Wyszukiwarka
Filtry
wszystkich: 55
Wyniki wyszukiwania dla: CUBIC C-BEZIER CURVE
-
Modelling of Curvature of the Railway Track Geometrical Layout Using Particle Swarm Optimization
PublikacjaA method of railway track geometrical layout design, based on application of cubic C-Bezier curves for describing the layout curvature is presented in the article. The control points of a cubic C-Bezier curve are obtained in an optimization process carried out using Particle Swarm Optimization algorithm. The optimization criteria are based on the evaluation of the dynamic interactions and satisfaction of geometrical design requirements.
-
Modelling of joining route segments of differential curvature
PublikacjaThe paper presents a new general method of modelling route segments curvature using differential equations. The method enables joining of route segments of different curvature. Transitional curves of linear and nonlinear curvatures have been identified in the case of joining two circular arcs by S-shaped and C-oval transitions. The obtained S-shaped curves have been compared to the cubic C-Bezier curves and to the Pythagorean hodograph...
-
Quantitative assessment of the influence of tensile softening of concrete in beams under bending by numerical simulations with XFEM and cohesive cracks
PublikacjaResults of the numerical simulations of the size effect phenomenon for concrete in comparison with experimental data are presented. In-plane geometrically similar notched and unnotched beams under three-point bending are analyzed. EXtended Finite Element Method (XFEM) with a cohesive softening law is used. Comprehensive parametric study with the respect to the tensile strength and the initial fracture energy is performed. Sensitivity...
-
Surface Texture Analysis of Hardened Shafts after Ceramic Ball Burnishing
PublikacjaThis article represents the results of testing the surface condition of shafts manufactured by the burnishing process. The shafts with a hardness of approximately 62 HRC (Rockwell C). were burnished with a ceramic ball (Si3N4), where the force range was controlled by the means of a hydraulic system. The machining process consisted of hard turning shafts with cubic boron nitride (CBN) inserts, followed by burnishing with the use...
-
Pressure-induced phase transitions in LnTe (Ln=La, Gd, Ho, Yb) and AmTe
PublikacjaThe structural behaviour under compression of different lanthanide (La, Gd, Ho, Yb) and actinide (Am) monochalcogenides is studied by means of in situ high-pressure x-ray diffraction. All the investigated compounds crystallize at ambient conditions within a cubic (B1) NaCl-type structure but show different behaviours at high pressures. LaTe and AmTe undergo B1 to B2 (CsCl-type structure) phase transitions, starting at 9 GPa and...
-
Identification of transition curves in vehicular roads and railways
PublikacjaIn the paper attention is focused on the necessity to systematize the procedure for determining the shape of transition curves used in vehicular roads and railway routes. There has been presented a universal method of identifying curvature in transition curves by using differential equations. Curvature equations for such known forms of transition curves as clothoid, quartic parabola, the Bloss curve, cosinusoid and sinusoid, have...
-
Modelowanie krzywizny układu geometrycznego toru z wykorzystaniem algorytmu PSO
PublikacjaW artykule przedstawiono metodę projektowania układu geometrycznego toru kolejowego opartą na zastosowaniu sześciennych krzywych C-Bezier do opisu krzywizny. Punkty kontrolne krzywej Bezier wyznaczane są w procesie optymalizacji za pomocą algorytmu roju cząstek (Particle Swarm Optimization). Jako kryterium optymalizacji przyjęto minimalizację oddziaływań dynamicznych występujących w układzie tor-pojazd przy spełnieniu warunków...
-
Modelowanie krzywizny i odtwarzanie kształtu geometrycznego układów torowych
PublikacjaW pracy przedstawiono uniwersalna metodę modelowania krzywizny toru kolejowego z wykorzystaniem równań różniczkowych. Rozpatrzono przypadki liniowej i nieliniowej zmiany krzywizny. Przeanalizowano możliwości zastosowania na drogach szynowych kubicznych krzywych C-Bezier oraz PH krzywych Bezier piątego stopnia. Przedstawiono algorytm obliczeniowy do odtwarzania kształtu osi toru kolejowego na podstawie pomiarów satelitarnych oraz...
