Filtry
wszystkich: 1196
wybranych: 1016
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: TECHNICAL REQUIREMENTS AND OPERATING RANGE OF PHOTOVOLTAIC POWER PLANTS
-
ASSESSING THE POTENTIAL REPLACEMENT OF MINERAL OIL WITH ENVIRONMENTALLY ACCEPTABLE LUBRICANTS IN A STERN TUBE BEARING: AN EXPERIMENTAL ANALYSIS OF BEARING PERFORMANCE
PublikacjaT his study compares the performance of a plain bearing, with a similar structure to a tail shaft stern bearing, lubricated with either mineral oil or an environmentally acceptable lubricant (EAL). The main characteristic of the bearing is its length/diameter ratio of <1. Measurements are carried out with the bearing operating under loads from 0.5 to 1 MPa and seven speeds ranging from 1 to 11 rev/s. The bearing lubricated...
-
Optimization of the Relative Humidity of Reactant Gases in Hydrogen Fuel Cells Using Dynamic Impedance Measurements
PublikacjaWater management is a key factor affecting the efficiency of proton exchange membrane fuel cells (PEMFCs). The currently used monitoring methods of PEMFCs provide limited information about which processes or components that humidity has a significant impact upon. Herein, we propose the use of a novel approach of impedance measurements using a multi-sinusoidal perturbation signal, which enables impedance measurements under dynamic...
-
Thermal efficiency investigations on the self-ignition test engine fed with marine low sulfur diesel fuels
PublikacjaWithin the article an issues of implementing the new kinds of marine diesel fuels into ships’ operation was described taking into ac-count restrictions on the permissible sulphur content introduced by the International Maritime Organization. This is a new situation for ship owners and fuel producers, which forces the necessity to carry out laboratory research tests on especially adapted engine stands. How to elaborate the method...
-
Large hydrodynamic thrust bearing: Comparison of the calculations and measurements
PublikacjaHydrodynamic thrust bearings, used to carry axial loads in heavily loaded shafts of water power plants hydro turbines, can reach outer diameters even exceeding 5 m. In such large objects scale effect could be observed. According to this, allowable bearing specific load assuring safe operation of the bearings has to be decreased, which increases thrust bearing dimensions. This effect is caused by excessive thermal deflections of...
-
Deep Eutectic Solvents: Properties and Applications in CO2 Separation
PublikacjaNowadays, many researchers are focused on finding a solution to the problem of global warming. Carbon dioxide is considered to be responsible for the “greenhouse” effect. The largest global emission of industrial CO2 comes from fossil fuel combustion, which makes power plants the perfect point source targets for immediate CO2 emission reductions. A state-of-the-art method for capturing carbon dioxide is chemical absorption using...
-
Integrated plant-wide modelling for evaluation of the energy balance and greenhouse gas footprint in large wastewater treatment plants
PublikacjaModern wastewater treatment plants (WWTPs) should maintain a balance between three combined sustainability criteria, including effluent quality, energy performance and greenhouse gas (GHG) emissions. All of these criteria were considered in the integrated plant-wide model developed in this study. The proposed model incorporates new features, including: (i) the addition of associated facilities to the overall energy balance and...
-
Updating a hospital building. A task for innovation design
PublikacjaRefurbishment of a hospital, especially located in a historical building, is a task that goes far beyond a standard framework of architectural practice. A concept of modularity in the architecture of the late nineteenth and early twentieth century was only just to happen, building system installations and technical equipment appeared as the simplest solutions. Inscribing complex functional solutions into such a space is an interesting...
-
Problemy zarządzania bezpieczeństwem obiektu przemysłowego podwyższonego ryzyka
PublikacjaW rozdziale przedstawiono wybrane zagadnienia dotyczące zarządzania bezpieczeństwem w zautomatyzowanym złożonym obiekcie podwyższonego ryzyka. Pokazano, że ryzyko strat można istotnie ograniczyć stosując odpowiednie rozwiązania techniczne w postaci warstwowego systemu zabezpieczeń, który obejmuje podstawowy system sterowania procesem, człowieka-operatora i system automatyki zabezpieczeniowej. Podkreślono znaczenie właściwego zaprojektowania...
