Filtry
wszystkich: 1731
wybranych: 1403
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: COMBUSTION ENGINE TESTING
-
Example of Using Particle Swarm Optimization Algorithm with Nelder–Mead Method for Flow Improvement in Axial Last Stage of Gas–Steam Turbine
PublikacjaThis article focuses principally on the comparison baseline and the optimized flow efficiency of the final stage of an axial turbine operating on a gas–steam mixture by applying a hybrid Nelder– Mead and the particle swarm optimization method. Optimization algorithms are combined with CFD calculations to determine the flowpaths and thermodynamic parameters. The working fluid in this study is a mixture of steam and gas produced...
-
Pyrolysis and Torrefaction—Thermal Treatment of Creosote-Impregnated Railroad Ties as a Method of Utilization
PublikacjaA fundamental issue of waste management and the rail transport industry is the problem of utilizing used railroad ties. Wooden railroad ties are treated with a preservative, usually creosote. Due to their high toxicity, railroad ties are considered hazardous waste and must be utilized under various directives. It is proposed to utilize the troublesome waste by using the pyrolysis and torrefaction process. The research proves that...
-
Elementary analysis and energetic potential of the municipal sewage sludges from the Gdańsk and Kościerzyna WWTPs
PublikacjaThis paper aims to present municipal sewage sludge (MSS) elementary analysis and energetic potential based on measurement of heat of combustion (higher heating value HHV) and calculation of calorific values (lower heating value LHV). The analysis takes into the consideration water content in sewage sludge, at different utilization stages, in wastewater treatment plants in Gdańsk Wschód and Kościerzyna – Pomeranian Voivodeship....
-
Proposal of a mobile medical waste incinerator with automatic waste feeder and heat recovery system
PublikacjaThe paper presents and discusses the issue of medical waste (including hazardous ones) and their proper management. Inappropriate handling of infectious medical waste directly endangers the human being health and the environment. Infectious waste must therefore be properly disposed of – one of the most commonly used methods is the thermal treatment in the incinerators tailored for this purpose. During designing an incinerator unit,...
-
Proposal of a Mobile Medical Waste Incinerator with Application of Automatic Waste Feeder and Heat Recovery System as a Novelty in Poland
PublikacjaThe paper presents and discusses the issues of medical waste (including hazardous ones) and the problems regarding their proper management in Poland. Inappropriate handling of infectious medical waste directly endangers human health and the environment. Infectious waste must be properly disposed of—in practice, the only method of their disposal available in Poland is a thermal treatment in the incinerators tailored for this purpose....
-
MCSA with Normalized Triple Covariance as a bearings diagnostic indicator in an induction motor
PublikacjaStatistics of bearing failures in induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is very important. Vibration methods for bearing diagnostics have one major disadvantage - they require the availability of the machine for sensors installation. This is the reason for seeking new methods based on motor supply current analysis. Diagnosis of induction motors, conducted remotely...
-
The conception of energetic investigations of the multisymptom fatigue of the simple mechanical systems' constructional materials
PublikacjaThe article presents the basic assumptions of the research project aimed, as the main scientific purpose, an identification of the slow-changeable energy processes surrounding the high-cycle fatigue of constructional materials within the plain mechanical system, especially the marine one, for diagnostic purposes. There is foreseen an application of alternative diagnostic methods based on energetic observations of the multi-symptom,...
-
COMPOSITE FOOTBRIDGE - SYNERGY EFFECT IN COOPERATION BETWEEN UNIVERSITIES AND INDUSTRY
PublikacjaPaper presents conditions of science and industry cooperation in Poland (restrictions, barriers, good practice). A key role in initiation of collaboration between units has financial support. What is also important, it is much easier to create innovative solutions on the base of combining the potential of individuals. That is why many countries all over the world look for innovative solutions using budget funds to support grants...
-
Projektowanie gier komputerowych z wykorzystaniem Unreal Development Kit
PublikacjaW pracy przedstawiono pakiet narzędziowy Unreal Development Kit (UDK) umożliwiający tworzenie gier w oparciu o silnik Unreal Engine 3 (UE3). Silnik ten umożliwia tworzenie wieloplatformowych, zaawansowanych graficznie gier praktycznie dowolnego typu. UDK jest zasadniczo kompletnym środowiskiem wytwarzania gier oferując rozmaite narzędzia modelowania poziomów, w tym: edytor brył geometrycznych, siatek obiektów i terenu, bibliotekę...
