Filtry
wszystkich: 1458
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: FINITE ELEMENT METHODS, PIEZOELECTRIC DEVICES MODELS, FREEFEM
-
Machine Learning and Electronic Noses for Medical Diagnostics
PublikacjaThe need for noninvasive, easy-to-use, and inexpensive methods for point-of-care diagnostics of a variety of ailments motivates researchers to develop methods for analyzing complex biological samples, in particular human breath, that could aid in screening and early diagnosis. There are hopes that electronic noses, that is, devices based on arrays of semiselective or nonselective chemical sensors, can fill this niche. Electronic...
-
Calculation of self and mutual inductances of the switched reluctance machine mathematical model.
PublikacjaA mathematical model of the switched reluctance machine (SRM) in a drive system obtained using Lagrange's energy method and a method of calculation of self and mutual inductances of the SRM are presented in the paper. The self and mutual inductances are elements of Lagrange's function in generalised coordinates and have been calculated using the finite element method (FEM). Selected calculation results for the particular machine...
-
Failure Analysis of footbridge made of composite materials
PublikacjaFinite element method analysis of a pedestrian footbridge made of sandwich material is presented. The internal structure of the material is modelled as a structural shell assuming the Equivalent Single Layer approach (ESL). Two FEM commercial codes are employed. The response of the structure is studied in order to determine the load level that activates Hashin and Tsai-Wu failure criteria. Some practical aspects of designing footbridges...
-
Modal FEM Analysis of Ferrite Resonant Structures
PublikacjaThe finite-element method (FEM) is applied for modal analysis of ferrite-loaded spherical resonators. To improve the efficiency of the numerical calculations, the body-of-revolution (BOR) technique is utilized. Due to the frequency-dependent ferrite permeability, FEM leads to a nonlinear eigenvalue problem that is challenging to solve. To this end, Beyn’s method is proposed. The effectiveness of the proposed approach is confirmed...
-
Seismic Response of High-Rise Buildings Equipped with Base Isolation and Non-Traditional Tuned Mass Dampers
PublikacjaOne of the methods in structural control is the application of combinational control systems in order to reduce the response of structures during earthquakes. The aim of the present paper is to verify the effectiveness of a hybrid control strategy, combining base isolation and non-traditional tuned mass dampers (TMDs) (i.e., TMDs with dashpots directly connected to the ground) in suppressing structural vibrations of high-rise buildings....
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART IV) MODELLING THE HEATING PROCESS AND DETERMINING THE SERVICEABILITY OF HYDRAULIC COMPONENTS DURING THE STARTING-UP IN LOW AMBIENT TEMPERATURE
PublikacjaDesigners of hydraulically driven machines and devices are obliged to ensure during design process their high service life with taking into account their operational conditions. Some of the machines may be started in low ambient temperature and even in thermal shock conditions (due to delivering hot working medium to cold components). In order to put such devices into operation appropriate investigations, including experimental...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublikacjaThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Numerical Issues and Approximated Models for the Diagnosis of Transmission Pipelines
PublikacjaThe chapter concerns numerical issues encountered when the pipeline flow process is modeled as a discrete-time state-space model. In particular, issues related to computational complexity and computability are discussed, i.e., simulation feasibility which is connected to the notions of singularity and stability of the model. These properties are critical if a diagnostic system is based on a discrete mathematical model of the flow...
-
Buckling and initial post-local buckling behaviour of cold-formed channel member flange
PublikacjaThe initial post-buckling behaviour of a cold-formed channel member flange after its local buckling is investigated. An axially compressed column or beam subjected to pure bending is considered. The member material is assumed to follow a linear stress-strain relationship. The governing non-linear differential equation of the problem is derived using the minimum total potential energy principle. An approximate solution for the equation...
-
Discussion of Derivability of Local Residual Stress Level from Magnetic Stray Field Measurement
PublikacjaThe NDT procedure dubbed ‘metal magnetic memory’ method and the related ISO 24497 standard has found wide industrial acceptance in some countries, mainly in Russia and China. The method has been claimed by some researchers (Roskosz and Bieniek in NDT&E Int 45:55–62, 2012; Wilson et al. in Sens Actuators A 135:381–387, 2007) as having potential for quantitative determination of local residual stress state in engineering structures,...