-
A comprehensive overview of software product management challenges
PublikacjaThe principal focus of software product management is to ensure the economic success of the product, which means to prolong the product life as much as possible with modest expenditures to maximizs profits. Software product managers play an important role in the software development organization while being responsible for the strategy, business case, product roadmap, high-level requirements, product deployment (release-management),...
-
Symbiosis of Art and Technology – From Renaissance to Interactive Art,
PublikacjaThe article presents the mutual relations between art and technology from the Renaissance to the interactive art of today. It indicates important factors influencing the possibilities of imaging and interpreting reality by artists, ranging from the development of oil painting techniques, linear perspective, the invention of printing and photography, to achievements related to the development of information technologies (computers,...
-
Potentials of Water Usage in urban Neighbourhood Structures
PublikacjaThis paper will treat about water influence and possibility of its usage in the urban neighborhood structures (e.g. districts, real estate properties, town parts) in the context of actual regional environmental problems and according to directories determined by European targets. It is not rare yet in the basic stage of urban design that water is treated as a threat, not a chance. In result planned structures are often built,...
-
Comparative analysis of three‐phase dual active bridge converter with different transformer topology and modern universal control for DC microgrids
PublikacjaThe presented work discusses issues related to the use of modern multiphase topologies of Dual Active Bridge (DAB)-type converters. Converters of this type are widely used in most DC microgrid applications. The introduction emphasizes a comparative analysis between single-phase and multi-phase DAB topologies within high-power DC microgrids, delving into their respective advantages, drawbacks, design procedures, and considerations...
-
Design and Optimization of Metamaterial-Based 5G Millimeter Wave Antenna for Gain Enhancement
PublikacjaIn this brief, a low profile, broadband, high-gain antenna array based on optimized metamaterials (MMs) with dual-beam radiation is reported for 5G millimeters wave (mm-wave) applications. The design is a simple bow tie operating at a 5G band of 28 GHz. It consists of two bow ties with substrate integrated waveguide (SIW)-based power splitter. A broad impedance bandwidth of 26.3−29.8 GHz is obtained by appropriately combining the...
-
Low-cost data-driven modelling of microwave components using domain confinement and PCA-based dimensionality reduction
PublikacjaFast data-driven surrogate models can be employed as replacements of computationally demanding full-wave electromagnetic simulations to facilitate the microwave design procedures. Unfortunately, practical application of surrogate modelling is often hindered by the curse of dimensionality and/or considerable nonlinearity of the component characteristics. This paper proposes a simple yet reliable approach to cost-efficient modelling...
-
Dobór rodzaju funkcjonalnego PG asfaltów według metody Superpave w zależności od stref klimatycznych w Polsce.
PublikacjaObecnie w Polsce, podobnie jak i w pozostałych krajach Unii Europejskiej, asfalty drogowe są badane i klasyfikowane głównie w oparciu o wynik oznaczenia penetracji w temperaturze 25ºC niezależnie od warunków klimatycznych, w jakich potem mają one pracować w nawierzchni drogowej. Pod koniec ubiegłego wieku w ramach amerykańskiego programu SHRP opracowano i wdrożono nowy system klasyfikacji asfaltów. Ideą wprowadzenia nowego systemu...
-
Accuracy of a low-cost autonomous hexacopter platforms navigation module for a photogrammetric and environmental measurements
PublikacjaA photogrammetry and environmental measurements from an unmanned aerial vehicle (UAV) are a low-cost alternative for a traditional aerial photogrammetry. A commercial off-the-shelf products (COTS) offers a variety of cheap components that a suitable to be used on board a UAV. In this paper a low-cost navigation module based on Ublox NEO-M8N GPS and Pixhawk flight controller have been described, as a main extrinsic parameters source...
