Filtry
wszystkich: 1212
wybranych: 958
-
Katalog
- Publikacje 958 wyników po odfiltrowaniu
- Czasopisma 98 wyników po odfiltrowaniu
- Konferencje 2 wyników po odfiltrowaniu
- Osoby 98 wyników po odfiltrowaniu
- Wynalazki 1 wyników po odfiltrowaniu
- Projekty 7 wyników po odfiltrowaniu
- Kursy Online 12 wyników po odfiltrowaniu
- Wydarzenia 1 wyników po odfiltrowaniu
- Dane Badawcze 35 wyników po odfiltrowaniu
Filtry wybranego katalogu
Wyniki wyszukiwania dla: maritime%20transportation
-
ASSESSING THE POTENTIAL REPLACEMENT OF MINERAL OIL WITH ENVIRONMENTALLY ACCEPTABLE LUBRICANTS IN A STERN TUBE BEARING: AN EXPERIMENTAL ANALYSIS OF BEARING PERFORMANCE
PublikacjaT his study compares the performance of a plain bearing, with a similar structure to a tail shaft stern bearing, lubricated with either mineral oil or an environmentally acceptable lubricant (EAL). The main characteristic of the bearing is its length/diameter ratio of <1. Measurements are carried out with the bearing operating under loads from 0.5 to 1 MPa and seven speeds ranging from 1 to 11 rev/s. The bearing lubricated...
-
NEW DESIGNS OF MAGNETIC FLUID SEALS FOR RECIPROCATING MOTION
PublikacjaT he operating conditions of magnetic fluid seals during reciprocating motion are so different from those observed in rotating motion that the use of their conventional structures for reciprocating motion seals yields no good results. The analysis of the sealing mechanism of magnetic fluid seals in reciprocating motion shows that the operation of these seals is affected by the carry-over phenomenon and magnetic fluid...
-
PARAMETRIC ANALYSIS OF THE EFFICIENCY OF THE COMBINED GAS-STEAM TURBINE UNIT OF A HYBRID CYCLE FOR THE FPSO VESSEL
PublikacjaA thermal diagram of the combined gas‒steam turbine unit of a hybrid cycle, which is an energy complex consisting of a base gas turbine engine with a steam turbine heat recovery circuit and a steam-injected gas turbine operating with overexpansion, is proposed. A mathematical model of a power plant has been developed, taking into consideration the features of thermodynamic processes of simple, binary, and steam-injected...
-
INFLUENCE OF SOLID PARTICLE CONTAMINATION ON THE WEAR PROCESS IN WATER LUBRICATED MARINE STRUT BEARINGS WITH NBR AND PTFE BUSHES
PublikacjaThis paper reports on a study of the influence of solid particle contamination on the wear process in water-lubricated slide bearings (steel-acrylonitrile-butadiene rubber (NBR) and steel- polytetrafluoroethylene (PTFE)). To compare the wear of the shaft journal and bushes (NBR and PTFE) when lubricated with fresh water and contaminated water, an experiment was carried out to identify key factors that influence the state of wear...
-
EVALUATION OF EFFECTIVENESS OF WATERJET PROPULSOR FOR A SMALL UNDERWATER VEHICLE
PublikacjaT he goal of the project described is to replace the existing propulsion system of a small underwater vehicle with a solution less prone to mechanical damage and ensuring a lower risk of the entanglement of fibrous objects suspended in the body of water. Four typical marine screws are utilised in the current design of the vehicle. One possible solution of the problem is the application of waterjet propulsors located...
-
The influence of selected strain-based failure criteria on ship structure damage resulting from a collision with an offshore wind turbine monopile
PublikacjaOffshore wind farms are developing well all over the world, providing green energy from renewable sources. The evaluation of possible consequences of a collision involves Finite Element computer simulations. The goal of this paper was to analyse the influence of selected strain-based failure criteria on ship damage resulting from a collision with an offshore wind turbine monopile. The case of a collision between an offshore supply...
-
Performance and Emission Modelling and Simulation of Marine Diesel Engines using Publicly Available Engine Data
PublikacjaTo analyse the behaviour of marine diesel engines in unsteady states for different purposes, for example to determine the fuel consumption or emissions level, to adjust the control strategy, to manage the maintenance, etc., a goal-based mathematical model that can be easily implemented for simulation is necessary. Such a model usually requires a wide range of operating data, measured on a test stand. This is a time-consuming process...
