilustrujących efekty powodowane zakłóceniami oraz skuteczność zaproponowanej...
-
Inspection of protective linings using microwave spectroscopy combined with chemometric methods
PublikacjaOpisano nowa niedestrukcyjna metodę kontroli jakości nowych wykładzin ochronnych na podłożu metalowym oraz oceny ich stanu w trakcie eksploatacji przy zastosowaniu spektroskopii mikrofalowej w szerokim zakresie częstotliwości od 6,5 do 13 GHz. Uzyskane dane pomiarowe dodane zostały obróbce chemometrycznej w celu redukcji ilości danych doświadczalnych i wizualizacji rezultatów. Przedstawiono podstawy teoretyczne metody oraz wyniki...
-
Local impedance spectra of organic coatings
PublikacjaPublikacja przedstawia nowe podejście do lokalnych spektroskopowych pomiarów impedancyjnych powłok organicznych, oparte o mikroskop sił atomowych pracujący w trybie kontaktowym. Pomiędzy nieporuszającą się igłę mikroskopu i podłoże metalowe pokryte powłoką epoksydową przyłożono serię sinusoidalnych napięciowych sygnałów pobudzenia w zadanym zakresie częstotliwości. W ten sposób zarejestrowano lokalne widma w trybie "frequency by...
-
Metody badania interferencji wywoływanych przez prądy błądzące na przykładzie pomiarów wykonanych na terenie Mazowieckiej Spółki Gazownictwa sp. z o.o.
PublikacjaOmówiono stosowane w praktyce metody badania interferencji wywoływanych przez prądy błądzące na rurociągach podziemnych. Zaprezentowano przykładowe wyniki pomiarów wraz z analizą zagrożenia korozją elektrolityczną, które wykonano podczas diagnostyki stalowej dystrybucyjnej sieci gazowej eksploatowanej przez Mazowiecką Spółkę Gazownictwa sp. z o.o.
-
Study of Direct Methanol Fuel Cell Process Dynamics Using Dynamic Electrochemical Impedance Spectroscopy
PublikacjaA new technique, which was developed to characterize the direct methanol fuel cell under work conditions, has been presented in this paper. The impedance measurements were made using dynamic electrochemical impedance spectroscopy research technique in the galvanostatic mode, using multiple sinusoidal excitation. Obtained results show, that together with an increase of the temperature and working load, the global impedance...
Rok 2011
-
Atomic force microscopy based approach to local impedance measurements of grain interiors and grain boundaries of sensitized AISI 304 stainless steel
Publikacja -
Atomic force microscopy based approach to local impedance measurements of grain interiors and grain boundaries of sensitized AISI 304 stanless steel
PublikacjaPraca prezentuje wyniki badań uzyskane z pomiarów techniką lokalnej spektroskopii impedancyjnej (LIS) wykonanych w trybie kontaktowym mikroskopii sił atomowych (AFM), które zostały przeprowadzone w lokalnych obszarach powierzchni ziarna austenitu i na granicy ziarna austenitu wysokostopowej stali austenitycznej AISI 304 poddanej procesowi uczulania oraz na próbkach odniesienia nie poddanych obróbce cieplnej.Badania LIS-AFM były...
-
Badania procesu trawienia stali wysokostopowej za pomocą spektroskopii impedancyjnej
PublikacjaPrzeprowadzono badania trawienia stali wysokostopowej w mieszaninie kwasu HF IHNO3 wykorzystując elektrochemiczna spektroskopie impedancyjną. W celu odwzorowania warunków naturalnych eksperyment przeprowadzono przy uzyciu DEIS w trybie galwanostatycznym z wypadkowym prądem równym zero. Wyznaczone zostały zmiany parametrów elektrycznych opisujących układ ew czasie zmian. Zaobserwowano wpływ stężenia HF na czas trwania procesu.
-
Electrochemical characterization of Prussian blue type nickel hexacyanoferrate redox mediator for potential application as charge relay in dye-sensitized solar cells
Publikacja -
Electrochemical Charakterization of Prussian blue type nickel hexacyanoferrate redox mediator for potential application as charge relay in dye-sensitized solar cells
PublikacjaMateriał nieorganiczny o mieszanym przewodnictwie elektronowo jonowym jakim jest heksacyjanożelazian (II,III) niklu (II) (NiHCF) rozpatrywany był jako potencjalny przenośnik ładunku w ogniwach słonecznych sensybilizowanych pigmentem (DSSC). Stwierdzono, że reakcje redoksowe NiHCF są szybkie i odwracalne nie tylko w obecności elektrolitu wspomagającego ale również w stanie stałym. Użyteczność NiHCF zbadana została za pomocą tradycyjnego...
