Filtry
wszystkich: 1683
wybranych: 1534
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: NUMERICAL SIMULATIONS, POLLUTION MIGRATION, METHOD OF FINITE VOLUMES, DISPERSION
-
Greedy Multipoint Model-Order Reduction Technique for Fast Computation of Scattering Parameters of Electromagnetic Systems
PublikacjaThis paper attempts to develop a new automated multipoint model-order reduction (MOR) technique, based on matching moments of the system input–output function, which would be suited for fast and accurate computation of scattering parameters for electromagnetic (EM) systems over a wide frequency band. To this end, two questions are addressed. Firstly, the cost of the wideband reduced model generation is optimized by automating a...
-
DETEKCJA FAL UDERZENIOWYCH W UKŁADACH ŁOPATKOWYCH CZĘŚCI NISKOPRĘŻNYCH TURBIN PAROWYCH
PublikacjaW artykule przedstawiono wyniki numerycznych symulacji okołodźwiękowego przepływu pary przez ostatnie stopnie części niskoprężnej turbiny o mocy 50 MW. Celem przeprowadzonych symulacji była detekcja oraz lokalizacja fali uderzeniowej, występującej dla przyjętej geometrii układu łopatkowego. Przeanalizowano również wpływ zmiany wartości ciśnienia na wlocie do rozpatrywanych stopni turbiny na maksymalną wartość...
-
Tuning a Hybrid GPU-CPU V-Cycle Multilevel Preconditioner for Solving Large Real and Complex Systems of FEM Equations
PublikacjaThis letter presents techniques for tuning an accelerated preconditioned conjugate gradient solver with a multilevel preconditioner. The solver is optimized for a fast solution of sparse systems of equations arising in computational electromagnetics in a finite element method using higher-order elements. The goal of the tuning is to increase the throughput while at the same time reducing the memory requirements in order to allow...
-
On weak solutions of the boundary value problem within linear dilatational strain gradient elasticity for polyhedral Lipschitz domains
PublikacjaWe provide the proof of an existence and uniqueness theorem for weak solutions of the equilibrium problem in linear dilatational strain gradient elasticity for bodies occupying, in the reference configuration, Lipschitz domains with edges. The considered elastic model belongs to the class of so-called incomplete strain gradient continua whose potential energy density depends quadratically on linear strains and on the gradient of...
-
Modeling of the Two-Dimensional Flow Caused by Sea Conditions and Wind Stresses on the Example of Dead Vistula
PublikacjaThe article presents the results of two-dimensional modeling of flows caused by the sea conditions and wind stresses on the example of Dead Vistula. Based on the available bathymetric data, a numerical model of the river section was created, which was supplemented with data on the position of the water table depending on hydrometeorological conditions. To describe the flow field in steady conditions, a simplified model of two-dimensional...
-
Numerical analyses of novel prefabricated structural wall panels in residential buildings based on laboratory tests in scale 1:1
PublikacjaThe paper presents experimental and numerical investigations on novel prefabricated composite building wall panels for residential building constructions. The wall panels were composed of reinforced concrete ribbed elements with the core from the EPS foam as the thermal insulation. The wall panels in the full-scale 1:1 were subjected to vertical loads. In the first step, the experiments were analysed with simple usual static methods....
-
Analiza porównawcza procesów tłumienia i wygładzania fali ciśnienia w trakcie nieustalonego przepływu w rurociągach wykonanych z różnych materiałów.
PublikacjaUderzenie hydrauliczne jest uważane za jeden z najważniejszych problemów nieustalonego przepływu w przewodach, dlatego nadal stanowi obiekt badań wielu naukowców. To zagadnienie może być badane na dwóch poziomach: praktycznym i teoretycznym. W artykule zaprezentowane zostały wyniki badań doświadczalnych przeprowadzonych na stanowisku pomiarowym nieustalonego przepływu, funkcjonującym w Laboratorium Hydraulicznym Wydziału Inżynierii...