-
Experimental Research on Insufficient Water Lubrication of Marine Stern Tube Journal Bearing with Elastic Polymer Bush
PublikacjaWater-lubricated bearings with polymer bushes are steadily gaining popularity due to their advantages, including environmental friendliness, relatively simple construction and long-term operation. Nevertheless, in practice instances of damage to such bearings occur due to insufficient or absent flow of the lubricating agent. In this study, experimental tests established that elastic polymer bush bearing is capable of operating...
-
Diagnostic Model of Crankshaft Seals
PublikacjaT he paper presents a research stand being a diagnostic model of radial lip seals used, among others, on crankshafts of piston combustion engines in order to identify the correctness of their operation. The possibility of determining the technical condition of lip seals on the basis of the proposed coefficient of correctness of operation has been described. T he basic features of seals influencing their correctness of...
-
SPECTRAL RESPONSE OF STATIONARY JACK-UP PLATFORMS LOADED BY SEA WAVES AND WIND USING PERTURBATION METHOD
PublikacjaThe paper addresses non-linear vibrations of offshore jack-up drilling platforms loaded by sea waves and wind in their stationary condition using the perturbation method. Non-linearity of dynamic equations of motion for fixed offshore platforms yields from two factors. The first is load excitation generating non-linear velocity coupling in a dynamic system. This coupling is inherent in the modified Morison equation, involving the...
-
Prediction of Weld Deformations by Numerical Methods - Review
PublikacjaThe welding process is the basic technique of joining in the shipbuilding industry. This method generates welding distortions that cause a lot of problems during the manufacturing process due to both the time and cost of straightening as well as their influence on later stages of production. Proper preparation of welding processes plays a growing role in the shipbuilding industry and the development of calculating tools is being...
-
Heave Plates with Holes for Floating Offshore Wind Turbines
PublikacjaThe paper presents an innovative solution which is heave plates with holes. The long-known heave plates are designed to damp the heave motion of platforms. They are most often used for Spar platforms. The growing interest in this type of platform as supporting structures for offshore wind turbines makes it necessary to look for new solutions. Based on the available literature and the authors’ own research, it was concluded that...
-
On the Use of Selected 4th Generation Nuclear Reactors in Marine Power Plants
PublikacjaThis article provides a review of the possibility of using different types of reactors to power ships. The analyses were carried out for three different large vessels: a container ship, a liquid gas carrier and a bulk carrier. A novelty of this work is the analysis of the proposal to adapt marine power plants to ecological requirements in shipping by replacing the conventional propulsion system based on internal combustion engines...
-
50’ Sail Catamaran with Hybrid Propulsion, Design, Theoretical and Experimental Studies
PublikacjaThe development of modern lithium batteries and propulsion systems now allows the use of complex propulsion systems for vessels of various sizes. As part of the research and implementation project, a parallel hybrid drive system was designed, built and then tested in the laboratory. The experimental studies conducted allowed for the measurements of power, fuel consumption and electric power distribution in various operating modes...
-
Application of the corrosion tester in corrosion tests using the acoustic emission method.
PublikacjaThe article presents an innovative method of corrosion tests using the acoustic emission method and the corrosion tester. The problem of corrosion occurring in ballast tanks and tanks carrying petroleum products is discussed. The acoustic method is presented which, due to the use of a unique corrosion tester, is used to monitor the course of corrosion processes in steel. The principle of operation of the corrosion tester, its construction...
-
Analysis of the Hydrodynamic Properties of the 3-Column Spar Platform for Offshore Wind Turbines
PublikacjaThe article presents a design of a floating platform for offshore wind turbines. The concept is a modification of the Spar design and consists of three variable section columns connected to each other by a ballast tank in the lower part of the platform. This solution makes it possible to influence the position of the centre of buoyancy and the centre of mass of the structure. Compared to the classic Spar platform structure, the...
-
An integrated hydraulic drive system of a novel device for launching lifeboats from large passenger ship
PublikacjaArtykuł przedstawia zintegrowany układ napędu i sterowania hydraulicznego systemu ewakuacyjnego składającego się z wyciągu łańcuchowego z zamocowanymi na nim łodziami ratunkowymi oraz furto-rampy rufowej. Zastosowana tu furto-rampa z elementem wypornościowym umożliwia zwiększenie jej funkcji do samoczynnego dostosowania kąta jej wychylenia roboczego w przypadku znacznego przegłębienia statku na dziób. Przedstawiony układ hydrauliczny...