-
Ocena dynamiczna wybranych sposobów łączenia elementów trasy o zróżnicowanej krzywiźnie
PublikacjaArtykuł przedstawia porównanie właściwości dynamicznych kubicznych krzywych C-Bezier i PH krzywych Bezier piątego stopnia na tle krzywej typu K0 uzyskanej przy zastosowaniu uniwersalnej metody modelowania krzywizny. Właściwości dynamiczne i możliwości zastosowania wymienionych krzywych w projektowaniu dróg kolejowych omówiono na przykładach łączenia krzywą przejścia dwóch łuków kołowych odwrotnych oraz dwóch łuków zgodnych (bez...
-
The Effects of Pin Profile on HDPE Thermomechanical Phenomena during FSW
PublikacjaFriction stir welding (FSW) of polymeric materials has recently attracted significant attention. Herein, we present the effect of the tool pin profile on the FSW of high-density polyethylene (HDPE) joints through joint experimental analysis and thermomechanical simulations. For analysis of pin profile effects on the thermomechanical properties of HDPE joints, frustum (FPT), cubic (CPT), and triangular (TPT) pin shapes were selected...
-
Experimental database of 3D lattice structure scaffolds testing
Dane BadawczeDataset contains results of validation (experimental testing) of 3D lattice scaffolds proposed in the paper "Mathematical approach to design 3D scaffolds for the 3D printable bone implant". There are presented three series of experimental testing for each of seven tested scaffolds:
-
XRD data of (Cr,Fe,Mn,Co,Ni)3O4 High-entropy spinel oxide thin films deposited on amorphous SiO2 substrate by spray pyrolysis techniqe, annealed in a range from 400 to 900oC
Dane BadawczeDataset include collected XRD data of (Cr,Fe,Mn,Co,Ni)3O4 high-entropy spinel oxide thin films deposited by spray pyrolysis technique on amorphous SiO2 substrates and annealed from 400 to 900oC. Samples were prepared in the form of a ~ 500 nm thin film utilising a facile spray pyrolysis technique. The structural and electrical properties of the layers...
-
SEM/EDX data of (Cr,Fe,Mn,Co,Ni)3O4 High-entropy spinel oxide thin films deposited on amorphous SiO2 substrate by spray pyrolysis techniqe
Dane BadawczeThis Data set include SEM and EDX results of (Mn,Co,Fe,Ni,Cr)3O4 high-entropy spinel oxide prepared in the form of a ~ 500 nm thin film utilising a facile spray pyrolysis technique. The structural and electrical properties of the layers were characterised after exposure to temperatures in the range of 400–900 ◦C. The as-deposited layers were amorphous,...
-
TEM data of (Cr,Fe,Mn,Co,Ni)3O4 High-entropy spinel oxide thin films deposited on amorphous SiO2 substrate by spray pyrolysis techniqe
Dane BadawczeThis Dataset include presentation of summarized TEM investigation of (Mn,Co,Fe,Ni,Cr)3O4 high-entropy spinel oxide prepared in the form of a ~ 500 nm thin film utilising a facile spray pyrolysis technique. The structural and electrical properties of the layers were characterised after exposure to temperatures in the range of 400–900 ◦C. The as-deposited...
-
The effect of elevated temperature on LCF damage growth in 2024AA – Experiment and modeling
PublikacjaThis paper presents the results of experimental low-cycle fatigue (LCF) tests conducted on EN-AW 2024 alloy in T3511 temper at 100 ◦C, 200 ◦C and 300 ◦C. The material’s basic fatigue characteristics were determined, such as fatigue life curve and cyclic strain curve. Both the hysteresis loop and nature of fracture surfaces obtained in macro- and microscopic observations (scanning electron microscope, SEM) were accounted for. The...
-
Total electrical conductivity data of (Cr,Fe,Mn,Co,Ni)3O4 High-entropy spinel oxide thin films deposited on amorphous SiO2 substrate by spray pyrolysis techniqe
Dane BadawczeThis dataset includes electrical conductivity measurements results measured by van der pauw technique up to 900oC.
