Wyszukiwarka
Filtry
wszystkich: 530
Wyniki wyszukiwania dla: HYDROGEN TRANSPORT
-
Dynamic characteristics of the proton exchange membrane fuel cell module
PublikacjaThe paper describes a fuel cell based system and its performance. The system is based on two fuel cell units, DC/DC converter, DC/AC inverter, microprocessor control unit, load unit, bottled hydrogen supply system and a set of measurement instruments. In the study presented in the paper a dynamic response of the proton exchange membrane (PEM) fuel cell system to unit step change load as well as to periodical load changing cycles...
-
Relativistic two-dimensional hydrogen-like atom in a weak magnetic field
PublikacjaA two-dimensional (2D) hydrogen-like atom with a relativistic Dirac electron, placed in a weak, static, uniform magnetic field perpendicular to the atomic plane, is considered. Closed forms of the first- and second-order Zeeman corrections to energy levels are calculated analytically, within the framework of the Rayleigh–Schrödinger perturbation theory, for an arbitrary electronic bound state. The second-order calculations are...
-
Synthesis and properties of porous Sr 0.96 Y 0.04 Ti 1−x Nb x O 3
PublikacjaA series of porous, single phase Sr0.96Y0.04Ti1-xNbxO3 samples was obtained using a wet synthesis method (modified citrate sol-gel) method. Temperature-programmed reduction (TPR) and temperature-programmed oxidation (TPO) measurements have shown high stability of the obtained material in variable (oxidizing/reducing) atmospheres. All samples exhibit high conductivity in hydrogen atmosphere with the highest value (around 1S/cm)...
-
Charge-based deep level transient spectroscopy of B-doped and undoped polycrystalline diamond films
PublikacjaThe undoped and B-doped polycrystalline diamond thin film was synthesized by hot filament chemical vapor deposition and microwave plasma, respectively. The structural characterization was performed by scanning electron microscopy, X-ray diffraction and Raman spectroscopy. The electrical properties of synthesized diamond layer were characterized by dc-conductivity method and charge deep level transient spectroscopy. The B-doped...
-
Novel method for metal-oxide glass composite fabrication for use in thermoelectric devices
PublikacjaA novel method for thermoelectric materials fabrication using a reduction of oxide precursors in hydrogen was reported. On the example of Bi-Sb, Bi-Sb-Te and Te-Ag-Ge-Sb compounds it was shown that this simple and easy method is suitable for fabrication of two-, three- and even multicomponent thermoelectric materials. It allows controlling a composition, microstructure and even type a of electrical charge carriers. As a result...
-
ortho-Fluorobenzanilides and ortho-fluorothiobenzanilides: Molecular conformations and crystal packing
PublikacjaSeries of 2-fluoro and 2,6-difluorobenzanilides and their thiobenzanilide analogs have been synthesized to investigate the influence of the fluorine atom on their crystal structures and self-assembly in the crystal lattice. The X-ray analysis of the single crystal revealed that the synthesized molecules adopt a geometry being deflected from planarity. The deflection was investigated by analysis of dihedral angles between mean planes...
-
Pyrolysis of RDF and Catalytic Decomposition of the Produced Tar in a Char Bed Secondary Reactor as an Efficient Source of Syngas
PublikacjaOne of the technical limitations of refuse-derived fuel (RDF) pyrolysis is the high content of tar in its gas products. In order to resolve this problem, a two-stage RDF pyrolysis with a catalyst based on char from RDF pyrolysis is proposed. This paper presents the results of municipal waste pyrolysis beginning in an oven heated to 480 °C and ending with catalytic tar cracking carried out in the temperature range from 800 to 1000...
-
HYDROGEN PRODUCTION PERFORMANCE IN THERMOCATALYTIC REACTOR BASED ON THE INTERMETALLIC PHASE OF NI3AL
PublikacjaThe main aim of the following paper is mathematical modelling for momentum, heat and mass transfer, which is accompanied by chemical surface reactions of the flow of the mixture helium and methanol. The thermocatalytic devices used for decomposition of hydrocarbons incorporate vertical microchannels coupling at the ends and heated to 500 oC at the walls. The results of the experiment were compared with CFD calculations to calibrate...
