Wyszukiwarka
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: NUMERICAL ANALYSIS
-
Fiber optic microsphere with a ZnO thin film for potential application in a refractive index sensor – theoretical study
PublikacjaOptical fiber sensors of refractive index play an important role in analysis of biological and chemical samples. This work presents a theoretical investigation of spectral response of a fiber optic microsphere with a zinc oxide (ZnO) thin film deposited on the surface and evaluates the prospect of using such a structure for refractive index sensing. A microsphere is fabricated by an optical fiber tapering method on the base of...
-
The influence of stainless steels microstructure evolution on the mechanical properties of pressure installation elements
PublikacjaIn this paper results of FEM analysis performed for pipe and 90o elbow, made of super duplex stainless steel, after precipitation of sigma phase (),were presented. Heat treatment conditions simulate accidental overheating that can occur in nuclear installations after cooling circulation fails. For initial and modified microstructure tensile test was performed and numerical description of work hardening curves was done. Verification...
-
Testing the Effect of Bathymetric Data Reduction on the Shape of the Digital Bottom Model
PublikacjaDepth data and the digital bottom model created from it are very important in the inland and coastal water zones studies and research. The paper undertakes the subject of bathymetric data processing using reduction methods and examines the impact of data reduction according to the resulting representations of the bottom surface in the form of numerical bottom models. Data reduction is an approach that is meant to reduce the size...
-
Macromodels for Efficient Analysis of Open-Region Problems Using the Finite Element Method
PublikacjaThis paper presents a local model-order reduction, called macromodeling, applied to speed-up the simulations of open-region problems, analyzed by means of finite element method. This technique is illustrated by a numerical example, which deals with a dielectric resonator antenna (DRA). The obtained results show that the proposed approach is reliable and can significantly increase the standard finite element method efficiency.
-
Dynamic Research of Masonry Vault in a Technical Scale
PublikacjaThe paper presents preliminary results of dynamic tests of the masonry barrel vault in a technical scale. Experimental studies are intended to identify material properties of homogenized masonry vaults under dynamic loads. The aim of the work is to create numerical models to analyse vault’s dynamic response to dynamic loads in a simplest and accurate way. The process of building the vault in a technical scale is presented in the...
-
Revisiting Toroidal Dipolar Moment in Planar Metamaterial
PublikacjaThis article revisits the electric, magnetic, and toroidal dipolar moments in the metamaterial structure and presents the flatland design for generating a toroidal dipolar response for the electromagnetic plane wave at normal incidence. Based on the numerical analysis of the surface current, the electric field, the magnetic field, and the quantitative analysis of scattered power supported by the electromagnetic multipole theory,...
-
A selectively reduced degree basis for efficient mixed nonlinear isogeometric beam formulations with extensible directors
PublikacjaThe effect of higher order continuity in the solution field by using NURBS basis function in isogeometric analysis (IGA) is investigated for an efficient mixed finite element formulation for elastostatic beams. It is based on the Hu–Washizu variational principle considering geometrical and material nonlinearities. Here we present a reduced degree of basis functions for the additional fields of the stress resultants and strains...
-
An analytical four-layer horizontal electric current dipole model for analysing underwater electric potential in shallow seawater
PublikacjaThe paper presents a new analytical four‑layer (air–water–bottom–non‑conductive layer) horizontal electric dipole model which allows an accurate approximation of ship’s Underwater Electric Potential (UEP) from a sufficient depth in shallow coastal marine waters. The numerical methods, usually Finite Element Method (FEM) or Boundary Elements Method (BEM), are typically used to estimate the electric field and the distribution of...
-
Analysis of the incompressibility constraint in the smoothed particle hydrodynamics method
Publikacja -
Artur Piekarczuk dr hab. inż. prof. ITB
OsobyMy professional activity includes issues related to the examination and evaluation of construction products and the preparation of academic, technical and expert opinions on building construction structures as well as scientific articles in the field of buildings. My interests were focused on the use of modern methods of numerical analysis in research and expert works. I am currently the Manager of the Durability Testing Laboratory...
