Wyszukiwarka
Filtry
wszystkich: 481
wybranych: 450
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: MODEL TESTS IN THE TOWING TANK
-
Energy Demand of Short-Range Inland Ferry with Series Hybrid Propulsion Depending on the Navigation Strategy
PublikacjaInterest in hybrid propulsion systems that can be used on small vessels has increased significantly in recent years. They can replace inefficient and environmentally burdensome conventional systems based on diesel engines. Hybrid propulsion has many advantages such as high energy efficiency and virtually noiseless operation, and therefore it fits well with the current trends of “green shipping” and “zero emission”. The aim of the...
-
Reliability estimation of underground horizontal fuel tank limit states
PublikacjaFuel tanks are designed with regard to standard loads and operating conditions. The investigations of the paper show the impact of such factors as tank corrosion and other means on the variation of stress fields and deformation of the underground horizontal tank shell. The introduction of probabilistic methods allows for structural reliability assessment. While the computational time of the entire tank FEM model is high, the preliminary...
-
Identification of dynamic parameters in the context of diagnostics of steel tank with different level of liquid.
PublikacjaThe paper presents an experimental study to identify the dynamic parameters of a water-filled tank model. The experimental modal analysis approach involving the excitation at one point of the structure and acquisition of vibra tions at selected points distri buted over the tank surface allowed to determine the resonance frequencies, mode shapes and damping ratios. The main aim of the research was to examine the influence of...
-
Experimental study on models of cylindrical steel tanks under mining tremors and moderate earthquakes
PublikacjaThe aim of the study is to show the results of complex shaking table experimental investigation focused on the response of two models of cylindrical steel tanks under mining tremors and moderate earthquakes, including the aspects of diagnosis of structural damage. Firstly, the impact and the sweep-sine tests have been carried out, so as to determine the dynamic properties of models filled with different levels of liquid. Then,...
-
Synthesis of a state feedback controller for an averaging tank with variable filling
PublikacjaIn paper, a nonlinear averaging tank with variable filling is considered. The main purpose of this research work was the modelling and control system synthesis of an averaging tank. The control objectives included ensuring stability and zero steady-state error of the system and achieving settling time as short as possible, while maintaining a minimal overshoot. In order to achieve the intended purpose, firstly a mathematical model...
-
Using differential pressure sensor to measure nitrous oxide level in a tank
PublikacjaA method for measuring the level of liquid nitrous oxide oxidizer in a hybrid rocket motor oxidizer tank is proposed. Presented approach is more accurate than the most commonly used method of this measurement, which employs weighting of the whole sounding rocket or an oxidizer tank. In our solution we use a differential pressure sensor to measure the change of pressure at the bottom of an oxidizer tank in comparison to the pressure...
-
Simplified Method of Modelling Behaviour of Ship in Waves with Partially Flooded Compartments
PublikacjaThis paper contains a description of a numerical model for calculating behaviour of ships in waves. There are many models available, but the one described here can be characterised with a set of parameters that have a decisive impact on the final values of roll motion amplitude and frequency. In this paper, it is shown how a fitting of a standard-shape hull characterised by certain readily available parameters affects...
-
Design of three control algorithms for an averaging tank with variable filing
PublikacjaAn averaging tank with variable filling is a nonlinear multidimensional system and can thus be considered a complex control sys-tem. General control objectives of such object include ensuring stability, zero steady state error and achieving simultaneously shortest possible settling time and minimal overshoot. The main purpose of this research work was the modelling and synthesis of three control systems for an averaging tank. In...
-
Multi-objective optimization of water quality, pumps operation, and storage sizing of water distribution systems
PublikacjaA multi-objective methodology utilizing the Strength Pareto Evolutionary Algorithm (SPEA2) linked to EPANET for trading-off pumping costs, water quality, and tanks sizing of water distribution systems is developed and demonstrated. The model integrates variable speed pumps for modeling the pumps operation, two water quality objectives (one based on chlorine disinfectant concentrations and one on water age), and tanks sizing cost...
-
Numerical simulation of temperature distribution of heat flow on reservoir tanks connected in a series
PublikacjaThe flow of temperature distribution through a medium in thermodynamic studies plays an important role in understanding physical phenomena in chemical science and petroleum engineering, while temperature distribution indicates the degree of reaction that must be undergone to obtain the final product. Therefore, this paper aims to present and apply the exponential matrix algorithm (EMA), differential transformation algorithm (DTA),...
