Filtry
wszystkich: 1732
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: FINTE ELEMENT METHOD MECHATRONIC SYSTEMS
-
Framework for RIDM within functional safety management process
PublikacjaThe functional safety management in life cycle is a complex process starting with identifying hazards and defining safety-related functions (SRFs) with risk assessment oriented at determining the safety integrity level. Another element of such life cycle is a verification of required SIL for designed safety-related system which implements safety function. Due to complexity of the problem, to overcome difficulties in safety-related...
-
Modal analysis of temporary steel grandstand equipped with different bracing systems
PublikacjaThe aim of this paper is to present the results of numerical analysis focused on temporary steel scaffolding grandstand. The investigation has been devoted to modal analysis where modes of free vibrations and corresponding natural frequencies have been estimated and compared. The structure was equipped with different types of stiffener members. One on them is a typical tubular stiffener, while the second one is spe-cially designed...
-
Buckling of thin-walled columns accounting for initial geometrical imperfections
PublikacjaThe paper is devoted to the effect of some geometrical imperfections on the critical buckling load of axially compressed thin-walled I-columns. The analytical formulas for the critical torsional and flexural buckling loads accounting for the initial curvature of the column axis or the twist angle respectively are derived. The classical assumptions of theory of thin-walled beams with non-deformable cross-sections are adopted. The...
-
Large deformation finite element analysis of undrained pile installation
PublikacjaIn this paper, a numerical undrained analysis of pile jacking into the subsoil using Abaqus software suit has been presented. Two different approaches, including traditional Finite Element Method (FEM) and Arbitrary Lagrangian–Eulerian (ALE) formulation, were tested. In the first method, the soil was modelled as a two-phase medium and effective stress analysis was performed. In the second one (ALE), a single-phase medium was assumed...
-
Impulse Impedance Measurements of Lightning Protection Earthings
PublikacjaLightning protection earthing systems should be tested at currents with time parameters similar to those of lightnings. A method and definition of a measured value of impulse impedance are introduced. The impulse impedance was determined by a quotient of voltage drop on the tested earthing to a value of current in measure circuit. The usefulness of the impulse method for lightning protection evaluation is tested on radio base stations...
-
Corrosion monitoring by harmonic analysis in aqueous environments
PublikacjaThis paper presents tests concerning the rate of corrosion in non-alloy steel (type S235JR) in an aqueous environment, with an additive of sodium chloride by means of polarization resistance measurements and harmonic analysis. The tests have been carried out for steel samples exposed to the testing environment for six weeks, in order to obtain a constant rate of corrosion in the function of time. The measurements have aimed at...
-
The concept of knowledge bases supporting the it systems integration model
PublikacjaThis paper presents main concepts regarding the design of a knowledge base in order to support IT systems integration. The main goal of the research is to develop a universal method of integration of various systems concerning any possible area of interest. The concept is based on creating a generic mechanism which would support the decision regarding the choice of the integration model. The most important tasks include: key factors...
-
Stakeholders Satisfaction Index as an Important Factor of Improving Quality Management Systems of Universities in Poland
PublikacjaThe following article analyses the role of stakeholders in selected methods of assessing the quality of educational services of universities and discusses quality management systems according to Common Assessment Framework for education. Furthermore, it presents the example of method of stakeholder satisfaction measurement called Stakeholders Satisfaction Index (SSI) which is an original proposal of an aggregate measure of satisfaction...
-
Projektowanie układów ramowych z zastosowaniem analizy wrażliwości
PublikacjaW pracy przedstawiono przykład projektowania układów ramowych z zastosowaniem analizy wrażliwości. Rozważane układy ramowe rozwiązano autorskim programem napisanym w środowisku MATLAB, metodą elementów skończonych. Badano wpływ zmiany modułu Younga oraz wpływ zmiany wielkości przekroju poprzecznego na wybrane przemieszczenia ramy. Przedstawiono wyniki dla analizy wrażliwości jedno i wieloparametrycznej.
-
A Mesh Deformation Technique Based on Solid Mechanics for Parametric Analysis of High-Frequency Devices With 3-D FEM
PublikacjaIn this paper, a versatile technique for mesh defor- mation is discussed, targeted at the electromagnetic (EM) field simulation of high-frequency devices using the 3-D finite element method (FEM). The approach proposed applies a linear elasticity model to compute the displacements of the internal mesh nodes in 3-D when the structure geometry is changed. The technique is compared with an alternative approach...