-
Structural properties of mixed conductor Ba1−xGd1−yLax+yCo2O6−δ
PublikacjaBa1−xGd1−yLax+yCo2O6−δ (BGLC) compositions with large compositional ranges of Ba, Gd, and La have been characterised with respect to phase compositions, structure, and thermal and chemical expansion. The results show a system with large compositional flexibility, enabling tuning of functional properties and thermal and chemical expansion. We show anisotropic chemical expansion and detailed refinements of emerging phases as La is...
-
Nickel Oxide Thin Film Sensor for Fluctuation-Enhanced Gas Sensing of Formaldehyde
PublikacjaNanocrystalline nickel-oxide-based thin films were prepared by advanced reactive gas deposition, and the response of these films to formaldehyde was studied by fluctuationenhanced sensing. Morphological and structural analyses showed porous deposits of nickel oxide particles with face-centered cubic structure. Resistance fluctuations were measured upon exposure to ethanol, formaldehyde and methane at 200 °C. Power density spectra...
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublikacjaThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
Chemical investigation of the Al2O3 ultra-thin films
Dane BadawczeUltra-thin layers of oluminum oxide (Al2O3) were deposited by ALD method. Atomic layer deposition provides precise thickness control down to a single atomic layer. The precursors used were trimethylaluminum (Sigma-Aldrich) and purified water. The deposition of the atomic layer was carried out at 200 °C. Samples with a thickness of 2 and 8 nm of alumina...
-
Cross-sections for electron-scattering from 2-methyl-1-buten-3-yne, C 5 H 6 , molecules
PublikacjatCross-sections for electron collisions with the 2-methyl-1-buten-3-yne [H2C C(CH3)C CH] moleculewere measured and calculated. Absolute grand-total electron-scattering cross-section (TCS) was takenat impact energies from 0.6 to 300 eV in the linear electron-transmission experiment. The TCS energydependence for the electron–C5H6collision has two prominent enhancements separated with a deepminimum located near 1.8 eV. In addition,...
-
Połączenie G3 dwóch kierunków prostych z użyciem krzywej NURBS
PublikacjaW artykule przedstawiono nową metodę projektowania układu geometrycznego toru kolejowego opartą na zastosowaniu krzywych NURBS (Non-Uniform Rational B-Spline) do opisu krzywizny. Punkty kontrolne krzywej NURBS wyznaczane są w procesie optymalizacji za pomocą algorytmu genetycznego. Jako kryterium optymalizacji przyjęto minimalizację oddziaływań dynamicznych występujących w układzie tor-pojazd przy spełnieniu warunków geometrycznych...
-
Results of nanoindentation test to calculate residual stress in an eyelet of undercarriage drag strut after laser treatment
Dane BadawczeIn order to determine the residual stress in the laser-processed an eyelet of undercarriage drag strut, a nanoindentation test was performed before and after stress relief annealing. For this purpose, after the hardness test, the sample was subjected to stress relief annealing at 270 °C for 2 hours. Annealing was performed in a vacuum furnace. Hardness...
-
Effect of sintering temperature on electrochemical performance of porous SrTi1-xFexO3-δ (x = 0.35, 0.5, 0.7) oxygen electrodes for solid oxide cells
PublikacjaThis work evaluates the effects of the sintering temperature (800 °C, 900 °C, 1000 °C) of SrTi1-xFexO3-δ (x = 0.35, 0.5, 0.7) porous electrodes on their electrochemical performance as potential oxygen electrode materials of solid oxide cells. The materials were prepared by a solid-state reaction method and revealed the expected cubic perovskite structure. After milling, the powders were characterised by a sub-micrometre particle...
-
Depth profile of the composition of 8 nm Al2O3 thin film
Dane Badawcze8 nm layer of aluminum oxide (Al2O3) was deposited by ALD method on a s. Atomic layer deposition provides precise thickness control down to a single atomic layer. The precursors used were trimethylaluminum (Sigma-Aldrich) and purified water. The deposition of the atomic layer was carried out at 200 °C. To investigate the profile of concenration of...