-
A study of a reduction of a micro- and nanometric bismuth oxide in hydrogen atmosphere
PublikacjaA reduction of bismuth oxide in hydrogen atmosphere was investigated. The reaction was performed with a material in various structural forms: powder: with micrometric grains, powder with nanometric grains and powder pressed into pellets. The process was performed in both isothermal and non-isothermal conditions. An activation energy of the reaction calculated with Friedman method was found to be about 85 kJ/mol for the reduction...
-
Diiodo-BODIPY Sensitizing of the [Mo3S13]2– Cluster for Noble-Metal-Free Visible-Light-Driven Hydrogen Evolution within a Polyampholytic Matrix
PublikacjaWe report on a photocatalytic setup that utilizes the organic photosensitizer (PS) diiodo-BODIPY and the non-precious-metal-based hydrogen evolution reaction (HER) catalyst (NH4)2[Mo3S13] together with a polyampholytic unimolecular matrix poly(dehydroalanine)-graft-poly(ethyleneglycol) (PDha-g-PEG) in aqueous media. The system shows exceptionally high performance with turnover numbers (TON > 7300) and turnover frequencies (TOF...
-
Structure and thermoelectric properties of nickel-doped copper selenide synthesised in a hydrogen atmosphere
PublikacjaNickel-doped copper selenide—Cu2-xNixSe (x = 0; 0.01; 0.02; 0.03)—materials with high thermoelectric properties were synthesised through reduction of reagents in hydrogen. The impact of the nickel content on both the microstructure and thermoelectric properties was examined. The nickel-doped samples’ microstructure differed significantly from pristine copper selenide. Besides Cu2Se, copper precipitations were present in the materials....
-
Gasification of Densified Biomass (DB) and Municipal Solid Wastes (MSW) Using HTA/SG Technology
PublikacjaThe necessity of economical and rational use of natural energy sources caused a rapid development of research on the possibilities of using non‐conventional energy resources. Taking the above into account, a new technological process of thermochemical conversion of biomass and communal waste, commonly known as High Temperature Air/Steam Gasification (HTA/SG) and Multi‐Staged Enthalpy Extraction Technology (HTAG‐MEET), was developed....
-
Hydrogen direct reduction and reoxidation behaviour of high-grade pellets
PublikacjaHigh grade pellets with basicity index close to 0.5 were directly reduced in pure hydrogen atmosphere. The reduction experiments were performed in the temperature range 800 e1000 C at the pressure of 8 bar. The pellets internal structure was analysed through micro tomography observations in the unreduced and reduced conditions. After reduction, the pellets showed a variation of porosity up to more than 15% with a remarkable change...
-
Carboxylation Enhances Fragmentation of Furan upon Resonant Electron Attachment
PublikacjaWe report a dissociative electron attachment study to 2-furoic acid (C5H4O3) isolated in a gas phase, which is a model molecule consisting of a carboxylic group and a furan ring. Dissociation of furan by low energy electrons is accessible only via electronic excited Feshbach resonances at energies of incident electrons above 5 eV. On the other hand, carboxylic acids are well- known to dissociate via attachment of electrons at subexcitation energies....
-
Influence of chemical structure on physicochemical properties and thermal decomposition of the fully bio-based poly(propylene succinate-co-butylene succinate)s
PublikacjaIn this work, two polyesters and four copolyesters were studied. All materials were synthesized to obtain the monomers dedicated for thermoplastic polyurethane elastomers. For this type of PUR, the monomers should characterize by appropriate selected physicochemical properties and macromolecular structure distribution, which depends on synthesis conditions. The study of chemical structure with extensive and knowledgeable analysis...
-
Structural and catalytic properties of ceria layers doped with transition metals for SOFCs fueled by biogas
PublikacjaThe aim of this paper was to investigate an influence of the nanocrystalline Ce0.8A0.2O2-δ (A = Mn, Fe, Co, Ni, Cu) materials on the direct internal reforming of biogas in SOFC. Structural analysis of fabricated compounds has been done. An in-situ analysis of a composition of outlet gases from operating SOFC was performed using FTIR spectroscopy with simultaneous electrical tests. It was found out, that type of dopant strongly...
-
The effect of ionic liquids on the surface and photocatalytic properties of semiconducting materials
PublikacjaSemiconductor-mediated photocatalysis represents an environmentally friendly technology that could be used for the degradation of different pollutants in the gas and aqueous phases, for hydrogen generation, and for CO2-to-valuable product transformation reactions. Therefore, it is extremely important to accurately design a photocatalyst with the relevant features. In recent years, ionic liquids have often been employed as reagents...