-
Dynamic Tests and Technical Monitoring of a Novel Sandwich Footbridge
PublikacjaA novel sandwich composite footbridge is described in this paper, for the first time after it has been put into operation over the Radunia River in the Pruszcz Gdański municipality. This paper presents results of dynamic tests and describes technical monitoring of the footbridge. The dynamic tests were conducted to estimate pedestrian comfort and were compared with the ones from numerical simulations made in the environment of...
-
Inverse Analysis as a Key Element of Safety Assessment under the Snow Load For The Large Suspension Roofs Structure
PublikacjaThe paper presents a concept and realization of monitoring system for the Silesian Stadium in Chorzow. The idea of the system lies in fusion of structure monitoring with a calibrated numerical FEM model [1]. The inverse problem is solved. On the base of measured selected displacements, the numerical FEM model of the structure combined with iterative method, develops the current snow load distribution. Knowing the load, we can calculate...
-
Reliable Greedy Multipoint Model-Order Reduction Techniques for Finite-Element Analysis
PublikacjaA new greedy multipoint model-order reduction algorithm for fast frequency-domain finite-element method simulations of electromagnetic problems is proposed. The location of the expansion points and the size of the projection basis are determined based on a rigorous error estimator. Compared to previous multipoint methods, the quality of the error estimator is significantly improved by ensuring the orthogonality of the projection...
-
Vibrational Properties of LaNb0.8M0.2O4-δ (M=As, Sb, V, and Ta)
PublikacjaLaNb0.8M0.2O4-δ (where M=As, Sb, V, and Ta) oxides with pentavalent elements of different ionic sizes were synthesized by a solid-state reaction method. The vibrational properties of these oxides have been investigated. These studies revealed that the substituent element influences both Debye temperature value as well as the Raman active vibrational modes. Additionally, the low-temperature vibrational properties of LaNb0.8Sb0.2O4-δ...
-
Numerical and experimental investigation of rotational stiffness of zed-purlins connection with sandwich panels
PublikacjaA rotational resistant stiffness of the zed-purlins connection with sandwich panels is investigated. A simple finite element method model of the connection is proposed. The numerical analysis of the model performed by ABAQUS software, in physically linear and geometrically nonlinear ranges, leads to the rotational resistant stiffness sought. The numerical solution obtained is verified experimentally. Two variants of distribution...
-
Badania deformacji w materiałach sypkich podczas dynamicznego przepływu w silosach
PublikacjaMonografia stanowi próbę połączenia analizy zagadnień powstawania zmian objętościowych oraz pomiaru zmian koncentracji materialu sypkiego podczas opróżniania silosu. W pracy przedstwiono wyniki pomiarów wykonanych z zastooswaneim metody Particle Image Velocimetry, Electrical Capacitance Toomography oraz promieniowania rentgenowskiego. Zamieszczono równeiz wyniki obliczeń wykoanaych z zastooswaniem metody DEM (Discrete Element...
-
ECHOES REDUCTION DURING DIGITAL DATA TRANSMISSION IN HYDROACOUSTIC CHANNEL – LABORATORY EXPERIMENT
PublikacjaThe possibility of using a hydroacoustic channel for digital data transmission is very limited. This is due to the effect of multipath propagation of the emitted acoustic wave and the damping of the mechanical wave in this medium, which increase with frequency. The first of these phenomena results in inter-symbol interference disturbances in data transmission systems, including even hundreds of symbols. Due to the number of reflections...
-
Awareness evaluation of patients in vegetative state employing eye-gaze tracking system
PublikacjaApplication of eye-gaze tracking system to awareness evaluation is demonstrated. Hitherto awareness evaluation methods are presented. The assumptions of proposed method based on analysis of visual activity of patients in vegetative state are demonstrated. The eye-gaze tracking system ''Cyber-Eye'' developed at the Multimedia Systems Department employed to conducted experiments is presented. Research described in the paper indicates...
