wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: LINEAR ALKYLBENZENE SULPHONATES
-
Measurements of drive system properties of the "Magnetic SpeedLine" ultra-fast robot prototype for IML labeling
Dane BadawczeTests of the drive system of the ultra-fast robot "SpeedLine magnetic" for labeling with the IML method were carried out in order to analyze the influence of the operating parameters of the drive system on the correctness and quality of the drive system.
-
Dilatometry results of SrTi0.50Fe0.50O3-d powder
Dane BadawczeThis dataset contains results of dilatometry measurements of SrTi0.50Fe0.50O3-d powder. The investigation of the linear thermal expansion was carried out using a Netzsch DIL402 dilatometer. The SrTi0.50Fe0.50O3-d powder was formed into cylinders and heat up to 1100 °C with a heating rate of 5 °C min−1, dwelled for 15 min, and then cooled at a rate of...
-
Dilatometry results of SrTi0.65Fe0.35O3-d powder
Dane BadawczeThis dataset contains results of dilatometry measurements of SrTi0.65Fe0.35O3-d powder. The investigation of the linear thermal expansion was carried out using a Netzsch DIL402 dilatometer. The SrTi0.65Fe0.35O3-d powder was formed into cylinders and heat up to 1100 °C with a heating rate of 5 °C min−1, dwelled for 15 min, and then cooled at a rate of...
-
Dilatometry results of SrTi0.30Fe0.70O3-d powder
Dane BadawczeThis dataset contains results of dilatometry measurements of SrTi0.30Fe0.70O3-d powder. The investigation of the linear thermal expansion was carried out using a Netzsch DIL402 dilatometer. The SrTi0.30Fe0.70O3-d powder was formed into cylinders and heat up to 1100 °C with a heating rate of 5 °C min−1, dwelled for 15 min, and then cooled at a rate of...
-
Direct shear stress vs strain relation for fiber reinforced composites
PublikacjaThe majority of fiber reinforced composites exhibit strong non-linear behavior in in-plane shear state. The effect is attributed to the micro-cracks appearing in the matrix and can be modeled on the micro and macro level. In this work the author proposes constitutive laws describing the non-linear in-plane shear response, which can be alternative for the relations commonly considered in the literature. The proposed equations are...
-
Eigenfaces, Fisherfaces, Laplacianfaces, Marginfaces – How to Face the Face Verification Task
PublikacjaThis paper describes the exhaustive tests of four known methods of linear transformations (Eigenfaces, Fisherfaces, Laplacianfaces and Marginfaces) in the context of face verification task. Additionally, we introduce a new variant of the transformation (Laplacianface + LDA), and the specific interval-based decision rule. Both of them improve the performance of face verification, in general, however, our experiments show that the...
-
3D buckling analysis of a truss with horizontal braces
PublikacjaThe present research is devoted to the study of out-of-plane buckling of a truss with horizontal braces. The truss is a model of real roof truss scaled by factor ¼. A linear buckling and a non-linear analysis with geometric and material nonlinearity were carried out. The truss buckling and limit load for different stiffnesses and number of braces are found. Numerical analysis are verified by experiment. Threshold bracing stiffness...
-
The consideration to the dynamic systems parameter identification
PublikacjaIn this paper, a concept for continuous-time dynamic systems parameter identification using modulating function approach is presented. It refers to linear as well as selected non-linear systems. It shows the possibility of direct application without converting differential equation. In particular cases direct application can decrease the amount of computation in non-linear system identification, which generally requires Fourier...
-
Krzywa przejściowa z wygładzoną krzywizną dla dróg kolejowych
PublikacjaW pracy przedstawiono koncepcję nowej postaci krzywej przejściowej, o liniowym przebiegu krzywizny na długości i wygładzonymi rejonami skrajnymi. Może ona stanowić alternatywę dla tzw. gładkich krzywych przejściowych, o nieliniowym przebiegu krzywizny na całej długości. Została tutaj wykorzystana uniwersalna metoda identyfikacji krzywych przejściowych za pomocą równań różniczkowych. Wyznaczono ogólne równania krzywizny oraz odpowiednie...
-
3D Buckling Analysis of a Truss with Horizontal Braces
PublikacjaThe present research is devoted to the study of out–of–plane buckling of a truss with horizontal braces. The truss is a model of real roof truss scaled by factor 1=4. A linear buckling and a non–linear analysis with geometric and material non–linearity were carried out. The truss buckling and limit load for different stiffnesses and number of braces are found. Numerical analysis are verified by experiment. Threshold bracing stiffness condition...