-
Processing data on sea bottom structure obtained by means of the parametric sounding
PublikacjaThe aim of the paper is to analyze data obtained during sounding the Gdansk Bay sea bed by means of the parametric echo-sounder. The accuracy of the sea bottom structure investigation needs correct configuration of research equipment and proper calibration of peripheral devices (GPS, heading sensor, MRU-Z motion sensor and navigation instruments which provide necessary data to bathymetrical measurement system, enabling its work...
-
Influence of pitting corrosion on strength of steel ships and offshore structures
PublikacjaPraca dotyczy wpływu korozji wżerowej na własności mechaniczne stali o zwykłej i podwyższonej wytrzymałości oraz na wytrzymałość stalowych konstrukcji przy obciążeniach statycznych i quasi- statycznych. Artykuł oparty jest głównie na japońskich publikacjach. W próbie rozciągania, korozja wżerowa obniża nieznacznie obciążenie odpowiadające granicy plastyczności Re(nieznacznie) i wytrzymałości na rozciąganie Rm (silniej, redukuje...
-
Hybrid Finite Element Method Development for Offshore Structures’ Calculation with the Implementation of Industry Standards
PublikacjaIn the design process of offshore steel structures, it is typical to employ commercial calculation codes in which simulation and evaluation of results are performed on the basis of the available standards (e.g. API, DNV, Lloyds). The modeling and solution rely on finite element methods and cover the simulation of the structure’s properties along with the influence of the marine environment – sea currents, wave and wind loading,...
-
Blade Section Prpfile Array Lifting Surface Design Method for Marine Screw Propeller Blade
PublikacjaThe lifting surface model is widely used in screw propeller design and analysis applications. It serves as a reliable tool for determination of the propeller blade mean line and pitch distribution. The main idea of this application was to determine the blade shape that would satisfy the kinematic boundary condition on its surface with the prescribed bound circulation distribution over it. In this paper a simplified lifting surface...
-
REVIEW OF WEATHER FORECAST SERVICES FOR SHIP ROUTING PURPOSES
PublikacjaWeather data is nowadays used in a variety of navigational and ocean engineering research problems: from the obvious ones like voyage planning and routing of sea-going vessels, through the analysis of stability-related phenomena, to detailed modelling of ships’ manoeuvrability for collision avoidance purposes. Apart from that, weather forecasts are essential for passenger cruises and fishing vessels that want to avoid the risk...
-
Design of Jack-up Platform for 6 MW Wind Turbine: Parametric Analysis Based Dimensioning of Platform Legs
PublikacjaThe article presents the results of the research conducted within the framework of the project entitled WIND-TU-PLA (ERA-NET, MARTEC II), the general aim of which was to design and analyse supporting structures for wind turbines intended for operation on the South Baltic area. The research part described in the article aimed at developing a preliminary design for a jack-up platform which can operate on water areas with depth of...
-
Robust Model Predictive Control for Autonomous Underwater Vehicle – Manipulator System with Fuzzy Compensator
PublikacjaThis paper proposes an improved Model Predictive Control (MPC) approach including a fuzzy compensator in order to track desired trajectories of autonomous Underwater Vehicle Manipulator Systems (UVMS). The tracking performance can be affected by robot dynamical model uncertainties and applied external disturbances. Nevertheless, the MPC as a known proficient nonlinear control approach should be improved by the uncertainty estimator...
-
A method to determine the tightening sequence for standing rigging of a mast
PublikacjaThe article proposes an alternative method to determine the sequence of generation of pre-tension forces in standing rigging of a mast. The proposed approach has been verified on both a virtual simulation experiment and laboratory tests. In this method, the desired tension values are obtained using the influence matrix which allows to calculate the effect of tension change in an individual rope on the tension distribution in the...
-
Investigation of the Combustion Processes in the Gas Turbine Module of an FPSO Operating on Associated Gas Conversion Products
PublikacjaIn this paper, we consider the issue of thermo-chemical heat recovery of waste heat from gas turbine engines for the steam conversion of associated gas for offshore vessels. Current trends in the development of offshore infrastructure are identified, and the composition of power plants for mobile offshore drilling units and FPSO vessels is analyzed. We present the results of a comparison of power-to-volume ratio, power-to-weight...