-
Accelerated large scale test set-up design in natural corrosion marine environment
PublikacjaThe standards for conducting small-scale specimen tests are well developed, but there is a lack of direct guidelines for conducting corrosion tests for large-scale specimens. The objective here is to develop a methodology which may be used in designing an accelerated corrosion test of large-scale structural components subjected to a natural corrosion marine environment. Different factors influencing corrosion degradation of steel...
-
Design of septic tanks placed on cohesive soils
PublikacjaThe paper presents a short review of literature with regard to design and erection of the reinforced concrete and concrete tanks. The authors investigated the underground septic tank with of 10 m3 capacity placed on cohesive soils. The authors compared the values of internal forces for soils in drained and undrained conditions with different geotechnical parameters: loamy sand of liquidity index IL = 0.1 and IL = 0.7 and clay with...
-
APPLICATION OF VORTEX FLOW MODEL IN PROPELLER-STATOR SYSTEM DESIGN AND ANALYSIS
PublikacjaThe paper covers basics of the vortex model used for propeller-stator systems. The outline of the design algorithm is given and the results of its application are shown. The designed propeller-stator system was the subject of model tests run at the CTO model basin and cavitation tunnel. Stator’s influence on the delivered power required by the propeller and its revolution rate has been examined by conducting self-propulsion...
-
NUMERICAL ESTIMATION OF HULL HYDRODYNAMIC DERIVATIVES IN SHIP MANOUVERING PREDICTION
PublikacjaOperating in crowded waterways pose a risk of accidents and disasters due to maneuvering limitations of the ship. In order to predict ship’s maneuvering characteristics at the design stage, model tests are often executed as the most accurate prediction tool. Two approaches can be distinguished here: free running model tests and numerical simulations based on planar motion model with the use of hydrodynamic derivatives obtained...
-
Rola i znaczenie zbiornika sieciowego w kształtowaniu hydrauliki i jakości wody w systemie wodociągowym
PublikacjaEksploatacja zbiornika sieciowego powinna zapewniać cykliczną wymianę wody w jego komorach. Koniecznym warunkiem prawidłowej eksploatacji zbiornika jest zgodność założeń projektowych ze stanem faktycznym. Praktyka eksploatacyjna wskazuje na szereg nieprawidłowości w tym względzie. Z powodu lokalizacji zbiornika sieciowego za nisko lub za wysoko albo wskutek błędów popełnionych w ustaleniu jego parametrów obserwuje się niestabilność...
-
Analiza wpływu transmisji danych na jakość działania rozproszonych systemów sterowania
PublikacjaW artykule przedstawiono zagadnienia związane z transmisją danych w rozproszonych systemach sterowania. Opisano cechy charakterystyczne przemysłowych sieci i protokołów informatycznych. Utworzono model rozproszonego systemu sterowania poziomem cieczy w zbiorniku, w którym komunikacja oparta została na protokole Modbus RTU. Na podstawie zmian parametrów transmisji danych wykazano, że poprawna komunikacja pomiędzy elementami systemu...
-
From U2TP Models to Executable Tests with TTCN-3
PublikacjaThe approach towards system engineering according to Model-Driven Architectures (MDA) with code generation derived from model implies also an increased need for research on automation of the test generation process. This paper presents an approach to derive executable tests from UML 2.0 Testing Profile diagrams automatically. In particular, an approach to derive executable tests within the Testing and Test Control Notation (TTCN-3)...
-
Prediction of manoeuvring abilities of 10000 DWT pod-driven coastal tanker
PublikacjaThis paper aims to present a new approach in the prediction of manoeuvring abilities of pod-driven ships. A new mathematical model of motions based on MMG methodology was developed and a new type of description of forces acting on azimuth drives is presented. Captive model tests of medium-size coastal tanker and pod open water tests were carried out in CTO S.A. (Ship Design and Research Centre S.A.) to obtain hull hydrodynamic derivatives...
-
A robust sliding mode observer for non-linear uncertain biochemical systems
PublikacjaA problem of state estimation for a certain class of non-linear uncertain systems has been addressed in this paper. In particular, a sliding mode observer has been derived to produce robust and stable estimates of the state variables. The stability and robustness of the proposed sliding mode observer have been investigated under parametric and unstructured uncertainty in the system dynamics. In order to ensure an unambiguous non-linear...
-
Mechanical properties of Precontraint 1202 S2 based on uniaxial tensile and creep tests
PublikacjaThe purpose of the paper is the estimation of the polyvinyl chloride – polyester-coated fabric (Precontraint 1202 S2) mechanical properties under uniaxial tensile tests as well as short- and long-time creep tests. The uniaxial tests are the basis of non-linear elastic description while the creep tests are used for the evaluation of the stiffness parameters in time and for the identification of the standard viscoelastic model. The...