-
Investigation of H2:CH4 plasma composition by means of spatially resolved optical spectroscopy
PublikacjaThe system based on spatially resolved optical emission spectroscopy dedicated for in situ diagnostics of plasma assisted CVD processes is presented in this paper. Measurement system coupled with chemical vapour deposition chamber by dedicated fiber-optic paths enables investigation of spatial distribution of species densities (Hx, H+, CH, CH+) during chemical vapour deposition process. Experiments were performed for a various...
-
Chromogenic amides of pyridine-2,6-dicarboxylic acid as anion receptors
PublikacjaThe synthesis of simple, chromogenic pyridine-2,6-dicarboxylic acid amides, derivates of isomeric nitroanilines and aminonitrophenols, and their ion binding properties are described. The ligands' response to ionic species was examined by naked eye and was studied with the use of UV-Vis spectroscopy in DMSO and its mixture with water. The effect of the localisation and the type of the substituents in aromatic rings were discussed....
-
Superexcited states in the vacuum-ultraviolet photofragmentation of isoxazole molecules
PublikacjaThe photofragmentation of isoxazole molecules producing excited atomic and molecular fragments has been investigated over the energy range 16-50 eV, using photon-induced fluorescence spectroscopy. The following fragments have been identified by their fluorescence: the excited hydrogen atoms H(n), n = 3-7 and the diatomic CH(A2Δ, B2Σ−), CN(B2Σ+) and C2(d3Πg) fragments. The diatomic fragments are vibrationally and highly rotationally...
-
Conversion of Biomass and Municipal Wastes into Syngas and Hydrogen using Highly Preheated Agent (HTAG)
PublikacjaGasification is considered to be one of the most promising energy recovery technologies for the widespread utilization of biomass and wastes. During this process raw feedstock is converted into a combustible gas, which can then be burnt to produce thermal energy, or to run engines for mechanical or electrical power. The studies of biomass gasification demonstrate it as a friendly alternative to fossil fuels as one of renewable...
-
Time evolution of Electrochemical Impedance spectra of cathodically protected steel in artificial seawater
PublikacjaUsability of Electrochemical Impedance Spectroscopy data for better cathodic protection control was investigated. Carbon steel – S235JR2 grade specimen were exposed in artificial seawater environment. Samples were polarized and their potentials corresponded to four different cathodic protection degrees. Time evolution of Electrochemical Impedance spectra was investigated. Goodness of fit function (X2) was analysed in terms of proper...
-
<i>N,N,N</i>-Trimethyl-N-(methyl 5-deoxy-2,3-<i>O</i>-isopropylidene-β-D-ribofuranosid-5- yl)ammonium 4-methylbenzenesulfonate sesquihydrate.
PublikacjaThe structure of the title compound, [C12H24NO4][C7H7O3S]·1.5H2O, contains alternating layers parallel to (001) of hydrophobic and polar character, stabilized by C-H...O hydrogen bonding. The furan ring adopts an envelope conformation with the C(OMe) atom as the flap, and the dioxolane ring is twisted about one of the O-C(methine) bonds. A comparison to related compounds is presented. The tosylate-O atoms were disordered over two...
-
Fabrication, Microstructure and High Temperature Corrosion Resistance of Porous Alloys for Solid Oxide Fuel Cells
PublikacjaPorous alloys find use in modern Solid Oxide Fuel Cells as the supporting structures. As they are exposed to high temperatures (> 500°C) an oxide scale forms on their surface due to high temperature corrosion phenomena. Since the ratio between the surface area and volume is much higher than for planar samples, formation of the oxide can lead to a breakaway oxidation after relatively short times. Therefore corrosion properties of...
-
Bis(ammonium) Zoledronate Dihydrate
PublikacjaNeutralization of 2-(1-imidazole)-1-hydroxyl-1,1`-ethylidenediphosphonic acid (zoledronic acid) by an excess of ammonia yielded bis(ammonium) zoledronate dihydrate, {C5H8N2O7P2 2−, 2(H4N+), 2(H2O)}. The product is readily soluble in water and forms monocrystals for which the X-ray structural analysis was carried out. The zoledronic anion is of double negative charge due to deprotonation of three P–OH groups and protonation of the...