-
ENHANCED EVAPORATION OF THE DROPLETS OF CONDENSATE IN THE ASYMMETRICAL SHOCK WAVE ZONE
PublikacjaIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages [4,5]. The formation and evolution of these droplets lower the performance of the wet stages of the turbines, and their effects on the efficiency are collectively known as wetness losses [4]. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current....
-
Dimensional Synthesis of Coupled-Resonator Pseudoelliptic Microwave Bandpass Filters with Constant and Dispersive Couplings
PublikacjaIn this paper, we propose a novel technique for the dimensional synthesis of coupled-resonator pseudoelliptic microwave filters with constant and dispersive couplings. The proposed technique is based on numerical simulations of small structures, involving up to two adjacent resonators, and it accounts for a loading effect from other resonators by replacing them with terminations coupled through appropriately scaled inverters. The...
-
Numerical Characterization of Thresholds for the Focusing 1d Nonlinear Schrödinger Equation
PublikacjaThe focusing nonlinear Schrödinger equation arises in various physical phenomena and it is therefore of interest to determine mathematical conditions on the initial data that guarantee whether the corresponding solution will blow up in finite time or exist globally in time. We focus on solutions to the mass‐supercritical nonlinear Schrödinger equation (1) in 1D case. In particular, we investigate numerical thresholds between blow...
-
Numerical solution of threshold problems in epidemics and population dynamics
PublikacjaA new algorithm is proposed for the numerical solution of threshold problems in epidemics and population dynamics. These problems are modeled by the delay-differential equations, where the delay function is unknown and has to be determined from the threshold conditions. The new algorithm is based on embedded pair of continuous Runge–Kutta method of order p = 4 and discrete Runge–Kutta method of order q = 3 which is used for the...
-
DYNAMIC ANALYSIS OF THE IMPACT OF VIBRATION ON HISTORICAL BUILDINGS - AN OWN PROJECT OF EXTERNAL STAIRCASE
PublikacjaThis article presents numerical simulations that concern modeling of interaction of the external staircase’s construction with the observation deck on historic water tower located at Gdansk University of Technology. The interaction occurring according to various methods of the staircase's construction support on the wall of the historic tower was compared. The external staircase that allows for entering onto the monument was subjected...
-
Numerical Model of Surface and Quasi-Spherical Sea Noise and Its Application to Analysis of DIFAR Systems
PublikacjaVarious types of passive sonar systems are used to detect submarines. These activities are complex and demanding. Therefore, computer simulations are most often used at the design stage of these systems. For this reason, it is also necessary to simulate the acoustic ambient noise of the sea. The article proposes a new numerical model of surface and quasi-spherical sea noise and presents its statistical parameters. The results of...
-
Electronically Excited States in Solution via a Smooth Dielectric Model Combined with Equation-of-Motion Coupled Cluster Theory
PublikacjaWe present a method for computing excitation energies for molecules in solvent, based on the combination of a minimal parameter implicit solvent model and the equation-of-motion coupled-cluster singles and doubles method (EOM-CCSD). In this method, the solvent medium is represented by a smoothly varying dielectric function, constructed directly from the quantum mechanical electronic density using only two tunable parameters. The...
-
Rozkład naprężeń mechanicznych w łyżce o szerokości 500 mm, przeznaczonej do koparki podsiębiernej
PublikacjaW artykule zaprezentowano optymalizację kształtu łyżki koparki przedsiębiernej z wykorzystaniem analizy wytrzymałościowej. Analizę oparto na trójwymiarowym modelu konstrukcji łyżki z zastosowaniem metody elementów skończonych (MES). Opracowanie wspomnianej metody pozwoliło na modyfikację konstrukcji łyżki, która dała w efekcie obniżenie naprężeń złożonych w newralgicznych obszarach konstrukcji łyżki. Przedstawiona analiza okazała...