-
Experimental and numerical evaluation of mechanical behaviour of composite structural insulated panels
PublikacjaComposite structural insulated panels (CSIPs) are novel prefabricated elements for structural applications. Panels under consideration are made from glass-fibre reinforced magnesia cement boards as facesheets and expanded polystyrene foam (EPS) as a core. Quasi-static full-scale and model bending tests under monotonic loading were performed to recognize mechanical properties of CSIPs in flexure. In addition, tensile, compressive,...
-
Projektowanie zbiornika na nieczystości ciekłe
PublikacjaW artykule przedstawiono proces projektowania zbiornika podziemnego na nieczystości ciekłe o pojemności ok. 10 m3 posadowionego na gruntach niespoistych (sypkich). Porównano wartości sił wewnętrznych w przypadku skrajnie różnych warunków gruntowych: piasku drobnego o ID = 0,2 oraz żwiru o I D = 0,7. Dodatkowo przeanalizowano wpływ modelu obliczeniowego podłoża na wyniki sił wewnętrznych. Opisano procedurę normową pozwalającą na...
-
Numerical Simulations of Hydrodynamic Open-Water Characteristics of a Ship Propeller
PublikacjaThe paper presents the results of numerical simulations of ship propeller operation bearing the name of Propeller Open Water (POW) Tests. The object of tests was a sample ship propeller (PPTC1), the geometrical and kinematic data of which are available, along with the results of model tests, on the official page of the research centre involved in the measurements. The research aimed at verifying the correctness of results of numerical...
-
On the validation of the LS-DYNA Geo Metro numerical model
PublikacjaThe paper presents experiences gained during work with numerical model of Geo Metro vehicle used for simulations of crash tests with road safety barriers. Attention is drawn to the subject of tire/wheel breakage during collision events. Some methods for improvement of the model are presented in the paper. Several results for the normative vehicle numerical tests are introduced. Simulations were carried out using LS-DYNA finite...
-
Mechanical properties of Precontraint 1202S coated fabric under biaxial tensile test with different load ratios
PublikacjaThe paper describes a method of laboratory tests necessary for identifying the mechanical properties of polyester coated fabrics named Precontraint 1202S with PVDF surface treatment. Two sets of initial material parameters for dense net model and orthotropic model are specified. Material parameters for Precontraint 1202S coated fabric are specified on the basis of the biaxial tensile tests for different load ratios. In order to...
-
Results of acoustic emission tests of corrosion protection degree of ship steel tanks covered by means of protective coatings (Phase I)
PublikacjaThis paper presents methods and results of the 1st series of tests of acoustic emission (AE) signals, aimed at assessing degree of corrosion protection of a tank made of hull structural steel, protected by means of a protective coating combined from polyurethane layer and concrete filler. The tests were carried outin compliance with a method specially elaborated for application to the work in question. In the method were used requirements...
-
Experimental investigations and damage growth modeling of EN‐AW 2024 aluminum alloy under LCF loading accounting creep pre‐deformation
PublikacjaThis article presents the results of experimental tests of creep rupture and of low-cycle fatigue (LCF) of EN-AW 2024 aluminum alloy devoid of damage and having preliminary damage. The preliminary damage was dealt in the process of creep at elevated temperature 100C, 200C, and 300C until achievement of two different strain values at each temperature. Samples with preliminary damage were subjected to fatigue tests at room temperature....
-
The effect of elevated temperature on LCF damage growth in 2024AA – Experiment and modeling
PublikacjaThis paper presents the results of experimental low-cycle fatigue (LCF) tests conducted on EN-AW 2024 alloy in T3511 temper at 100 ◦C, 200 ◦C and 300 ◦C. The material’s basic fatigue characteristics were determined, such as fatigue life curve and cyclic strain curve. Both the hysteresis loop and nature of fracture surfaces obtained in macro- and microscopic observations (scanning electron microscope, SEM) were accounted for. The...
-
Combined numerical and experimental approach to determine numerical model of abdominal scaffold
PublikacjaA proper junction of the prosthesis and the abdominal wall is important in successful hernia repair. The number of tacks should be balanced to assure appropriate mesh fixation and not to induce post-operative pain. Numerical simulations help to find this balance. The study is aimed at creating a proper numerical model of a knitted surgical mesh subjected to boundary conditions and load occurring in the abdominal cavity. Continuous,...