-
Nonlinear material identification of heterogeneous isogeometric Kirchhoff–Love shells
PublikacjaThis work presents a Finite Element Model Updating inverse methodology for reconstructing heterogeneous materialdistributions based on an efficient isogeometric shell formulation. It uses nonlinear hyperelastic material models suitable fordescribing incompressible material behavior as well as initially curved shells. The material distribution is discretized by bilinearelements such that the nodal values...
-
SIMULATIONS OF FRACTURE IN CONCRETE BEAMS UNDER BENDING USING A CONTINUUM AND DISCRETE APPROACH
PublikacjaThe paper describes two-dimensional meso-scale results of fracture in notched concrete beams under bending. Concrete was modelled as a random heterogeneous 4-phase material composed of aggregate particles, cement matrix, interfacial transitional zones and air voids. Within continuum mechanics, the simulations were carried out with the finite element method based on a isotropic damage constitutive model enhanced by a characteristic...
-
Process engineering in circular economy
Kursy OnlineDefinition and principles of the circular economy (CE). The transition from a linear model to a circular model. Business models for the CE. Circular design and innovation. CE assessment carbon footprint, life cycle assessment. Case studies of the cities implementing the CE concept. CE policy and legislation (EU and Poland). Wastewater treatment plants as an element of the CE. Energy and nutrient recovery technologies in wastewater...
-
Analysis of human behavioral patterns
PublikacjaWidespread usage of Internet and mobile devices entailed growing requirements concerning security which in turn brought about development of biometric methods. However, a specially designed biometric system may infer more about users than just verifying their identity. Proper analysis of users’ characteristics may also tell much about their skills, preferences, feelings. This chapter presents biometric methods applied in several...
-
A study on transverse shear correction for laminated sandwich panels
PublikacjaThe paper presents a study on an application of the First Order Shear Deformation Theory in a linear static analysis of elastic sandwich panels. A special attention has been given to the issue of the transverse shear correction. Two benchmark examples of sandwich plate problems with known reference solutions have been selected for a comparative analysis performed with own Finite Element codes. Interesting results allowed for drawing...
-
Optimal configuration of an electrode array for measuring ventricles' contraction
PublikacjaAn influence of an electrode-array configuration on an impedance signal composition for a fixed spatial distribution of its sources is examined in the paper. The Finite Element Method and Geselowitz relationship were used for examining three different electrode-arrays. A sensitivity approach was used to evaluate each configuration assuming that localization of the signal source is known. A conductivity change, thus the source of...
-
Geometrically nonlinear analysis of shells - Benchmark problems for Autocad Robot Analysis Professional
PublikacjaThe aim of this work is to verify the suitability of commercial engineering software for geometrically nonlinear analysis of shells. This paper deals with the static, geometrically nonlinear analysis of shells made of an isotropic material. The Finite Element Method (FEM) is chosen to solve the problem. The results of the commercial software Autocad Robot Structural Analysis Professional (ARSAP) are compared with the litera-ture...
-
Smart Weighing Scale with Feet-Sampled ECG
PublikacjaIn a smart home, health and well-being monitoring systems could be embedded in everyday devices providing a pervasive care. A home bathroom scale is an example of such a device, typically used to measure body weight and very often its composition (e.g. body water/fat percentage). In this paper, we analyzed a potential use of the bathroom scale to measure electrocardiogram (ECG) from electrodes located on the scale's tile. In particular...
-
THE PHASE SHIFTERS INFLUENCE ON THE POWER SYSTEM STABILITY
PublikacjaThe paper presents the effect of phase shifters as FACTS devices on the possibility of improving the angle stability. Presented results obtained by the dynamic simulation performed on the mathematical model of the three machine system cooperating with the 400 kV network. The generative blocks models include turbine models with their controllers and models of synchronous generators with their excitation systems and voltage regulation....
-
Low-Cost Design Optimization of Microwave Passives Using Multi-Fidelity EM Simulations and Selective Broyden Updates
PublikacjaGeometry parameters of contemporary microwave passives have to be carefully tuned in the final stages of their design process to ensure the best possible performance. For reliability reasons, the tuning has to be to be carried out at the level of full-wave electromagnetic (EM) simulations. This is because traditional modeling methods are incapable of quantifying certain phenomena that may affect operation and performance of these...
-
Dynamic analysis of the railway bridge span under moving loads
PublikacjaThe first part of this paper provides a review of the state of knowledge of the dynamic behaviour of railway bridges under moving loads. Particular attention is paid to developments in modelling railway bridge loading and dynamic vehicle-span (structure) interaction. The most important aspects determining the advancements in this area of knowledge are identified. The contemporary techniques for defining bridge span finite element...