-
Novel approach to modeling spectral-domain optical coherence tomography with Monte Carlo method
PublikacjaNumerical modeling Optical Coherence Tomography (OCT) systems is needed for optical setup optimization, development of new signal processing methods and assessment of impact of different physical phenomena inside the sample on OCT signal. The Monte Carlo method has been often used for modeling Optical Coherence Tomography, as it is a well established tool for simulating light propagation in scattering media. However, in this method...
-
3D intact knee model used in analysis of the medial meniscus biomechanics in the osteoarthritic knee joint - input text file for computation
Dane BadawczeThe finite element method was used to simulate the stance phase of the gait cycle. An intact knee model with original geometry and material parametetrs was prepared based on magnetic resonance scans of the left knee joint of a healthy volunteer. The file was created in Abaqus 6.14-2, but can be read in a text editor.
-
A complete impedance analysis of electrochemical cells used as energy sources
PublikacjaA comprehensive description of impedance ofelectrochemical systems has been presented, along withthe assumptions of the method used. In this method, amultisinusoidal current excitation signal is used. Thechanges of potential of both the electrodes and thepotential difference between these electrodes are allregistered simultaneously as a function of time. Theproposed method offers the possibility of separatelydetermining the instantaneous...
-
Fluid–solid interaction on a thin platelet with high-velocity flow: vibration modelling and experiment
PublikacjaThe paper concerns the nonlinear behaviour of a thin platelet that is streamlined in an aerodynamic tunnel. The air velocity in the aerodynamic tunnel was at 858.9 km/h or 0.7 Ma (Ma—Mach number is a dimensionless quantity in fluid dynamics representing the ratio of flow velocity past a boundary to the local speed of sound). This experiment was numerically simulated using FSI (fluid–solid interaction) tools, namely the coupling...
-
Numerical simulations of novel GFRP sandwich footbridge
PublikacjaIn the following paper some aspects of numerical analysis and designing stages of a footbridge made of composite materials are elucidated. Because of the used materials the design process in this case is not ordinary and requires the development of concepts, material selections, identification of material properties, numerical simulations, strength calculations, serviceability and durability analyses. This contribution presents...
-
Selection of excitation signals for high-impedance spectroscopy
PublikacjaA method of fast impedance spectroscopy of technical objects with high impedance (|Zx| > 1 GOhm) is evaluated in this paper. An object is excited with a signal generated by a digital-to-analog converter (DAC) located on the U2531A DAQ module. Response signals proportional to current flowing through and voltage across the measured object are sampled by analog-to-digital converters (ADC) in the DAQ module. The object impedance spectrum...
-
A three-dimensional periodic beam for vibroacoustic isolation purposes
PublikacjaThis paper presents results of investigations on a three-dimensional (3-D) isotropic periodic beam. The beam can represent a vibroacoustic isolator of optimised dynamic characteristics in the case of its longitudinal, flexural and torsional behaviour. The optimisation process concerned both the widths as well as the positions of particular frequency band gaps that are present in the frequency spectrum of the beam. Since the dynamic...
-
Two‐functional μBIST for Testing and Self‐Diagnosis of Analog Circuits in Electronic Embedded Systems
PublikacjaThe paper concerns the testing of analog circuits and blocks in mixed‐signal Electronic Embedded Systems (EESs), using the Built‐in Self‐Test (BIST) technique. An integrated, two‐functional, embedded microtester (μBIST) based on reuse of signal blocks already present in an EES, such as microprocessors, memories, ADCs, DACs, is presented. The novelty of the μBIST solution is its extended functionality. It can perform 2 testing functions:...
-
Evaluation of electrical parameters of traction supply system for complex railway traffic conditions, using simulation methods
PublikacjaDevelopment of electrified transport systems, railways modernization, expansion of urban transport networks, purchases of modern rolling stock causes that updating of electric traction supply system is necessary. This chapter presents an effective method for electrical parameters of traction supply system evaluation, using simulation methods.
-
Estimation of electrode contact in capacitive ECG measurement
PublikacjaIn the paper a method of electrode’s contact estimation in capacitive electrocardiogram (CECG) is presented. Proposed solution allows estimation of contact quality for each individual electrode. This enables construction of multi-electrode CECG systems, where electrode pairs can be selected on the basis of the individual electrode contact quality.