-
Electrochemical oscillations and bistability during anodic dissolution of vanadium electrode in acidic media—part I. Experiment
Publikacja -
Electrochemical oscillations and bistability during anodic dissolution of vanadium elektrode in acidic media. part 1. Experiment
PublikacjaDynamiczne niestabilności, oscylacje prądowe i bistabilność obserwowane były podczas anodowego roztwarzania elektrody wanadowej w trakcie badań wykorzystujących techniki stało i zmienno prądowe. Analizowany był wpływ warunków eksperymentalnych jak: stężenia kwasu, temperatury itd. Badania pozwoliły stworzyć diagramy przedstawiające regiony występowania oscylacji i bistabilności.
-
Evaluation of cavitation erosion–corrosion degradation of mild steel by means of dynamic impedance spectroscopy in galvanostatic mode
Publikacja -
Evaluation of cavitation erosion-corrosion degradation of mild steel by means of Dynamic Impedance Spectroscopy in galvanostatic mode
PublikacjaPrzedstawiono wyniki badań degradacji stali węglowych na skutek oddziaływania erozji-korozji kawitacyjnej. Do analizy wykorzystano technikę Dynamicznej Elektrochemicznej Spektroskopii Impedancyjnej w trybie galwanostatycznym, bliżej odwzrorowującym warunki naturalne. Do oceny stopnia degradacji posłużyły również funkcja ubytku masy MDPR oraz obrazy mikroskopowe SEM. Potwierdzono wpływ łączonej degradacji erozyjno-korozyjnej na...
-
Investigation of morphological and electrical properties of the PMMA coating upon exposure to UV irradiation based on AFM studies
PublikacjaCelem badania było określenie wpływu promieniowania ultrafioletowego na morfologię powierzchni powłoki i na jej właściwości elektryczne. Cienka powłoka z polimetakrylanu metylu została nałożona na podłoże stalowe metodą zanurzeniową. Oceny stanu przed ekspozycją UV i w jej trakcie dokonywano przy użyciu mikroskopu sił atomowych. Na obrazach AFM zaobserwowano pojawienie się mikropęknięć. Celem zweryfikowania czy wykryte nieciągłości...
-
Investigations of pitting corrosion of magnesium by means of DEIS and acoustic emission
Publikacja -
On-line Impedance Monitoring of Direct Methanol Fuel Cell
PublikacjaW niniejszej pracy została przedstawiona technika badawcza Dynamiczna Elektrochemiczna Spektroskopia Impedancyjna w obszarze badań ogniw paliwowych. Obiektem badań było ogniwo paliwowe zasilane bezpośrednio metanolem. Badano on-line wpływ zmian warunków pracy na globalną impedancję ogniwa. Podczas pomiarów zmianie ulegała temperatura, natężenia przepływu utleniacza oraz obciążenie.
-
Study of anticorrosion and microwave absorption properties of NiZn ferrite pigments
Publikacja -
Study of anticorrosion and microwave absprption properties of NiZn ferrite pigments
PublikacjaPurpose - The purpose of this paper is to report the electrochemical verification of anticorrosive properties of NiZn ferrites as pigments in protective coatings and evaluation of their microwave absorbing properties. Design/methodology/approach - Ferrites, represented by formula NixZn(1-x)Fe2O4, where x=0, 0.2, 0.4, 0.6, 0.8, 1.0, were synthesized using a ceramic method. The samples of ferrites were examined by X-ray diffraction...
-
Zwiększenie odporności stali austenitycznych poprzez obróbkę chemiczna powierzchni
PublikacjaPrzedstawiono wyniki badań elektrochemicznych stali stopowej 1.4301 w środowisku korozyjnym zawierającym jony chlorkowe. Powierzchnia stali została poddana przed badaniami różnym typom obróbki powierzchniowej. Porównano odporność na korozję wżerową stali poddanej trawieniu, trawieniu i pasywacji oraz samej pasywacji. Stwierdzono poprawę odporności stali poddanej dodatkowej obróbce powierzchniowej w stosunku do stali przygotowanej...
Rok 2010
-
Assessment of organic coating degradation via local impedance imaging
PublikacjaThe paper presents a new approach to organic coating condition evaluation at micrometer scale using localized impedance measurements. It is based on atomic force microscopy (AFM) in contact mode. Impedance is measured between conductive AFM tip and metal substrate covered with organic coating. A single-frequency voltage perturbation signal is applied between the electrodes and current response signal is registered. As the tip is...
-
Corrosion resistance evaluation of Al‐based alloys by means of dynamic electrochemical impedance spectroscopy
Publikacja
wyświetlono 7226 razy