-
Evaluation of structural and electrical properties of multicomponent spinel oxide thin films deposited via spray pyrolysis technique
PublikacjaThis work reports the preparation of (Mn,Co,Fe,Ni,Cr)3O4 high-entropy spinel oxide in the form of a ~ 500 nm thin film utilising a facile spray pyrolysis technique. The structural and electrical properties of the layers were characterised after exposure to temperatures in the range of 400–900 ◦C. The as-deposited layers were amorphous, and crystallised upon heat treatment at 500 ◦C. Microstructural analyses proved a homogeneous...
-
Thermgravimetric analysis (TGA) data of cement pastes containing pristine and silica-coated bismuth oxide and gadolinium oxide particles
Dane BadawczeThermogravimetric (TGA) data of cement pastes after 2, 7 and 28 days. Samples designations: Control, BG, BG-A and BG-B are associated with the specimen names in the associated publication.
-
Physicochemical properties of Mn1.45Co1.45Cu0.1O4 spinel coating deposited on the Crofer 22 H ferritic steel and exposed to high-temperature oxidation under thermal cycling conditions
PublikacjaThe Crofer 22 H ferritic steel substrate was coated with an Mn1.45Co1.45Cu0.1O4 spinel by means of electrophoresis. After high-temperature oxidation under thermal cycling conditions, the physicochemical properties of the obtained system were evaluated. During 48-h cycles that involved heating the samples up to temperatures of either 750 or 800 °C, the oxidation kinetics of both coated and unmodified steel approximately obeyed...
-
Stabilization of the pyrochlore phase of Mn2Sb2O7 by double substitution
PublikacjaPolycrystalline samples of (Ce4+Mn2+3)(Ga3+Sb5+3)O14 were synthesized by a high-temperature solid-state reaction. In contrast with the parent Mn2Sb2O7 compound that adopts a rhombohedral or monoclinic structure at T > 600 °C, the pyrochlore structure of CeMn3GaSb3O14 is retained up to at least T = 1070°C. High-resolution synchrotron x-ray diffraction measurements show no sign of a superstructure or distortion from cubic symmetry...
-
Chemical composition of tellurium oxides thin films deposited by magnetron sputtering method
Dane BadawczeThin films were prepared by radio frequency reactive magnetron sputtering technique. Metallic Te target was sputtered for about 45 min in argon-oxygen atmosphere what resulted in 300 nm film thickness deposition. The pressure in the chamber was below 0.2 Pa and substrate was heated at 200 °C. The distance between sputtered target and the Corning 1737...
-
Formation of carbon monoxide by radiative association: a quantum dynamical study
PublikacjaRate coefficients for the formation of carbon monoxide (CO) by radiative association of carbon and oxygen atoms are computed using quantum dynamical simulations. At temperatures above 10 K CO radiative association is dominated by C(3P) and O(3P) approaching on the A1Π potential energy curve. The rate coefficient is estimated as k=A(T/300 K)αexp−β/T with A= 1.39 × 10−18 cm3 s−1, α=−0.016 and β= 92.2 for temperatures between 6 and...
-
The electronic characterization of the cubic Laves-phase superconductor CaRh2
PublikacjaWe present the synthesis and experimental characterization of the electronic properties of the cubic Laves phase superconductor CaRh2. Its crystal structure was confirmed by powder X-ray diffraction and its ambient temperature lattice parameter (a = 7.5326(6) Å) is in good agreement with the literature. Magnetization, resistivity and heat-capacity measurements indicate that CaRh2 is a moderate-coupling type-II superconductor (λe-p = 0.89)...
-
Multi-functional sensor based on photonic crystal fiber using plasmonic material and magnetic fluid
PublikacjaA unique highly sensitive photonic crystal fiber is investigated based on plasmonic material and magnetic fluid (MF) for the simultaneous measurement of temperature and magnetic field sensor. The designed sensor is explored by tracing the different parameters such as birefringence, coupling length, power spectrum, and the peak wavelength of the transmission intensity. The magnetic field and temperature computation are attained...
-
Electron-scattering cross sections for selected alkyne molecules: Measurements and calculations
PublikacjaWe report cross-section results from experimental and theoretical studies on electron collisions with 1-butyne (HC≡C–CH2CH3) and acetylene (HC≡CH) molecules and from computations for a propyne (HC≡C–CH3) molecule. Absolute grand -total electron-scattering cross sections (TCSs) were measured at impact energies ranging from about 0.5 to 300 eV using the linear electron-transmission method. The TCS energy curve for 1-butyne has a...
