Wyszukiwarka
Filtry
wszystkich: 1948
wybranych: 1196
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: air
-
Model and laboratory simulation of a induction motor for diagnostic purposes
PublikacjaStatistics say that bearings are this part of induction motors which is most susceptible to damage. The equipment employed for bearing diagnostics usually makes use of vibrations as the criterion for technical condition of the bearings. A faulty bearing results in additional motor vibrations. They are reflected in the harmonic content of stator currents. In certain operating conditions the current signal is the sole source of information...
-
Morphology control via dual solvent crystallization for high-mobility functionalized pentacene-blend thin film transistors
PublikacjaWe present an approach to improving the performance of solution processed organic semiconductor transistors based on a dual solvent system. We here apply this to a blend containing the π-conjugated small molecule 6,13 bis(triisopropylsilylethynyl) pentacene (TIPS-pentacene) and polystyrene, which acts as an inert binder. Using a semiconductor-binder solution of two solvents, where the main solvent is a better solvent of the small...
-
Równoważność metod pomiarowych ciągłych i odniesienia stosowanych do oznaczania pm10
PublikacjaW pracy przedstawiono wyniki testu terenowego przeprowadzonego na terenie Gdańska w okresie od 01-01-2010 do 31-12-2010 i od 01-01-2011 do 31-12-2011 w celu wykazania równoważności wskazań analizatora Eberline FH 62-1 w stosunku do wagowej metody odniesienia. Przedyskutowano występowanie różnic wskazań wartości stężeń pyłu PM10 w zależności od pory roku dla obu metod pomiarowych. Przedstawiono sposób określania równoważności tych...
-
Enhancement of fiber-optic low-coherence Fabry-Pérot interferometer with ZnO ALD films
PublikacjaIn this paper investigation of the enhanced fiber-optic low coherence Fabry-Pérot interferometer with zinc oxide (ZnO) film deposited by atomic layer deposition (ALD) was presented. Model of the interferometer, which was constructed of single-mode optical fiber with applied ZnO ALD films, was built. The interferometer was also examined by means of experiment. Measurements were performed for both reflective and transmission modes,...
-
Ag/Pt-modified TiO2 nanoparticles for toluene photooxidation in the gas phase
PublikacjaAg/Pt-modified TiO2nanocomposites were synthesized using the sol–gel method. The effect of metal typeand amount as well as synthesis route on the photocatalytic activity in reaction of toluene removal, usedas a model volatile organic compound, was investigated. Toluene, at the concentration of about 200 ppm,was irradiated over modified TiO2using light-emitting diodes (LEDs, max= 415 nm). The results showedthat toluene could be...
-
Structure and thermoelectric properties of Bi–Te alloys obtained by novel method of oxide substrates reduction
PublikacjaA novel method of thermoelectric materials fabrication has been developed. Oxide reagents have been melted at high temperature in air, quenched, milled to powder and reduced in hydrogen to form Bi–Te alloys. Structural and thermoelectric properties of samples have been investigated depending on initial composition and temperature of reduction process. Sample 25Bi2O3–75TeO2 reduced at 340 °C for 10 h has been found to be a p-type...
-
MARITIME LASER SCANNING AS THE SOURCE FOR SPATIAL DATA
PublikacjaThe rapid development of scanning technology, especially mobile scanning, gives the possibility to collect spatial data coming from maritime measurement platforms and autonomous manned or unmanned vehicles. Presented solution is derived from the mobile scanning. However we should keep in mind that the specificity of laser scanning at sea and processing collected data should be in the form acceptable in Geographical Information...
-
Application of additional factors supporting the microextraction process
PublikacjaDue to the fact that green analytical chemistry is of high importance, the past two decades have witnessed a rapid growth in the sample preparation area with special emphasis on simplification, miniaturization and automation of extraction procedures. In addition, to accelerate the extraction processes and to improve the separation of analytes, several enhanced parameters are applied. These factors include, ultrasounds, microwaves,...