-
Polyester sail technical woven fabric behaviour under uniaxial and biaxial tensile tests
PublikacjaThe paper is focused on the identification of mechanical properties of a sail technical woven fabric (yacht sailcloth polyester) style 480 AP with MTO (Medium Tempered Optimized) finish. The non-linear elastic behaviour of the fabric applied for sails is investigated under uniaxial and biaxial tensile tests. Comparison of non-linear elastic parameters with others polyester coated fabrics is made. This paper is intended to be an...
-
Improving the accuracy of bearing in active sonar with cylindrical array using spectrum estimation.
PublikacjaThe articles presents a method for improving the accuracy of bearing in multibeam sonar with a cylindrical array. Based on a known spatial spectrum estimation technique, the method has been successfully used in linear array systems. Its accuracy of bearing is satisfactory and ensures a relatively low computational effort. The article discusses certain simplifications and assumptions to adapt the spatial spectrum estimation technique...
-
Stability of roof trusses stiffened by corrugated sheets
PublikacjaThe present parametric study is devoted to the stability analysis of a set of trusses stiffened by decking of corrugated steel sheets. For different parameters of corrugated sheets the critical loading of the roof is calculated. In the parametrical analysis the threshold bracing condition of the roof is obtained. Then the geometrically non-linear analysis of trusses braced by corrugated sheets was conducted. As a results of non-linear...
-
Impact of Low Switching-to-Fundamental Frequency Ratio on Predictive Current Control of PMSM: A simulation study
PublikacjaPredictive current control algorithms for permanent magnet synchronous (PMSM) drives rely on an assumption that within short intervals motor currents can be approximated with linear functions. This approximation may result either from discretizing the motor model or from simplifications applied to the continuous-time model. As the linear current approximation has been recognized as inaccurate in case when the drive operates with...
-
The influence of pressure drop on the working volume of a hydraulic motor
PublikacjaReliability and maintenance analysis of hydraulic positive machines basicly focused on the processes of their wear and failure. But in order to correctly assess the mechanical and volumetric efficiency of a hydraulic motor, both at the stage of development research or at the stage of control tests during its exploitation, the working volume of this motor must be correctly determined. Therefore this paper proposes a new method of...
-
Analytical method of modelling the geometric system of communication route
PublikacjaThe paper presents a new analytical approach to modelling the curvature of a communication route by making use of differential equations. The method makes it possible to identify both linear and nonlinear curvature. It enables us to join curves of the same or opposite signs of curvature. Solutions of problems for linear change of curvature and selected variants of nonlinear curvature in polynomial and trigonometric form were analyzed....
-
Innovative Cold-formed GEB Section under Bending
PublikacjaThis paper is concerned with the numerical bending capacity study of the innovative cold-formed GEB sections. Both linear buckling analysis and non-linear static analysis incorporating geometric and material nonlinearity were carried out employing a shell structural model. The magnitudes of buckling load and limit load with respect to GEB section depth and thickness were obtained. The opened cold-formed section was tested assuming...
-
Comparison of GPS tropospheric delays derived from two consecutive EPN reprocessing campaigns from the point of view of climate monitoring
PublikacjaThe main purpose of this research was to acquire information about consistency of ZTD (zenith total delay) linear trends and seasonal components between two consecutive GPS reprocessing campaigns. The analysis concerned two sets of the ZTD time series which were estimated during EUREF (Reference Frame Sub-Commission for Europe) EPN (Permanent Network) reprocessing campaigns according to 2008 and 2015 MUT AC (Military University...
-
Process engineering in circular economy
Kursy OnlineDefinition and principles of the circular economy (CE). The transition from a linear model to a circular model. Business models for the CE. Circular design and innovation. CE assessment carbon footprint, life cycle assessment. Case studies of the cities implementing the CE concept. CE policy and legislation (EU and Poland). Wastewater treatment plants as an element of the CE. Energy and nutrient recovery technologies in wastewater...
-
An extended basis inexact shift–invert Lanczos for the efficient solution of large-scale generalized eigenproblems
PublikacjaThis paper proposes a technique, based on the Inexact Shift–Invert Lanczos (ISIL) method with Inexact Jacobi Orthogonal Component Correction (IJOCC) refinement, and a preconditioned conjugate-gradient (PCG) linear solver with multilevel preconditioner, for finding several eigenvalues for generalized symmetric eigenproblems. Several eigenvalues are found by constructing (with the ISIL process) an extended projection basis. Presented...