-
A modern solid waste management strategy – the generation of new by-products
PublikacjaTo benefit the environment and society, EU legislation has introduced a ‘zero waste’ strategy, in which waste material should be converted to resources. Such legislation is supported by the solid waste hierarchy concept, which is a set of priorities in waste management. Under this concept, municipal solid waste plants (MSWPs) should be equipped with sorting and recycling facilities, composting/incineration units and landfill prisms...
-
Selection of circuit geometry for miniaturized microwave components based on concurrent optimization of performance and layout area
PublikacjaThe paper presents a framework for automated EM-driven circuit geometry selection of miniaturized microwave components. Selection of a particular layout is based directly on miniaturization rates achieved for a set of candidate circuit geometries. Size reduction of the considered structures is obtained by replacing their main building blocks (i.e., conventional transmission lines) with slow-wave composite cells and meander lines....
-
Blue-berried honeysuckle a promising cancer preventing fruit; Polish genotypes as a source of bioactive phytochemicals
PublikacjaFrom the ancient times, plants containing health-oriented compounds in their matrices are used in the treatment of different complaints and diseases. One of these groups are plant secondary metabolites (PSM), especially phenolic compounds, terpenes and terpenoids. A large number of PSM exhibit cytotoxicity against a variety of tumor cells, as well as cancer preventive and anticancer efficacy in preclinical animal models. For this...
-
Myrosinase activity in different plant samples; optimisation of measurement conditions for spectrophotometric and pH-stat methods
PublikacjaMyrosinase found in Brassicaceae plants, is the enzyme responsible for hydrolysis of glucosinolates. As a result a variety of biologically active metabolites are liberated, whose importance in crop protection and especially in cancer chemoprevention is rapidly gaining recognition. The growing practical application of glucosinolate degradation products requires that sensitive and reliable methods of myrosinase activity determination...
-
Refinement of the Hardening Soil model within the small strain range
PublikacjaThe popularity of the elasto-plastic Hardening Soil (HS) model is based on simple parameter identification from standard testing and empirical formulas. The HS model is implemented in many commercial FE codes designed to analyse geotechnical problems. In its basic version, the stress–strain behaviour within the elastic range is subject to the hypoelastic power law, which assures the barotropy of the elastic stiffness. However,...
-
Multi-Criteria Approach in Multifunctional Building Design Process
PublikacjaThe paper presents new approach in multifunctional building design process. Publication defines problems related to the design of complex multifunctional buildings. Currently, contemporary urban areas are characterized by very intensive use of space. Today, buildings are being built bigger and contain more diverse functions to meet the needs of a large number of users in one capacity. The trends show the need for recognition of...
-
Computationally-Efficient Statistical Design and Yield Optimization of Resonator-Based Notch Filters Using Feature-Based Surrogates
PublikacjaModern microwave devices are designed to fulfill stringent requirements pertaining to electrical performance, which requires, among others, a meticulous tuning of their geometry parameters. When moving up in frequency, physical dimensions of passive microwave circuits become smaller, making the system performance increasingly susceptible to manufacturing tolerances. In particular, inherent inaccuracy of fabrication processes affect...
-
Nested Kriging with Variable Domain Thickness for Rapid Surrogate Modeling and Design Optimization of Antennas
PublikacjaDesign of modern antennas faces numerous difficulties, partially rooted in stringent specifications imposed on both electrical and field characteristics, demands concerning various functionalities (circular polarization, pattern diversity, band-notch operation), but also constraints imposed upon the physical size of the radiators. Conducting the design process at the level of full-wave electromagnetic (EM) simulations, otherwise...