-
Knowledge management in the processes of project requirements analysis
PublikacjaAuthors, based on one of popular software project management methods as RUP fo-cused on one of most important discipline in project management as requirements management. Authors decomposed the role of the business analyst and present methodological and realizational processes of knowledge managament in traditional and applied sources of knowledge tied with this role. An experiment was conducted in four project teams of all sizes,...
-
Air journal bearing utilizing near-field acoustic levitation: stationary shaft case
PublikacjaResults of a study to examine a unique idea of self-levitating journal bearing are presented in this paper. the idea represents a radical departure from the current bearing technology. it utilisesacoustic levitation, which relies on the sound energy radiated by an object supporting a load. acoustic levitation has been demonstrated to support loads of up to 10 kg. in order to support a load theacoustic wave emitted by the radiating...
-
Technology-Enhanced Environmental Learning: Co-design of Educational Mobile Application Case
PublikacjaThe process of co-creating an educational mobile application to support environmentally friendly behavior is presented in this paper. The research material consisted of quantitative data collected on the application during the first testing phase by early adopters. The results suggest that the most frequently used features of the app were related to transport and educational activities. While women tended to split their time between...
-
Experimental study of the multi-disc negative brake for a hydraulic motor
PublikacjaThis paper describes the methodology for experimental testing of a multi-disc brake. The construction of this brake was also present. The brake is dedicated to hydraulic motors with a small working volume. Experimental tests were carried out on a brake with plates immersed in oil and, for comparison, tests were carried out on a dry brake. As a result of the tests, the permissible torque (load) that is able to transfer the brake...
-
Risk Analysis by a Probabilistic Model of the Measurement Process
PublikacjaThe aim of the article is presentation of the testing methodology and results of examination the probabilistic model of the measurement process. The case study concerns the determination of the risk of an incorrect decision in the assessment of the compliance of products by measurement. Measurand is characterized by the generalized Rayleigh distribution. The model of the meas-urement process was tested in parallel mode by six risk...
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublikacjaThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
Metoda diagnostyki łożysk na podstawie analizy przebiegów prądu i napięcia zasilającego silnik indukcyjny.
PublikacjaW niniejszej monografii przedstawiono oryginalne podejście i realizację diagnostyki łożysk silników indukcyjnych przy użyciu metody opartej na pomiarach i analizie iloczynu wartości chwilowych prądu i napięcia zasilającego maszyny. Uzyskane wyniki badań eksperymentalnych na obiektach rzeczywistych okazały się zbieżne z wynikami badań symulacyjnych i potwierdziły, że powstanie uszkodzeń łożysk w silniku skutkuje pojawieniem się...
-
Near-Field Wireless Sensing of Plastics and Papers Using Frugal Peel-Off Passive Tag
PublikacjaThis article presents a novel frugal approach of testing plastics and papers using a near-field microwave sensing technique with a peel-off tag. The proposed sensing technique involves two electrical entities: the sensor, which may be regarded as a reader, and a disposable tag. The reader is a modified design of a gap-coupled microstrip line (GCML) sensor, while the passive tag is a standard double-ring complementary split-ring...
-
Influence of dispersed phase content on the mechanical properties of electroless nanocomposite Ni-P/Si3N4 and hybrid Ni-P/Si3N4/graphite layers deposited on the AW-7075 alloy.
PublikacjaThe article presents the results of mechanical testing of Ni-P/Si3N4 nanocomposite and hybrid Ni-P/Si3N4/graphite coatings deposited on AW-7075 aluminum alloy using the chemical reduction method. In terms of mechanical testing, microhardness was measured, and surface roughness and adhesion of the coatings to the aluminum substrate were determined using the “scratch test” method. The surface morphology of the deposited layers was...
-
Opracowanie ekspertyzy dotyczącej przyczyn pękania łopatek wirnika SP turbiny PG1 typu 13UP55
PublikacjaZakres badań i analiz dotyczył ustalenia przyczyn pękania elementów łopatek wirnika SPA5 turbiny TG1 typu 13UP55 obejmował: 1. wykonanie badań składu chemicznego stali, z której wykonano łopatki dostarczone przez Zleceniodawcę dwoma metodami, 2. badania mikroobszarów zniszczenia łopatek na mikroskopie elektronowym skaningowym z mikroanalizatorem EDS, 3. badania metalograficzne makroskopowe i mikroskopowe fragmentów...
-
Quality assessment of ZnO-based varistors by 1/f noise
PublikacjaNoise has been used as a diagnostic tool of surge arrester varistor structures comprising of ZnO grains of various type and size. The physical and electrical properties of the measured samples have been described. In the experimental study, the applied measurement system and the results of noise measurements for the selected structures of varistors designed for the continuous working voltage 280 V, 440 V and 660 V have been presented....