-
Improvement of ships seakeeping performance by application of the full-scale cfd simulations
PublikacjaThe ship’s fuel economy is increasingly important. The paper presents the effect of redesigning a case study ship for increasing seakeeping performance. Selected wave parameters reflect very difficult operational conditions existing on the North Sea and the Baltic Sea. The analyzed variants of a case study ship represent the latest developments of modern hull forms. The concepts similar to V-shaped bulbous bow, X-bow, X-aft, B-bow...
-
Investigation of natural frequencies of axially loaded thin-walled columns
PublikacjaThe paper deals with correlation between natural frequencies of two steel thin-walled columns and the corresponding applied load. The structures are made of cold-formed lipped channel sections. The columns lengths were assumed to follow two buckling patterns – global flexural and flexural-torsional buckling. In the thicker structure two material models were considered – linearly-elastic and elastic-perfectly plastic. Numerical...
-
Stability and load bearing capacity of a truss with elastic braces
PublikacjaThe present paper is devoted to the numerical and experimental investigations of stability of a truss stiffened by elastic braces. The model of a real roof truss scaled by factor ¼ was investigated. In the research the linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity is presented. The initial imperfections were assumed in the form of the first buckling mode....
-
Data-driven models for fault detection using kernel pca:a water distribution system case study
PublikacjaKernel Principal Component Analysis (KPCA), an example of machine learning, can be considered a non-linear extension of the PCA method. While various applications of KPCA are known, this paper explores the possibility to use it for building a data-driven model of a non-linear system-the water distribution system of the Chojnice town (Poland). This model is utilised for fault detection with the emphasis on water leakage detection....
-
Applications of Tensor Analysis in Continuum Mechanics
PublikacjaA tensor field is a tensor-valued function of position in space. The use of tensor fields allows us to present physical laws in a clear, compact form. A byproduct is a set of simple and clear rules for the representation of vector differential operators such as gradient, divergence, and Laplacian in curvilinear coordinate systems. The tensorial nature of a quantity permits us to formulate transformation rules for its components...
-
PI observer stability and application in an induction motor control system
PublikacjaThe paper discusses the problem of stability of a proportional-integral Luenberger observer, designated for the state variables reconstruction of a linear, time-invariant dynamical system.
-
Improvement of ships seakeeping performance by application of the Full-scale CFD simulations – case study
PublikacjaThe ship’s fuel economy is increasingly important. The paper presents the effect of redesigning a case study ship for increasing seakeeping performance. Selected wave parameters reflects very difficult operational con-ditions existing on the North Sea and the Baltic Sea. The analyzed variants of a case study ship represent the latest developments of modern hull forms. The concepts similar to V-shaped bulbous bow, X-bow, X-aft,...
-
NON-LINE ANALYSIS OF STIFFNESS IN COMPRESSION CONDITIONS
PublikacjaThe analyzes were aimed at demonstrating the influence of parameters describing the deformation of the structure on the uncertainty of critical force, and the impact of technological imperfections on stress uncertainty in compression conditions. In a linear buckling analysis, the problem is considered only for the initial, permanent state of the stiffness matrix. In the case of demonstrating the influence of initial deformations...
-
Silver complexes stabilized by large silanethiolate ligands – crystal structures and luminescence properties
PublikacjaBulky silanethiolate and disiladithiolate ligands were applied to synthesize one mononuclear and three trinuclear silver complexes including two cyclic “microclusters” and a linear tri-nuclear silanethiolate complex. All obtained compounds are characterized by X-ray diffraction and FT-IR. NMR and emission spectroscopies were used where possible. The first trinuclear anionic silver thiolate is structurally characterized. The influence...
-
Polypyrrole based gas sensor for ammonia detection
PublikacjaThe nature of polypyrrole response to toxic gases does not allow using the sensor in a conventional way. The main aim of this study is to acquire the information about the concentration using different approaches: a linear approximation, a non-linear approximation and a tangent method. In this paper a two-steps procedure for sensor response measurements has been utilized. Polypyrrole films were electrochemically synthesized on...