-
Increased Certification of Semi-device Independent Random Numbers using Many Inputs and More Postprocessing
PublikacjaQuantum communication with systems of dimension larger than two provides advantages in information processing tasks. Examples include higher rates of key distribution and random number generation. The main disadvantage of using such multi-dimensional quantum systems is the increased complexity of the experimental setup. Here, we analyze a not-so-obvious problem: the relation between randomness certification and computational requirements...
-
A Method of Fast and Simultaneous Calibration of Many Mobile FMCW Radars Operating in a Network Anti-Drone System
PublikacjaA market for small drones is developing very fast. They are used for leisure activities and exploited in commercial applications. However, there is a growing concern for accidental or even criminal misuses of these platforms. Dangerous incidents with drones are appearing more often, and have caused many institutions to start thinking about anti-drone solutions. There are many cases when building stationary systems seems to be aimless...
-
A Microwave Sensor with Operating Band Selection to Detect Rotation and Proximity in the Rapid Prototyping Industry
PublikacjaThis paper presents a novel sensor for detecting and measuring angular rotation and proximity, intended for rapid prototyping machines. The sensor is based on a complementary split-ring resonator (CSRR) driven by a conductor-backed coplanar waveguide. The sensor has a planar topology, which makes it simple and cost-effective to produce and accurate in measuring both physical quantities. The sensor has two components, a rotor, and...
-
Comparison of heat transfer characteristics in surface cooling using microjets with water, ethanol and HFE7100 as test fluids
PublikacjaAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the dimensions of the size of nozzle leads to an increase in the economy of cooling and improves its quality. Present study describes research related to the design and construction of the nozzles and microjet study, which may be applied in many technical applications such as in metallurgy, electronics, etc....
-
An experimental investigation on the effect of new continuous core-baffle geometry on the mixed convection heat transfer in shell and coil heat exchanger
PublikacjaIn the article, the authors presented the influence of continuous core-baffle geometry at mixed convection heat transfer in shell and coil heat exchanger. Experiments were carried out for a large power range, i.e. from 100W to 1200W and mass flow rates ranging from 0.01 kg/s to 0.025 kg/s. During the experiments, the mass flow rate of cooling water, the temperature of water at the inlet and outlet as well as the wall temperature...
-
Method of earth fault loop impedance measurement without nuisance tripping of RCDs in 3-phase low-voltage circuits
PublikacjaVerification of electrical safety in low-voltage power systems includes the measurement of earth fault loop impedance. This measurement is performed to verify the effectiveness of protection against indirect contact. The widespread classic methods and meters use a relatively high value of the measuring current (5–20) A, so that they are a source of nuisance tripping of residual current devices (RCDs). The meters dedicated to circuits...
-
The development of an underwater telephone for digital communication purposes
PublikacjaThe underwater telephone HTL-10 has been designed to provide voice and data communication between helicopter and submarines using acoustic waves. It works in a half-duplex mode and uses analogue power-efficient modulation in the form of a single side-band, suppressed carrier, in a wide range of frequencies. It generates the transmitted signal, and processes the received signals. It is implemented with the use of digital signal...
-
Numerical study of turbulent flow and heat transfer of nanofluids in pipes
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000 < Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data of Vajjha et al. [1]. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Flicker Noise in Resistive Gas Sensors—Measurement Setups and Applications for Enhanced Gas Sensing
PublikacjaWe discuss the implementation challenges of gas sensing systems based on low-frequency noise measurements on chemoresistive sensors. Resistance fluctuations in various gas sensing materials, in a frequency range typically up to a few kHz, can enhance gas sensing by considering its intensity and the slope of power spectral density. The issues of low-frequency noise measurements in resistive gas sensors, specifically in two-dimensional...
-
Integrated Three-Level Dual-Phase Inverter
PublikacjaIn view of reducing the number of inverter legs that provide dual-phase, three-level output voltages (as may be needed in an uninterruptible power supply), and that also provide a wide range of output frequencies (as needed in an advanced motor drive system with wide speed ranges), a three-level, dual-phase inverter topology is presented in this paper. Its three-level attribute was based on the F-type inverter topological concept,...