-
Identification of Bodner-Partom Viscoplastic Model Parameters for Some Aluminum Alloys at Elevated Temperature
PublikacjaThe paper presents the identification process of inelastic (viscoplastic) properties for two aluminum alloys at a temperature of 120°C. The material parameters are calculated on the basis of uniaxial tension tests. Twelve tests at elevated temperature for each alloy have been performed—three tests for four different strain rates. The main purpose of the paper is to identify the Bodner-Partom viscoplastic model parameters for two...
-
Laboratory investigation with subbottom parametric echosounder SES-2000 standard with an emphasis on reflected pure signals analysis
PublikacjaThe main goal of the paper is to describe correlations between measurements results of trials taken on Gulf of Gdańsk bottom sounded with parametric echosounder SES-2000 Standard and laboratory research where collected during survey sediments were measured. Stationary tests took place at Gdansk University of Technology where 30 meters long 1.8 meter deep and 3 meters wide water tank is located. Main lobe of antenna was directed...
-
Rigid finite elements and multibody modeling in analyses of a robot shaped elastic/plastic deformations of a beam
PublikacjaDynamics analysis of a system composed of a parallel manipulator and of an elastic beam is presented in the paper. Classic 3RRR parallel manipulator is considered and used to deform the beam. Elasto-plastic deformations are investigated. Rigid-finite-elements technique is employed to deal with dynamics of the beam. A multibody structure is associated with the introduced hybrid system in order to model its dynamics. Idea of the...
-
CHARACTERIZATION STUDY ON MECHANICAL PROPERTIES OF POLYESTER COATED FABRIC
PublikacjaThe scope of the paper is to determine the mechanical properties of the Precontraint 1302 polyester coated fabric under uniaxial and biaxial tensile tests. The results are compared for Precontraint 1302 fabric and other types of coated fabrics. The author applied an orthotropic model and a dense net model to reflect the polyester coated fabric performance under uniaxial and biaxial tensile tests. Material parameters are specified...
-
PROPELLER INVESTIGATIONS BY MEANS OF NUMERICAL SIMULATION
PublikacjaThe analyses of hydroacoustics are of high interest at the moment due to strong impact of hydroacoustic phenomena on marine environment; the noises, generated e.g. by marine traffic, may be harmful for sea life. The analyses presented here are focused on one of main sources of noises generated by ships, i.e. cavitating propeller. The goal of the work is the assessment of the cavitation phenomenon, carried out with the standard...
-
Experience with instantiating an automated testing process in the context of incremental and evolutionary software development
PublikacjaThe purpose of this article is to present experiences from testing a complex AJAX-based Internet-system which is under development for more than five years. The development process follows incremental and evolutionary lifecycle model and the system is delivered in subsequent releases. Delivering a new release involves both, the new tests (related to the new and/or modified functionalities) and the regression tests (after their...
-
Timber-frame house resistant to dynamic loads - analysis of wall panel filled with polyurethane foam
PublikacjaThe present study shows the experimentally and numerically determined response of a single timber-frame house wall panel filled with polyurethane (PU) foam under dynamic loads. The harmonic tests were conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified displacement. Based on the results of the comparison between the experimental tests and the numerical analyses, the numerical...
-
Numerical Modelling for Prediction of Compression Index from Soil Index Properties in Jimma town, Ethiopia
PublikacjaIn this study, correlations are developed to predict compression index (Cc) from index parameters so that one can be able to model Jimma soils with compression index using simple laboratory tests. Undisturbed and disturbed soil samples from twelve different locations in Jimma town were collected. Laboratory tests like specific gravity, grain size analysis, Atterberg limit, and one-dimensional consolidation test for a total of twenty-four...
-
Results of the “DPDT-Auger” Research Project on Screw Displacement Piles
PublikacjaThe main objective of the “DPDT-Auger” research project was to test the prototype DPDT auger for forming screw displacement piles in the ground (patented in Poland in 2020). An additional aim was to develop design methods and rules for the making of such piles. The augers and piles were first tested on a model scale, and then more extensively in the real scale on experimental field plots. The results found the overall functionality...
-
Numerical Determination of the Load-Bearing Capacity of a Perforated Thin-Walled Beam in a Structural System with a Steel Grating
PublikacjaThis article presents the results of numerical simulations of a structural system consisting of steel perforated thin-walled beams and a steel grating. The simulations were conducted using the finite element method. The analysis took into account physical and geometric nonlinearity as well as the contact between the steel grating and the beams. The main goal of the research was to develop load-bearing curves for the main beam in...
-
Analysis of the Hydrodynamic Properties of the 3-Column Spar Platform for Offshore Wind Turbines
PublikacjaThe article presents a design of a floating platform for offshore wind turbines. The concept is a modification of the Spar design and consists of three variable section columns connected to each other by a ballast tank in the lower part of the platform. This solution makes it possible to influence the position of the centre of buoyancy and the centre of mass of the structure. Compared to the classic Spar platform structure, the...