-
The Influence of Stretch Rod Speed on the Relationship between Preblown Bottle Aesthetic Quality and Final Blown Bottle Thickness Profile in Stretch Blow Molding from Preform Process
PublikacjaFrom a mechanical point of view, the aesthetic quality of preblown PET bottles and thickness profile of final blown PET bottles manufactured in ISBM process are determined by mechanical and thermal response of blown preforms. From the microscopic point of view the biggest influence on the mechanical and thermal properties of PET bottles have orientation and crystallization processes. From a technological point of view, the aesthetic...
-
Detection of gaseous compounds with different techniques
PublikacjaSensing technology has been developed for detection of gases in some environmental, industrial, medical, and scientific applications. The main tasks of these works is to enhance performance of gas sensors taking into account their different applicability and scenarios of operation. This paper presents the descriptions, comparison and recent progress in some existing gas sensing technologies. Detailed introduction to optical sensing...
-
Experiment with small objects floating under water in the harbor security aspect.
PublikacjaObservation of the underwater area is the element of general trend which primary purpose is to protect and enhance the safety of the selected region. The aim of the paper is to present the acoustic characteristics of typical objects floating on the surface or under the water, which constitute some knowledge on how to detect these objects. Create a catalog of acoustic signatures and acoustic images of objects mostly floating under...
-
Signals features extraction in radioisotope liquid-gas flow measurements using wavelet analysis
PublikacjaKnowledge of the structure of a flow is significant for the proper conduct of a number of industrial processes. In this case, a description of a two-phase flow regimes is possible by use of the time-series analysis in time, frequency and state-space domain. In this article the Discrete Wavelet Transform (DWT) is applied for analysis of signals obtained for water-air flow using gamma ray absorption. The presented method was illustrated...
-
X-RAY DIFFRACTION STUDY OF BISMUTH LAYER-STRUCTURED MULTIFERROIC CERAMICS
PublikacjaGoal of the present research was to apply a solid state reaction route to fabricate bismuth layer-structured multiferroic ceramics described with the formula Bi5FeTi3O15 and reveal the influence of processing conditions on its crystal structure and phase composition. Simple oxide powders Bi2O3, TiO2 and Fe2O3 were used to fabricate Aurivillius-type bismuth layer-structured ferroelectrics. Pressureless sintering in ambient air was...
-
ANALYSIS OF WIND CONDITIONS AROUND A BUILDING DEVELOPMENT AS A PART OF ITS FORM DESIGNING PROCESS, A CASE STUDY
PublikacjaAerodynamic phenomena that occurs around building developments exert a significant impact on the quality of climate in cities. Environmental wind engineering is a dynamically developing field of knowledge that offers a chance to study and, in consequence, regulates the air flow around buildings and complexes of building developments. The following paper discusses the issue of wind conditions that may be experienced on pedestrian...
-
The effect of morphology and crystalline structure of Mo/MoO3 layers on photocatalytic degradation of water organic pollutants
PublikacjaMolybdenum oxide layers were formed by anodization of the Mo metallic foil in a water/ethylene glycol-based electrolyte containing fluoride ions. The as-prepared, amorphous samples were annealed in air at different temperatures in a range from 100 �C to 700 �C. The crystal phase and morphology of anodized and annealed MoO3 layers were investigated using X-ray diffraction, Raman spectroscopy, and scanning electron microscopy. The...
-
Design of poroelastic wearing course with the use of direct shear test
PublikacjaPoroelastic Road Surfaces (PERS) are characterized by porous structure with at least 20% of air void content and stiffness almost 10 times lower than typical asphalt course. Such properties enable noise reduction up to 12 dB in comparison to SMA 11 mixture. However, the main disadvantage of previously used poroelastic mixtures, based on resin type binders, was their low durability, which resulted in raveling and delamination from...
-
The process generation of WWTP models for optimization of activated sludge systems
PublikacjaThe objective of water and wastewater utilities, which are responsible for optimization of wastewater treatment plant operation, is threefold: environmental protection, saving money, and mitigation of pollutant emissions, both to water and air. The performed study aimed to assess the process generation of WWTP models that improve activated sludge systems operation, by means of new developed Mantis2 model. This model accounts for...