-
ANALYSIS OF THE PROJECT OF INNOVATIVE FLOATING TURBINE
PublikacjaThe design of a floating, innovative device for river water aeration and conversion of mechanical energy to electrical energy required the analysis of a number of geometrical and dynamic features. Such an analysis may be carried out on the basis of existing methods of numerical fluid mechanics. Models of pressures, forces and torques characteristic for the conversion of watercourse energy were developed for two basic concepts of...
-
Parametric method applicable in calculating breakout force and time for lifting axisymmetric objects from seabed.
PublikacjaThe issue of calculating parameters for lifting objects of axisymmetric shapes from the seabed is studied. The article presents the results of numerical simulation examination of the equation formulated by Foda for the force needed to extricate the object from the seabed depending on soil and water parameters, extrication speed, and object diameter. The simulations were performed within the range of parameters characteristic for...
-
Selected Issues of Hybrid Outboard Motors
PublikacjaThe aim of the research reported in the article was designing a hybrid drive system based on an outboard internal combustion engine offered by a selected producer and testing its operating characteristics. The article presents different designs of this type of drive which can be found in the literature and are available in the market. The designed hybrid outboard drive system was tested both on the laboratory test rig and in real...
-
A study on fibre-reinforced concrete elements properties based on the case of habitat modules in the underwater sills
PublikacjaHydrotechnical constructions are mostly objects functioning in extreme conditions and requiring a custom-made construction project. In the case of using prefabricated elements, it is required to develop production, transport, assembly, conservation and repair technology. Concerning the problem of concrete cracks, modern repair systems allow positive effects to be achieved in many cases of concrete elements repair. In this work...
-
Application of Stirling Engine Type Alpha Powered by the Recovery Energy on Vessels
PublikacjaThe Stirling engine is a device, in which thermal energy is transformed into mechanical without a contact between the heat carrier, and the working gas closed in the engine. Mentioned feature makes this type of engine very attractive for the use of the recovery energy, taken from other heat devices. One of the potential applications of Stirling engines is the use of thermal energy generated in the ship's engine room for producing...
-
Underwater Navigation Ssystem Based on Doppler Shift – Measurements and Error Estimations
PublikacjaA new acoustic navigation system was developed to determine the position and speed of moving underwater objects such as divers and underwater vehicles. The path of an object and its speed were determined by the Doppler shifts of acoustic signals emitted by a transmitter placed on the object and received by four hydrophones installed at the periphery of the monitored body of water. The position and speed measurements were affected...
-
Weldability of high strength steels in wet welding conditions
PublikacjaIn this paper are characterized problems of high strength steel weldability in underwater wet welding conditions. Water as a welding environment intensifies action of unfavourable factors which influence susceptibility to cold cracking of welded steel joints. The susceptibility to cold cracking of S355J2G3 steel and S500M steel in wet conditions was experimentally estimated (by using Tekken test). It was concluded that the steels...
-
Telemedicine - education and practice
PublikacjaArtykuł przedstawia wybrane elementy telemedycyny w zastosowaniu edukacyjnym oraz w praktyce lekarza. Przedstawiono zrealizowane projekty w ramach współpracy Katedry Inżynierii Biomedycznej Politechniki Gdańskiej i Akademiii Medycznej w Gdańsku.
-
Accuracy Of The GPS Positioning System In The Context Of Increasing The Number Of Satellites In The Constellation
Publikacja -
Position accuracy evaluation of the modernized Polish DGPS
Publikacja -
Application of an Autonomous/Unmanned Survey Vessel (ASV/USV) in Bathymetric Measurements
Publikacja -
Polish DGPS System: 1995–2017 – Study of Positioning Accuracy
Publikacja -
A Method for The Assessing of Reliability Characteristics Relevant to an Assumed Position-Fixing Accuracy in Navigational Positioning Systems
PublikacjaThis paper presents a method which makes it possible to determine reliability characteristics of navigational positioning systems, relevant to an assumed value of permissible error in position fixing. The method allows to calculate: availability , reliability as well as operation continuity of position fixing system for an assumed, determined on the basis of formal requirements - both worldwide and national, position-fixing accuracy....
-
GNSS INVENTORY OF HISTORIC NARROW-GAUGE RAILWAY LINE IN KOSZALIN UNDER EXTREMELY UNFAVORABLE MEASUREMENTS CONDITIONS FROM THE POINT OF VIEW OF SATELLITE SIGNALS AVAILABILITY
PublikacjaA team of academic researchers from the Gdańsk University of Technology, Gdynia Maritime University and the Polish Naval Academy have been working since 2009 on the methodology of using active GNSS geodetic networks for geodetic inventory of railways and on adapting this measurement technique for designing geometric layouts of railway and tram lines. Over the years, the team tested a variety of configurations of receivers and settings...