-
Technologia medyczna w obiektach świadczących usługi lecznicze- Medical technology in healthcare facilities
PublikacjaArchitektura budynków szpitalnych kreowana jest pod silnym wpływem wymagań sanitarno-higienicznych oraz wytycznych wynikających z charakteru świadczonych usług medycznych. Naczelną rolę odgrywa tu technologia medyczna, która jest zasobem wiedzy, procesów organizacyjnych i środków fizycznych uczestniczących w realizacji zdefiniowanych świadczeń zdrowotnych. Istotnym elementem takiej kreacji architektonicznej jest szereg procesów...
-
Multicriteria Optimization Approach to Design and Operation of District Heating Supply System over its Life Cycle
PublikacjaDistrict Heating (DH) systems are commonly supplied using local heat sources. Nowadays, modern insulation materials allow for effective and economically viable heat transportation over long distances (over 20 km). In the paper a method for optimized selection of design and operating parameters of long distance Heat Transportation System (HTS) is proposed. The method allows for evaluation of feasibility and effectivity of heat transportation...
-
Extremal thermal loading of a bifurcation pipe
PublikacjaThe subject of considerations is a spherical bifurcation pipe of a live steam made of steel P91, which is an element of a block of coal-fired power plant working with a 18K370 turbine. As experience shows, it is a very sensitive element of the boiler pipelines. An extreme work scenario for such a block has been adopted, in which the turbine is shutting down to a warm state three times in 24 hours. This is an action dictated by...
-
Design of a Shape-Memory-Alloy-Based Carangiform Robotic Fishtail with Improved Forward Thrust
PublikacjaShape memory alloys (SMAs) have become the most common choice for the development of mini- and micro-type soft bio-inspired robots due to their high power-to-weight ratio, ability to be installed and operated in limited space, silent and vibration-free operation, biocompatibility, and corrosion resistance properties. Moreover, SMA spring-type actuators are used for developing different continuum robots, exhibiting high degrees...
-
Behaviour of asymmetric structures with base isolation made of Polymeric Bearings
PublikacjaEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Seismic excitations cause a lot of damage in a wide variety of ways, leaving thousands of casualties in their wake. During the last few years alone, the world has witnessed many major earthquakes, five of which have caused far-reaching consequences of a national scale for Haiti (January 2010), Chile (February...
-
Context sensitive privacy management in a distributed environment
PublikacjaArtykuł przedstawia mechanizm zarządzania prywatnością stworzony dla systemu rozproszonego z założeniem, że węzły systemu mają ograniczone zasoby (moc procesora, pamięć). Podstawowy pomysł zakłada, że prywatne dane są filtrowane zgodnie z polityką prywatności użytkowników przed ich ujawnieniem innym użytkownikom. Te decyzje są silnie umiejscowione, co ogranicza narzut związany z zarządzaniem prywatnością na węzłach systemu. Sam...
-
Water-Lubricated Sintered Bronze Journal Bearings—Theoretical and Experimental Research
PublikacjaWater lubricated bearings are used from many years in shipbuilding, hydro power and other industries because of their advantages such as: extensive serviceable life, low coefficient of friction, longevity of shaft sleeve, good abrasion resistance, low maintenance required, unit simplicity, no danger of pollution and low price. Various types of water lubricated sliding bearings have been tested at the Technical University of Gdansk...
-
Hybrid Multi-Criteria Method of Analyzing the Location of Distributed Renewable Energy Sources
PublikacjaThis paper presents the development and the application of a hybrid multi-criteria method, the combination of the Analytic Hierarchy Process (AHP), and numerical taxonomy (NT),to support the decision making on the location of distributed renewable energy sources meetingvarious types of assessment criteria. Finding criteria weights, using the AHP method, eliminates thedisadvantage of NT—which, in current form, is defined by its...