-
Stability of an imperfect truss loaded by wind
PublikacjaThe present paper is devoted to the numerical research of stability of a truss loaded by wind and stiffened by elastic supports located at the top chord. The lateral braces or lateral and torsional braces were taken into account. In this paper, the linear buckling analysis re- sults for the beam and shell model were presented. Two different shapes of initial geometric imperfections were considered in the non-linear static analysis...
-
Analysis of sloping brace stiffness influence on stability and load bearing capacity of a truss
PublikacjaThe paper is focused on the numerical study of stability and load bearing capacity of a truss with side elastic braces. The structure is made in reality. The rotational and sliding brace stiffnesses were taken into account. Linear buckling analysis and non-linear static analysis with geometric and material nonlinearity were performed for the beam and shell model of the truss with respect to the angle of sloping braces. As a result...
-
Distance measurement errors in silent FM-CW sonar with matched filtering
PublikacjaThe secretiveness of sonar operation can be achieved by using continuous frequency-modulated sounding signalswith reduced power and significantly prolonged repeat time. The application of matched filtration in the sonarreceiver provides optimal conditions for detection against the background of white noise and reverberation, and avery good resolution of distance measurements of motionless targets. The article shows that target...
-
Fundamentals of classical and analytical mechanics
PublikacjaThe book is a monographic description of the present attempt to Newtonian and Lagrangian mechanics. But also, it could be found as a supplementary educational material useful for the graduate courses in mechanics taken by students majoring in mechanical engineering, physics or physical science. In the book you can find a brief introduction to concepts and principles of algebra of vectors; Kinematics of particles, mainly focused...
-
Liniowe i nieliniowe modele wielowymiarowej kalibracji do predykcji stężenia substancji z pomiarów woltamperometrycznych
PublikacjaPomiary woltamperometryczne znajdują zastosowanie w wielu dziedzinach nauki i techniki, np. w przemyśle farmaceutycznym. Dane uzyskane w wyniku takich pomiarów zawierają informację odnośnie rodzaju i stężenia badanej substancji, jednakże są one często kłopotliwe w bezpośredniej interpretacji. Z tego powodu, istnieje konieczność wykorzystania odpowiednich metod matematycznych, które umożliwiają uzyskanie bezpośredniej i precyzyjnej...
-
Raw data for the paper "Mutually polarizable QM/MM model with in situ optimized localized basis functions"
Dane BadawczeThis dataset contains raw data used to generate plots in the paper Mutually polarizable QM/MM model with in situ optimized localized basis functions. The paper is devoted to a second generation of the TINKTEP model -- an QM/MM approach combining linear-scaling DFT (ONETEP) and a polarizable force field (AMOEBA).
-
ANALYSIS OF BRACE STIFFNESS INFLUENCE ON STABILITY OF THE TRUSS
PublikacjaThe paper is devoted to the numerical and experimental research of stability of a truss with side elastic supports at the top chord. The structure is a model of a real roof truss scaled by factor ¼. The linear buckling analysis and non-linear static analysis were carried out. The buckling length factor for the compressed top chord was calculated and the limit load for the imperfect truss shell model with respect to brace stiffness...
-
Application of the Boundary Element Method for the Simulation of Two-dimensional Viscous Incompressible Flow
PublikacjaThe paper presents the application of an indirect variant of the boundary element method (BEM) to solve the two-dimensional steady flow of a Stokes liquid. In the BEM, a system of differential equations is transformed into integral equations. Thi smakes it possible to limit discretization to the border of the solution. Numerical discretization of the computational domain was performed with linear boundary elements, for which a...
-
A selection of PID type controller settings via LQR approach for two-wheeled balancing robot
PublikacjaThe problem of PID type controller tuning has been addressed in this paper. In particular, a method of selection of PD settings based on the solution of linear–quadratic optimisation problem using the energy criterion has been investigated. Thus, the possibility of transforming optimal settings of the linear–quadratic regulator into the settings of the controller in the classical control system has been given. The presented methodology...
-
METHOD FOR SHIP'S ROLLING PERIOD PREDICTION WITH REGARD TO NON-LINEARITY OF GZ CURVE
PublikacjaThe paper deals with the problem of prediction of the rolling period. A special emphasis is put on the practical application of the new method for rolling period prediction with regard to non-linearity of the GZ curve. The one degree-of-freedom rolling equation is applied with using the non-linear stiffness moment and linear damping moment formulas. A number of ships are considered to research the discrepancies between the pending...