-
Distributed Detection of Selected Features in Data Streams Using Grid-class Systems
PublikacjaThis chapter describes basic methodology of distributed digital signal processing. A choice of distributed methods of detection of selected features in data streams using grid-class systems is discussed. Problems related to distribution of data for processing are addressed. A mitigating method for data distribution and result merging is described.
-
Probabilistic Analysis of Structure Models using Target Random Sampling (TRS)
PublikacjaThe work presents testing methods of sensitivity and reliability of mechanical or structural systems. All computations concerned the case of Zigler column, a simple model of a compressed column involving two random variables only. A conclusion was drawn that the standard Monte Carlo method, its reduction variants and the response surface method allow to assess the sensitivity of structural response to the variation of random structural...
-
Path Loss Modelling for Location Service Applications
PublikacjaThe aim of this paper is the path loss modeling for the radiolocation services in radiocommunication networks, particularly in cellular networks. The main results of the measurements obtained in the physical layer of the UMTS are introduced. A new method for the utilization of the multipath propagation phenomenon to improve the estimation of the distance between the mobile station (MS) and the base station (BS) is outlined. This...
-
Yade-open DEM: an open-source software using a discrete element methodto simulate granular material
PublikacjaPurpose - YADE-OPEN DEM is an open source software based on the Discrete Element Method which uses object oriented programming techniques. The paper describes the softwarearchitecture.Design/methodology/approach - The DEM chosen uses position, orientation, velocity and angular velocity as independent variables of simulated particles which are subject to explicit leapfrog time-integration scheme (Lagrangian method). The three-dimensional...
-
Numerical analysis of mechanical properties of an infill structure used in 3D printings
PublikacjaThe paper presents results of a numerical analysis focused on an identification of mechanical properties of an element created by using Fused Deposition Modelling additive manufacturing technique (FDM). There is presented a description of technology of the 3D printing, numerical model created by using the finite element method (FEM), as well as some problems referred to estimation of the mechanical properties of the printout. The...
-
Numerical modelling and analysis of steel specimens subjected to marine immersed corrosion and tensile load
PublikacjaThe present study develops numerical models to analyse the behaviour of steel specimens subjected to marine immersed corrosion degradation and tensile load. The finite element method with the use of the explicit dynamic solver LS-DYNA, satisfying the quasi-static conditions, is employed. Two numerical models are developed, where in the first one, the scans of surfaces gathered from corroded plate specimens are implemented directly...
-
Modal analysis of a steel grandstand
PublikacjaAmong the issues related to the idea of sustainable society is the safety of civil engineering structures devoted to satisfy different needs of people. One of the types of structures devoted to satisfy recreational needs are grandstands, which are used during sport events or music concerts. It is obligatory to consider interaction between structure and crowd load especially when the crowd movement involves rhythmic jumping, dancing,...
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublikacjaIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublikacjaIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
-
Bioelectronic nose: Current status and perspectives
PublikacjaA characteristic feature of human and animal organs of smell is the ability to identify hundreds of thousands of odours. It is accompanied by particular smell sensations, which are a basic source of information about odour mixture. The main structural elements of biological smell systems are the olfactory receptors. Small differences in a structure of odorous molecules (odorants) can lead to significant change of odour, which is...
-
Koncepcja i analiza sensora/aktuatora piezoelektrycznego do pomiaru procesu starzenia się ludzkiej skóry
PublikacjaNiniejszy artykuł przedstawia nową koncepcję piezoelektrycznego sensora/aktuatora przeznaczonego do pomiaru właściwości mechanicznych tkanek miękkich a w szczególności skóry ludzkiej. Wyjaśnione jest analityczne podejście z wykorzystaniem schematu zastępczego Mason’a określającego aktuator w stanie rezonansu oraz opis metody impedancji elektromechanicznej wykorzystanej w systemie pomiarowym. Analiza z użyciem metody elementów...
-
Approaching Secure Industrial Control Systems
PublikacjaThis study presents a systematic approach to secure industrial control systems based on establishing a business case followed by the development of a security programme. To support these two fundamental activities the authors propose a new method for security cost estimation and a security assessment scheme. In this study they explain the cost evaluation technique and illustrate with a case study concerning the assessment of the...
