Filtry
wszystkich: 985
wybranych: 919
Wyniki wyszukiwania dla: FINITE ELEMENT METHOD(FEM)
-
Structural response of existing spatial truss roof construction based on Cosserat rod theory
PublikacjaPaper presents the application of the Cosserat rod theory and newly developed associated finite elements code as the tools that support in the expert-designing engineering practice. Mechanical principles of the 3D spatially curved rods, dynamics (statics) laws, principle of virtual work are discussed. Corresponding FEM approach with interpolation and accumulation techniques of state variables are shown that enable the formulation...
-
Thermal analysis of Magnetohydrodynamics (MHD) Casson fluid with suspended Iron (II, III) oxide-aluminum oxide-titanium dioxide ternary-hybrid nanostructures
PublikacjaThis study is carried out to enhance and analyze the thermal performance of non-Newtonian Casson fluid by immersing Ternary hybrid nanoparticles Fe3O4-Al2O3-TiO2 uniformly. To model the behaviour of such complex phenomena mathematically, a system of complex transport differential equations is developed by utilizing a non-Fourier heat transfer model for energy transport. The non-dimensional system of transport equations involving...
-
Koncepcja i analiza sensora/aktuatora piezoelektrycznego do pomiaru procesu starzenia się ludzkiej skóry
PublikacjaNiniejszy artykuł przedstawia nową koncepcję piezoelektrycznego sensora/aktuatora przeznaczonego do pomiaru właściwości mechanicznych tkanek miękkich a w szczególności skóry ludzkiej. Wyjaśnione jest analityczne podejście z wykorzystaniem schematu zastępczego Mason’a określającego aktuator w stanie rezonansu oraz opis metody impedancji elektromechanicznej wykorzystanej w systemie pomiarowym. Analiza z użyciem metody elementów...
-
Stress analysis of a strip under tension with a circular hole
PublikacjaThe paper addresses stress analysis of a strip with a circular hole under uniform uniaxial tension based oncircumferential stress expressionρπ. Stresses are analyzed in the infinite-length strips under tension with holes, the ratioof the hole radiusa to the strip half-widthb is either equal to:κ =a/b = 0.1 orκ = 0.5. Circumferential stresses aredetermined in selected cross-sections of the strip. The stress diagrams display local...
-
Footbridges. Dynamic Design – Selected Problems
PublikacjaModern footbridges create challenge in esthetic and structural design. Breaking the proven canons is a recipe for architectural success. However esthetic form has to be also a functional pedestrian bridge. Therefore a good FEM modeling is a key element in engineering part of design. The paper presents selected problems related to the modeling of the dynamic construction of footbridges. Several basic dynamic problems concerning...
-
The methodology of design of axial clearances compensation unit in hydraulic satellite displacement machine and their experimental verification
PublikacjaA new methodology of calculating the dimensions of the axial clearance compensation unit in the hydraulic satellite displacement machine is described in this paper. The methods of shaping the compensation unit were also proposed and described. These methods were used to calculate the geometrical dimensions of the compensation field in an innovative prototype of a satellite hydraulic motor. This motor is characterized by the fact...
-
A Model-Order Reduction Approach for Electromagnetic Problems With Nonaffine Frequency Dependence
PublikacjaThe aim of this paper is to present a novel model-order reduction (MOR) technique for the efcient frequency-domain nite-element method (FEM) simulation of microwave components. It is based on the standard reduced-basis method, but the subsequent expansion frequency points are selected following the so-called sparsied greedy strategy. This feature makes it especially useful to perform a fast-frequency sweep of problems that lead...
-
Smooth Particle Hydrodynamics (SPH) approach in simulating large penetration into soil
PublikacjaA study of Smooth Particle Hydrodynamics (SPH) approach for predicting large soil deformation is presented. Theoretical basics of SPH method, including the equations governing, discussion of the importance of smoothing function length, contact formulation, boundary treatment and finally utilization in hydrocodes simulations are presented. An application of SPH to a real case of large penetrations (crater creating) into soil caused...
-
Reduction of Derivative pipeline effort in water turbine
PublikacjaThe paper presents an approach to evaluate and reduce the effort of the derivative pipeline in a water turbine of a hydrostatic power station in its vulnerable spots. Potential places of the biggest effort of the structure, as well as the coefficient of displacement and safety factor related to them were identified using FEM numerical method. Pipeline reinforcement was designed and made based on FEM analysis. Original technology...