-
Features extraction from the electrocatalytic gas sensor responses
PublikacjaOne of the types of gas sensors used for detection and identification of toxic-air pollutant is an electrocatalytic gas sensor. The electrocatalytic sensors are working in cyclic voltammetry mode, enable detection of various gases. Their response are in the form of I-V curves which contain information about the type and the concentration of measured volatile compound. However,...
-
Positron scattering on molecular hydrogen: Analysis of experimental and theoretical uncertainties
PublikacjaExperiments performed in recent years on positron scattering from molecular hydrogen indicated a rise of the total cross section in the limit of zero energy, but essentially disagree on the amplitude of this rise. Mitroy and collaborators [J.-Y. Zhang et al., Phys. Rev. Lett. 103, 223202 (2009)] predicted a scattering length somewhat different from values deduced experimentally. Using a Markov chain Monte Carlo modified effective...
-
Structure and thermoelectric properties of Bi–Te alloys obtained by novel method of oxide substrates reduction
PublikacjaA novel method of thermoelectric materials fabrication has been developed. Oxide reagents have been melted at high temperature in air, quenched, milled to powder and reduced in hydrogen to form Bi–Te alloys. Structural and thermoelectric properties of samples have been investigated depending on initial composition and temperature of reduction process. Sample 25Bi2O3–75TeO2 reduced at 340 °C for 10 h has been found to be a p-type...
-
Mathematical modeling of hydrogen production performance in thermocatalytic reactor based on the intermetallic phase of Ni3Al
PublikacjaThe main goal of the following work is to adjust mathematical modelling for mass transfer, to specific conditions resulting from presence of chemical surface reactions in the flow of the mixture consisting of helium and methanol. The thermocatalytic devices used for decomposition of organic compounds incorporate microchannels coupled at the ends and heated to 500 oC at the walls regions. The results of the experiment were compared...
-
Thermochemical Conversion of Biomass and Municipal Waste into Useful Energy Using Advanced HiTAG/HiTSG Technology
PublikacjaAn advanced thermal conversion system involving high-temperature gasification of biomass and municipal waste into biofuel, syngas or hydrogen-rich gas is presented in this paper. The decomposition of solid biomass and wastes by gasification is carried out experimentally with a modern and innovative regenerator and updraft continuous gasifier, among others. A ceramic high-cycle regenerator provides extra energy for the thermal conversion...
-
Green adsorbents and solvents in food analysis
PublikacjaGreen analytical chemistry aims to minimize the negative impact of analytical procedures on the environment and human health. This can be achieved through the use of non-toxic and environmentally friendly reagents. Classical green solvents include water, ethanol, acetone, and supercritical fluids. Water has been used for the extraction of water-soluble compounds (sugars, amino acids). Ethanol and acetone have been used for the...
-
Deep eutectic solvent-based shaking-assisted extraction for determination of bioactive compounds from Norway spruce roots
PublikacjaPolyphenolic compounds play an essential role in plant growth, reproduction, and defense mechanisms against pathogens and environmental stresses. Extracting these compounds is the initial step in assessing phytochemical changes, where the choice of extraction method significantly influences the extracted analytes. However, due to environmental factors, analyzing numerous samples is necessary for statistically significant results,...
-
Cathodic Activation of Titania-Fly Ash Cenospheres for Efficient Electrochemical Hydrogen Production: A Proposed Solution to Treat Fly Ash Waste
PublikacjaFly ash (FA) is a waste product generated in huge amounts by coal-fired electric and steam-generating plants. As a result, the use of FA alone or in conjunction with other materials is an intriguing study topic worth exploring. Herein, we used FA waste in conjunction with titanium oxide (TiO2) to create (FA-TiO2) nanocomposites. For the first time, a cathodic polarization pre-treatment regime was applied to such nanocomposites...
-
Furan Fragmentation in the Gas Phase: New Insights from Statistical and Molecular Dynamics Calculations
PublikacjaWe present a complete exploration of the different fragmentation mechanisms of furan (C4H4O) operating at low and high energies. Three different theoretical approaches are combined to determine the structure of all possible reaction intermediates, many of them not described in previous studies, and a large number of pathways involving three types of fundamental elementary mechanisms: isomerization, fragmentation, and H/H2 loss...