-
Spectral reflectance and transmission modeling of multi-cavity Fabry-Pérot interferometer with ZnO thin films
PublikacjaIn this paper spectral reflectance and transmission of a low-coherence fiber-optic Fabry-Pérot interferometer with thin ZnO layers is analyzed using a multi-cavity approach. In the investigated setup two standard single-mode optical fibers (SMF-28) with thin ZnO films deposited on their end-faces form an extrinsic Fabry-Pérot interferometer with air cavity. Calculations of the spectral response of the interferometer were performed...
-
The low coherence Fabry-Pérot interferometer with diamond and ZnO layers
PublikacjaThe authors present a fiber-optic Fabry-Pérot interferometer built with the application of diamond and zinc oxide (ZnO) thin layers. Thin ZnO films were deposited on the tip of a standard telecommunication single-mode optical fiber (SMF- 28) while the diamond layer was grown on the plate of silicon substrate. Investigated ZnO layers were fabricated by atomic layer deposition (ALD) and the diamond films were deposited using Microwave...
-
Temperature Sensors Based on Polymer Fiber Optic Interferometer
PublikacjaTemperature measurements are of great importance in many fields of human activities, including industry, technology, and science. For example, obtaining a certain temperature value or a sudden change in it can be the primary control marker of a chemical process. Fiber optic sensors have remarkable properties giving a broad range of applications. They enable continuous real-time temperature control in difficult-to-reach areas, in...
-
Influence of cyclic frozen and defrost on mechanical properties of polytetrafluoroethylene (PTFE)-coated woven fabrics
PublikacjaThis research aims to determine the influence of the cyclic process of freezing and defrosting on the mechanical properties of the chosen glass fibres and PTFE-coated woven fabrics. The specimens were subjected to freezing at about −20 °C for 4 h and thawing by full immersion into the water at about +20 °C for 4 h. The fabric samples after 25 and 50 frozen cycles were air-dried at room temperature for one week and then subjected...
-
The Influence of Thin Gold Electrodes on the High-Temperature Impedance of Oxide Glasses
PublikacjaThe influence of thin gold electrodes on the electrical measurements of glasses at high temperatures was studied using impedance spectroscopy. The impedance was measured several times over a wide frequency range from 10 mHz to 1 MHz and the temperature ranged from 213 to 673 K under air and nitrogen atmospheres. The results showed a drop in the conductivity of more than an order of magnitude at a temperature around 603 K during...
-
Models of Brushless Synchronous Generator for Studying Autonomous Electrical Power System
PublikacjaThis is a PhD dissertation. The work presented in this monograph was carried out at the Department of Power Electronics and Electrical Machines, Faculty of Electrical and Control Engineering at the Gdansk University of Technology. Developed during the research models of brushless synchronous generator ware verified using FEM based simulations and measurements conducted on the prototype generator. The main focus of the research...
-
Thermochemical Conversion of Biomass and Municipal Waste into Useful Energy Using Advanced HiTAG/HiTSG Technology
PublikacjaAn advanced thermal conversion system involving high-temperature gasification of biomass and municipal waste into biofuel, syngas or hydrogen-rich gas is presented in this paper. The decomposition of solid biomass and wastes by gasification is carried out experimentally with a modern and innovative regenerator and updraft continuous gasifier, among others. A ceramic high-cycle regenerator provides extra energy for the thermal conversion...
-
The effect of 1,4-butanediol on the efficiency of CO2 absorption and inhibition of NH3 escape during the mineral carbonation of gypsum
PublikacjaThis study explored the optimal concentration of 1,4-butanediol for maximizing CO2 absorption and minimizing ammonia desorption. Mineral carbonation of gypsum slurry was carried out in a bubble reactor with a magnetic stirrer maintaining constant speed for 1 hour. The gas introduced to the reactor was a mixture of CO2 and air. The gas flow was controlled by the mass controllers. Gas sensors were used to determine the concentration...