-
A Proposed Machine Learning Model for Forecasting Impact of Traffic-Induced Vibrations on Buildings
PublikacjaTraffic-induced vibrations may cause various damages to buildings located near the road, including cracking of plaster, cracks in load-bearing elements or even collapse of the whole structure. Measurements of vibrations of real buildings are costly and laborious. Therefore the aim of the research is to propose the original numerical algorithm which allows us to predict, with high probability, the nega-tive dynamic impact of traffic-induced...
-
DETECTION OF DEBONDING IN STEEL BARS EMBEDDED IN CONCRETE USING GUIDED WAVE PROPAGATION
PublikacjaThe paper presents a non-destructive diagnostic technique based on guided wave propagation phenomenon used to assess the adhesive bonding between a steel bar and a concrete cover. Double-layered cylindrical specimens with different levels of debonding and its location were investigated. The influence of bonding length on the excitation of multiple modes of longitudinal guided waves was analysed. Numerical simulations of guided...
-
Experimentation, material modelling and simulation of bonded joints with a flexible adhesive
PublikacjaThe paper deals with material parameters identification of a flexible adhesive and the numerical simulation of its behaviour in a single lap bonded joint. The material modelling was based on the simple shear and tensile-shear laboratory tests of the bonded joints made of thin aluminium and polyurethane plates with the flexible adhesive Terostat MS 9360 manufactured by Henkel AG & Co. The adhesive was considered as a hyperelastic...
-
Convergence of rational multistep methods of of Adams-Padé type
PublikacjaRational generalizations of multistep schemes, where the linear stiff part of a given problem is treated by an A-stable rational approximation, have been proposed by several authors, but a reasonable convergence analysis for stiff problems has not been provided so far. In this paper we directly relate this approach to exponential multistep methods, a subclass of the increasingly popular class of exponential integrators. This natural,...
-
Stability of softly switched multiregional dynamic output controllers with a static antiwindup filter: A discrete-time case
PublikacjaThis paper addresses the problem of model-based global stability analysis of discrete-time Takagi–Sugeno multiregional dynamic output controllers with static antiwindup filters. The presented analyses are reduced to the problem of a feasibility study of the Linear Matrix Inequalities (LMIs), derived based on Lyapunov stability theory. Two sets of LMIs are considered candidate derived from the classical common quadratic Lyapunov...
-
Quantum strategies for rendezvous and domination tasks on graphs with mobile agents
PublikacjaThis paper explores the application of quantum nonlocality, a renowned and unique phenomenon acknowledged as a valuable resource. Focusing on an alternative application, we demonstrate its quantum advantage for mobile agents engaged in specific distributed tasks without communication. The research addresses the significant challenge of rendezvous on graphs and introduces a distributed task for mobile agents grounded in the graph...
-
Collective citizens' behavior modelling with support of the Internet of Things and Big Data
PublikacjaIn this paper, collective human behaviors are modelled by a development of Big Data mining related to the Internet of Things. Some studies under MapReduce architectures have been carried out to improve an efficiency of Big Data mining. Intelligent agents in data mining have been analyzed for smart city systems, as well as data mining has been described by genetic programming. Furthermore, artificial neural networks have been discussed...
-
Complex Root Finding Algorithm Based on Delaunay Triangulation
PublikacjaA simple and flexible algorithm for finding zeros of a complex function is presented. An arbitrary-shaped search region can be considered and a very wide class of functions can be analyzed, including those containing singular points or even branch cuts. The proposed technique is based on sampling the function at nodes of a regular or a self-adaptive mesh and on the analysis of the function sign changes. As a result, a set of candidate points...
-
DYNAMIC ANALYSIS OF THE IMPACT OF VIBRATION ON HISTORICAL BUILDINGS - AN OWN PROJECT OF EXTERNAL STAIRCASE
PublikacjaThis article presents numerical simulations that concern modeling of interaction of the external staircase’s construction with the observation deck on historic water tower located at Gdansk University of Technology. The interaction occurring according to various methods of the staircase's construction support on the wall of the historic tower was compared. The external staircase that allows for entering onto the monument was subjected...
-
On the non-linear dynamics of torus-shaped and cylindrical shell structures
PublikacjaIn this study, the non-linear dynamic analysis of torus-shaped and cylindrical shell-like structures has been studied. The applied material is assumed as the functionally graded material (FGM). The structures are considered to be used for important machines such as wind turbines. The effects of some environmental factors on the analysis like temperature and humidity have been considered. The strain field has been calculated in...