-
FEM modelling of screw displacement pile interaction with subsoil
PublikacjaPredicting the-settlement characteristics of piles is an important element in the designing of pile foundations. The most reliable method in evaluating pile-soil interaction is the static load test, preferably performed with instrumentation for measuring shaft and pile base resistances. This, however, is a mostly post-implementation test. In the design phase, prediction methods are needed, in which numerical simulations play an...
-
Launching of steel bridge girder. Application of nonlinear shell models
PublikacjaThe paper describes the final technology of launching the steel bridge superstructure. The original technology failed in the first construction stage. Local damage of steel webs caused by plastic buckling stopped the procedure. In the effect of damage a new consulting team was employed to solve the problem and redesign a technology of constructing. The key element of the new solution was developed with great help of non-linear...
-
Influence of nonlinearities on the efficiency and accuracy of FEM calculations on the example of a steel build-up thin-walled column
PublikacjaDue to the increase of computing capabilities of standard processing units, it is possible to perform complex analyses, considering a number of nonlinearities, such as geometric, material and boundary (contact) even on personal computers. In the paper, the authors have analysed the efficiency and accuracy of standard PC’s FEM calculations performed in Abaqus CAE 2017 software on the example of a critical load assessment of a thin-walled...
-
THE INTERACTION BETWEEN STEEL COLUMN CHORD AND CLOSELY SPACED REINFORCEMENT.
PublikacjaNowadays, more often than before, civil engineering designers are willing to use steel build-up members composed of single or doubled cold-formed chords interconnected using different mechanical connectors. This paper subject is an analysis of cooperation of a closely spaced built-up cold-formed chord interconnected with series of bolts that are located along the length of the member in a specific spacing. This distance along the...
-
Failure of cold-formed beam: How does residual stress affect stability?
PublikacjaIn machine industry, stresses are often calculated using simple linear FEM analysis. Occasional failures of elements designed in such a way require recomputation by means of more sophisticated methods, eg. including plasticity and non-linear effects. It usually leads to investigation of failure causes and improvement of an element in order to prevent its unwanted behavior in the future. The study presents the case where both linear...
-
Flexural buckling and post-buckling of columns made of aluminium alloy
PublikacjaThe paper concerns flexural buckling and initial post-buckling of axially compressed columns made of aluminium alloy described by the Ramberg-Osgood relationship. The non-linear differential equation of the problem is derived using the stationary total energy principle and the assumptions of classical beam theory within a finite range. The approximate analytical solution of the equation leading to the buckling loads and initial...
-
Experimental tests and numerical simulations of full scale composite sandwich segment of a foot- and cycle- bridge
PublikacjaIn the paper experimental tests and numerical simulations of a full cross-section segment of ultimately designed foot-and cycle-bridge are presented. The experimental tests were conducted on element with length reduced to 3 m and unchanged (target) cross-section dimensions. The external skin of structure is GFRP laminate while internal core is PET foam. Several quasi-static tests were performed using hydraulic cylinder to generate...
-
Wpływ wysokiej osteotomii piszczelowej na mechanikę stawu kolanowego
PublikacjaW rozprawie podjęto próbę weryfikacji wpływu zabiegu chirurgicznego wysokiej osteotomii piszczelowej na mechanikę stawu kolanowego. Po wykonanym przeglądzie literatury, postawiono trzy hipotezy, które poddano weryfikacji na drodze badań numerycznych. Otrzymane wyniki zwalidowano poprzez badania nacisków powierzchniowych występujących w stawach kolanowych świni domowej, prowadzonych na maszynie do jednoosiowego ściskania. Praca...
-
CFD and FEM model of an underwater vehicle propeller
PublikacjaDuring the project execution of design and optimization the Remotely Operated Vehicle (ROV) research on its propulsion has been carried out. The entire project was supported by CFD and FEM calculations, which taking into account the characteristics of underwater vehicle. One of the tasks was to optimize the semi-open duct for horizontal propellers, which provided propulsion and controllability in horizontal plane. In order to...
-
Analiza drgań kładki kompozytowej wywołanych działaniem wiatru
PublikacjaW pracy omówiono sposób przeprowadzenia uproszczonej, numerycznej analizy drgań kładki kompozytowej wywołanych działaniem wiatru. Rozważaniom poddano swobodnie podpartą konstrukcję o rozpiętości 16 m i przekroju w kształcie litery U. W pierwszej kolejności przeprowadzono dwuwymiarową analizę opływu niepodatnego kształtu przekroju kładki w poziomym strumieniu wiatru o prędkości 10 m/s. Obliczenia numeryczne przeprowadzono programem...