-
Limits of enhanced of macro- and meso-scale continuum models for studying size effect in concrete under tension
PublikacjaThe paper investigates a mechanical quasi-static size effect in concrete during splitting tension at the macro- and meso-level. In experiments, five different diameters of cylindrical concrete specimens were tested. Twodimensional plane strain finite element (FE) simulations were carried out to reproduce the experimental size effect. The size effect in experiments by Carmona et al. was also simulated. Two enhanced continuum concrete...
-
Theoretical and experimental analysis of guided wave propagation in plate-like structures with sinusoidal thickness variations
PublikacjaGuided waves have attracted significant attention for non-destructive testing (NDT) and structural health monitoring (SHM) due to their ability to travel relatively long distances without significant energy loss combined with their sensitivity to even small defects. Therefore, they are commonly used in damage detection and localization applications. The main idea of incorporating guided waves in NDT and SHM is based on processing...
-
Projektowanie układów ramowych z zastosowaniem analizy wrażliwości
PublikacjaW pracy przedstawiono przykład projektowania układów ramowych z zastosowaniem analizy wrażliwości. Rozważane układy ramowe rozwiązano autorskim programem napisanym w środowisku MATLAB, metodą elementów skończonych. Badano wpływ zmiany modułu Younga oraz wpływ zmiany wielkości przekroju poprzecznego na wybrane przemieszczenia ramy. Przedstawiono wyniki dla analizy wrażliwości jedno i wieloparametrycznej.
-
A 3D-FEM mesh technique for fast analysis of waveguide problems containing rotatable tuning elements
PublikacjaIn this paper a meshing technique for 3D Finite Element Method is presented. It allows for fast analysis and optimization of the waveguide structures, which contain rotatable tuning elements. In the proposed procedure a thin layer of varying cylindrical mesh buffer is introduced in order to reuse unchanged mesh and FEM matrices in the rest of the domain.
-
Fast surrogate-assisted frequency scaling of planar antennas with circular polarisation
PublikacjaIn this work, the problem of computationally efficient frequency scaling (re-design) of circular polarisation antennas is addressed using surrogate-assisted techniques. The task is challenging and requires the identification of the optimum geometry parameters to enable the operation of the re-designed structure at a selected (required) centre frequency. This involves handling several performance figures such as the antenna gain,...
-
Modelling and Analysis of the Positioning Accuracy in the Loading Systems of Mobile Cranes
PublikacjaIn this work, the authors analyse the influence of the order and range of sequential movements of a crane's working members on the accuracy of the final cargo positioning. The analysis was conducted on the basis of a specially developed method in which the authors proposed the introduction of a geometrical indicator of positioning the load in the intermediate positions (after completing each movement sequence) and in the target...
-
Study of Icosahedral Clusters in Close-packed Simple Liquids
PublikacjaThe local structure of liquid copper was determined using Steinhardt order parameters, with particular attention paid to icosahedral clusters. The positions of atoms were obtained from three sets of molecular dynamics simulations, with the forces obtained from: the Sutton-Chen (SC) potential, the Naval Research Laboratory total energy tight-binding (NRL-TB) method and the divide-and-conquer learn-on-the-fly (DCLOTF) method, respectively....
-
Remarks on steam condensation modeling related to steam turbine large output
PublikacjaIn the paper numerical simulations have been performed to predict the performance of the diferent steam models. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine equipped with the so-called Baumann stage. For numerical analysis three models have been finally used - the ideal steam model without...
-
Viscoplastic damage analysis of structures subjected to impact loading. Plate and shell structures. - Ł. Pyrzowski.
PublikacjaThe work presents the investigation in the response of plate-shell structures subjected to impact loading (gas mixture explosions). This phenomenon is studied in the context of its mechanical aspects, mainly the ductile fracture prediction. The work starts with the literature review and the description of theories, which are nowadays the most popular in the damage and failure modelling. After selecting the theoretical models and...