-
Mariusz Figurski prof. dr hab. inż.
OsobyDyrektor Centrum Modelowania Meteorologicznego Instytut Meteorologii i Gospodarki Wodnej - Państwowy Instytut Badawczy. Urodził się 27 kwietnia 1964 roku w Łasinie. Egzamin maturalny złożył w 1983 roku po ukończeniu II Liceum Ogólnokształcącego im. Jana III Sobieskiego w Grudziądzu, Studia wyższe w trybie indywidualnym ukończył w 1989 (10.07.1989) na Wydziałach Elektromechanicznym i Inżynierii Lądowej i Geodezji Wojskowej Akademii...
-
Inverse Analysis as a Key Element of Safety Assessment under the Snow Load For The Large Suspension Roofs Structure
PublikacjaThe paper presents a concept and realization of monitoring system for the Silesian Stadium in Chorzow. The idea of the system lies in fusion of structure monitoring with a calibrated numerical FEM model [1]. The inverse problem is solved. On the base of measured selected displacements, the numerical FEM model of the structure combined with iterative method, develops the current snow load distribution. Knowing the load, we can calculate...
-
Quantitative assessment of the influence of tensile softening of concrete in beams under bending by numerical simulations with XFEM and cohesive cracks
PublikacjaResults of the numerical simulations of the size effect phenomenon for concrete in comparison with experimental data are presented. In-plane geometrically similar notched and unnotched beams under three-point bending are analyzed. EXtended Finite Element Method (XFEM) with a cohesive softening law is used. Comprehensive parametric study with the respect to the tensile strength and the initial fracture energy is performed. Sensitivity...
-
Numerical Study on Seismic Response of a High-Rise RC Irregular Residential Building Considering Soil-Structure Interaction
Publikacja -
Experimental and numerical investigation of crosstalk effect in coupled coplanar waveguides - part II: Multimode coupled line representation
PublikacjaW pracy przedstawiono metodę analizy nieidealności połączenia poszczegółnych fragmentów rozłożonego ekranu na zjawisko przesłuchu w strukturze sprzężonych falowodów koplanarnych z uziemionym centralnym paskiem. Analiza bierze pod uwagę efekty dyspersji oraz wielorodzajową naturę rozchodzenia się fali elektromagnetycznej w strukturze wieloprzewodowej. Teorię zweryfikowano praktycznie uzyskując bardzo dobrą zgodność pomiędzy wynikami...
-
Direct measurements and numerical predictions of welding-induced initial deformations in a full-scale steel stiffened plate structure
Publikacja -
Identification of filtration and migration parameters in the MATLAB calculation environment using numerical simulation of breakthrough curve and optimization methods
Publikacja -
Investigation of the flow, heat and mass transfer and emissions in pulverized fuel fired boiler using physical and numerical modeling.
PublikacjaPraca przedstawia wykorzystanie techniki modelowania fizycznego trójwymiarowego oraz obliczeń numerycznych umożliwiających symulację rzeczywistych procesów spalania paliw stałych i gazowych w urządzeniach energetycznych. Dodatkowo wyniki obliczeń porównano z wynikami modelowania fizycznego oraz pomiarów na obiekcie rzeczywistym.
-
Comparison the heat load as the results of tests on human subject in a hot environment with the results obtained from numerical simulation
Publikacja -
Determination of Thermophysical Parameters Involved in The Numerical Model to Predict the Temperature Field of Cast-In-Place Concrete Bridge Deck
PublikacjaThe paper dealswith a concept of a practical computationmethod to simulate the temperature distribution in an extradosed bridge deck. The main goal of the study is to develop a feasible model of hardening of concrete consistent with in-situ measurement capabilities. The presented investigations include laboratory tests of high performance concrete, measurements of temperature evolution in the bridge deck and above all, numerical...
-
Temperature, velocity and mean turbulence structure in strongly heated internal gas flows. Comparison of numerical predictions with data
PublikacjaW pracy przedstawiono symulacje numeryczne przy użyciu szeregu modeli turbulencji celem analizy silnie ogrzewanego przepływu powietrza w pionowych rurach. Obliczenia porównano z danymi eksperymentalnymi. Analizowano modyfikacje pola prędkości, temperatury i turbulencji. W rozpatrywanych warunkach odnotowano silną wrażliwość obliczeń na silnie zmieniające się pole temperatury. Stwierdzono, że analizowane przypadki najlepiej odzwierciedla...