-
Dissociation and fragmentation of furan by electron impact
PublikacjaDissociation and fragmentation processes that produce electronically excited atomic and molecular fragments, following electron impact excitation, have been studied in furan. The optical excitation technique has been employed over the electron incident energy range 15-95 eV. Formation of excited hydrogen atoms H(n) in the n = 4-10 states has been detected by observation of the Balmer series. The diatomic CH fragments are formed...
-
Rozdział 10.2 Metody oznaczania właściwości przeciwutleniających próbek żywności
PublikacjaWystępowanie większości chorób cywilizacyjnych może być rezultatem stresu oksydacyjnego prowadzącego do różnorodnych zmian w ludzkim organizmie, wywołanych działaniem tzw. reaktywnych form tlenu. Z tego też powodu pojawiło się olbrzymie zapotrzebowanie na szybkie testy umożliwiające pomiar całkowitej zawartości przeciwutleniaczy czy też ogólnej siły przeciwutleniającej produktów żywnościowych a w szczególności świeżych warzyw...
-
Spatial characterization of H 2: CH 4 dissociation level in microwave ECR plasma source by fibre-optic OES
PublikacjaSpatially resolved optical emission spectroscopy (SR-OES) was used to investigate microwave activated H2/Ar/CH4 plasma under conditions of the electron cyclotron resonance (ECR). The chemistry and composition of the gas phase were studied using self-designed fibre-optic system with echelle type spectrometer during CVD deposition of polycrystalline diamond. One-dimensional intensity profiles of the main species were collected along...
-
Interactions of fish gelatin and chitosan in uncrosslinked and crosslinked with EDC films: FT-IR study
PublikacjaFilms based on fish gelatin, chitosan and blend of fish gelatin and chitosan before and after cross-linking with EDC have been characterized by FT-IR spectroscopy. The FT-IR spectrum of fish gelatin film showed the characteristic amide I, amide II and amide III bands, and the FT-IR spectrum of chitosan film confirmed that the polymer was only a partially deacetylated product, and included CH3-C=O and NH2 groups, the latter both...
-
Nowoczesne metody termochemicznej konwersji biomasy w paliwa gazowe, ciekłe i stałe = Modern methods of thermochemical biomass conversion into gas, liquid and solid fuels
PublikacjaBiomass utilization through direct- or co-combustion with coal, based on coal, hydrogen and oxygen compounds chemical energy conversion into heat in boilers, is simultaneously the cheapest and - according to experts - economically least effective solution. In case of heat and electricity production in cogeneration process in biomass fueled heat and power stations (wood, straw, energetic plants, RDF etc), investment costs are little...
-
Highly stable organic–inorganic junction composed of hydrogenated titania nanotubes infiltrated by a conducting polymer
PublikacjaA poly(3,4-ethylenedioxythiophene) conducting polymer doped with poly(2-styrene sulfonate) (pEDOT:PSS) was efficiently electrodeposited on a layer composed of ordered titania nanotubes. TiO2 nanotubes were formed during an anodization process and, after calcinations, a layer was subjected to hydrogen plasma. Hydrogenation leads to Ti(III) formation, a decrease in resistance, and a huge increase of donor density when compared with...
-
Risks related to car fire on innovative Poroelastic Road Surfaces-PERS
PublikacjaTo reduce tyre/road noise, the concept of poroelastic road surfaces (PERS) was invented. PERS is a road surface material that is porous, and at the same time, it is flexible because of the substantial amount of rubber granulate content (from 20% to 85%). The rubber and stone particles are bound by polyurethane resin instead of bitumen. It was feared that in case of fire, because of the high content of rubber and polyurethane, there...
-
Ultrafast Intramolecular Relaxation and Wave-Packet Motion in a Ruthenium-Based Supramolecular Photocatalyst
PublikacjaThe hydrogen-evolving photocatalyst [(tbbpy)2 Ru(tpphz)Pd(Cl)2 ](2+) (tbbpy=4,4'-di-tert-butyl-2,2'-bipyridine, tpphz=tetrapyrido[3,2-a:2',3'-c:3'',2''-h:2''',3'''-j]phenazine) shows excitation-wavelength-dependent catalytic activity, which has been correlated to the localization of the initial excitation within the coordination sphere. In this contribution the excitation-wavelength dependence of the early excited-state relaxation...