-
Progressive failure analysis of laminates in the framework of 6-field nonlinear shell theory
PublikacjaThe paper presents the model of progressive failure analysis of laminates incorporated into the 6-field non-linear shell theory with non-symmetrical strain measures of Cosserat type. Such a theory is specially recommended in the analysis of shells with intersections due to its specific kinematics including the so-called drilling rotation. As a consequence of asymmetry of strain measures, modified laminates failure criteria must...
-
Search for the most useful geometry of an acoustic journal bearing
PublikacjaComputer simulations of a number of journal bearing’s geometries utilising acoustic levitation were carried out. The choice of the best geometry depended on the ability of a deformed shape, created by piezo-electric elements, to facilitate squeeze film ultrasonic levitation, and also to create three evenly distributed diverging aerodynamic gaps. Deformations of analysed variants of the bearing’s shape were generated by numerical...
-
A role of an Enterprise Identification Card in a building process of water tourist investments
PublikacjaAn essential element of a building process for water tourist investments in Poland is a document called the Enterprise Identification Card. It is required for the investments, which are classified according to the Regulation [1] as the ones that could potentially impact the environment. It is assumed that KIP is there to protect the environment against the excessive human interference and it just provides the guidelines regarding...
-
Numerical estimation of the pile toe and shaft unit resistances during the installation process in sands
PublikacjaNumerical simulations of a pile jacking were carried out. A Coupled Eulerian–Lagrangian (CEL) formulation was used to treat with large deformation problems. An Abaqus, a commercial Finite Element Method software suit, was used as a computing environment. The Mohr–Coulomb constitutive model was applied and the Coulomb model of friction was used to describe pile-soil interaction. Calculations were made for three different pile diameters....
-
Hydrodynamic Pressure Field of a Ship on Shallow Water
PublikacjaResults of calculations of the hydrodynamic pressure field around the ship were obtained by application of the boundary element method. Hydrodynamic field was calculated for a Polish Navy’s tugboat and transport ship using a program called SHiPP and compared with measurements of the field taken on river near Swinoujscie for two identical tugs H-4 and H-10. Next, a series of HPF calculations was carried out on planes situated at...
-
Numerical investigations on early indicators of fracture in concrete at meso-scale.
PublikacjaFracture is a major reason of the global failure of concretes. The understanding of fracture is important to ensure the safety of structures and to optimize the material behaviour. In particular an early prediction possibility of fracture in concretes is of major importance. In this paper, concrete fracture under bending was numerically analysed using the Discrete Element Method (DEM). The real mesoscopic structure of a concrete...
-
Simplified method of water cooled exhaust system design.
PublikacjaThe water cooled exhaust systems are not often used onboard ships. Prime goal is to lower temperature of exhaust gas from main propulsion and auxiliary engines to the defined limit. The design of such systems require detailed analysis of propulsion system operational parameters to meet designer expectations. The paper outlines the cooled exhaust system design problems in specific application. The simplified method of evaluation...
-
Smart Innovation Engineering: Toward Intelligent Industries of the Future
PublikacjaKnowledge-based Engineering Systems are founded upon integration of knowledge into computer systems and are one of the core requirements for the future Industry 4.0. This paper presents a system called Smart Innovation Engineering (SIE) capable of facilitating product innovation process semi-automatically. It enhances decision-making processes by using the explicit knowledge of formal decision events. The SIE system carries the...
-
An algorithm to generate high dense packing of particles with various shapes
PublikacjaDiscrete Element Method (DEM) is one of available numerical methods to compute movement of particles in large scale simulations. The method has been frequently applied to simulate the cases of grain or bulk material as the major research issue. The paper describes a new method of generating high dense packing with mixed material of two different shape used in DEM simulation. The initial packing is an important parameter to control,...
-
Detection of Water on Road Surface with Acoustic Vector Sensor
PublikacjaThis paper presents a new approach to detecting the presence of water on a road surface, employing an acoustic vector sensor. The proposed method is based on sound intensity analysis in the frequency domain. Acoustic events, representing road vehicles, are detected in the sound intensity signals. The direction of the incoming sound is calculated for the individual spectral components of the intensity signal, and the components...