-
NUMERICAL SIMULATION OF CRATER CREATING PROCESS IN DYNAMIC REPLACEMENT METHOD BY SMOOTH PARTICLE HYDRODYNAMICS
PublikacjaA theoretical base of SPH method, including the governing equations, discussion of importance of the smoothing function length, contact formulation, boundary treatment and finally utilization in hydrocode simulations are presented. An application of SPH to a real case of large penetrations (crater creating) into the soil caused by falling mass in Dynamic Replacement Method is discussed. An influence of particles spacing on method...
-
VIBRATION DIAGNOSTICS OF FOOTBRIDGE WITH USE OF ROTATION SENSOR
PublikacjaThe benefits of the additional measurement of rotational degrees of free-dom on the performance of the vibration diagnosis of bridges are studied in this paper. The common vibrational diagnostics that uses translational degrees of freedom is extended by measurements of rotations. The study is curried out on a footbridge and the presence of damage as well as its location and size is determined with use of FEM updating procedure....
-
Monte Carlo simulations of the fracture resistance degradation of asphalt concrete subjected to environmental factors
PublikacjaThe paper presents the results of laboratory tests of SCB (semi-circular beam) samples of asphalt concrete, subjected to the destructive effect of water and frost as well as the aging processes. The determined values of material parameters show significant dispersions, which makes the design of mixtures difficult. Statistical analysis of the test results supplemented by computer simulations made with the use of the proprietary...
-
The impact of the shape of deep drilled well screen openings on the filtration process in full saturation conditions
PublikacjaThe authors propose a supplementary method of modelling seepage flow around the deep drilled well screen. The study applies 3D numerical modelling (FEM) in order to provide an in-depth analysis of the seepage process. The analysis of filtration parameters (flow distribution q(x,t) and pressure distribution p) was conducted using the ZSoil.PC software system. The analysis indicates that the shape of perforation is of secondary importance...
-
Residue-Pole Methods for Variability Analysis of S-parameters of Microwave Devices with 3D FEM and Mesh Deformation
PublikacjaThis paper presents a new approach for variability analysis of microwave devices with a high dimension of uncertain parameters. The proposed technique is based on modeling an approximation of system by its poles and residues using several modeling methods, including ordinary kriging, Adaptive Polynomial Chaos (APCE), and Support Vector Machine Regression (SVM). The computational cost is compared with the traditional Monte-Carlo...
-
Load-settlement characteristics of piles working in a group
PublikacjaLoad-settlement characteristic (Q-s) of an axially loaded pile can be empirically determined from a static pile load test or on the basis of calculations using, e.g. transfer functions or numerical methods (FEM). The transfer functions method usually rely on empirical data, i.e. the function parameters are determined on the basis of numerous pile test results. Thus this method takes into account pile installation technology and...
-
Comparative 3D DEM simulations of sand–structure interfaces with similarly shaped clumps versus spheres with contact moments.
PublikacjaThree-dimensional simulations of a monotonic quasi-static interface behaviour between initially dense cohesionless sand and a rigid wall of different roughness during tests in a parallelly guided direct shear test under constant normal stress are presented. Numerical modelling was carried out by the discrete element method (DEM) using clumps in the form of convex non-symmetric irregularly shaped grains. The clumps had an aspect...
-
Determination of leakage inductances of multi-winding and single-phase transformer
PublikacjaThis paper presents the method for determination of leakage inductances of single-phase and multi-winding transformer. The matrix of leakage inductances takes into account leakage self and also leakage mutual magnetic couplings. It is assumed that there is a flux common to all windings and several leakage fluxes referred to a particular winding. The flux linkages of each coil needed fo calculation of leakage inductances was computed...
-
Hybrid model of geared rotor system
PublikacjaIn the paper a hybrid model of a geared multirotor system has been developed. The model is obtained by application of both the modal decomposition methodology and the spatial discretization method. Reduced modal model was constructed for the system without gyroscopic and damping effects. The gyroscopic interaction, damping and other phenomena which are difficult to include in the modal approach were modeled by application of simply...
-
Vibration of the bridge under moving singular loads - theoretical formulation and numerical solution
PublikacjaThe paper presents the results of the numerical analysis of a simple vehicle passing over a simply supported bridge span. The bridge is modelled by a Euler-Bernoulli beam. The vehicle is modelled as a linear, visco-elastic oscillator, moving at a constant speed. The system is described by a set of differential equations of motion and solved numerically using the Runge-Kutta algorithm. The results are compared with the solution...