-
Experimental dynamic study on a timber-frame house using shaking table
PublikacjaThe aim of this paper is to show the results of the shaking table experimental study concerning the behaviour of the model of the timber-frame house under earthquake excitation and impact loading. In order to determine the basic dynamic properties of the undamaged structure, the free vibration and the sweep-sine tests were first conducted. Then, the model was excited using the time history record of the El Centro earthquake of...
-
Laboratory Determination of Burger's Model Parameters for Visco-elastic Analysis of Road Pavement Materials
PublikacjaBurger's Model is one of those models that describes performance of asphalt mixtures. Its parameters can be used in road construction analysis based on visco-elastic properties in wide variety of temperatures using dedicated programs (e.g. Veroad) or in Finite Element Method (FEM). Parameters of Burger's Model can be used for example in prediction of low temperature cracking in low winter temperatures or permanent deformation...
-
ORF Approximation in Numerical Analysis of Fractional Point Kinetics and Heat Exchange Model of Nuclear Reactor
PublikacjaThis paper presents results concerning numerical solutions of the fractional point kinetics (FPK) and heat exchange (HE) model for a nuclear reactor. The model consists of a nonlinear system of fractional and ordinary differential equations. Two methods to solve the model are compared. The first one applies Oustaloup Recursive Filter (ORF) and the second one applies Refined Oustaloup Recursive Filter (RORF). Simulation tests have...
-
ORF Approximation in Numerical Analysis of Fractional Point Kinetics and Heat Exchange Model of Nuclear Reactor
PublikacjaThis paper presents results concerning numerical solutions of the fractional point kinetics (FPK) and heat exchange (HE) model for a nuclear reactor. The model consists of a nonlinear system of fractional and ordinary differential equations. Two methods to solve the model are compared. The first one applies Oustaloup Recursive Filter (ORF) and the second one applies Refined Oustaloup Recursive Filter (RORF). Simulation tests have...
-
A method to assess transverse vibration energy of ship propeller shaft for diagnostic purposes
PublikacjaThe article discusses a key problem of ship propulsion system vibration diagnostics, which concerns assessing this part of mechanical energy transmitted from the main engine to the ship propeller which is dissipated due to propeller shaft vibration. A simplified calculation model is proposed which allows the total energy of the generated torsional vibration to be assessed from the shaft deflection amplitude measured at the mind-span...
-
Possibilities of using SVC compensators for synchronous generators rotors oscillations damping.
PublikacjaThe article presents the idea of using static var compensators (SVC) for damping generators rotors oscillations. A novel SVC controller structure is proposed to provide better dynamic performance of the power system. A tests results are shown for proposed controller structure, that was carried out in a three-machine power system model as well as in multi-machine model of Polish Power System.
-
An observability and detectability analysis for non-linear uncertain CSTR model of biochemical processes
PublikacjaThe problem of proving observability/detectability properties for selected non-linear uncertain model of biochemical processes has been addressed in this paper. In particular, the analysis of observability/detectability in the face of parametric and unstructured uncertainty in system dynamics transformed into unknown inputs, and unknown initial conditions has been performed. Various sets of system measured outputs were taken into...
-
Validation Process for Computational Model of Full-Scale Segment for Design of Composite Footbridge
PublikacjaExperimental tests and numerical simulations of a full-scale segment of a foot and cycle bridge made of polymer composites are presented in the paper. The analysed structure is made of sandwich panels, which consist of glass fibre reinforced polymer (GFRP) multi-layered laminate faces and a PET foam (obtained from recycling) core. The dimensions of the segment cross-section are the same as for the target footbridge; however, span...
-
Failure mode prediction for composite structural insulated panels with MgO board facings
PublikacjaSandwich panels are readily used in civil engineering due to their high strength to weight ratio and the ease and speed of assembly. The idea of a sandwich section is to combine thin and durable facings with a light-weight core and the choice of materials used allows obtaining the desired behaviour. Panels in consideration consist of MgO (magnesium oxide) board facings and expanded polystyrene core and are characterized by immunity...
-
Hydraulic resistance analyses of selected elements of the prototype Stirling engine
PublikacjaThe paper presents the results of simulation tests of hydraulic resistance and temperature distribution of the prototype Stirling alpha engine supplied with waste heat. The following elements were analyzed: heater, regenerator and cooler. The engine uses compressed air as a working gas. Analyses were carried out for three working pressure values and different engine speeds. The work was carried out in order to optimize the configuration...