-
Effects of deviations from thermo-rheologically simple behavior of asphalt mixes in creep on developing of master curves of their stiffness modulus
PublikacjaThe paper presents the deviations from the thermo-rheologically simple behavior of asphalt mixes and their effects on the developing of master curves of stiffness modulus. Eleven different mixes were tested in three point bending test under constant load at temperatures –20°C, –10 °C and 0 °C, and in some cases at +10 °C. The test method was developed at the Gdansk University of Technology, Poland. The applied stress level was...
-
Fluctuation-enhanced and conductometric gas sensing with nanocrystalline NiO thin films: A comparison
PublikacjaNanocrystalline thin films of NiO were prepared by advanced reactive gas deposition, and their responses to formaldehyde, ethanol and methane gases were studied via fluctuation-enhanced and conductometric methods Thin films with thicknesses in the 200–1700-nm range were investigated in as-deposited form and after annealing at 400 and 500 °C. Morphological and structural analyses showed porous deposits with NiO nanocrystals having...
-
COMPUTER-AIDED CONSTRUCTION AT DESIGNING REINFORCED CONCRETE COLUMNS AS PER EC
PublikacjaThe article presents the author’s computer program for designing and dimensioning columns in reinforced concrete structures taking into account phenomena affecting their behaviour and information referring to design as per EC. The computer program was developed with the use of C++ programming language. The program guides the user through particular dimensioning stages: from introducing basic data such as dimensions, concrete...
-
Synthesis and thermal studies of flexible polyurethane nanocomposite foams obtained using nanoclay modified with flame retardant compound
PublikacjaThis work presents thermal studies of nanocomposites based on the flexible polyurethane (PU) matrix and filled using montmorillonite organically modified with organophosphorus flame retardant compound. Flexible PU nanocomposite foams were prepared in the reaction carried out between reactive alcoholic hydroxyl and isocyanate groups with the ratio of NCO to OH groups equal to 1.05. The amount of an organoclay ranging from 3 to 9...
-
XPS analysis of TBBO glass
Dane BadawczeGlasses and glass-ceramics with nominal composition 73 TeO2– 4BaO– 3Bi2O3–18SrF2-2RE2O3 (where RE = Eu, Dy) have been synthesized by conventional melt-quenching technique and subsequent heat treatment at 370 °C for 24 h in air atmosphere. Various Eu3+ to Dy3+ molar ratio have been applied to investigate luminescence properties in both glass and glass-ceramic...
-
Prototype of electrochemical sensor for measurements of volatile organic compounds in gases
PublikacjaThe paper presents a laboratory prototype of an electrochemical sensor for measurements of volatile organic compounds (VOCs) in gases, utilizing ionic liquids and commercial screen printed electrodes by DropSens. The following ionic liquids have been tested as the electrolyte and redox reaction environment: 1-butyl, 3-methylimidazolium dicyanoamide ([BMIM][N(CN)2]), 1-octyl, 3-methylimidazolium tetrafluoroborate ([OMIM][BF4]),...
-
Enhancement of self-trapped excitons and near-infrared emission in Bi3+/Er3+ co-doped Cs2Ag0.4Na0.6InCl6 double perovskite
Dane BadawczeErbium (Er) complexes are used as optical gain materials for signal generation in the telecom C-band at 1540 nm, but they need a sensitizer to enhance absorption. Na+ substitution for Ag+ and Bi3+ doping at the In3+ site is a possible strategy to enhance the broadband emission of Cs2AgInCl6, which could be used as a sensitizer for energy transfer to...
-
Electron collisions with methyl-substituted ethylenes: Cross section measurements and calculations for 2-methyl–2-butene and 2,3-dimethyl–2-butene
PublikacjaWe report electron-scattering cross sections determined for 2-methyl–2-butene [(H3C)HC==C(CH3)2] and 2,3-dimethyl–2-butene [(H3C)2C=C(CH3)2] molecules. Absolute grand-total cross sections (TCSs) were measured for incident electron energies in the 0.5–300 eV range, using a linear electron-transmission technique. The experimental TCS energy dependences for the both targets appear to be very similar with respect to the shape. In each...