-
Non-linear FEM analysis of pounding-involved response of buildings under non-uniform earthquake excitation
PublikacjaThe aim of the paper is to show the results of the study investigating the influence of non-uniform earthquake excitation, due to spatial seismic effects connected with the propagation of seismic wave, on the pounding-involved response of two buildings. The three-dimensional non-linear FEM analysis has been conducted using the detailed models of colliding structures. Acceleration records for different structural supports have been...
-
The use of a two-phase Monte Carlo material model to reflect the dispersion of asphalt concrete fracture parameters
PublikacjaThe work covers comprehensive laboratory tests of semi-circular bending (SCB) of asphalt concrete samples. The results of two test series, including four and 32 SCB specimens, indicate a substantial scatter of force–deflection (F-d) histories. The numerical analysis is aimed to reflect the maximum breaking load and fracture energy of the samples, pointing out their random character. The original simulation-based fictitious Monte...
-
Electrostatic Zipping Actuators—Analysis of the Pull-In Effect Depending on the Geometry Parameters
PublikacjaContinuous work on a new generation of actuators, referred to as artificial muscles, resulted in the initiation of work on electrostatic zipping actuators, the concept of which is derived from micro electro-mechanical devices. Despite partial knowledge of their basic operating parameters, a question remains whether electrostatic zipping actuators are able to meet the expectations in the context of generated forces and control possibilities....
-
Probabilistic estimation of diverse soil condition impact on vertical axis tank deformation
PublikacjaThe calculations of fuel tanks should take into account the geometric imperfections of the structure as well as the variability of the material parameters of the foundation. The deformation of the tank shell can have a significant impact on the limit state of the structure and its operating conditions. The paper presents a probabilistic analysis of a vertical-axis, floating-roof cylindrical shell of a tank with a capacity of 50000...
-
Reinforced concrete thin wall dome after eighty years of operation in maritime climate environment
PublikacjaThe paper presents a description of the construction elements of the Gdynia Seaport main hall dome. Firstly, it provides information about the technical condition of the dome’s structure. Secondly, it examines the strength analysis of the thin-walled reinforced concrete dome covering. Throughout the last 80 years the building has been exposed to an unfavourable marine climate. The analysis of the state of stress and deformations...
-
Numerical modeling and experimental validation of full-scale segment to support design of novel GFRP footbridge
PublikacjaThe paper contains analysis of full-scaled three meters long segment of a novel composite footbridge. Both numerical modeling and experimental validation were performed. Analyzed object is a shell type sandwich channel-like structure made of composite sandwich with GFRP laminates as a skin and PET foam as a core. Several static load schemes were performed including vertical and horizontal forces. In FEM analysis multilayered laminate...
-
Prediction of cast-in-place concrete strength of the extradosed bridge deck based on temperature monitoring and numerical simulations
PublikacjaThe work is devoted to the implementation of a monitoring system for high performance concrete embedded in the span of an extradosed bridge deck using a modified maturity method augmented by numerical simulations conducted by the authors’ FEM code. The paper presents all research stages of bridge construction and considers the conclusions drawn from the results of laboratory tests, field measurements, and numerical calculations....
-
Determination of the minimal critical rotational speeds of the circular saw blades with the quasi-twin resonant frequencies
PublikacjaTo determine the minimal critical rotational speeds of the circular saw blades is the fundamental aspect of obtaining the range of the rotational operating speeds, by which the circular saw blade can work with required stability. While for the circular saw blades with full-homogeneous bodies the determination of such rotational speeds is the relatively low level of difficulty function, whereas for circular saw blades with more...
-
Experimental and numerical studies on the mechanical response of a piezoelectric nanocomposite-based functionally graded materials
PublikacjaThis work presents an experimental study of piezoelectric structures reinforced by graphene platelets, based on the concept of the functionally graded materials (FGMs). The assumed model is a rectangular beam/plate and the composition is due to the Halpin-Tsai rule. The model is also simulated in the Abaqus software which is the first time that such a structure has been modelled in an FEM package. In addition, a mathematical model...
-
Applications of the discrete green's function in the finite-difference time-domain method
PublikacjaIn this paper, applications of the discrete Green's function (DGF) in the three-dimensional (3-D) finite-difference time-domain (FDTD) method are presented. The FDTD method on disjoint domains was developed employing DGF to couple the subdomains as well as to compute the electromagnetic field outside these subdomains. Hence, source and scatterer are simulated in separate subdomains and updating of vacuum cells, being of little...
-
Solution of the dike-break problem using finite volume method and splitting technique
PublikacjaIn the paper the finite volume method (FVM) is presented for the solution of two-dimensional shallow water equations. These equations are frequently used to simulate the dam-break and dike-break induced flows. The applied numerical algorithm of FVM is based on the wave-propagation algorithm which ensures a stable solution and simultaneously minimizes the numerical errors. The dimensional decomposition according to the coordinate...