-
Experimental and Computational Analysis of the Ship Propeller in Open Water Conditions for Inclined Flow
PublikacjaThe paper presents the results of computational analyses simulating the open water tests of ship propeller in inclined flow. The results of computations are compared with the results of corresponding experimental analyses carried out in the towing tank of Ship Design and Research Centre (CTO S.A.). The object of the research was the model propeller identified as CP469. The aim of the study was to validate the results of numerical...
-
Dynamics of the small-span railway bridge under moving loads
PublikacjaThe paper presents the results of dynamic analysis of the small-span railway bridge, subjected to an action of moving trains. Numerical simulations were performed using three different load models: series of moving forces, series of moving single-mass and double-mass oscillators. The parameters of the vehicle were taken from the existing EN57 train. The parameters of the bridge were taken from the existing steel span of 10,24 m...
-
Broadening the scope of measurement and analysis of vibrations of an organ pipe employing intensity probe, simulations, and highspeed camera
PublikacjaThis paper shows an integrated approach to measure, analyze, and model phenomena occurring in an organ pipe driven by pressurized air. The aim of this paper is two-fold, i.e., to measure the pressure signal and the intensity field around the mouth by means of an intensity probe and to visualize and observe the motion of the air jet, which represents the excitation mechanism of the system. This is realized through two techniques,...
-
Modelling and Measurement of Folk Guitar: Truss Rod and Strings in Numerical Analysis of Tone
PublikacjaThe study makes an attempt to model a complete vibrating guitar including its non-linear features, specifically the tension-compression of truss rod and tension of strings. The purpose of such a model is to examine the influence of design parameters on tone. Most experimental studies are flawed by uncertainties introduced by materials and assembly of an instrument. Since numerical modelling of instruments allows for deterministic...
-
Microbial and chemical quality assessment of the small rivers entering the South Baltic. Part II: Case study on the watercourses in the Puck Bay catchment area
PublikacjaDue to its location, Puck Bay is an area particularly vulnerable to pollution of anthropogenic origin. The aim of the study was to assess the water quality of small watercourses entering the inner part of Puck Bay. The paper presents the results of chemical and microbiological analyses of 10 rivers and canals at their estuaries located on the western shore of the internal Puck Bay. The following environmental parameters were analyzed:...
-
Towards Robust Identification of Nonstationary Systems
PublikacjaThe article proposes a fast, two-stage method for the identification of nonstationary systems. The method uses iterative reweighting to robustify the identification process against the outliers in the measurement noise and against the numerical errors that may occur at the first stage of identification. We also propose an adaptive algorithm to optimize the values of the hyperparameters that are crucial for this new method.
-
Oddziaływania taboru na mosty kolejowe przy zmiennych parametrach ruchu
PublikacjaW pracy poruszono zagadnienia związane z identyfikacją oraz modelowaniem układu dynamicznego most-pojazd ruchomy. Za element szczególnie istotny uznano czynnik obciążający. Opracowano i wdrożono metodykę identyfikacji cech dynamicznych rzeczywistego pojazdu szynowego. Eksperyment badawczy przeprowadzono dla jednostki trakcyjnej EN57, jednak nie ma żadnych ograniczeń w stosowaniu metody dla innego, konwencjonalnego taboru szynowego....
-
Some Optimization Methods for Simulations in Volunteer and Grid Systems
PublikacjaIn this chapter, some optimization methods have been presented for improving performance of simulations in the volunteer and grid computing system called Comcute. Some issues related to the cloud computing can be solved by presented approaches as well as the Comcute platform can be used to simulate execution of expensive and energy consuming long-term tasks in the cloud environment. In particular, evolutionary algorithms as well...