-
Rozkład naprężeń mechanicznych w łyżce o szerokości 500 mm, przeznaczonej do koparki podsiębiernej
PublikacjaW artykule zaprezentowano optymalizację kształtu łyżki koparki przedsiębiernej z wykorzystaniem analizy wytrzymałościowej. Analizę oparto na trójwymiarowym modelu konstrukcji łyżki z zastosowaniem metody elementów skończonych (MES). Opracowanie wspomnianej metody pozwoliło na modyfikację konstrukcji łyżki, która dała w efekcie obniżenie naprężeń złożonych w newralgicznych obszarach konstrukcji łyżki. Przedstawiona analiza okazała...
-
Introduction of SAF-T in selected European countries together with applicable national names
Dane BadawczeAmong the methods used by individual countries in norder to seal the tax collection the introduction of the Standard Audit File for Tax is one of the most important ones.
-
An analytical four-layer horizontal electric current dipole model for analysing underwater electric potential in shallow seawater
PublikacjaThe paper presents a new analytical four‑layer (air–water–bottom–non‑conductive layer) horizontal electric dipole model which allows an accurate approximation of ship’s Underwater Electric Potential (UEP) from a sufficient depth in shallow coastal marine waters. The numerical methods, usually Finite Element Method (FEM) or Boundary Elements Method (BEM), are typically used to estimate the electric field and the distribution of...
-
Macromodels for efficient FEM simulations of waveguides and resonators
PublikacjaThis paper introduces a novel technique for enhancing the efficiency of the finite element method (FEM) by incorporating special modules, called macromodels, into the standard eigenvalue formulation. The number of unknowns in the separated macromodel subdomain can be significantly reduced by orthogonal projection, using the efficient nodal order reduction algorithm. The idea of macromodels implementation is demonstrated on a simple...
-
Diagnostics of bolted lap joint using guided wave propagation
PublikacjaThe paper presents numerical and experimental analyses of elastic waves propagation in a bolted lap joint. In experimental investigations condition assessment of the joint was performed with the use of symmetric waves excited by a piezoactuator. Numerical calculations were conducted in commercial finite element method software Abaqus. The influence of number of bolts and the value of the initial stress on recorded signals was examined....
-
Nondestructive Testing of the Miter Gates Using Various Measurement Methods
PublikacjaWhen any problems related to civil engineering structures appear, identifying the issue through the usage of only one measuring method is difficult. Therefore, comprehensive tests are required to identify the main source. The strains and displacement measurements, as well as modal identification, are widely used in the nondestructive testing of structures. However, measurements are usually carried out at several points and confirm...
-
A material model of asphalt mixtures based on Monte Carlo simulations
PublikacjaThe paper aims to numerically reflect mineral-asphalt mixture structure by a standard FEM software. Laboratory test results are presented due to bending tests of circular notched elements. The result scatter is relatively high. An attempt was made to form a random aggregate distribution in order to obtain various results corresponding to laboratory tests. The material structure calibration, its homogenization and finite element...
-
Residual Current Devices: Selection, Operation, and Testing
PublikacjaIn this book, the idea for residual current protection has been presented. The evolution in construction types of residual current devices, which has taken place over decades, is discussed. Types and functional properties of the contemporary residual current devices are described. The main parameters of these devices, from the point of view of their selection and application, are indicated. Special constructions of the protective...
-
Experimental and computational study on mechanical behaviour of carpentry corner log joints
PublikacjaThis work concerns experimental and numerical research on carpentry joints used in historic wooden buildings in southeastern Poland and western Ukraine. These structures are mainly sacred buildings, and the types of corner log joints characteristic of this region are primarily saddle-notch and dovetail joints; thus, these two types of joints were analysed in this study. The modelling of historic timber structures is a complex...
-
ESTYMACJA WSPÓŁCZYNNIKÓW SZTYWNOŚCI ZAMOCOWANIA PODATNEGO PRZEDMIOTU OBRABIANEGO NA STOLE FREZARKI
PublikacjaW pracy przedstawiono metodę estymacji współczynników sztywności Elementów Sprężystych (ES) modelujących zamocowanie podatnego wielkogabarytowego przedmiotu obrabianego na stole frezarki. Proponowana metoda bazuje na algorytmie optymizacji za pomocą roju cząstek (ang. Particle Swarm Optimization), który pozwala na uzyskanie dobrej zgodności (aktualizacji) modelu Metody Elementów Skończonych (MES) z modelem pochodzącym z identyfikacji...