-
Reactivity of bulky aminophosphanes towards small molecules: Activation of dihydrogen and carbon dioxide by aminophosphane/borane frustrated Lewis pairs
PublikacjaA series of mono- and bisaminophosphanes with formulas R2NPR’R’’ and (R2N)2PR’ (R = iPr, Cy; R’ = Ph, Cy; R’’ = iPr) were characterized by X-ray analysis, NMR spectroscopy and computational methods. The common structural futures of these species are short and polarized PAN bonds, a pyramidal geometry at the P atom and an almost planar geometry at the N atoms. According to DFT calculations, these...
-
Monetary values estimates of solvents emissions
PublikacjaThe impact values for environmental emissions of 52 solvents are estimated and expressed in monetary units. The impact values of solvents present in the air are calculated on the basis of 13 impact indicators and for solvents present in water on additional 2 impact indicators. These impact values are weighted with the results obtained with multi-compartment distribution model, allowing to calculate the fraction of solvent emitted...
-
Influence of High Temperature Oxidation on Hydrogen Absorption and Degradation of Zircaloy-2 and Zr 700 Alloys
PublikacjaThe present research was aimed at determining the effects of the oxide layers on hydrogen absorption, microstructure and mechanical properties of the Zircaloy- 2 and Zr 702 alloys. The oxidation was made at 350 °C, 700 °C and 900 °C for 10 to 30 min in laboratory air, followed by hydrogen cathodic charging for 72 h and annealing at 400 °C for 4 h. The slow strain rate tests were carried out on oxidized, charged and annealed specimens. The...
-
Conversion of Biomass and Municipal Wastes into Syngas and Hydrogen using Highly Preheated Agent (HTAG)
PublikacjaGasification is considered to be one of the most promising energy recovery technologies for the widespread utilization of biomass and wastes. During this process raw feedstock is converted into a combustible gas, which can then be burnt to produce thermal energy, or to run engines for mechanical or electrical power. The studies of biomass gasification demonstrate it as a friendly alternative to fossil fuels as one of renewable...
-
Experimental investigation on straight and u-bend double tube heat exchanger with active and passive enhancement methods
PublikacjaAuthors in this work want to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. In the study, Wilson plot approach was applied in order to estimate heat transfer coefficients for all heat exchanger (HX) configurations. The study focuses on experimental values of heat transfer coefficient...
-
Odour Perception Using a Sniffing Team at a Municipal Solid Waste Treatment Plant: A Case Study
PublikacjaThe monitoring of odour intensity, generated by a landfill area, is a difficult activity since it is a multi-source problem with discontinuous odour emissions. A modified sniffing team method is described here and applied to determine the main odour sources in a landfill located in Pomerania, Poland. Four consecutive test sessions were performed during the following months: August, December, April, and June. It was found that the...
-
O problemie kolmatacji geowłóknin stosowanych w drenażach
PublikacjaSystemy drenażowe występujące przy obiektach drogowych są niezwykle istotnym elementem tych budowli. Jednym z materiałów, które obecnie powszechnie stosowane są w systemach drenażowych są geowłókniny. Ich zadaniem jest zabezpieczenie odwadnianego gruntu przed procesem sufozji, jak również ochrona drenażu przed zamuleniem przy jednoczesnym zachowaniu wodoprzepuszczalności. Typową trwałość drenażu, w zależności od rozwiązań, szacować...
-
Dynamics of fault arc traveling along busbars in high voltage switchboards = Dynamika łuku zwarciowego przemieszczającego się wzdłuż szyn rozdziel-nic wysokiego napięcia
PublikacjaThe paper presents the results of magnetic induction and electrodynamic force calculations acting on arc column during short-circuit in medium voltage air-insulated bus-bars. The gap between the bars was 120 mm and the prospective short-circuit currents ranged from 4 kA to 8 kA. The paper also shows the measurement results of average velocity fault arc depending on currents arc diameter and arc current was established and described....
-
Wpływ emisji Lotnych Związków Organicznych (LZO), na jakość powietrza w pomieszczeniach wnętrz
PublikacjaNa jakość powietrza w pomieszczeniach wnętrz (ang. Indoor Air Quality, IAQ) mają wpływ zarówno czynniki fizyczne (np. hałas, temperatura, wilgotność powietrza) jak i czynniki chemiczne (m.in. Lotne Związki Organiczne, LZO) oraz biologiczne (np. mikroorganizmy). W przypadku czynników chemicznych, istotną grupę związków stanowią głównie LZO (np. węglowodory aromatyczne, alifatyczne). Ponad połowa emisji tych związków pochodzi z materiałów...