-
Three-dimensional geographically weighted inverse regression (3GWR) model for satellite derived bathymetry using Sentinel-2 observations
PublikacjaCurrent trends of development of satellite derived bathymetry (SDB) models rely on applying calibration techniques including analytical approaches, neuro-fuzzy systems, regression optimization and others. In most of the cases, the SDB models are calibrated and verified for test sites, that provide favourable conditions for the remote derivation of bathymetry such as high water clarity, homogenous bottom type, low amount of sediment...
-
Experimental research on over-laminated steel sandwich panel connection to determine the form of fatigue failure
PublikacjaThe novel means of transport need to meet rising both the economic and ecologic requirements. In recent years the International Maritime Organization (IMO) introduced new measure of ship energy efficiency (the EEDI index), as well as new regulations regarding higher quality of fuel (so called Tier limits). It resulted in much higher interest of the technological development of ships. One of the solution having great potential is...
-
Advanced super-hydrophobic polymer-based porous absorbents for the treatment of oil-polluted water
PublikacjaThe threat of environmental pollution caused by spilled oil is rapidly increasing along with the expansion of oil exploration, the development of maritime activities and industrial growth. Oil spill incidents usually affect seriously the ecosystem and human life. Therefore, the treatment and recovery of the oil spill have been considered as an ultra-important issue to protect the environment and to minimize its negative impacts...
-
The influence of the development of private air communication on the architecture and urban planning of the 21st century
PublikacjaIn the first part, the article describes the stages of the development of gyroplanes and the influence of wartime policy on the interest in light aircraft. Also presented are links and the possibilities of using gyroplanes in various sectors of the economy. The authors, based on source texts, present the current position of the aviation industry in the Polish economy and attempt to diagnose its development capabilities. As a result,...
-
Economical wood sawing with circular saw blades
PublikacjaMaterial- and energy-saving belong to the basic requirements which are imposed on the contemporary manufacturing processes. Since realization of those processes gives measurable profits not only economical but also ecological. In case of wood sawing with circular saw blades material- and energy-savings are dependent on total overall set of teeth (theoretical kerf) and teeth position accuracy in relation to the workpiece. Hence,...
-
3D Machine Vision System for Inspection of Contact Strips in Railway Vehicle Current Collectors
PublikacjaConstruction and technical condition of current collectors is crucial to reliability and safety of railway transportation. According to the Technical Specifications for Interoperability railway vehicles in the European Union should be equipped with carbon contact strips. Excessive wear or defects of contact strips degrade the capability of undisturbed power transmission, cause faster wear of contact wire, and can even result in...
-
Identification of safety hazards and their sources in tram transport
PublikacjaBoth in Poland and in most countries of the European Union, the tram infrastructure is extensively expanding. Contemporary low-floor trams are constructed according to different technical assumptions than typical railway vehicles or high floor trams. In Poland such vehicles rides often on lines designed according to standards developed to the classical vehicles. At the same time, the intensity of road traffic and the number of...
-
Ensuring sustainable development of urban public transport: A case study of the trolleybus system in Gdynia and Sopot (Poland)
PublikacjaElectromobility is a vital tool in reducing the environmental impact of transportation. A technologically mature means of public transport is the trolleybus. Based on a case study of the Polish cities of Gdynia and Sopot, this paper explores the factors that influence the development of the trolleybus system. Recent developments of in-motion charging (IMC) technology are analysed what provides a new analytical framework for the...
-
Opportunities and challenges for exploiting drones in agile manufacturing systems
PublikacjaDrones have become an advanced supply chain implementation instrument, especially in connecting warehouses to outlet points or even individual customers. However, their potential application in an intra-logistics framework has not been studied, let alone explored so far. Modeling and simulations in virtual environments can help explore and evaluate the opportunities for practical and profitable applications of drones in manufacturing...
-
Down-Sampling of Large LiDAR Dataset in the Context of Off-Road Objects Extraction
PublikacjaNowadays, LiDAR (Light Detection and Ranging) is used in many fields, such as transportation. Thanks to the recent technological improvements, the current generation of LiDAR mapping instruments available on the market allows to acquire up to millions of three-dimensional (3D) points per second. On the one hand, such improvements allowed the development of LiDAR-based systems with increased productivity, enabling the quick acquisition...