-
Justyna Signerska-Rynkowska dr inż.
OsobySince 2021 visiting assistant professor in Dioscuri Centre in Topological Data Analysis (Institute of Mathematics of the Polish Academy of Sciences, IMPAN) Since 2016 assistant professor at Gdańsk University of Technology, Faculty of Applied Physics and Mathematics, Department of Differential Equations and Mathematics Applications 2020 - 2023 Principal Investigator in "SONATA" grant “Challenges of low-dimensional...
-
Expedited EM-Driven Design of Miniaturized Microwave Hybrid Couplers Using Surrogate-Based Optimization
PublikacjaMiniaturization of microwave hybrid couplers is important for contemporary wireless communication engineering. Using standard computer-aided design methods for development of compact structures is extremely challenging due to a general lack of computationally efficient and accurate simulation models. Poor accuracy of available equivalent circuits results from neglecting parasitic cross-couplings that greatly affect the performance...
-
Composite sandwich footbridge - measured dynamic response vs. FEA
PublikacjaThe paper describes a process of in situ dynamic tests of a composite sandwich footbridge before its accepta-tion for exploitation in real traffic conditions. It is only a part of a big research task that includes design, manufacture and introduce practical application of the bridge. The in situ measured natural modes and fre-quencies are compared with numerically determined ones. Finite element analysis is established to estimate...
-
Domain Reduction in Hybrid Technique for Electromagnetic Wave Scattering Problems
PublikacjaThis paper proposes a combination of the field matching technique, finite element method and generalized impedance matrix, the main idea of which is to reduce the computational domain by surrounding a scatterer with the smallest convex shape and applying the field matching technique. This approach can be applied for arbitrary shaped scatterers and types of materials and allows for the reduction of the computational domain. In order...
-
Fault diagnosing system of wheeled tractors
PublikacjaA defect of complex wheeled tractor assembles most frequently negative influence on exploitation efficiency, safety and exhaust gases emission. Structure complexity of wheeled tractors requires more and more advanced diagnostic methods for identification of their serviceable possibilities as well in manufacturing step as in exploitation. In classical diagnosing methods of wheeled tractor defects states mapping by measured diagnostic...
-
Influence of the femoral offset on the muscles passive resistance in total hip arthroplasty
PublikacjaBackground Soft tissue tension is treated as a crucial factor influencing the post-THA dislocation. The femoral offset is regarded as one of the major parameters responsible for the stabilization of the prosthesis. It is unclear which soft tissue is mostly affected by the offset changes. Methods A finite element model of the hip was created. The model comprised muscles, bones, a stem, the acetabular component and a liner. The muscles...
-
Fluid–solid interaction on a thin platelet with high-velocity flow: vibration modelling and experiment
PublikacjaThe paper concerns the nonlinear behaviour of a thin platelet that is streamlined in an aerodynamic tunnel. The air velocity in the aerodynamic tunnel was at 858.9 km/h or 0.7 Ma (Ma—Mach number is a dimensionless quantity in fluid dynamics representing the ratio of flow velocity past a boundary to the local speed of sound). This experiment was numerically simulated using FSI (fluid–solid interaction) tools, namely the coupling...
-
A device for measuring heat flux on a rocket skin surface
PublikacjaA novel method for measuring heat flux on a surface is presented. It is an extensive upgrade of currently known heat flux sensors used mostly in civil engineering. As the thermal environment of launchers, especially sounding rocket can have an enormous negative effect on payload, careful considerations have to be taken in the process of preparing insulation. Usually, thermal data provided by the launch vehicle manufacturer is limited...
-
Optimization of the Hardware Layer for IoT Systems using a Trust Region Method with Adaptive Forward Finite Differences
PublikacjaTrust-region (TR) algorithms represent a popular class of local optimization methods. Owing to straightforward setup and low computational cost, TR routines based on linear models determined using forward finite differences (FD) are often utilized for performance tuning of microwave and antenna components incorporated within the Internet of Things systems. Despite usefulness for design of complex structures, performance of TR methods...