-
Właściwości mechaniczne tworzywa PET - przegląd literatury
PublikacjaThe article describes the influance of the microstructure and environment conditions on the mechanical properties of PET material. From the microskopic point of view, mechanical and thermal properties of PET material have the biggest influance on orientation and crystallization processes of material. From the macroskopic point of view mechanical properties can be described by parameters derived from strees-strain mechanical answers...
-
Corrosion monitoring by harmonic analysis in aqueous environments
PublikacjaThis paper presents tests concerning the rate of corrosion in non-alloy steel (type S235JR) in an aqueous environment, with an additive of sodium chloride by means of polarization resistance measurements and harmonic analysis. The tests have been carried out for steel samples exposed to the testing environment for six weeks, in order to obtain a constant rate of corrosion in the function of time. The measurements have aimed at...
-
Parameters optimization in medicine supporting image recognition algorithms
PublikacjaIn this paper, a procedure of automatic set up of image recognition algorithms' parameters is proposed, for the purpose of reducing the time needed for algorithms' development. The procedure is presented on two medicine supporting algorithms, performing bleeding detection in endoscopic images. Since the algorithms contain multiple parameters which must be specified, empirical testing is usually required to optimise the algorithm's...
-
Integrity level verification for safety-related functions
PublikacjaThis article describes methods for safety integrity level (SIL) verification of safety-related functions with regard to probabilistic criteria given international standards IEC 61508 and IEC 61511. These functions are to be realized using the electrical, electronic and programmable electronic (E/E/PE) systems or safety instrumented systems (SIS). Some methods are proposed for quantitative probabilistic modelling taking into account...
-
Orientation effects on the fracture behaviour of additively manufactured stainless steel 316L subjected to high cyclic fatigue
PublikacjaIn this paper, stainless steel 316L (SS316L) bars were additively manufactured (AM) in three orientations (Z – vertical, XY – horizontal, ZX45 – midway between vertical and horizontal) by using the Laser Powder Bed Fusion Melting (LPBF-M) method. The AM specimens were subjected to load control fatigue testing under full tension and compression (R = -1) at stress amplitudes ±350, ±400 and ±450 MPa. The XY and ZX45 printing orientations...
-
Electronic Noses for Indoor Air Quality Assessment
PublikacjaThis chapter presents a proposal of the use of electronic noses in the monitoring of indoor air quality. The main focus is put on the detailed characteristics of today’s indoor air quality control methods, the types of pollution in the air, and the development of electronic noses for air testing. Currently, scientists seek methodological and structural solutions that would enable real-time online indoor air control. It has been...
-
Machine Learning Applied to Aspirated and Non-Aspirated Allophone Classification—An Approach Based on Audio "Fingerprinting"
PublikacjaThe purpose of this study is to involve both Convolutional Neural Networks and a typical learning algorithm in the allophone classification process. A list of words including aspirated and non-aspirated allophones pronounced by native and non-native English speakers is recorded and then edited and analyzed. Allophones extracted from English speakers’ recordings are presented in the form of two-dimensional spectrogram images and...
-
Tribological Properties of Thermoplastic Materials Formed by 3D Printing by FDM Process
PublikacjaThe dataset entitled 3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4 contains: the time base (expressed in seconds and minutes), the friction torque for sliding friction, rotational velocity of the counter – specimen (velocity of sliding), friction coefficient, load in the friction contact...
-
THE USE OF FEM FOR DETERMINATION OF RESONANT FREQUENCIES OF CIRCULAR SAW BLADES WITH INDIRECT TEETH IN GULLETS
PublikacjaUnderstanding the dynamical properties of the circular saw blade is necessary, since, there is a really need for a stable work at working rotational speeds, which are determined by frequencies at which the circular saw blade tends to vibrate. It was observed that the resonant frequency depend on the circular saw blade shape, a collar diameter and on saw’s teeth shape. In the presented work an attention was paid to the effect of...
-
Rheology of polymer blends
PublikacjaPolymer blends are physical mixtures of two or more homopolymers or copolymers. This type of materials have wide spectrum of technological applications, and their properties are influenced, e.g., by the properties of single components and morphology of final material. The rheology of polymer blends is connected with the processing of polymer blends and is influenced by thermodynamics, morphology, and their evolution during testing....