-
Metody strojenia regulatorów typu PID z wykorzystaniem technologii syntezy regulatorów od stanu
PublikacjaUkłady sterujące typu PID są jednymi z najbardziej popularnych regulatorów wykorzystywanych w układach regulacji. W związku z tym znanych jest szereg metod doboru wartości ich parametrów (nastaw). Obok różnych metod inżynierskich czy analitycznych strojenia tego typu regulatorów, dostępne są również podejścia bazujące na optymalizacji. Wskaźnikiem jakości znajdującym w nich zastosowanie jest np. całka z kwadratu uchybu. W artykule...
-
Mieszanie w klasie niejednorodnych łańcuchów Markowa i kwadratowych operatorów stochastycznych
PublikacjaRozprawa doktorska poświęcona jest zagadnieniu asymptotycznych własności w klasie nieskończenie wymiarowych niejednorodnych łańcuchów Markowa z czasem dyskretnym oraz w klasie kwadratowych operatorów stochastycznych. W pierwszej kolejności definiowane są różne rodzaje asymptotycznego zachowania (mieszania) niejednorodnych łańcuchów Markowa odpowiadające zbieżności w normowej i mocnej topologii operatorowej oraz omówione są relacje...
-
Inverse Flood Routing Using Simplified Flow Equations
PublikacjaThe paper considers the problem of inverse flood routing in reservoir operation strategy. The aim of the work is to investigate the possibility of determining the hydrograph at the upstream end based on the hydrograph required at the downstream end using simplified open channel flow models. To accomplish this, the linear kinematic wave equation, the diffusive wave equation and the linear Muskingum equation are considered. To achieve...
-
Stability of a truss under upward wind loading
PublikacjaThe present paper is devoted to the numerical investigations of stability of a truss under upward wind load. The truss is braced at its the upper cord. A structural variant including lateral braces, or lateral and torsional braces is considered. The research presents the problems of linear buckling and non-linear static analysis of the truss shell and beam model with geometric and material non-linearity are presented. The initial...
-
Biomass estimation using a length-weight relationship in beetle larvae (Coleoptera: Aphodiidae, Histeridae, Hydrophilidae, Staphylinidae) obtained from cow dung
PublikacjaThis research enabled the relationship between length and dry body mass to be determined for 158 beetle larvaetaken from cow dung in north-eastern Poland. The larvae were divided into three morphological types, for which the power and linear function of the body length-weight relationship were determined. The linear regression equation characterizes the relationship between body weight and...
-
M-integral for finite anti-plane shear of a nonlinear elastic matrix with rigid inclusions
PublikacjaThe path-independent M-integral plays an important role in analysis of solids with inhomogeneities. However, the available applications are almost limited to linear-elastic or physically non-linear power law type materials under the assumption of infinitesimal strains. In this paper we formulate the M-integral for a class of hyperelastic solids undergoing finite anti-plane shear deformation. As an application we consider the problem...
-
Angular welding distortion - one sided fillet weld
Dane BadawczeWelding is the basic method of joining ship hull elements during its construction. However, this method of joining structural elements generates shrinks. Shrinks causes deformation of the entire welded structure, both linear and angular. In the shipbuilding industry, there is a tendency to oversize fillet welds, at the design as well as manufacturing...
-
Cyclic voltammetry curves for FTO/PANI:WO3 nanocomposite
Dane BadawczeThis dataset contains the results of kinetic electrochemical studies, carried out with cyclic voltammetry (CV) of FTO/PANI:WO3 nanocomposite at various scan rates: 10, 20, 50, 75, 100 and 200 mV/s. The electrolyte was 1M H2SO4 solution. The measurements were performed in a three electrode setup, and with Ag|AgCl|3M KCl as the reference electrode and...
-
Buckling and initial post-local buckling behaviour of cold-formed channel member flange
PublikacjaThe initial post-buckling behaviour of a cold-formed channel member flange after its local buckling is investigated. An axially compressed column or beam subjected to pure bending is considered. The member material is assumed to follow a linear stress-strain relationship. The governing non-linear differential equation of the problem is derived using the minimum total potential energy principle. An approximate solution for the equation...
-
Flexural buckling and post-buckling of columns made of aluminium alloy
PublikacjaThe paper concerns flexural buckling and initial post-buckling of axially compressed columns made of aluminium alloy described by the Ramberg-Osgood relationship. The non-linear differential equation of the problem is derived using the stationary total energy principle and the assumptions of classical beam theory within a finite range. The approximate analytical solution of the equation leading to the buckling loads and initial...