-
The experimental and numerical investigation of fracture behaviour in PMMA notched specimens under biaxial loading conditions – Tension with torsion
PublikacjaThis paper presents the results of experimental fracture test of flat PMMA specimens under biaxial loading condition tension with torsion (proportional). The specimens were made in two thicknesses: 5 and 15 mm and were weakened with V-type edge notches with different root radii: 0.5; 2 and 10 mm. Thanks to the ARAMIS 3D 4 M non-contact vision system, measurement of the elongation and twist angle were recorded. During experimental...
-
Experimental study and numerical simulation on porosity dependent direct reducibility of high-grade iron oxide pellets in hydrogen
PublikacjaThe transition to more environmentally friendly steel production methods has intensified research into hydrogen-based direct reduction (HyDR) of iron oxide pellets. The aim of this study is to systematically investigate the kinetics of the reduction process, the evolution of porosity and the resulting microstructural changes on the reduction behavior of high-quality pellets during HyDR of iron ore at different temperatures. A modified...
-
Assessment of thermal and electrical performance of flat plate air-cooled photovoltaic roof tile – experimental and numerical studies
PublikacjaThe current state of development of the solar energy sector necessitates a new form of incentive for entities to invest in photovoltaic (PV) installations. Building-integrated photovoltaic/thermal (BIPV/T) systems are gaining increasing interest. Effective methods for heat recovery from BIPV/T collectors are searched for. Presented research experimentally and numerically considered the influence of cooling conditions on the electrical...
-
Controlling nodal displacement of pantographic structures using matrix condensation and interior-point optimization: A numerical and experimental study
PublikacjaThis study presents an innovative approach for the precise control of nodal displacements in pantographic structures. The method is founded on the Matrix Condensation of Force Method, seamlessly integrated with an Interior Point Optimization algorithm. This combination offers a unique advantage by allowing users to manipulate displaced nodes within a defined coordination domain. Furthermore, this approach introduces the Interior...
-
Initial Report on Numerical Modeling of Blood Flow in Myocardial Bridge Region of Coronary Artery: Concept of Model Validation
PublikacjaThe paper presents a numerical method of blood flow simulation within the coronary artery covered by the myocardial bridge. The myocardial bridge is a congenital coronary abnormality caused by the blood vessel location under one of the heart muscles. In this case, the blood flow within the vessel is partially disturbed which can cause several consequences. The presented numerical simulation allowed us to estimate the blood flow...
-
Reliable Greedy Multipoint Model-Order Reduction Techniques for Finite-Element Analysis
PublikacjaA new greedy multipoint model-order reduction algorithm for fast frequency-domain finite-element method simulations of electromagnetic problems is proposed. The location of the expansion points and the size of the projection basis are determined based on a rigorous error estimator. Compared to previous multipoint methods, the quality of the error estimator is significantly improved by ensuring the orthogonality of the projection...
-
Electromagnetic Simulation with 3D FEM for Design Automation in 5G Era
PublikacjaElectromagnetic simulation and electronic design automation (EDA) play an important role in the design of 5G antennas and radio chips. The simulation challenges include electromagnetic effects and long simulation time and this paper focuses on simulation software based on finite-element method (FEM). The state-of-the-art EDA software using novel computational techniques based on FEM can not only accelerate numerical analysis, but...
-
Backscattering properties of southern Baltic herring
PublikacjaReliable TS(L) relationship is required to improve acoustic algorithms of abundanceestimation of Baltic herring. The relationships, empirically obtained in different parts of theBaltic Sea, produce up to 8 dB – difference in the herring TS. In order to develop an accurateTS(L) relationship, it is important to analyze factors controlling the TS variability. Thepossible impact of the regional difference...
-
A Concept of Thermal Effort for Heat-Induced Metal Plasticity
PublikacjaThis paper proposes a new concept of material effort that considers heat-induced plasticity for heat-resistant steels. These steels indicate a strength differential effect, a stress shearness effect, pressure sensitivity, and other features. Therefore, a three-parameter, temperature-dependent yield function was presented and, next, analytically and geometrically researched. To validate the accuracy of the formulated yield function,...