-
High temperature oxidation behavior of SUS430 SOFC interconnects with Mn-Co spinel coating in air
PublikacjaIn this study, SUS430 alloy is evaluated for its high temperature corrosion properties as a possible material for interconnects of solid oxide fuel cells (SOFCs). Samples are coated with Mn-Co by commercial physical vapor deposition (PVD) process and oxidized in air for 1250 h at 800 °C. A dense cubic Mn-Co-Fe spinel layer is formed on the surface, showing great effect on corrosion reduction compared with the samples without coating....
-
Influence of processing conditions on crystal structure of BiNbO 4 ceramics
PublikacjaBismuth niobate (BiNbO4) has attracted attention as a low-fired ceramics with promising microwave application potential. It belongs to the bismutocolumbite oxides with similarly to scheelite-like stibiotantalite structure (SbTaO4) A3+B5+O4. Aim of the present research was to fabricate BiNbO4 ceramics by solid state reaction route from the mixture of simple oxides viz. Bi2O3, and Nb2O5, and study its phase composition as well as...
-
Studies of the separation performance of silanized silica gel for simulated distillation
PublikacjaWe present the results of investigations of the chromatographic (sorptive) properties of silanized silica gel as a stationary phase for gas chromatography used for simulated distillation. Commercially available silanized sorbent (particle diameter range 63–200 m, average pore size 60 Å) was sieved to obtain the 80–100 mesh fraction (180–150 m). The obtained results revealed that silanized silica gel allows the complete separation...
-
Mn-Co nanofilms on nickel foam measured by XPS mehod
Dane BadawczeManganium-Cobaltium based thin films were electrochemically deposited on a Ni based subsrates in a one-step process at −1.1 V vs. Ag/AgCl in an aqueous solution of differently concentrated Mn(NO3)2·4H2O and Co(NO3)2·6H2O with the deposition time limited by charges of 60, 120, and 200 mC at 25 °C. The concentration ratios of Mn(NO3)2·4H2O to Co(NO3)2·6H2O...
-
Electron scattering from tin tetrachloride (SnCl4) molecules
PublikacjaAbsolute grand-total cross section (TCS) for electron scattering from a tin tetrachloride, SnCl4, molecule was measured at electron-impact energies ranging from 0.6 to 300 eV, in the linear electron-transmission experiment. The measured TCS energy dependence shows two very pronounced enhancements peaking near 1.2 eV and around 9.5 eV, separated with a deep minimum centered close to 3 eV. The low energy structure is attributed to...
-
Enhanced Mechanical and Electromechanical Properties of Compositionally Complex Zirconia Zr1–x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2−δ Ceramics
PublikacjaCompositionally complex oxides (CCOs) or high-entropy oxides (HEOs) are new multi-element oxides with unexplored physical and functional properties. In this work, we report fluorite structure derived compositionally complex zirconia with composition Zr1- x(Gd1/5Pr1/5Nd1/5Sm1/5Y1/5)xO2-δ (x = 0.1 and 0.2) synthesized in solid-state reaction route and sintered via hot pressing at 1350 °C. We explore the evolution of these oxides'...
-
Emissions and toxic units of solvent, monomer and additive residues released to gaseous phase from latex balloons
PublikacjaThis study describes the VOCs emissions from commercially available latex balloons. Nine compounds are determined to be emitted from 13 types of balloons of different colors and imprints in 30 and 60°C. The average values of total volatile organic compounds (TVOCs) emitted from studied samples ranged from 0.054 up to 7.18 μg∙g-1 and from 0.27 up to 36.13 μg∙g-1 for 30oC and 60oC, respectively. The dataset is treated with principal...
-
Uniform expansion estimates in the cubic map as a function of the parameter
Dane BadawczeThis dataset contains selected results of numerical computations described in the paper "Quantitative hyperbolicity estimates in one-dimensional dynamics" by S. Day, H. Kokubu, S. Luzzatto, K. Mischaikow, H. Oka, P. Pilarczyk, published in Nonlinearity, Vol. 21, No. 9 (2008), 1967-1987, doi: 10.1088/0951-7715/21/9/002.