-
Assessment of Supercapacitor’s Quality by Means of Low Frequency Noise
PublikacjaLow frequency noise is a well-known tool for quality and reliability assessment of electronic devices. This phenomenon is observed in different electrochemical devices as well (e.g., smart windows, electrochemical corrosion processes). Thus, we can assume that the same tool can be used to asses quality of supercapacitors. Their quality is usually determined only by capacitance and/or equivalent series resistance (ESR), or impedance....
-
Vascular stents - materials and manufacturing technologies
PublikacjaThe objective of this article is to present materials and technology for the manufacture of vascular stents with appropriate design requirements. The use of the right material is very important in implantology. A biomaterial introduced into the circulatory system must be biocompatible and hemocompatible. At the same time, it should not initiate toxic, mutagenic, or immunological reactions. Currently, 316L stainless steel (316L...
-
DUAL CONSTELLATION GPS/GALILEO MOBILE SYSTEM FOR IMPROVING NAVIGATION OF THE VISUALLY IMPAIRED IN AN URBAN AREA
PublikacjaIt is well known by users of Portable Navigation Device (PND) and other GPS-based devices that positioning suffers from (local) significant decreases of accuracy in partially obscured environments like urbanized areas, where buildings (especially high buildings), trees or terrain block large portions of the sky. In such areas, GPS receiver performance is usually deteriorated by the reduced number of currently available satellite...
-
DESIGN OF THE DUAL CONSTELLATION GPS/GALILEO MOBILE DEVICE FOR IMPROVING NAVIGATION OF THE VISUALLY IMPAIRED IN AN URBAN AREA
PublikacjaIt is well known by users of Personal Navigation Device (PND) and other GPS-based devices that positioning suffers from (local) significant decreases of accuracy in partially obscured environments like urbanized areas, where buildings (especially high buildings), trees or terrain block large portions of the sky. In such areas, GPS receiver performance is usually deteriorated by the reduced number of currently available satellite...
-
Controlling nodal displacement of pantographic structures using matrix condensation and interior-point optimization: A numerical and experimental study
PublikacjaThis study presents an innovative approach for the precise control of nodal displacements in pantographic structures. The method is founded on the Matrix Condensation of Force Method, seamlessly integrated with an Interior Point Optimization algorithm. This combination offers a unique advantage by allowing users to manipulate displaced nodes within a defined coordination domain. Furthermore, this approach introduces the Interior...
-
The effects of different aeration modes on ammonia removal from sludge digester liquors in the nitritation–anammox proces
PublikacjaThe aim of this study was to determine the impact of continuous and intermittent aeration on the rate of ammonia removal in the combined nitritation–anammox process. This process was run in two parallel sequencing batch reactors (SBRs), with a working volume V = 10 L, treating sludge digester liquors from the Gdansk (Poland) wastewater treatment plant (WWTP). The ammonia oxidizing bacteria were cultivated from activated sludge...
-
Shielded HMSIW-based frequency-tunable self-quadruplexing antenna using different solid/liquid dielectrics
PublikacjaThis article proposes a frequency-tunable self-quadruplexing antenna based on a shielded half-mode substrate integrated waveguide (S-HMSIW). In order to reduce the size of the HMSIW cavity resonator and to obtain quad-band characteristics, a modied E-shaped slot is engraved on the top of the metal. The experimental validation is carried out after analyzing the data using a circuit model. Flexibility of each resonant frequency is...
-
Performance tuning of chitosan-based membranes by protonated 2-Pyrrolidone-5-carboxylic acid-sulfolane DES for effective water/ethanol separation by pervaporation
PublikacjaToday, the applicability of deep eutectic solvents (DES) in various fields, including membrane science and technology, is extensively investigated. In pioneering works, we have implemented different DES as a component of chitosan (CS)-based flat membranes for pervaporation (PV) separation. Herein, we present a new protonated (by sulphuric acid) 2-Pyrrolidone-5-carboxylic acid: sulfolane DES, as a green additive for its chemical...