-
The Quick Measure of a Nurbs Surface Curvature for Accurate Triangular Meshing
PublikacjaNURBS surfaces are the most widely used surfaces for three-dimensional models in CAD/CAE programs. As a model for FEM calculation is prepared with a CAD program it is inevitable to mesh it finally. There are many algorithms for meshing planar regions. Some of them may be used for meshing surfaces but it is necessary to take the curvature of the surface under consideration to avoid poor quality mesh. The mesh must be denser in the...
-
The elasto-plastic numerical study of crack initiation in notched PMMA specimens under uniaxial loading conditions – Tension and torsion
PublikacjaThis paper presents the results of FEM numerical calculations aimed at describing the plastic strain and stress fields under critical loading conditions: tensile force or torsional moment. The calculations were carried out with reference to the results of experimental tensile and torsional tests of flat PMMA specimens weakened with V-notches of different root radii: 0.5, 2 and 10 mm. The procedure for conducting nonlinear numerical...
-
Fast Design Optimization of Waveguide Filters Applying Shape Deformation Techniques
PublikacjaThis paper presents an efficient design of microwave filters by means of geometry optimization using shape deformation techniques. This design procedure allows for modelling complex 3D geometries which can be fabricated by additive manufacturing (AM). Shape deforming operations are based on radial basis function (RBF) interpolation and are integrated into an electromagnetic field simulator based on the 3D finiteelement method (FEM)....
-
Locking effects in finite elemnt method
PublikacjaIn the present paper a short survey of the locking effect literature is given. As this area of scientific research is still developing, the author of the paper restricted it to about 70 papers. This study is proposed as an introduction to the comprehensive investigation of locking effects.
-
Implementation of the Boundary Element Method to Two-Dimensional Heat Transfer with Thermal Bridge Effects
PublikacjaThe work presents an application of the boundary element method applied to a two-dimensional conductive heat transfer. The algorithm of the method is explained and its advantages are outlined. Green's function as a fundamental solution for Poisson's equation in two dimensions was used and the direct approach was applied. The presented results concern building construction elements as typical cases of thermal bridges. Some properties...
-
A spline-based FE approach to modelling of high frequency dynamics of 1-D structures
PublikacjaIn this paper a computational methodology leading to the development of a new class of FEs, based on the application of continuous and smooth approximation polynomials, being splines, has been presented. Application of the splines as appropriately defined piecewise elemental shape functions led the authors to the formulation of a new approach for FEM, named as spFEM, where contrary to the well-known NURBS approach, the boundaries...
-
Application of the Boundary Element Method for the Simulation of Two-dimensional Viscous Incompressible Flow
PublikacjaThe paper presents the application of an indirect variant of the boundary element method (BEM) to solve the two-dimensional steady flow of a Stokes liquid. In the BEM, a system of differential equations is transformed into integral equations. Thi smakes it possible to limit discretization to the border of the solution. Numerical discretization of the computational domain was performed with linear boundary elements, for which a...
-
Decomposition of the induced magnetism degaussing problem for fast determination of currents in demagnetization coils wrapped outside an object under arbitrary external field conditions
PublikacjaSafe passage of ships in the presence of sea mines can be ensured by limiting or reducing the ship’s magnetic footprint. For vessels with plastic hulls, the main component that requires magnetic damping is the engine. Demagnetization of such an object can be achieved by wrapping it with coils and setting the direct current appropriately. For each specific geographic location, the currents in the coils can be determined iteratively...
-
Application of hybrid finite-difference mode-matching method to analysis of structures loaded with axially-symmetrical posts
PublikacjaW artykule przedstawiono nową metodę hybrydową do analizy układów falowodowych zawierających dowolne konfiguracje obiektów osiowo-symetrycznych. Metoda oparta jest na połączeniu metody różnic skończonych, metody dopasowania rodzajów oraz iteracyjnej procedury rozpraszania. W pracy przedstawiono badania zbieżności metody. Uzyskane wyniki numeryczne porównano z wynikami odniesienia. Duża zgodność wyników potwierdziła poprawność opracowanego...
-
Analysis of ring cracks in ceramic rolling elements using the boundary element method
PublikacjaCeramic materials have been increasingly used in bearing technology for over a dozen years. This is due to the characteristic properties of ceramic materials such as: high hardness, corrosion resistance, the possibility of use in aggressive chemical environments, as well as due to the lower specific weight compared to steel materials. However, the use of ceramic materials is connected with many limitations. The main disadvantages...