-
Influence of Flat Lapping Kinematics on Machinability of Ceramics
PublikacjaNew tools for flat grinding of ceramics are presented in the paper. Electroplated CBN tools (B64 and B107) were used in a modified single-disc lapping machine configuration. The results from experiments, such as the material removal rate and surface roughness parameters are presented and analyzed. Numerical simulations, based on the model for the shape error and tool wear estimation in machining with flat lapping kinematics, are...
-
Parametric method applicable in calculating breakout force and time for lifting axisymmetric objects from seabed.
PublikacjaThe issue of calculating parameters for lifting objects of axisymmetric shapes from the seabed is studied. The article presents the results of numerical simulation examination of the equation formulated by Foda for the force needed to extricate the object from the seabed depending on soil and water parameters, extrication speed, and object diameter. The simulations were performed within the range of parameters characteristic for...
-
How much a geometrical model of a honeycomb seal can be simpli ed in the CFD calculation
PublikacjaThis paper presents the inuence of geometry simplication on the results obtained in the computational fluid dynamics simulation. The subject of simulation was part of the honeycomb seal located at the inlet to high pressure part of a steam turbine. There were three different geometrical models assumed in the calculations. First one was two-dimensional case and two others were three dimensional, one with the radius of curvature...
-
LINEAR CHARACTERISTICS OF THE SLOSHING PHENOMENON FOR THE PURPOSE OF ON-BOARD SHIP'S STABILITY ASSESSMENT
PublikacjaThe paper presents results of experimental research and numerical simulations of the sloshing phenomenon. The research was focused on computation of the heeling moment affecting stability of a vessel. The proposed linearisation enables application of the results to the assessment of the ship's stability. The dependence of the heeling moment upon localisation of a tank in the ship's hull is analysed. The heeling moment obtained...
-
A new duty cycles calculation method in pulse width modulation for direct matrix converters based on the shape function concept
PublikacjaPaper presents a new approach to duty cycle calculation in pulse width modulation for direct matrix converters. The essence of the proposed method is the use of elementary shape function of finite element. The algorithm for calculating the duty cycles was reduced to simple operations on the coordinates of input and output voltage vectors without trigonometric functions.
-
New Concept of Numerical Ship Motion Modelling for Total Ship Operability Analysis by Integrating Ship and Environment Under One Overall System
PublikacjaThe paper presents a new concept of overall ship motion modelling for application to total ship operability. The delivered model is a multi-phase and includes both submerged part of ship’s hull and the surrounding water as a unique body. The Discrete Finite Element Method is applied. The model is successfully examined and illustrated for a selected AHTS.
-
Historical carpentry corner log joints—Numerical analysis within stochastic framework
PublikacjaThe paper presents the results of numerical analysis performed on historical, traditional carpentry corner logjoints of two basic topologies: the short-corner dovetail connection and the saddle notch connection. These types of carpentry joints are commonly used in currently preserved objects of wooden architecture. All connections have been modelled in pinewood, which has been defined in the Finite Element software MSC.Marc/Mentat...
-
Inception and Propagation of Electrical Trees in the Presence of Space Charge in HVAC Extruded Cables
PublikacjaThis paper presents the space charge impact on the inception and propagation of electrical trees in cross-linked polyethylene (XLPE) insulation via simulations and experimentation. A 3D finite element analysis (FEA)-based modeling is proposed to simulate electrical trees via a needle embedded on the XLPE insulation. The proposed FEA model demonstrates the influence of the space charge magnitude and polarity on the initiation of...
-
Comparison of Average Energy Slope Estimation Formulas for One-dimensional Steady Gradually Varied Flow
PublikacjaTo find the steady flow water surface profile, it is possible to use Bernoulli’s equation, which is a discrete form of the differential energy equation. Such an approach requires the average energy slope between cross-sections to be estimated. In the literature, many methods are proposed for estimating the average energy slope in this case, such as the arithmetic mean, resulting in the standard step method, the harmonic mean and...