-
Sensorless Control of Polyphase Induction Machines
PublikacjaThe basics of transformations of polyphase systems into orthogonal systems are explained. Vector models of induction machines in orthogonal planes are analysed and multiscalar models for rotor flux and main flux together with stator current are presented. A speed observer based on an extended model of the induction machine for selected variables is applied in the control system for the induction machine. On the basis of the model...
-
Properties of Thermally Dewetted Thin Au Films on ITO-Coated Glass for Biosensing Applications
PublikacjaNoble metal nanostructures are object of great interest due to their unique optical and electronic properties exploited in nanotechnology, medicine, biochemistry, and surface-enhanced spectroscopies. In this work, the Au nanoparticle (NP) structures for application in biosensing obtained by dewetting are investigated in dependence on their preparation conditions. Structures are produced from thin Au films (5–30 nm) sputtered onto...
-
Sposoby zagospodarowania ciepła odpadowego z silników napędowych jednostek pływających Cześć 1. Wykorzystanie ciepła do napędu urządzeń chłodniczych
PublikacjaEnergia chemiczna paliwa jest w wielu przypadkach zaledwie w połowie wykorzystana jako energia napędowa silnika. Pozostała część jako ciepło odpadowe przekazywana jest do otoczenia. Dzięki odpowiednim układom przetwarzania ciepło ze spalin można wykorzystać do wytwarzania chłodu lub jako ciepło użytkowe, w systemach HVAC (ang. heating, ventilation, air conditioning – ogrzewanie, wentylacja, klimatyzacja). Tym samym koszty pracy...
-
Study of Cloud Water Samples Collected over Northern Poland
PublikacjaThe paper gives the results of the first studies on the chemistry of cloud water collected during 3 mo (Aug.–Oct. 2010) in the free atmosphere over the area to the south of the Tri-City (Gdansk-Sopot-Gdynia) conurbation on the Gulf of Gdansk, Poland. Taken from cumulus, stratus, and stratocumulus clouds by means of an aircraft-mounted collector, the water samples were analyzed for the following contaminants: anions (chlorides,...
-
Electrochemical Activity and Electrical Properties of Optimized Polypyrrole Coatings on Iron
PublikacjaIn this work, electrochemical activity and electrical properties of polypyrrole (PPy) coated iron electrodes have been investigated. PPy film was electrochemically polymerized from sodium salicylate aqueous solution under conditions, which provided an increase of iron corrosion resistance. It was noticed that the pH of the solution and the applied electrode potential range during the study of the polymer properties had an influence...
-
Methodology for determination of the selected mechanical properties of wood based on cutting tests
PublikacjaFrom kiln-dried spruce wood (with steam) as well as in natural conditions were randomly selected 8 samples. After determining the average dimensions, moisture content and density of the samples they have been cut on the frame sawing machine PRW15M for measurement of cutting power. Based on those results from a linear rela-tionship of cutting power versus feed per toot mechanical properties of wood such as facture toughness and...
-
Effect of underwater wet welding conditions on the diffusible hydrogen content in deposited metal
PublikacjaIn the study mercury displacement method was used for determination of diffusible hydrogen amount in deposited metal obtained during underwater wet welding with covered electrodes in laboratory conditions according to a two-level full factorial design for three factors. The factors and their levels were chosen among conditions and parameters of welding in accordance with the results of own preliminary studies. A statistical analysis...
-
Investigation of Narrow Electrostatic Precipitator with Wire Multi-Electrode
PublikacjaDiesel engines emit fine particles, which are harmful to human and animal health. There are several methods for decrease particulate emission from a diesel engines, but up to now, these methods are notenough effective or very expensive. An electrostatic precipitation was proposed as an alternative method for control of a diesel particulate emission. Therefore, narrow electrostatic precipitators (ESPs) have become a subject of interest...