-
Właściwości stali S460M napawanej pod wodą metodą lokalnej komory suchej
PublikacjaW artykule przedstawiono wyniki badań próbek ze stali S460M wykonanych pod wodą metodą lokalnej komory suchej. Pomiary twardości oraz analiza strukturalna wykazały, że dla określonych ilości wprowadzonego ciepła możliwe jest wykonanie złączy bez niezgodności spawalniczych. Stwierdzono formowanie się w pewnych warunkach pęknięć zimnych w SWC wywołanych procesami odprowadzania ciepła z materiału, które są charakterystyczne dla spawania...
-
INNOVATIVE THERMODYNAMICAL CYCLES BASED ON ENHANCEMENT MASS, MOMENTUM, ENTROPY AND ELECTRICITY TRANSPORT DUE TO SLIP, MOBILITY, TRANSPIRATION, ENTROPY AND ELECTRIC JUMPS AS WELL AS OTHER NANO-FLOWS PHENOMENA
PublikacjaIn our work, a further development of the authors model of thermo-chemical flow of fuel, air, oxygen, steam water, species, ionic and electron currents within nano channels and nano-structures of novel devices is presented. Different transport enhancement models are taken into account -among them the most important are: the velocity slip connected with complex external friction, the Darcy mobility and the Reynolds transpiration....
-
Diagnostic Model of Crankshaft Seals
PublikacjaT he paper presents a research stand being a diagnostic model of radial lip seals used, among others, on crankshafts of piston combustion engines in order to identify the correctness of their operation. The possibility of determining the technical condition of lip seals on the basis of the proposed coefficient of correctness of operation has been described. T he basic features of seals influencing their correctness of...
-
Thermodynamic Cycle Concepts for High-Efficiency Power Plants. Part B: Prosumer and Distributed Power Industry
PublikacjaAn analysis was carried out for different thermodynamic cycles of power plants with air turbines. A new modification of a gas turbine cycle with the combustion chamber at the turbine outlet has been described in the paper. A special air by-pass system of the combustor was applied, and in this way, the efficiency of the turbine cycle was increased by a few points. The proposed cycle equipped with an effective heat exchanger could...
-
Effect of selected ammonia escape inhibitors on carbon dioxide capture and utilization via calcium carbonate precipitation
PublikacjaCarbon dioxide was used to precipitate CaCO3 with CaCl2 solution in the presence of NH3 as a CO2 absorption promoter. Compounds that were previously indicated as inhibitors of ammonia escape during CO2 absorption were also added to the reaction mixture. Inorganic salts, i.e. ZnCl2, CuCl2, CoCl2, and organic substances, i.e. glycerol, ethylene glycol and triethanolamine were tested inhibitors in this work. A model post-distillation...
-
Thermal failure of a second rotor stage in heavy duty gas turbine
PublikacjaThe impulse mode of operation and the supply of various types of fuels causes frequent failures even in the heavy duty gas turbines. The paper presents the ravages of second rotor stage failure in a gas turbine. The excessive thermal elongation rise caused by fuel change was indicated as the main cause. We applied nonlinear numerical analysis, preceded by thermodynamic calculations of the turbine and visual inspection of the effects...
-
The Effect of Fly Ash Microspheres on the Pore Structure of Concrete
PublikacjaThe fly ash microspheres (FAMs) formed during the mineral transformation stage in coal combustion are hollow spherical particles with a density less than water. This paper presents the results of X‐ray micro‐computed tomography and an automatic image analysis system of the porosity in the structure of hardened concrete with microspheres. Concrete mixtures with ordinary Portland cement and two substitution rates of cement by microspheres—5%...
-
Network-aware Data Prefetching Optimization of Computations in a Heterogeneous HPC Framework
PublikacjaRapid development of diverse computer architectures and hardware accelerators caused that designing parallel systems faces new problems resulting from their heterogeneity. Our implementation of a parallel system called KernelHive allows to efficiently run applications in a heterogeneous environment consisting of multiple collections of nodes with different types of computing devices. The execution engine of the system is open for...
-
Smooth start for strategry game development supported by XNA framework
PublikacjaTo attract young and casual game developers, Microsoft created a set of libraries oriented towards easier game development and end-product management. The aim of XNA Framework is to provide a unified software development environment for creating games for both PC's and dedicated platforms like XBOX consoles or mobile phones capable of 3D acceleration. The use of modern, object oriented languages available for the .NET platform...
-
Slowly-closing valve behaviour during steam machine accelerated start-up
PublikacjaThe paper discusses the state of stress in a slowly-closing valve during accelerated start-up of a steam turbine. The valve is one of the first components affected by high temperature gradients and is a key element on which the power, efficiency and safety of the steam system depend. The authors calibrated the valve model based on experimental data and then performed extended Thermal-FSI analyses relative to experiment. The issue...