-
Experiment-aided virtual prototyping to minimize tool-workpiece vibration during boring of large-sized structures
PublikacjaThe paper presents the author's method of solving the problems of vi-bration suppression during boring of large-sized workpieces by means of an in-novative method of adjusting the rotational speed of the boring bar. It consists in selecting the spindle speed in accordance with the results of the cutting process simulation. The method includes identification of the model of the finite element method of the boring bar. The Root Mean...
-
Determination of equivalent circuit parameters of an induction motor using field calculation software
PublikacjaSimulation of the drive system comprising a power electronic converter and an induction motor requires that the equivalent circuit parameters of the motor are known. These parameters can be either measured or calculated. A method of calculation of self and mutual inductances that are parameters of a polyphase model of the motor is presented in the paper. All self-inductances and mutual inductances have been calculated using the...
-
Numerical Comparison of Damping Amplification Effects Obtained in Neighborhood of a Mechanism Singular Position - Viscous and Electromagnetic Cases
PublikacjaIn the paper, results of numerical investigations are presented. A continuous beam is considered as the main vibrating element. Two energy dissipations methods are compared: viscous dampers and DC generators. To increase the damping effectiveness, velocity amplification is proposed, i.e., a mechanism is introduced between the beam and the damping element, and the mechanism configuration is set as closed to the singular position...
-
Ranking of Generation Source Locations by a Hybrid Multi-Criteria Method
PublikacjaThe paper presents a ranking of the locations of eight renewable energy sources (RES) made using a hybrid multi-criteria analysis method. The method is a combination of the analytical hierarchical process (AHP) method and numerical taxonomy. The considered generating sources, i.e. solar plants, biogas plants, and wind farms are sources that will significantly contribute to implementing the provisions of the energy and climate package...
-
The role of atmospheric precipitation in introducing contaminants to the surface waters of the Fuglebekken catchment, Spitsbergen.
PublikacjaAlthough the Svalbard Archipelago is located at a high latitude, far from potential contaminant sources, it is not free from anthropogenic impact. Towards the Fuglebekken catchment, in the southern part of Spitsbergen, north of Hornsund fjord, contaminants can be transported from mainland pollution sources. In the precipitation and surface water collected in the catchment, the following elements were detected and quantified: Ag,...
-
Migration of trace elements and radioisotopes to various fractions of solid wastes generated as a result of the sewage sludge incineration process
PublikacjaThe research was aimed at providing new knowledge in the field of chemical characteristics of solid waste generated in the process of combustion of sewage sludge in fluidized bed furnaces. The research material consisted of disposed fluidized beds (DFB), sewage sludge ash (SSA) and air pollution control residues (APC) from three Polish installations for the thermal treatment of sewage sludge. Natural radionuclides as well as anthropogenic...
-
State of the art in the field of emission reduction of sulphur dioxide produced during coal combustion
PublikacjaThe need for clean coal technologies to reduce the adverse environmental impact of coal combustion products has been grounded. The article deals with information concerning present and future technologies, directed towards the struggle against air pollution by SO2, produced during coal combustion. Their classification and critical rating from economical and technological points of views (including those developed by authors) have...
-
HYBRID REDUCED MODEL OF ROTOR
PublikacjaIn the paper, the authors describe the method of model reduction of a rotor system. The proposed approach enables to obtain a low order model including e.g. nonproportional damping or the gyroscopic effect. This method is illustrated using the example of a rotor system. First, a model of the system was built without gyroscopic and damping effects by using the rigid finite element method. Next, this model was reduced. Finally, two...
-
Exact modal absorbing boundary condition for waveguide simulations - discrete Green's function approach
PublikacjaA modal absorbing boundary condition (ABC) based on the discrete Green's function (DGF) is introduced and applied for termination of waveguides simulated by means of the finite-difference time-domain (FDTD) method. The differences between the developed approach and implementations already demonstrated in the literature are presented. By applying DGF, a consistent theoretical approach to modal ABC in the FDTD method is obtained....