-
Supervisory Control System for Adaptive Phase and Work Cycle Management of Sequencing Wastewater Treatment Plant
PublikacjaThe paper presents the design of the integrated control system applied to Sequencing Batch Reactor (SBR) in a biological Wastewater Treatment Plant (WWTP) in Swarzewo, which operates under activated sludge technology. Based on the real data records, ASM2d biological processes model and aeration system model, hierarchical control system for dissolved oxygen tracking and cycle management is designed. Internal Model Controller (IMC)...
-
Application of Thin ZnO ALD Layers in Fiber-Optic Fabry-Pérot Sensing Interferometers
PublikacjaIn this paper we investigated the response of a fiber-optic Fabry-Pérot sensing interferometer with thin ZnO layers deposited on the end faces of the optical fibers forming the cavity. Standard telecommunication single-mode optical fiber (SMF-28) segments were used with the thin ZnO layers deposited by Atomic Layer Deposition (ALD). Measurements were performed with the interferometer illuminated by two broadband sources operating...
-
Two-Level Multivariable Control System of Dissolved Oxygen Tracking and Aeration System for Activated Sludge Processes
PublikacjaThe problem of tracking dissolved oxygen is one of the most complex and fundamental issues related to biological processes. The dissolved oxygen level in aerobic tanks has significant influence on behaviour and activity of microorganism inhabiting the plant. Aerated tanks are supplied with air from an aeration system (blowers, pipes, throttling valves, diffusers). It is a complex dynamic system governed by nonlinear hybrid dynamics....
-
Coplanar Waveguide-Fed Broadband Microwave Devices with (or without) a Thin Dielectric Substrate for Use in Flexible Electronic Systems
PublikacjaTwo examples of microwave devices, fed by a coplanar waveguide and realized on a thin substrate (or without such a substrate), are employed to investigate the influence of devices’ curvatures and the proximity of different materials on their parameters. To perform the tests, a broadband antenna and a low-pass filter are chosen. A feeding coplanar waveguide is realized on a dielectric material brick attached to an SMA connector...
-
EFFICIENCY OF GAS MIXTURES DETECTION BY RESISTIVE GAS SENSORS
PublikacjaResistive gas sensors are very popular and are commonly used to detect various gases and their mixtures. Their main disadvantage is very limited selectivity. Practical use of gas sensors in environmental applications (e.g., in sewage systems to protect workers, in air conditioning systems to monitor atmosphere quality) requires determination of concentration of a few mixed gases at the same time. We would like to present recent...
-
Assessment of under power ed propulsion machinery in electrically driven small inland waterway passenger ships from classification society point of view
PublikacjaPaper presents short operat ional a nd engineering analysis of underpowered propulsion in small electrically propelled small inland passenger ships. There is evidence that in certain weather conditions the phenomena of added aerodynamic resistance of small water crafts may have seriou s influence on their speed and manoeuvrability. Existing regulations like class societies rules for ship classification and construction or EU Directive 2006/87/EC do...
-
ASSESSMENT OF UNDERPOWER ED PROPULSION MACHINERY IN ELECTRICALLY DRIVEN SMALL INLAND WATERWAY PASSENGER SHIPS FROM CLASSIFICATION SOCIETY POINT OF View
PublikacjaPaper presents short operat ional a nd engineering analysis of underpowered propulsion in small electrically propelled small inland passenger ships. There is evidence that in certain weather conditions the phenomena of added aerodynamic resistance of small water crafts may have serious influence on their speed and manoeuvrability. Existing regulations like class societies rules for ship classification and construction or EU Directive 2006/87/EC do...
-
Performance of microbial fuel cells operated under anoxic conditions
PublikacjaNowadays, microbial fuel cells (MFC) stand up as a promising renewable energy source. Due to the ability of the MFC to oxidize a wide spectrum of substrates, wastewater seems to be one of the most interesting fuels. Unfortunately, wastewater could contain electron acceptors such as nitrate, which could interfere with the electrical performance of the MFC. In this work, the influence of oxidised nitrogen forms on the electricity...