-
Production of six-degrees-of-freedom (6DoF) navigable audio using 30 Ambisonic microphones
PublikacjaThis paper describes a method for planning, recording, and post-production of six-degrees-of-freedom audio recorded with multiple 3rd order Ambisonic microphone arrays. The description is based on the example of recordings conducted in August 2020 with the Poznan Philharmonic Orchestra using 30 units of Zylia ZM-1S. A convenient way to prepare and organize such a big project is proposed – this involves details of stage planning,...
-
On EM-driven size reduction of antenna structures with explicit constraint handling
PublikacjaSimulation-driven miniaturization of antenna components is a challenging task mainly due to the presence of expensive constraints, evaluation of which involves full-wave electromagnetic (EM) analysis. The recommended approach is implicit constraint handling using penalty functions, which, however, requires a meticulous selection of penalty coefficients, instrumental in ensuring optimization process reliability. This paper proposes...
-
Optimisation of turbine shaft heating process under steam turbine run-up conditions
PublikacjaAn important operational task for thermal turbines during run-up and run-down is to keep the stresses in the structural elements at a right level. This applies not only to their instantaneous values, but also to the impact of them on the engine lifetime. The turbine shaft is a particularly important element. The distribution of stresses depends on geometric characteristics of the shaft and its specific locations. This means a groove manufactured...
-
Techniczne aspekty implementacji nowoczesnej platformy e-learningowej
PublikacjaZaprezentowano aspekty techniczne implementacji nowoczesnej platformy nauczania zdalnego. Omówiono obszary funkcjonalne takie jak: system zarządzania nauczaniem, serwis informacyjny, dodatkowe oprogramowanie dydaktyczne oraz kolekcja zasobów multimedialnych. Przybliżono zagadnienia związane z bezpieczeństwem takiej platformy. Na końcu przedstawiono parametry techniczne wdrożonej na Politechnice Gdańskiej platformy eNauczanie.
-
Experimental and numerical evaluation of mechanical behaviour of composite structural insulated wall panels under edgewise compression
PublikacjaA composite structural insulated sandwich panel (CSIP) is a quite novel approach to the idea of sandwich structures. A series of natural-scale experimental test is required each time a change in panel’s geometry is planned and a reliable computational tool is required to precede actual laboratory testing with virtual simulations. An attempt of creating such a tool has been made with use of a commercial FEM code ABAQUS, in order...
-
AN ATTEMPT AT IDENTIFYING THE INFLUENCE OF TEST HEAD ASSEMBLY STIFFNESS ON THE RESULTS OF A TRIBOLOGICAL EXPERIMENT CONDUCTED UNDER MICRO-OSCILLATION CONDITIONS
PublikacjaThe outcome of experimental research on a group of dry bearing materials carried out under small oscillation conditi ons and using a test rig designed and made at Gdansk University of Technology inspired the decision to find out if the stiffness of test head elements in fluenced the generated results. Therefore, a computer model utilising finite elements was devised and used to simulate the workings of the test head. The mode l...
-
Limitations of Emotion Recognition in Software User Experience Evaluation Context
PublikacjaThis paper concerns how an affective-behavioural- cognitive approach applies to the evaluation of the software user experience. Although it may seem that affect recognition solutions are accurate in determining the user experience, there are several challenges in practice. This paper aims to explore the limitations of the automatic affect recognition applied in the usability context as well as...
-
Optimising approach to designing kernel PCA model for diagnosis purposes with and without a priori known data reflecting faulty states
PublikacjaFault detection plays an important role in advanced control of complex dynamic systems since precise information about system condition enables efficient control. Data driven methods of fault detection give the chance to monitor the plant state purely based on gathered measurements. However, they especially nonlinear, still suffer from a lack of efficient and effective learning methods. In this paper we propose the two stages learning...
-
Reactions on the surface of the implant under the influence of biofilm
PublikacjaThe contact of a biomaterial with the biological environment in in vitro and in vivo tests leads to the production of a particular ecosystem in which the active roles perform both, the material surface and the extracellular matrix protein forming a biofilm. Proteins affect cell and bacteria adhesion processes, biological activity of cells and activation of inflammatory response.The knowledge of the reaction mechanisms active on...
-
Application of spectroscopy to the measurement of blood parameters
PublikacjaSpectroscopy is the study of formation and interpretation of the spectra arising from the interactions of all types of radiation on matter, understood as a collection of atoms and molecules. This is a very important department of optics which gives us many opportunities to measure various parameters such as material blood parameters. Among the diseases that are associated significantly with changes in rheological properties of...