-
Analiza wrażliwości tarczy z wykorzystaniem metody elementów skończonych
PublikacjaW pracy przedstawiono przykład zastosowania analizy wrażliwości tarczy modelowanej przy pomocy metody elementów skończonych. Podstawy teoretyczne oraz przykład numeryczny dotyczą wpływu różnicowania grubości całej tarczy oraz jej obszarów – jako zmiennej pro-jektowej – na przemieszczenie wybranego punktu – jako zmiennej stanu.
-
Behaviour of Asymmetric Structure with Base Isolation Made of Polymeric Bearings
PublikacjaEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Seismic excitations cause a lot of damage in a wide variety of ways, leaving thousands of casualties in their wake. Due to randomness of earthquake occurrence, lack of visible causes and their power of destructiveness, structural engineers need to develop new technical solutions and protection systems against...
-
Contemporary Architectural Design in the Context of Historic Remains: The Case of the Old City of Gdańsk
PublikacjaThis article presents several examples of modern developments designed to preserve and coexist with fragments of historic brick buildings. These building projects each faced a similar task; to save and display the historical urban fabric, but they differed significantly in how they chose to achieve that goal. Not all of the projects presented in this study meet the requirements of the Venice Charter equally well. In this field,...
-
Increase of power and efficiency of the 900 MW supercritical power plant through incorporation of the ORC
PublikacjaThe objective of the paper is to analyse thermodynamical and operational parameters of the supercritical power plant with reference conditions as well as following the introduction of the hybrid system incorporating ORC. In ORC the upper heat source is a stream of hot water from the system of heat recovery having temperature of 90 °C, which is additionally aided by heat from the bleeds of the steam turbine. Thermodynamical analysis...
-
Stability of a truss under upward wind loading
PublikacjaThe present paper is devoted to the numerical investigations of stability of a truss under upward wind load. The truss is braced at its the upper cord. A structural variant including lateral braces, or lateral and torsional braces is considered. The research presents the problems of linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity are presented. The initial...
-
GPU-Accelerated 3D Mesh Deformation for Optimization Based on the Finite Element Method
PublikacjaThis paper discusses a strategy for speeding up the mesh deformation process in the design-byoptimization of high-frequency components involving electromagnetic field simulations using the 3D finite element method (FEM). The mesh deformation is assumed to be described by a linear elasticity model of a rigid body; therefore, each time the shape of the device is changed, an auxiliary elasticity finite-element problem must be solved....
-
TRUSS JOINT WITH POSITIVE ECCENTRICITY EXPERIMENTAL RESEARCH
PublikacjaDue to the technological reasons in modern lightweight steel trusses, fabricated from cold- formed sections, positive eccentricities appear in the truss nodes what induce additional forces in the truss chords. To account for the real load-carrying capacity of truss node area the steel structure research in scale 1:1 were conducted. The experiments consisted of two parts: preliminary and proper one, when conclusions from...
-
Study on 19th-century cast iron columns from the former financial office building in Kwidzyn
PublikacjaThe article presents the results for cast iron columns used as floor supports in the former financial office building in Kwidzyn (Poland).The stocktaking drawings provided the general and detailed data about the 19th century designer’s decisions. During the research, architectural and structural analysis was carried out. The graphics were used as a starting material for preparing 3D calculation models. The FEM-based numerical simulations...
-
An Innovative Floating System with a Savonius Rotor as a Horizontal-Axis Wind Turbine
PublikacjaIn this project, an innovative wind turbine was designed for a floating plant. A large Savonius rotor was replaced with a double-rotor wind turbine implemented as a horizontal-axis turbine. This double rotor was positioned on the tip of a thrust plate and fixed to the deck of a catamaran. Simple 2D numerical simulations were performed to confirm the effectiveness of the concept. An analysis of the floating system configuration...
-
Torsion of restrained thin-walled bars of open constant bisymmetric cross-section
PublikacjaElastic and geometric stiffness matrices were derived using Castigliano's first theorem, for the case of torsion of restrained thin-walled bars of open constant bisymmetric cross-section. Functions which describe the angles of torsion were adopted from the solutions of thedifferential equation for restrained torsion. The exact solutions were simplified by expanding them in a power series. Numerical examples were taken from Kujawa...