-
Topological-numerical analysis of a two-dimensional discrete neuron model
PublikacjaWe conduct computer-assisted analysis of a two-dimensional model of a neuron introduced by Chialvo in 1995 [Chaos, Solitons Fractals 5, 461–479]. We apply the method of rigorous analysis of global dynamics based on a set-oriented topological approach, introduced by Arai et al. in 2009 [SIAM J. Appl. Dyn. Syst. 8, 757–789] and improved and expanded afterward. Additionally, we introduce a new algorithm to analyze the return times...
-
Experimental comparison of the transition speed of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaA journal bearing test bench is used to find the transition speed between the hydrodynamic and mixed lubrication regimes for a modified magnetorheological (MR) fluid. It is shown that the transition speed of the bearing can be reduced by applying a local magnetic field near minimum film when it is lubricated with the MR fluid, and that this will only marginally increase friction. The lubricating performance of the MR fluid is compared...
-
Simulation of the switched reluctance drive system
PublikacjaSwitched reluctance motors (SRM), unlike other types of motors, for their application require a control system and the supply from a power electronic converter. A method of modelling and mathematical model of an SRM in a switched reluctance drive (SRD) system is presented in the paper. Modelling is based on Lagrange's energy method. Coefficients of the Lagrange's equation have been calculated using the finite element method (FEM)....
-
Fluid Mechanics, L/L/E, DaPE, sem. 04, summer 21/22 (PG_00050282)
Kursy OnlineLECTURES Introduction and basic definitions. Properties of fluids. Models of fluids. Fluids in equilibrium. Determination of hydrostatic forces. Archimedes" law. Methods of fluid flow description. General motion of fluid. Deformation of fluid element. Vortex motion of fluid. Principles of conservation of mass, momentum and energy. Balance of entropy. Navier-Stokes equation. Bernoulli equation. Similarity of flow phenomena. Potential...
-
Microfluidic devices for photo-and spectroelectrochemical applications
PublikacjaThe review presents recent developments in electrochemical devices for photo- and spectroelectrochemical investigations, with the emphasis on miniaturization (i.e., nanointerdigitated complementary metal-oxide-semiconductor devices, micro- and nano-porous silicon membranes or microoptoelectromechanical systems), silica glass/microreactors (i.e., plasmonic, Raman spectroscopy or optical microcavities) or polymer-based devices (i.e.,...
-
Robustness in Compressed Neural Networks for Object Detection
PublikacjaModel compression techniques allow to significantly reduce the computational cost associated with data processing by deep neural networks with only a minor decrease in average accuracy. Simultaneously, reducing the model size may have a large effect on noisy cases or objects belonging to less frequent classes. It is a crucial problem from the perspective of the models' safety, especially for object detection in the autonomous driving...
-
Sano-Tachiya-Noolandi-Hong, Onsager and Braun models vs Monte Carlo simulation of charge photogeneration in organic solids
PublikacjaThe Sano-Tachiya-Noolandi-Hong (STNH), Onsager, and Braun models as well as Monte Carlo (MC) simulations of charge recombination/separation have been applied for the first time to reproduce the results of the electromodulated photoluminescence measurements in vacuum-evaporated films of fluorescent materials commonly used in optoelectronic devices. The values of the electron-hole pair final recombination speed in the monomer emitters:...
-
Response of high voltage disconnector under seismic excitation - experimental and numerical study
PublikacjaThe efficiency of the energetic infrastructure system is a very import safety issue in the region experienced by the ground motion. The aim of the present paper is to show the results of the experimental and numerical study focused on the earthquake-induced response of the high voltage disconnector, which is an important element of energetic network. First, the impact tests as well as the sweep-sine shaking table tests were conducted....
-
Use of Neural Networks in Diagnostics of Rolling-Element Bearing of the Induction Motor
PublikacjaBearing defect is statistically the most frequent cause of an induction motor fault. The research described in the paper utilized the phenomenon of the current change in the induction motor with bearing defect. Methods based on the analysis of the supplying current are particularly useful when it is impossible to install diagnostic devices directly on the motor. The presented method of rolling-element bearing diagnostics used indirect...
-
Evaluation of Three Peptide Immobilization Techniques on a QCM Surface Related to Acetaldehyde Responses in the Gas Phase
PublikacjaThe quartz-crystal microbalance is a sensitive and universal tool for measuring concentrations of various gases in the air. Biochemical functionalization of the QCM electrode allows a label-free detection of specific molecular interactions with high sensitivity and specificity. In addition, it enables a real-time determination of its kinetic rates and affinity constants. This makes QCM a versatile bioanalytical screening tool for...