-
The influence of the welding environment on the properties of Tekken joints made from S355J2C+N steel
PublikacjaThere are three main methods of underwater welding: dry, wet and intermediate between them, by using the local dry chamber. Due to low costs, the most common method is the wet welding with the use of covered electrodes. Water as a welding environment carries out a lot of problems. The first is limited visibility and instability of the welding arc. The biggest problem during underwater welding is high susceptibility to cold cracking,...
-
Application of Spinel and Hexagonal Ferrites in Heterogeneous Photocatalysis
PublikacjaSemiconducting materials display unique features that enable their use in a variety of applications, including self-cleaning surfaces, water purification systems, hydrogen generation, solar energy conversion, etc. However, one of the major issues is separation of the used materials from the process suspension. Therefore, chemical compounds with magnetic properties have been proposed as crucial components of photocatalytic composites,...
-
Cold plasma treatment of tannic acid as a green technology for the fabrication of advanced cross-linkers for bioactive collagen/gelatin hydrogels
PublikacjaTannic acid (TA) is a natural compound studied as the cross-linker for biopolymers due to its ability to form hydrogen bonds. There are different methods to improve its reactivity and effectiveness to be used as a modifier for biopolymeric materials. This work employed plasma to modify tannic acid TA, which was then used as a cross-linker for fabricating collagen/gelatin scaffolds. Plasma treatment did not cause any significant...
-
Optimization of biocorrosion resistance and mechanical properties of PM Ti–XAl–2Fe–3Cu alloys by response surface methodology
PublikacjaIn the current study, the biocorrosion resistance and mechanical properties of the Ti–XAl–2Fe–3Cu (wt%) (X = 6, 4, 2 wt%) alloy produced by powder compact extrusion of blended elemental powders were optimized by using the response surface methodology in order to gain the best combination of processing parameters. To run the optimization process, central composite design with three equal levels of oxygen, hydrogen and aluminum was...
-
Influence of alkaline and oxidative pre-treatment of waste corn cobs on biohydrogen generation efficiency via dark fermentation
PublikacjaStages of waste corn cobs processing leading to the production of biohydrogen via dark fermentation are presented and discussed in this paper. Firstly, the effects of pretreatment conditions i.e. alkaline, alkaline-oxidizing and Fenton oxidizing pre-treatment of lignocellulosic biomass on the removal of lignin were examined. The solid residue obtained in the first stage was subjected to saccharification by means of enzymatic hydrolysis....
-
Investigation of praseodymium and samarium co-doped ceria as an anode catalyst for DIR-SOFC fueled by biogas
PublikacjaThe Pr and Sm co-doped ceria (with up to 20 mol.% of dopants) compounds were examined as catalytic layers on the surface of SOFC anode directly fed by biogas to increase a lifetime and the efficiency of commercially available DIR-SOFC without the usage of an external reformer. The XRD, SEM and EDX methods were used to investigate the structural properties and the composition of fabricated materials. Furthermore, the electrical...
-
Ultrafast degradation of brilliant cresyl blue under hydrodynamic cavitation based advanced oxidation processes (AOPs)
PublikacjaThe study highlights effectiveness of hydrodynamic cavitation (HC) in the degradation of effluents polluted by Brilliant Cresyl Blue (BCB) dye. Optimal process parameters were cavitation number 0.27, inlet pressure 1.70 bar, temperature 20 °C and pH 7. The efficiency of HC was investigated in combination with other advanced oxidation processes, including the addition of external oxidants (hydrogen peroxide, ozone, and sodium persulfate)...
-
Kinetic analysis of the reduction of a ternary system of Bi, Sb and Te oxides by hydrogen for BiSbTe3 synthesis
PublikacjaReduction in a hydrogen atmosphere of Bi2O3, Sb2O3 and TeO2 mixes oxides for the synthesis of BiSbTe3 was analysed. The reduction reactions of Sb2O3 and Sb2O4 oxides, as well as Bi2O3+Sb2O3 and Sb2O3+3TeO2 mix- tures, were also evaluated. The reduction of Sb2O4 is investigated for the first time. The reactions of the mixed oxides systems also were not the subject of research so far despite being used for synthesis of the (Bi,Sb)2Te3...